On-Premise
Laundry
Planning
Handbook
CHM2172N
IHF Washer-Extractors
Refer to Installation manual for full instructions.
5-08-53R2
June 2011
Washer-Extractors
Introduction
Model Identification - IHF Washer-Extractors
CHM2172N
Figure 1
IHF033
IHF045
IHF055
IHF075
IHF100
IHF135
IHF165
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-53
2
Washer-Extractors
Specifications and Dimensions - Model IHF033
Capacity (dry weight) Ratio (kg/l)
1:11
1:10
1:9
29 lbs. (13 kg)
32 lbs. (14.5 kg)
35 lbs. (16 kg)
Cylinder
Cylinder diameter, in. (mm)
Cylinder depth, in. (mm)
26.8 (680)
15.76 (400)
31.9 (145)
3
Cylinder volume, ft. (l)
Cabinet
Overall height, in. (mm)
Overall width, in. (mm)
Overall depth, in. (mm)
53.11 (1348)
30.73 (780)
33 (840)
Front Loading
Door opening size, in. (mm)
15.6 (395)
22.26 (565)
30.34 (770)
Height of door bottom above floor, in (mm)
Height of door center above floor, in (mm)
Speed
Wash
10-50 tr/min - RPM
85 tr/min - RPM
Distribution
Low Spin
High Spin
250-500 tr/min - RPM
500-1000 tr/min - RPM
G-factor
Low Spin/High Spin
94 / 380
2.95 HP/2.2 kW
2 (51)
Motor (3 phase), 4p, 1470 tr/min
Drain Valve, in. (mm)
.75 (19)
Water Supply (hard, soft, warm water), in. (mm)
Direct Steam Heating
Steam inlet connection size, in. (mm)
Heating
.38 (10)
Electrical Heating (230/400 V)
Electrical Heating (400V)
Steam
12/15/18 kW
21/24 kW
87 psi (6 bar)
Not Applicable
Not Applicable
Warm Water (without additional heating)
Warm Water (with additional heating)
58.86 X 33.46 X 36.61
(1495 X 850 X 930)
Packing Dimensions (height X width X depth), in. (mm)
Weight
Net weight, lbs. (kg)
Gross weight, lbs. (kg)
935 (424)
970 (440)
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-53
3
Washer-Extractors
Machine Dimensions - Model IHF033
3.46 in.
(88 mm)
8.66 in.
(220 mm)
26.77 in.
(680 mm)
26.18 in.
(665 mm)
1.97 in.
(50 mm)
1.97 in.
(50 mm)
1.34 in.
(34 mm)
1.34 in.
(34 mm)
30.71 in.
(780 mm)
28.86 in.
(733 mm)
29.65 in.
(753 mm)
CHM2173N
CHM2173N
3.41 in.
(86.5 mm)
CHM2174N
CHM2174N
13.07 in. (332 mm)
1
2
10.51 in. (267 mm)
7.95 in. (202 mm)
4.13 in. (105 mm)
7.87 in.
(200 mm)
6.10 in.
(155 mm)
3
4
11
10
5
9
6
7
6.69 in.
(170 mm)
CHM2175N
8
1
2
3
4
5
6
Warm Water Connections .75 in.
Soft Water Connections .75 in.
Connections Clamps
Electrical Connections
Emergency Button
7
8
9
10
11
Hard Water Connections .75 in.
