Indesit Washer GB Washing Machine User Manual

Instructions for use  
WASHING MACHINE  
Contents  
GB  
Installation, 2-3  
Unpacking and levelling, 2  
Electric and water connections, 2-3  
The first wash cycle, 3  
GB  
English  
Technical details, 3  
Washing machine description, 4-5  
Control panel, 4  
Display, 5  
“MEMO” Programme, 5  
Starting and Programmes, 6  
Briefly: how to start a programme, 6  
Programme table, 6  
Personalisations, 7  
Setting the spin cycle, 7  
Setting the Delay Timer, 7  
Setting the temperature, 7  
Functions, 7  
WIXE 127  
Detergents and laundry, 8  
Detergent dispenser, 8  
Bleach cycle, 8  
Preparing your laundry, 8  
Special items, 8  
Precautions and advice, 9  
General safety, 9  
Disposal, 9  
Saving energy and respecting the environment, 9  
Care and maintenance, 10  
Cutting off the water or electricity supply, 10  
Cleaning your appliance, 10  
Cleaning the detergent dispenser, 10  
Caring for your appliance door and drum, 10  
Cleaning the pump, 10  
Checking the water inlet hose, 10  
Troubleshooting, 11  
Service, 12  
Before calling for Assistance, 12  
1
 
Connecting the drain hose  
GB  
Connect the drain hose,  
without bending it, to a  
draining duct or a wall  
drain situated between  
65 and 100 cm from  
the floor;  
! Do not use extensions or multiple sockets.  
! The power supply cable must never be bent or  
dangerously compressed.  
65 - 100 cm  
! The power supply cable must only be replaced by  
an authorised serviceman.  
Warning! The company denies all liability if and when  
these norms are not respected.  
alternatively, place it  
over the edge of a  
basin, sink or tub,  
fastening the duct  
supplied to the tap (see  
figure). The free end of  
the hose should not be  
underwater.  
The first wash cycle  
Once the appliance has been installed, and before  
you use it for the first time, run a wash cycle with  
detergent and no laundry, setting the 90°C  
programme without a pre-wash cycle.  
! We advise against the use of hose extensions; in  
case of absolute need, the extension must have the  
same diameter as the original hose and must not  
exceed 150 cm in length.  
Technical details  
Model  
WIXE 127  
Electric connection  
59.5 cm wide  
85 cm high  
Before plugging the appliance into the mains  
socket, make sure that:  
Dimensions  
Capacity  
56.5 cm deep  
• the socket is earthed and in compliance with the  
applicable law;  
from 1 to 6 kg  
Electric  
voltage 230/240 Volts 50 Hz  
• the socket is able to sustain the appliance's  
maximum power load indicated in the Technical  
details table (on the right);  
connections  
maximum absorbed power 1850 W  
maximum pressure 1 MPa (10 bar)  
minimum pressure 0.05 MPa (0.5 bar)  
drum capacity 52 litres  
Water  
connections  
• the supply voltage is included within the values i  
ndicated on the Technical details table  
(on the right);  
Spin speed  
up to 1200 rpm  
Control  
programmes  
according to  
IEC456 directive  
programme 2; temperature 60°C;  
run with a load of 6 kg.  
• the socket is compatible with the washing  
machine's plug. If this is not the case, replace  
the socket or the plug.  
This appliance is compliant with the  
following European Community  
Directives:  
! The washing machine should not be installed in an  
outdoor environment, not even when the area is  
sheltered, because it may be very dangerous to  
leave it exposed to rain and thunderstorms.  
- 73/23/CEE of 19/02/73 (Low  
Voltage) and subsequent amendments  
- 89/336/CEE of 03/05/89  
(Electromagnetic Compatibility) and  
subsequent amendments  
- 2002/96/CE  
! When the washing machine is installed, the mains  
socket must be within easy reach.  
3
 
Washing machine description  
Control panel  
FUNCTION  
Buttons  
GB  
START/RESET  
button  
START/STOP  
button  
Display  
Control knob  
Detergent dispenser  
TEMPERATURE  
button  
SPIN  
button  
DELAY TIMER  
button  
Detergent dispenser to add detergent and fabric  
softener (see page 8).  
FUNCTION buttons: to select the functions  
available. The button corresponding to the function  
selected will remain on.  
SPIN button to adjust the spin speed or exclude it  
altogether (see page 7).  
START/RESET button to start the programmes or  
cancel any incorrect settings.  
DELAY TIMER button to delay the start of the set  
programme for a maximum period of 24 hours  
(see page 7).  
START/STOP button to turn the washing machine  
on and off.  
TEMPERATURE button to adjust the wash tempe-  
rature (see page 7).  
Control knob to select the wash programmes.  
The knob stays still during the cycle.  
Display to programme the washing machine and  
follow the wash cycle progress (see opposite page).  
4
 
