InFocus Projector SP CEIL 008 User Manual

Hardware description  
The Digital Projector Mount utilizes the following hardware. Note that the letters associated with the hardware  
on this list correspond to the letters listed in the instructions for each installation method.  
A. Four (4) 4 (mm) x 10 (mm) Phillips head screws (supplied)  
27700B S.W. Parkway Ave.  
Wilsonville, Oregon 97070-9215  
1-800-294-6400  
SP-CEIL-008 DIGITAL PROJECTOR MOUNT  
Installation Instructions  
B. One (1) mounting bracket (supplied)  
These are the installation instructions for your Digital Projector Mount. Included are four methods of  
installation.  
Select the method that works best for your viewing situation. The methods are:  
°
°
Fixed Height Ceiling Installationbest for short ceilings, eight (8’) or lower  
Adjustable Height Ceiling Installationbest for high ceilings, nine (9’) feet or higher  
(optional) SP-LTMT-EXTP-S height adjustable extension is required.  
C. Digital Projector (not included)  
D. One (1) Litemount Plus® assembly (supplied)  
°
Wall Mount Installationfor installing the Digital Projector Mount on a rear wall the  
(optional) SP-LTMT-EXTP-S height adjustable extension is required.  
NOTE: If the required height range is greater than 12½", the optional SP-LTMT-EXTP could be used to  
extend the length of the suspension adapter. For further information or ordering assistance, please contact us  
at the phone number and address listed at the top of this column.  
Before You Start the Installation  
The wall or ceiling where you want to install the digital projector must be capable of supporting a weight that is  
five (5) times the weight of 7lbs the projector you are installing. Consult the projector’s documentation for  
weight specifications. If the wall, ceiling, tabletop, shelf, or floor is not strong enough to handle five (5) times  
the weight of 7lbs, then you must reinforce the installation environment. If you are unsure about the  
installation environment, please consider having it reinforced and having the projector installed by qualified  
personnel. Failure to do so could result in serious personal injury and damage to the projector.  
NOTE: Hardware item (E) is what secures the Digital Projector Mount to your ceiling, wall, tabletop, floor.  
Make sure you consult with your local hardware store staff for the type of hardware that works best for your  
installation environment.  
E. SINGLE WOOD STUD: If mounting on a single wood stud use three (3) #14 x 2" Lag bolts (minimum)  
commercially available. Use the mounting points on the center of the plate as indicated in the assembly  
diagram.  
To avoid personal injury, use only an approved projector mount. Using an unauthorized projector mount may  
lead to poor ventilation and projector failure.  
° SOLID STRUCTURE: If mounting to a solid structure use four (4) 5/16" x 2" Lag bolts or commercially  
available hardware (depending on the installation requirements). Use the mounting points found on the outer  
points of the mounting plate as indicated in the assembly diagram.  
When installing the projector mount, keep in mind that the projector’s focus ring is not squarely in the center  
of the front of the projector, but offset by several inches. Make sure that when you mount the projector you  
offset the installation to match the amount of inches that the projector’s focus ring is offset from the center of  
the front of the projector.  
F. Allen wrench (supplied)  
R
LISTED  
E176225  
Copyright by InFocus Corporation  
Wilsonville, OR. All rights reserved  
1
 