Drain Valve
Steam Connections
Liquid Soap Connections
Ventilation Soap Dispenser
Ventilation Tub
Figure 2
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-53
4
Washer-Extractors
Specifications and Dimensions - Model IHF045
Capacity (dry weight) Ratio (kg/l)
1:11
1:10
1:9
36 lbs. (16.4 kg)
40 lbs. (18 kg)
44 lbs. (20 kg)
Cylinder
Cylinder diameter, in. (mm)
Cylinder depth, in. (mm)
26.8 (680)
19.7 (500)
39.8 (181)
3
Cylinder volume, ft. (l)
Cabinet
Overall height, in. (mm)
Overall width, in. (mm)
Overall depth, in. (mm)
53.11 (1348)
30.73 (780)
37 (940)
Front Loading
Door opening size, in. (mm)
15.6 (395)
22.26 (565)
30.34 (770)
Height of door bottom above floor, in (mm)
Height of door center above floor, in (mm)
Speed
Wash
10-50 tr/min - RPM
85 tr/min - RPM
Distribution
Low Spin
High Spin
250-500 tr/min - RPM
500-1000 tr/min - RPM
G-factor
Low Spin/High Spin
94 / 380
2.95 HP/2.2 kW
2 (51)
Motor (3 phase), 4p, 1470 tr/min
Drain Valve, in. (mm)
.75 (19)
Water Supply (hard, soft, warm water), in. (mm)
Direct Steam Heating
Steam inlet connection size, in. (mm)
Heating
.38 (10)
Electrical Heating (230/400 V)
Electrical Heating (400V)
Steam
12/15/18 kW
21/24 kW
87 psi (6 bar)
Not Applicable
Not Applicable
Warm Water (without additional heating)
Warm Water (with additional heating)
58.86 X 33.46 X 40.55
(1495 X 850 X 1030)
Packing Dimensions (height X width X depth), in. (mm)
Weight
Net weight, lbs. (kg)
Gross weight, lbs. (kg)
1001 (454)
1036 (470)
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-53
5
Washer-Extractors
Machine Dimensions - Model IHF045
3.46 in.
8.66 in.
(88 mm)
(220 mm)
26.77 in.
(680 mm)
30.12 in.
(765 mm)
1.97 in.
(50 mm)
1.97 in.
(50 mm)
1.34 in.
(34 mm)
1.34 in.
(34 mm)
30.71 in.
(780 mm)
32.80 in.
(833 mm)
33.58 in.
(853 mm)
CHM2173N
CHM2173N
3.41 in.
(86.5 mm)
CHM2174N
CHM2174N
13.07 in. (332 mm)
1
2
10.51 in. (267 mm)
7.95 in. (202 mm)
4.13 in. (105 mm)
7.87 in.
(200 mm)
6.10 in.
(155 mm)
3
4
11
10
5
9
6
7
6.69 in.
(170 mm)
CHM2175N
8
1
2
3
4
5
6
Warm Water Connections .75 in.
Soft Water Connections .75 in.
Connections Clamps
Electrical Connections
Emergency Button
7
8
9
10
11
Hard Water Connections .75 in.
Drain Valve
Steam Connections
Liquid Soap Connections
Ventilation Soap Dispenser
Ventilation Tub
Figure 3
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-53
6
Washer-Extractors
Specifications and Dimensions - Model IHF055
Capacity (dry weight) Ratio (kg/l)
1:11
1:10
1:9
47 lbs. (21.3 kg)
52 lbs. (23.4 kg)
57 lbs. (26 kg)
Cylinder
Cylinder diameter, in. (mm)
Cylinder depth, in. (mm)
29.53 (750)
20.87 (530)
51.5 (234)
3
Cylinder volume, ft. (l)
Cabinet
Overall height, in. (mm)
Overall width, in. (mm)
Overall depth, in. (mm)
59.25 (1505)
35.43 (900)
38.78 (985)
Front Loading
Door opening size, in. (mm)
15.6 (395)
24.8 (630)
32.28 (820)
Height of door bottom above floor, in (mm)
Height of door center above floor, in (mm)
Speed
Wash
10-50 tr/min - RPM
100 tr/min - RPM
Distribution
Low Spin
High Spin
250-500 tr/min - RPM
500-1000 tr/min - RPM
G-factor
Low Spin/High Spin
74 / 373
4.08 HP/3.0 kW
3 (76)
Motor (3 phase), 4p, 1470 tr/min
Drain Valve, in. (mm)
.75 (19)
Water Supply (hard, soft, warm water), in. (mm)
Direct Steam Heating
Steam inlet connection size, in. (mm)
Heating
.5 (13 )
Electrical Heating (230/400 V)
Electrical Heating (400V)
Steam
12/15/18 kW
24 kW
87 psi (6 bar)
Not Applicable
Not Applicable
Warm Water (without additional heating)
Warm Water (with additional heating)
65 X 41 X 46
(1650 X 1020 X 1150)
Packing Dimensions (height X width X depth), in. (mm)
Weight
Net weight, lbs. (kg)
Gross weight, lbs. (kg)
1257 (570)
1389 (630)
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-53
7
Washer-Extractors
Machine Dimensions - Model IHF055
2.36 in.