Display  
GB  
In addition to being a practical tool to programme your appliance (see page 7), the display provides useful  
information concerning the wash cycle.  
Once you have pressed the START/RESET button to  
start the programme, the display will indicate the  
amount of time left until the end of the wash cycle. If  
a delayed start has been set (using the Delay Timer,  
see page 7), the delay time will be indicated on the  
display.  
Door lock:  
If the symbol is on, the washing machine door is locked to prevent it from being opened accidentally. To avoid  
any damages, wait for the symbol to switch itself off before you open the appliance door.  
At the end of the programme, the word END is displayed.  
! In the event of an anomaly, an error code will appear, such as: F-01, see page 11 “Toubleshooting”.  
"MEMO" Programme  
This programme allows you to store your favourite or most-used wash cycle.  
All you have to do is set the desired programme and, once it has started, turn the KNOB to position  
wash cycle will be stored automatically and the word MEMO appears on the display, flashing for a few seconds.  
Subsequently, you can start the "MEMO" cycle by simply turning the KNOB to position ; you will be able to see  
; the  
the temperature/spin cycle/delay timer values by pressing the corresponding buttons; you will also be able to  
modify them but this variation will only be valid for the programme in progress and it will not be stored in the  
"MEMO" cycle.  
If you want to store a new wash cycle, repeat the above-mentioned operations.  
5
 
Starting and Programmes  
5. Add the detergent and any fabric softener  
(see page 8).  
6. Start he programme by pressing the START/RESET  
button.  
To cancel it, keep the START/RESET button  
pressed for at least 2 seconds.  
7. When the programme has ended, the word END is  
displayed. Take out your laundry and leave the  
appliance door ajar to allow the drum to dry  
thoroughly.  
Briefly: starting a programme  
GB  
1. Turn the washing machine on by pressing button  
2. Load your laundry into the washing machine and  
shut the appliance door.  
3. Set the knob to the desired programme. The  
estimated duration of the selected programme is  
displayed. The temperature and spin speed are  
automatically set according to the programme  
(to change them, see page 7).  
.
4. Select any functions (see page 7).  
8. Turn the washing machine off by pressing button  
.
Programme table  
Cycle  
length  
(minutes)  
Detergent  
Type of fabric and  
degree of soil  
Te m p e -  
rature  
Fabric Stain removal  
softener option/bleach  
Programmes  
Description of wash cycle  
pre-  
wash  
wash  
Standard  
Cotton: Extremely soiled whites  
(sheets, tablecloths, etc.)  
Pre-wash, wash cycle, rinse cycles,  
intermediate and final spin cycles  
1
2
2
2
90°C  
90°C  
60°C  
40°C  
135  
125  
110  
105  
Cotton: Extremely soiled whites  
(sheets, tablecloths, etc.)  
Delicate/  
Traditional  
Wash cycle, rinse cycles,  
intermediate and final spin cycles  
Cotton: Heavily soiled whites  
and fast colours  
Delicate/  
Traditional  
Wash cycle, rinse cycles,  
intermediate and final spin cycles  
Cotton: Heavily soiled whites  
and delicate colours  
Delicate/  
Traditional  
Wash cycle, rinse cycles,  
intermediate and final spin cycles  
Cotton: Slightly soiled whites  
and delicate colours (shirts,  
jumpers, etc.)  
Delicate/  
Traditional  
Wash cycle, rinse cycles,  
intermediate and final spin cycles  
3
40°C  
70  
Synthetics: Heavily soiled fast  
colours (baby linen, etc.)  
Wash cycle, rinse cycles, anti-  
crease or delicate spin cycle  
4
4
5
6
60°C  
40°C  
40°C  
30°C  
75  
60  
50  
45  
Delicate  
Delicate  
Synthetics: Heavily soiled fast  
colours (baby linen, etc.)  
Wash cycle, rinse cycles, anti-  
crease or delicate spin cycle  
Wash cycle, rinse cycles, anti-  
crease and delicate spin cycle  
Wool  
Wash cycle, rinse cycles, anti-  
crease or draining cycle  
Very delicate fabrics  
(curtains, silk, viscose, etc.)  
Time 4 you  
Cotton: Heavily soiled whites  
and fast colours  
Wash cycle, rinse cycles,  
intermediate and final spin cycles  
7
8
60  
50  
60°C  
40°C  
Cotton: Slightly soiled whites  
and delicate colours (shirts,  
jumpers, etc.)  
Wash cycle, rinse cycles,  
intermediate and final spin cycles  
Synthetics: Delicate colours (all  
types of slightly soiled  
garments)  
Wash cycle, rinse cycles,  
delicate spin cycle  
9
40°C  
30°C  
40  
30  
Wash cycle, rinse cycles and  
delicate spin cycle  
Delicate colours (all types of  
slightly soiled garments)  
10  
Sport  
Cold wash (without detergents),  
wash cycle, rinse cycles, and  
delicate spin cycle  
11  
12  
30°C  
30°C  
Sports shoes (MAX. 2 pairs)  
50  
60  
Fabrics for sportswear  
(Tracksuits, shorts, etc.)  
Wash cycle, rinse cycles,  
intermediate and final spin cycles  
(see page 5).  
MEMO  
Allows for any wash cycle to be stored  
PARTIAL PROGRAMMES  
Delicate/  
Traditional  
Rinse  
Rinse cycles and spin cycle  
Spin  
Draining and spin cycle  
Draining  
Drain  
Notes  
-For programmes 7 and 8, we advise against exceeding a wash load of 3.5 kg.  
-For programme 12 we advise against exceeding a wash load of 2 kg.  
-For the anti-crease function: see Easy iron, opposite page. The information contained in the table is purely indicative.  
Special programme  
Daily (programme 10 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only lasts  
30 minutes and allows you to save on both time and energy. By setting this programme (10 at 30°C), you can wash  
different fabrics together (except for woollen and silk items), with a maximum load of 3 kg.  
We recommend the use of liquid detergent.  
6
 