Wood stud  
E
Adjustable Height Ceiling Installation  
Complete the following steps to install the projector mount and projector on your ceiling with the optional  
suspension adapter.  
Ceiling structure  
Center of wood stud  
This installation works best with high ceilings (FIGURE 3).  
D
Note: Look at the bottom of the upper assembly (D) and locate the arrow. Make sure you install the projector  
mount with the arrow pointing toward your screen.  
6.  
7.  
Use the Allen wrench (F) to remove the upper plate from the mount assembly (D).  
Use the Allen wrench to remove the two screws from the enclosed end of the of the suspension  
adapter, and place it into the slotted extension on the upper plate (E). Make sure that the two (2) outer  
holes on the suspension adapter align with the holes on the slotted extension on the upper plate.  
8.  
9.  
Replace the two screws removed in step 2 into the two (2) holes to secure the suspension adapter to  
the upper plate.  
Attach the mount assembly to the suspension adapter and secure them with the two screws removed  
in step 1.  
C
Insert and rotate 180°  
and lock down  
10. Secure the upper assembly to the ceiling using the commercially available hardware (E) suitable for  
your environment. Be sure that the upper assembly arrow is pointing toward your screen.  
11. Carefully raise the projector (C) with the mounting bracket (B) attached and insert it into the bottom of  
the upper assembly (D) by its tabs.  
12. Rotate the projector (C) with the mounting bracket (B) attached 180º so that the projector’s focus ring  
is pointing toward your screen.  
13. Align the safety knob on the mount assembly with the end of the arrow-shaped slot on the mounting  
B
bracket (B) and screw it through the opening to prevent further rotation. Hand-tighten the safety knob.  
14. Hand-tighten the remaining two tension knobs to secure the mounting bracket to the amount  
assembly.  
A
C
CAUTION: Check all of the hardware for proper tightness and security. Do not over-tighten the screws.  
SEE FIGURE 3  
Solid ceiling structure  
NOTE: Use the Allen wrench key (F) for the following modification  
D
E
C
Insert and rotate 180°  
and lock down  
B
C
A
3
 
Wood stud  
FIGURE3  
E
Ceiling plate  
Ceiling structure  
Remove  
from mount  
assembly  
Center of wood stud  
Adjustable screws  
Remove  
from mount  
assembly  
D
Optional  
SP-LTMT-EXTP-S  
extension adapter  
Ceiling plate  
C
Insert and rotate 180°  
and lock down  
Mount  
assembly  
B
A
Replace the  
hardware  
C
Solid ceiling structure  
Optional  
SP-LTMT-EXTP-S  
extension adapter  
D
E
Adjustable screws  
Optional  
SP-LTMT-EXTP-S  
extension adapter  
Adjustable screws  
WARNING  
When using the optional  
extension adapters and making  
a height adjustment while  
secured to the wall or ceiling do  
not remove the screws  
completely from the extension.  
Failure to do so could result in  
injury and damage to the  
projector.  
Replace the  
hardware  
Insert and rotate 180°  
and lock down  
C
B
C
A
4
 
Wall Mount Installation  
Complete the following steps to install the projector mount and projector to your wall. (FIGURE 4)  
Wall wood stud  
Wall structure  
Note: Look at the bottom of the upper assembly (D) and locate the arrow. Make sure you install the projector  
mount with the arrow pointing toward your screen.  
Top plate  
NOTE: Follow step 3 to secure the extension to the mount assembly.  
15. Secure the upper plate to the wall using the commercially available hardware (E) suitable for your  
environment. Be sure that the screen indicator arrow is pointing toward your screen.  
16. Carefully raise the projector (C) with the mounting bracket (B) attached and insert it into the bottom of  
Optional  
SP-LTMT-EXTP-S  
extension adapter  
the mount assembly by its tabs.  
17. Rotate the projector (C) with the mounting bracket (B) attached 180º so that the projector’s focus rings  
E
is pointing toward your screen.  
18. Align the safety knob on the mount assembly with the end of the arrow-shaped slot on the mounting  
Adjustable screws  
bracket (B) and screw it through the opening to prevent further rotation. Hand-tighten the securing  
knob.  
19. Hand-tighten the remaining two tension knobs to secure the mounting bracket (B) to the mount  
assembly (D).  
B
CAUTION: Check all of the hardware for proper tightness and security. Do not over-tighten the screws.  
SEE FIGURE 4  
NOTE: Use the Allen wrench key (F) for the following modification  
C
B
WARNING  
C
When using the optional  
extension adapters and making  
a height adjustment while  
secured to the wall or ceiling do  
not remove the screws  
completely from the extension.  
Failure to do so could result in  
injury and damage to the  
projector.  
5
 

Indesit Refrigerator IN S 1611 UK User Manual
Infinity Speaker System Primus Series User Manual
InFocus Projector SP LAMP 084 User Manual
Jabra Headphones JXO Bluetooth Headset User Manual
Jacuzzi Hot Tub EA00 LH User Manual
John Lewis Washer JLWM 1404 User Manual
JVC Car Amplifier KW NT50HDT User Manual
Kenwood CD Player D R350 User Manual
Kicker Stereo System iK501 User Manual
KitchenAid Food Processor KSM1FPA User Manual