9.45 in.
(60 mm)
(240 mm)
1
29.06 in.
32.68 in.
(830 mm)
1.38 in.
(35 mm)
1.38 in.
(35 mm)
3.19 in.
(81 mm)
3.19 in.
(81 mm)
(738 mm)
35.43 in.
(900 mm)
36.46 in.
(926 mm)
36.99 in.
(939.5 mm)
2.76 in.
(70 mm)
CHM2176N
CHM2176N
CHM2177N
CHM2177N
2
3
13.62 in.
(346 mm)
9.88 in.
6.81 in.
(251 mm)
(173 mm)
3.70 in.
6.12 in.
(94 mm)
(155.5 mm)
4
11
10
5
6
9
4.13 in.
(105 mm)
8
7
CHM2178N
CHM2178N
1
2
3
4
5
6
Emergency Button
7
8
9
10
11
Drain Valve
Steam Connections
Liquid Soap Connections
Hard Water Connections .75 in.
Ventilation Soap Dispenser
Warm Water Connections .75 in.
Soft Water Connections .75 in.
Connections Clamps
Electrical Connections
Ventilation Tub
Figure 4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-53
8
Washer-Extractors
Mounting Bolt Hole Locations - Model IHF055
1.73 in.
(44 mm)
43.7 in.
(1110 mm)
29.06 in.
(738 mm)
3.19 in.
(81 mm)
2.36 in.
(60 mm)
35.43 in.
(900 mm)
CHM2179N
CHM2179N
Figure 5
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-53
9
Washer-Extractors
Installation - Models IHF033, IHF045
and IHF055
Electrical Installation Requirements
- Models IHF033, IHF045 and IHF055
Ground
Machine with steam heating or boiler fed
machines without additional electrical heating
The machine must be placed on a flat, solid surface
(metal base, concrete or solid ground). It is
recommended that the machine be anchored on the
provided places (1) in the base, especially in case of a
220V 3AC
16 A
380V 3AC + N
16 A
Machine with electrical heating
220V 3AC
380V 3AC + N
16 A
9 kW
12 kW
15 kW
18 kW
21 kW
24 kW
25 A
40 A
50 A
50 A
N/A
N/A
20 A
25 A
32 A
40 A
40 A
1
Table 1
CHM2180N
1
Mounting Bolt Holes
Figure 6
The machine must be placed entirely level. For easy
maintenance it is recommended to keep a minimal
distance of 23.62 in. (600 mm) between the wall and
the back of the machine.