Personalisations  
Setting the spin cycle  
If, when the appliance is switched on, the KNOB is positioned on  
a programme with a spin cycle, a fixed appears. Press button  
and the maximum spin speed allowed for the programme set  
will be displayed, and the icon flashes. Press it again and the  
GB  
values lower until they reach OFF, which indicates that the spin  
cycle has been excluded (press it again to go back to the  
maximum value); stop on the desired speed, after approximately  
2 seconds the setting is accepted: the symbol  
remains fixed.  
The spin cycle setting is enabled with all the programmes except  
for 6 and the Draining cycle.  
Setting the Delay Timer  
Press the button and you will see the word OFF on the  
display, while the relative symbol flashes.  
Press the button again and "1h" appears, that is, a delay of one  
hour (this can reach up to 24h); stop on the "desired" delay; after  
approximately 2 seconds the setting is accepted, following which,  
the time for the set programme appears on the display and the  
symbol  
remains on.  
If you now press the START/RESET button, the set "delay"  
appears; this decreases every hour until the start of the cycle. In this phase, the "delay" can only be modified by  
decreasing it.  
The Delay Timer regulation is enabled with all programmes.  
Setting the temperature  
If, when the appliance is switched on, the KNOB is positioned on a programme for which the temperature needs  
to be regulated, a fixed  
set will be displayed and the  
indicates a cold wash cycle (press it again to go back to the maximum value); stop on the desired value, after  
appears. Press button  
and the maximum temperature allowed for the programme  
icon flashes. Press it again and the temperature lowers until it reaches OFF, which  
approximately 2 seconds the setting is accepted: the symbol  
The temperature adjustment is enabled with all wash programmes.  
remains fixed.  
Functions  
To enable a function:  
1. press the button corresponding to the desired function, according to the table below;  
2. the function is enabled when the corresponding button is illuminated.  
Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the  
programme set.  
If you set a function that is incompatible with another function you selected previously, only the last one selected  
will be enabled.  
Enabled with  
programmes:  
Function  
Effect  
Comments  
Bleaching cycle  
designed to  
remove the  
Please remember to pour the bleach into extra compartment 4  
(see page 8).  
This function is incompatible with the EASY IRON function.  
2, 3, 4,  
Rinse cycle.  
Stain  
removal  
toughest stains.  
1, 2, 3, 4, 7,  
8, 9, 11, 12,  
Rinse cycle.  
Increases the  
efficiency of the  
rinse.  
Recommended when the appliance has a full load or with large  
quantities of detergent.  
Extra Rinse  
This option  
reduces the  
amount of  
creasing on  
fabrics, making  
them easier to  
iron.  
When this function is set, programmes 4, 5, 6 will end, with the  
laundry left to soak (Anti-crease), and the relative button flashes:  
- to conclude the cycle, press the START/RESET button or the  
EASY IRON button;  
- to run the draining cycle alone, set the knob to the relative  
symbol and press the START/RESET button.  
This function is incompatible with the STAIN REMOVAL function.  
3, 4, 5, 6, 7, 8,  
9, Rinse  
cycle.  
Easy iron  
7
 