If several machines are placed next to each other, there
should be a minimal distance of 1.18 in. (30 mm)
between each machine.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-53
10
Washer-Extractors
Specifications and Dimensions - Model IHF075
Capacity (dry weight) Ratio (kg/l)
1:11
1:10
1:9
62 lbs. (28 kg)
67 lbs. (30.4 kg)
73 lbs. (33.3 kg)
Cylinder
Cylinder diameter, in. (mm)
Cylinder depth, in. (mm)
33.46 (850)
21.14 (537)
66.9 (304)
3
Cylinder volume, ft. (l)
Cabinet
Overall height, in. (mm)
Overall width, in. (mm)
Overall depth, in. (mm)
60.23 (1530)
41.73 (1060)
38.58 (980)
Front Loading
Door opening size, in. (mm)
15.55 (395)
24.80 (630)
32.28 (820)
Height of door bottom above floor, in (mm)
Height of door center above floor, in (mm)
Speed
Wash
10-50 tr/min - RPM
100 tr/min - RPM
Distribution
Low Spin
High Spin
250-500 tr/min - RPM
500-1000 tr/min - RPM
G-factor
Low Spin
High Spin
84
383
5.36 HP/4.0 kW
Motor (3 phase), 4p, 1470 tr/min
Drain Valve, in. (mm)
Depend-O-Drain
3 (76)
2 (51)
Option
.75 (19)
Water Supply (hard, soft, hot water & cool-down), in. (mm)
Direct Steam Heating
Steam inlet connection size, in. (mm)
Electrical
.5 (13)
Electrical Heating (220/380 V)
Electrical Heating (380V)
Steam
18 kW
18 kW - 24 kW - 30 kW
Not Applicable
Warm Water (without additional heating)
Warm Water (with additional heating)
Not Applicable
Not Applicable
68 X 46 X 48
(1730 X 1160 X 1230)
Packing Dimensions (height X width X depth), in. (mm)
Weight
Net weight, lbs. (kg)
Gross weight, lbs. (kg)
1907 (865)
2090 (948)
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-53
11
Washer-Extractors
Machine Dimensions - Model IHF075
42.52 in.
41.73 in.
(1080 mm)
(1060 mm)
34.25 in.
(870 mm)
2.56 in.
(65 mm)
37.80 in.
CHM2181N
CHM2181N
(960 mm)
CHM2182N
CHM2182N
2
3
4
1
5
6
5.91 in.
(150 mm)
11.42 in.
(290 mm)
7.87 in. (200 mm)
12.60 in. (320 mm)
3.15 in.
(80 mm)
17.32 in.
(440 mm)
5.71 in.
(145 mm)
11.02 in.
(280 mm)
8
7
CHM2183N
CHM2183N
1
2
3
4
Output Steam Valve
5
6
7
8
Electrical Connection
Electrical Connection Clamps
Water Drain
Hard Water Connections .75 in.
Warm Water Connections .75 in.
Soft Water Connections .75 in.
Steam Connection
Figure 7
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-53
12
Washer-Extractors
Mounting Bolt Hole Locations - Model IHF075
1.38 in.
(35 mm)
50.87 in.
(1292 mm)
34.06 in.
(865 mm)
3.84 in.
(97.5 mm)
2.56 in.
(65 mm)
41.73 in.
(1060 mm)
CHM2179N
CHM2179N
Figure 8
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-53
13
Washer-Extractors
Installation - Model IHF075
Electrical Installation Requirements
- Model IHC075
Ground
Machine with steam heating or boiler fed
The machine must be placed on a flat, solid surface
(metal base, concrete or solid ground). It is
recommended that the machine be anchored on the
provided places (1) in the base, especially in case of a
machines without additional electrical heating
220V 3AC
16 A
380V 3AC + N
16 A
Machine with electrical heating
220V 3AC
380V 3AC + N
32 A
18 kW
21 kW
24 kW
30 kW
50 A
N/A
N/A
N/A
40 A
40 A
50 A
Table 2
1
CHM2180N
1
Mounting Bolt Holes
Figure 9
The machine must be placed entirely level. For easy
maintenance it is recommended to keep a minimal
distance of 23.62 in. (600 mm) between the wall and
the back of the machine.