Detergents and laundry  
Detergent dispenser  
Preparing your laundry  
GB  
Good washing results also depend on the correct  
dose of detergent: adding too much detergent won't  
necessarily make for a more efficient wash, and may  
in fact cause build up on the interior of your  
• Divide your laundry according to:  
- the type of fabric/the symbol on the label.  
- the colours: separate coloured garments from  
whites.  
appliance and even pollute the environment.  
• Empty all pockets and check for loose buttons.  
• Do not exceed the weight limits stated below,  
which refer to the weight when dry:  
Sturdy fabrics: max 6 kg  
Open up the detergent  
4
dispenser and pour in  
the detergent and fabric  
Synthetic fabrics: max 2.5 kg  
softener, as follows.  
Delicate fabrics: max 2 kg  
3
Wool: max 1,5 kg  
2
1
How much does your laundry weigh?  
1 sheet 400-500 g  
1 pillow case 150-200 g  
1 tablecloth 400-500 g  
1 bathrobe 900-1,200 g  
1 towel 150-250 g  
compartment 1: Detergent for pre-wash  
(powder)  
Before pouring in the detergent, make sure that  
extra compartment 4 has been removed.  
compartment 2: Detergent for the wash cycle  
(powder or liquid)  
Special items  
Curtains: fold curtains and place them in a pillow  
case or mesh bag. Wash them separately without  
exceeding half the appliance load. Use programme 6  
which excludes the spin cycle automatically.  
Liquid detergent should only be poured in  
immediately prior to the wash cycle start.  
compartment 3: Additives (fabric softeners, etc.)  
The fabric softener should not overflow from the grid.  
extra compartment 4: Bleach  
Quilted coats and windbreakers: if they are  
padded with goose or duck down, they can be  
machine-washed. Turn the garments inside out and  
load a maximum of 2-3 kg, repeating the rinse cycle  
once or twice and using the delicate spin cycle.  
! Do not use hand wash detergent because it may  
form too much foam.  
Bleach cycle  
! Traditional bleach should be used on sturdy  
white fabrics, and delicate bleach for coloured  
fabrics, synthetics and for wool.  
Wool: for best results, use a specific detergent,  
taking care not to exceed a load of 1,5 kg.  
Place extra  
compartment 4,  
provided, into  
compartment 1.  
When pouring in the  
bleach, be careful not to  
exceed the "max" level  
indicated on the central  
pivot (see figure).  
To run the bleach cycle alone, pour the bleach into extra  
compartment 4, set the Rinse programme  
and  
enable the Stain removal function (see page 7).  
To bleach during a wash cycle, pour in the detergent  
and fabric softener, set the desired programme and  
enable the Stain removal function (see page 7).  
The use of extra compartment 4 excludes the  
possibility of using the pre-wash cycle.  
8
 
Precautions and advice  
! The washing machine was designed and built in  
compliance with the applicable international safety  
regulations. The following information is provided for  
your safety and should consequently be read  
carefully.  
The crossed out "wheeled bin" symbol on the  
product reminds you of your obligation, that when  
you dispose of the appliance it must be separately  
collected.  
Consumers should contact their local authority or  
retailer for information concerning the correct  
disposal of their old appliance.  
GB  
General safety  
• This appliance has been designed for non-  
professional, household use and its functions must  
not be changed.  
• Disposing of an old washing machine:  
before scrapping your appliance, cut the power  
supply cable and remove the appliance door.  
• This washing machine should only be used by  
adults and in accordance with the instructions  
provided in this manual.  
Saving energy and respecting the  
environment  
Environmentally-friendly technology  
• Never touch the washing machine when barefoot  
or with wet or damp hands or feet.  
If you only see a little water through your appliance  
door, this is because thanks to the latest technology,  
your washing machine only needs less than half the  
amount of water to get the best results: an objective  
reached to respect the environment.  
• Do not pull on the power supply cable to unplug  
the appliance from the electricity socket. Pull the  
plug out yourself.  
Saving on detergent, water,  
energy and time  
• Do not open the detergent dispenser while the  
appliance is in operation.  
• To avoid wasting resources, the washing machine  
should be used with a full load. A full load instead  
of two half loads allows you to save up to 50% on  
energy.  
• Do not touch the drain water as it could reach  
very high temperatures.  
• Never force the washing machine door: this could  
damage the safety lock mechanism designed to  
prevent any accidental openings.  
• The pre-wash cycle is only necessary on  
extremely soiled garments. Avoiding it will save on  
detergent, time, water and between 5 and 15%  
energy.  
• In the event of a malfunction, do not under any  
circumstances touch internal parts in order to  
attempt repairs.  
• Treating stains with a stain remover or leaving  
them to soak before washing will cut down the  
need to wash them at high temperatures. A  
programme at 60°C instead of 90°C or one at  
40°C instead of 60°C will save up to 50% on  
energy.  
• Always keep children well away from the  
appliance while in operation.  
• The appliance door tends to get quite hot during  
the wash cycle.  
• Use the correct quantity of detergent depending  
on the water hardness, how soiled the garments  
are and the amount of laundry you have, to avoid  
wastage and to protect the environment: despite  
being biodegradable, detergents do contain  
ingredients that alter the natural balance of the  
environment. In addition, avoid using fabric  
softener as much as possible.  
• Should it have to be moved, proceed with the  
help of two or three people and handle it with the  
utmost care. Never try to do this alone, because  
the appliance is very heavy.  
• Before loading your laundry into the washing  
machine, make sure the drum is empty.  
• If you use your washing machine from late in the  
afternoon until the early hours of the morning, you  
will help reduce the electricity board's peak load.  
The Delay Timer option (see page 7) helps to  
organise your wash cycles accordingly.  
Disposal  
• Disposal of old electrical appliances  
The European Directive 2002/96/EC on Waste  
Electrical and Electronic Equipment (WEEE), requires  
that old household electrical appliances must not be  
disposed of in the normal unsorted municipal waste  
stream. Old appliances must be collected separately  
in order to optimise the recovery and recycling of the  
materials they contain and reduce the impact on  
human health and the environment.  
• If your laundry has to be dried in a tumble dryer,  
select a high spin speed. Having the least water  
possible in your laundry will save you time and  
energy in the drying process.  
9
 
Care and maintenance  
Cutting off the water or electricity  
supply  
Cleaning the pump  
GB  
The washing machine is fitted with a self-cleaning  
pump that does not require any maintenance.  
Sometimes, small items (such as coins or buttons)  
may fall into the pre-chamber that protects the  
pump, situated in the lower part of the same.  
Turn off the water tap after every wash. This will  
limit the wear of your appliance's water system  
and also prevent leaks.  
Unplug your appliance when cleaning it and  
during all maintenance operations.  
! Make sure the wash cycle has ended and unplug  
the appliance.  
Cleaning your appliance  
To access the pre-chamber:  
The exterior and rubber parts of your appliance can  
be cleaned with a soft cloth soaked in lukewarm  
soapy water. Do not use solvents or abrasives.  
1. using a screwdriver,  
remove the cover panel  
on the lower front of the  
washing machine (see  
figure);  
Cleaning the detergent dispenser  
Remove the dispenser  
by pulling it out (see  
figure).  
Wash it under running  
water; this operation  
should be repeated  
frequently.  
2. unscrew the lid  
rotating it anti-  
clockwise (see figure): a  
little water may trickle  
out. This is perfectly  
normal;  
Caring for your appliance door and  
drum  
Always leave the appliance door ajar to prevent  
unpleasant odours from forming.  
3. clean the interior thoroughly;  
4. screw the lid back on;  
5. reposition the panel, making sure the hooks are  
securely in place before you push it onto the  
appliance.  
Checking the water inlet hose  
Check the water inlet hose at least once a year. If  
you see any cracks, replace it immediately: during  
the wash cycles, water pressure is very strong and  
a cracked hose could easily split open.  
! Never use hoses that have already been used.  
10  
 