If several machines are placed next to each other, there
should be a minimal distance of 1.18 in. (30 mm)
between each machine.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-53
14
Washer-Extractors
Specifications and Dimensions - Model IHF100
Capacity (dry weight) Ratio (kg/l)
1:11
1:10
1:9
90.17 lbs. (40.9 kg)
99.21 lbs. (45 kg)
110.23 lbs. (50 kg)
Cylinder
Cylinder diameter, in. (mm)
Cylinder depth, in. (mm)
38.58 (980)
23.50 (597)
118.9 (450)
3
Cylinder volume, ft. (l)
Cabinet
Overall height, in. (mm)
Overall width, in. (mm)
Overall depth, in. (mm)
76.77 (1950)
47.24 (1200)
46.85 (1190)
Front Loading
Door opening size, in. (mm)
15.55 (395)
31.50 (800)
39.37 (1000)
Height of door bottom above floor, in (mm)
Height of door center above floor, in (mm)
Speed
Wash
10-50 tr/min - RPM
100 tr/min - RPM
Distribution
Spin
250-400 tr/min - RPM
500-800 tr/min - RPM
High Spin
G-factor
Spin
87
350
High Spin
10.05 HP/7.5 kW
3 (76)
Motor (3 phase), 4p, 1470 tr/min
Drain Valve, in. (mm)
.75 (19)
Water Supply (hard, soft, hot water), in. (mm)
Direct Steam Heating
Steam inlet connection size, in. (mm)
Electrical
.5 (13)
Electrical Heating (220/380 V)
Electrical Heating (380 V)
Steam
27 kW
36 kW
Not Applicable
Not Applicable
Not Applicable
Warm Water (without additional heating)
Warm Water (with additional heating)
Packing Dimensions (height X width X depth), in. (mm)
Without Liquid Soap Pumps
83 X 53 X 56
(2100 X 1350 X 1430)
With Liquid Soap Pumps
83 X 61 X 56
(2100 X 1550 X 1430)
Weight
Net weight, lbs. (kg)
Gross weight, lbs. (kg)
2205 (1000)
2646 (1200)
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-53
15
Washer-Extractors
Machine Dimensions - Model IHF100
47.24 in.
(1200 mm)
52.56 in.
(1335 mm)
4.33 in.
(110 mm)
40.94 in.
(1040 mm)
4.53 in.
39.76 in.
(115 mm)
(1010 mm)
CHM2186N
CHM2186N
CHM2187N
CHM2187N
3
6.69 in.
1.97 in.
(170 mm)
(50 mm)
2
1
2
12.01 in.
(305 mm)
9.25 in.
(235 mm)
9.84 in.
(250 mm)
6.89 in.
(175 mm)
6.5 in.
(165 mm)
4.53 in.
(115 mm)
4
4.13 in.
(105 mm)
8.86 in.
(225 mm)
6.5 in.
(165 mm)
2
2.17 in.
(55 mm)
5
8.66 in.
(220 mm)
10
2.95 in.
(75 mm)
7.28 in.
(185 mm)
7
9
8
6
8.46 in.
8.46 in.
(215 mm)
(215 mm)
CHM2188N
1
2
3
4
5
Ventilation Tub
Electrical Connections
Electrical Connection Soap Pumps
Main Switch
6
7
8
9
10
Water Drain
Soft Water Connections .75 in.
Warm Water Connections .75 in.
Hard Water Connections .75 in.
Connection of the Liquid Soap Hoses
Steam Connection .5 in.
Figure 10
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-53
16
Washer-Extractors
Mounting Bolt Hole Locations - Model IHF100
1.73 in.
(44 mm)
57.09 in.
(1450 mm)
40.87 in.
(1038 mm)
3.19 in.
(81 mm)
2.76 in.
(70 mm)
47.24 in.
(1200 mm)
CHM2179N
CHM2179N
Figure 11
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-53
17
Washer-Extractors
Specifications and Dimensions - Model IHF135
Capacity (dry weight) Ratio (kg/l)
1:11
1:10
1:9
114 lbs. (51.8 kg)
126 lbs. (57 kg)
140 lbs. (63.3 kg)
Cylinder
Cylinder diameter, in. (mm)
Cylinder depth, in. (mm)
38.58 (980)
30.51 (775)
150.6 (570)
3
Cylinder volume, ft. (l)
Cabinet
Overall height, in. (mm)
Overall width, in. (mm)
Overall depth, in. (mm)
76.77 (1950)
47.24 (1200)
55.31 (1405)
Front Loading
Door opening size, in. (mm)
15.55 (395)
31.50 (800)
39.37 (1000)
Height of door bottom above floor, in (mm)
Height of door center above floor, in (mm)
Speed
Wash
10-50 tr/min - RPM
100 tr/min - RPM
Distribution
Spin
250-400 tr/min - RPM
500-800 tr/min - RPM
High Spin
G-factor
Spin
87
350
High Spin
10.05 HP/7.5 kW
3 (76)
Motor (3 phase), 4p, 1470 tr/min
Drain Valve, in. (mm)
.75 (19)
Water Supply (hard, soft, hot water), in. (mm)
Direct Steam Heating
Steam inlet connection size, in. (mm)
Electrical
.5 (13)
Electrical Heating (220/380 V)
Electrical Heating (380 V)
Steam
27 kW
36 kW
Not Applicable
Not Applicable
Not Applicable
Warm Water (without additional heating)
Warm Water (with additional heating)
Packing Dimensions (height X width X depth), in. (mm)
Without Liquid Soap Pumps
83 X 53 X 64
(2100 X 1350 X 1630)
With Liquid Soap Pumps
83 X 53 X 64
(2100 X 1550 X 1630)
Weight
Net weight, lbs. (kg)
Gross weight, lbs. (kg)
2425 (1100)
2866 (1300)
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-53
18
Washer-Extractors
Machine Dimensions - Model IHF135
47.24 in.
(1200 mm)
59.06 in.
(1500 mm)
4.33 in.
(110 mm)
40.94 in.
(1040 mm)
4.53 in.
46.65 in.
(115 mm)
(1185 mm)
CHM2186N
CHM2186N
CHM2187N
CHM2187N
3
1.97 in.
(50 mm)
6.69 in.
(170 mm)
2
1
2
12.01 in.
(305 mm)
9.25 in.
(235 mm)
9.84 in.
(250 mm)
6.89 in.
(175 mm)
6.5 in.
4.53 in.
(115 mm)
(165 mm)
4
4.13 in.
(105 mm)
8.86 in.
(225 mm)
6.5 in.
2
(165 mm)
2.17 in.
(55 mm)
5
8.66 in.
(220 mm)
10
2.95 in.
(75 mm)
7.28 in.
(185 mm)
7
9
8
8.46 in.
(215 mm)
6
8.46 in.
(215 mm)
CHM2188N
1
2
3
4
5
Ventilation Tub
Electrical Connections
Electrical Connection Soap Pumps
Main Switch
6
7
8
9
10
Water Drain
Soft Water Connections .75 in.
Warm Water Connections .75 in.
Hard Water Connections .75 in.
Steam Connection .5 in.
Connection of the Liquid Soap Hoses
Figure 12
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-53
19
Washer-Extractors
Mounting Bolt Hole Locations - Model IHF135
1.73 in.
(44 mm)
61.92 in.
(1573 mm)
40.87 in.
(1038 mm)
3.19 in.
(81 mm)
2.76 in.
(70 mm)
47.24 in.
(1200 mm)
CHM2179N
CHM2179N
Figure 13
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-53
20
Washer-Extractors
Installation - Models IHF100 and
IHF135
Electrical Installation Requirements
- Models IHF100 and IHF135
Ground
Machine without electrical heating
220V 3AC
20 A
380V 3AC + N
The machine must be placed on a flat, solid surface
(metal base, concrete or solid ground). It is
recommended that the machine be anchored (M16) on
the provided places (1) in the base, especially in case
20 A
Machine with electrical heating
220V 3AC
380V 3AC + N
63 A
27 kW
36 kW
80 A
N/A
80 A
Table 3
1
CHM2180N
1
Mounting Bolt Holes
Figure 14
The machine must be placed entirely level. For easy
maintenance it is recommended to keep a minimal
distance of 23.62 in. (600 mm) between the wall and
the back of the machine.