Troubleshooting  
Your washing machine could fail to work. Before calling for Assistance (see page 12), make sure the problem  
can't easily be solved by consulting the following list.  
GB  
Possible causes/Solution:  
Problem  
• The appliance is not plugged into the socket, or not enough to  
make contact.  
• There has been a power failure.  
The washing machine won't  
start.  
• The appliance door is not shut properly (the word DOOR is  
displayed).  
The wash cycle won't start.  
• The  
button has not been pressed.  
• The START/RESET button has not been pressed.  
• The water tap is not turned on.  
• A delayed start has been set (using the Delay Timer, see page 7).  
The washing machine fails to  
load water (The wording H2O is  
displayed).  
• The water inlet hose is not connected to the tap.  
• The hose is bent.  
• The water tap is not turned on.  
• There is a water shortage.  
• The water pressure is insufficient.  
• The START/RESET button has not been pressed.  
• The drain hose is not fitted between 65 and 100 cm from the floor  
(see page 3).  
• The free end of the hose is underwater (see page 3).  
• The wall drainage system doesn't have a breather pipe.  
The washing machine  
continuously loads and unloads  
water.  
If the problem persists even after these checks, turn off the water tap,  
switch the appliance off and call for Assistance. If the dwelling is on one of  
the upper floors of a building, there may be drain trap problems causing the  
washing machine to load and unload water continuously. In order to avoid  
such an inconvenience, special anti-drain trap valves are available in shops.  
• The programme does not foresee the draining: some programmes  
require enabling the draining manually (see page 6).  
• The Easy iron option is enabled: to complete the programme, press  
the START/RESET button (see page 7).  
The washing machine does not  
drain or spin.  
• The drain hose is bent (see page 3).  
• The drain duct is clogged.  
• When the machine is installed, the locking screws for the oscillating  
assembly are still in place. Remove the screws (see page 2).  
• The washing machine is not level (see page 2).  
• The washing machine is closed in between furniture cabinets and  
the wall (see page 2).  
The washing machine vibrates  
too much during the spin cycle.  
• The water inlet hose is not screwed on correctly (see page 2).  
• The detergent dispenser is obstructed (to clean it, see page 10).  
• The drain hose is not secured properly (see page 3).  
The washing machine leaks.  
The machine is blocked and the  
display shows an anomaly error  
code (i.e. F-01).  
• This means there is a problem with the machine. Before calling  
Assistance, please follow the set of instructions below:  
1. Switch off the machine.  
2. Remove the plug connecting the appliance to the mains supply and  
wait for at least 40 seconds.  
3. Place the plug back into the socket.  
4. Switch on the machine.  
5. If the problem is still evident after this process has been carried out,  
contact Assistance.all for Assistance because this means there is an  
abnormality.  
• The detergent is not suitable for machine washing (it should bear  
the definition "for washing machines" or "hand and machine wash",  
or the like).  
There is too much foam.  
• You used too much detergent.  
11  
 
Service  
195053270.00  
-
07/2005  
Xerox Business Services  
Before calling for Assistance:  
GB  
Check whether you can solve the problem on your own (see page 11);  
Restart the programme to check whether the problem has been solved;  
If this is not the case, contact an authorised Technical Service Centre on the telephone number  
provided on the guarantee certificate.  
.
! If the machine has been installed or used incorrectly, you may be charged for the maintenance callout  
service  
! Always request the assistance of authorised servicemen.  
Notify the operator of:  
• the type of problem;  
• the appliance model (Mod.);  
• the serial number (S/N).  
This information can be found on the data plate situated on the rear of the washing machine.  
12  
 

Indesit Dishwasher DFG 262 User Manual
Init Portable Media Storage PR MS10265 User Manual
Intel Server S5400SF User Manual
Jenn Air Cooktop CCG456 User Manual
Jenn Air Ventilation Hood JXT5830ADB User Manual
JVC CD Player RV DP200BK User Manual
JVC DVD Player KD DV5307 User Manual
JVC DVD Player TH C30 User Manual
Kelvinator Home Security System KCG130GW0 User Manual
Kenwood Stereo Amplifier KAC X522 User Manual