If several machines are placed next to each other, there
should be a minimal distance of 1.18 in. (30 mm)
between each machine.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-53
21
Washer-Extractors
Specifications and Dimensions - Model IHF165
Capacity (dry weight) Ratio (kg/l)
1:11
1:10
1:9
147 lbs. (66.5 kg)
160 lbs. (73 kg)
180 lbs. (81.5 kg)
Cylinder
Cylinder diameter, in. (mm)
Cylinder depth, in. (mm)
43.11 (1095)
30.51 (775)
192.8 (730)
3
Cylinder volume, ft. (l)
Cabinet
Overall height, in. (mm)
Overall width, in. (mm)
Overall depth, in. (mm)
82.68 (2100)
51.18 (1300)
63.78 (1620)
Front Loading
Door opening size, in. (mm)
24.49 (622)
27.95 (710)
40.16 (1020)
Height of door bottom above floor, in (mm)
Height of door center above floor, in (mm)
Speed
Wash
10-50 tr/min - RPM
100 tr/min - RPM
Distribution
Spin
250-750 tr/min - RPM
G-factor
Spin
344
15.42 HP/11.5 kW
3 (76)
Motor (3 phase), 4p, 1470 tr/min
Drain Valve, in. (mm)
1 (25)
Water Supply (hard, soft, hot water), in. (mm)
Direct Steam Heating
Steam inlet connection size, in. (mm)
Electrical
.75 (19)
Electrical Heating (240 V)
Electrical Heating (400V)
Steam
27 kW
36 kW
Not Applicable
Not Applicable
Not Applicable
Warm Water (without additional heating)
Warm Water (with additional heating)
90.55 X 57.09 X 67.72
(2300 X 1450 X 1720)
Packing Dimensions (height X width X depth), in. (mm)
Weight
Net weight, lbs. (kg)
Gross weight, lbs. (kg)
4630 (2100)
5181 (2350)
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-53
22
Washer-Extractors
Machine Dimensions - Model IHF165
63.78 in.
(1620 mm)
51.18 in.
(1300 mm)
4.53 in.
(115 mm)
46.65 in.
(1185 mm)
44.88 in.
(1140 mm)
CHM2195N
CHM2195N
CHM2196N
CHM2196N
3
7.68 in.
1.97 in.
(195 mm)
(50 mm)
1
10.24 in.
(260 mm)
2
13.19 in.
(335 mm)
9.65 in.
(245 mm)
6.89 in.
(175 mm)
4.53 in.
(115 mm)
6.5 in.
(165 mm)
2
4
4.13 in.
(105 mm)
8.86 in.
(225 mm)
6.5 in.
(165 mm)
2.17 in.
(55 mm)
2
5
8.66 in.
(220 mm)
11
2.95 in.
(75 mm)
7
8
9
10
10.04 in.
(255 mm)
10.04 in.
(255 mm)
6
CHM2197N
CHM2197N
1
2
3
4
5
6
Ventilation Tub
Electrical Input
Electrical Connection Liquid Soap
Electrical Connection
Steam Connection
7
8
9
10
11
Soft Water Connections 3/4 in.
Soft Water Connections 1 in.
Warm Water Connections 1 in.
Hard Water Connections 1 in.
Input Liquid Soap
Water Drain
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-53
23
Washer-Extractors
Figure 15
Mounting Bolt Hole Locations - Model IHF165
1.73 in.
(44 mm)
64.72 in.
(1644 mm)
44.80 in.
(1138 mm)
3.19 in.
(81 mm)
2.76 in.
(70 mm)
51.18 in.
(1300 mm)
CHM2179N
CHM2179N
Figure 16
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-53
24
Washer-Extractors
Installation - Model IHF165
Electrical Installation Requirements
- Model IHF165
Ground
Machine without electrical heating
The machine must be placed on a flat, solid surface
(metal base, concrete or solid ground). It is
recommended that the machine be anchored (M16) on
the provided places (1) in the base, especially in case
of a plinth (See Mounting Bolt Hole Locations). Refer
240V 3AC
40 A
400V 3AC + N
25 A
Machine with electrical heating
240V 3AC
400V 3AC + N
63 A
27 kW
36 kW
125 A
N/A
80 A
Table 4
1
CHM2180N
1
Mounting Bolt Holes
Figure 17
The machine must be placed entirely level. For easy
maintenance it is recommended to keep a minimal
distance of 23.62 in. (600 mm) between the wall and
the back of the machine.
If several machines are placed next to each other, there
should be a minimal distance of 1.18 in. (30 mm)
between each machine.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-53
25
|
