Indesit Washer IWC 71451 User Manual

Instructions for use  
WASHING MACHINE  
Contents  
GB  
Installation, 2-3-4-5  
Unpacking and levelling  
Connecting the electricity and water supplies  
The first wash cycle  
GB  
English,1  
Technical data  
Care and maintenance, 6  
Cutting off the water or electricity supply  
Cleaning the washing machine  
Cleaning the detergent dispenser drawer  
Caring for the door and drum of your appliance  
Cleaning the pump  
Checking the water inlet hose  
Precautions and tips, 7  
General safety  
Disposal  
Description of the washing machine  
and starting a wash cycle, 8-9  
Control panel  
IWC 71451  
Indicator lights  
Starting a wash cycle  
Wash cycles, 10  
Table of wash cycles  
Personalisation, 11  
Setting the temperature  
Setting the spin speed  
Functions  
Detergents and laundry, 12  
Detergent dispenser drawer  
Preparing the laundry  
Garments requiring special care  
Load balancing system  
Troubleshooting, 13-14  
Assistance, 15-16  
1
 
Connecting the drain hose  
Connect the drain  
• the supply voltage is included within the values  
indicated on the Technical Data Plate fixed on  
the machine.  
GB  
hose, without bending  
it, to a draining duct or  
a wall drain situated  
between 65 and 100  
cm from the floor;  
• the socket is compatible with the washing  
machine’s plug. If this is not the case, replace  
the socket or the plug.  
65 - 100 cm  
Your appliance is now supplied with a 13 amp fu-  
sed plug it can be plugged into a 13 amp socket  
for immediate use. Before using the appliance  
please read the instructions below.  
The drain hose may  
be connected to an  
under-sink trap. Be-  
fore connecting the  
drain hose from the  
machine ensure that  
any blanks or remo-  
vable ends have been  
taken off the spigot.  
WARNING-THISAPPLIANCEMUSTBEEARTHED.  
THE FOLLOWING OPERATIONS SHOULD BE  
CARRIED OUT BY A QUALIFIED ELECTRICIAN.  
Replacing the fuse:  
When replacing a faulty fuse, a 13 amp ASTA  
approved fuse to BS 1362 should always be  
used, and the fuse cover re-fitted. If the fuse  
cover is lost, the plug must not be used until a  
replacement is obtained.  
Where it connects to  
the waste water pipe  
cut end off spigot or  
remove the blanking cap  
Replacement fuse covers:  
If it is placed over the  
edge of a basin or sink  
be sure the free end of  
the hose should not  
be underwater.  
If a replacement fuse cover is fitted, it must be of  
the correct colour as indicated by the coloured  
marking or the colour that is embossed in words  
on the base of the plug. Replacements can be  
obtaineddirectlyfromyournearestServiceDepot.  
Removing the plug:  
If your appliance has a non-rewireable moulded  
plug and you should wish to re-route the mains  
cable through partitions, units etc., please en-  
sure that either:  
! We advise against the use of hose extensions; in  
caseofabsoluteneed,theextensionmusthavethe  
same diameter as the original hose and must not  
exceed 150 cm in length. Ensure that if the drain  
hose is pushed into a standpipe, that the end does  
notgodownmorethan15cms(6inches).Ifthehose  
ispusheddowntoofar,thismaycausethemachine  
to self -syphon ie. continuously empty as it is filling.  
the plug is replaced by a fused 13 ampere rewi-  
reable plug bearing the BSI mark of approval.  
or:  
the mains cable is wired directly into a 13 amp  
cable outlet, controlled by a switch, (in complian-  
ce with BS 5733) which is accessible without  
moving the appliance.  
Disposing of the plug:  
Electric connection  
Ensure that before disposing of the plug itself,  
you make the pins unusable so that it cannot be  
accidentally inserted into a socket.  
Before plugging the appliance into the mains  
socket, make sure that:  
Instructions for connecting cable to an alterna-  
tive plug:  
• the socket is earthed and in compliance with  
the applicable law;  
Important: the wires in the mains lead are co-  
loured in accordance with the following code:  
Green & Yellow Earth  
• the socket is able to sustain the appliance’s  
maximum power load indicated on the Technical  
Data Plate fixed on the machine;  
Blue  
Brown  
Neutral  
Live  
3
 
As the colours of the wires in the lead may not  
correspond with the coloured markings iden-  
tifying the terminals in your plug, proceed as  
follows:  
! The power supply cable must only be repla-  
GB  
ced by an authorised serviceman.  
Warning! The company denies all liability if and  
when these norms are not respected.  
Connect Green & Yellow wire to terminal  
marked E or or coloured Green or Green &  
Yellow.  
The first wash cycle  
Connect Brown wire to terminal marked L or  
coloured Red.  
Connect Blue wire to terminal marked N or co-  
loured Black.  
Once the appliance has been installed, and  
before you use it for the first time, run a wash  
cycle with detergent and no laundry, setting the  
90°C programme.  
If a 13 amp plug (BS 1363) is used it must be  
fitted with a 13 amp fuse, either in the plug or  
adaptor or at the distribution board.  
If you are in any doubt regarding the electrical  
supply to your machine, consult a qualified  
electrician before use.  
How to connect an alternative plug:  
The wires in this mains lead are coloured in  
accordance with the following code:  
BLUE  
NEUTRAL (N)  
LIVE (L)  
EARTH (E)  
BROWN  
GREEN & YELLOW  
GREEN &  
YELLOW  
13 ampere fuse  
BROWN  
CROSS-BAR  
CORD GRIP  
BLUE  
Disposing of the appliance:  
When disposing of the appliance please re-  
move the plug by cutting the mains cable as  
close as possible to the plug body and dispo-  
se of it as described above.  
! The washing machine should not be installed  
in an outdoor environment, not even where  
the area is sheltered, because it may be very  
dangerous to leave it exposed to damp, rain  
and thunderstorms.  
! When the washing machine is installed, the  
mains socket must be within easy reach.  
! Do not use extensions or multiple sockets.  
! The power supply cable must never be bent  
or dangerously compressed.  
4
 
GB  
Technical data  
Model  
IWC 71451  
width 59.5 cm  
height 85 cm  
depth 53,5 cm  
Dimensions  
Capacity  
from 1 to 7 kg  
Electrical  
connections  
please refer to the technical  
data plate fixed to the machine  
maximum pressure  
1 MPa (10 bar)  
Water  
connection  
minimum pressure  
0.05 MPa (0.5 bar)  
drum capacity 52 litres  
up to 1400 rotations per  
minute  
Spin speed  
Test wash  
Programme 2:  
Cotton Standard 60°.  
Programme 3:  
cycles in  
accordance  
with directives  
1061/2010 and  
1015/2010.  
Cotton Standard 40°.  
This appliance conforms to  
the following EC Directives:  
- 2004/108/EC (Electroma-  
gnetic  
Compatibility)  
- 2012/19/EU  
- 2006/95/EC Low Voltage)  
5
 
Care and maintenance  
2. unscrew the lid  
by rotating it anti-  
clockwise (see figu-  
re): a little water may  
trickle out. This is  
perfectly normal;  
Cutting off the water and electri-  
city supplies  
GB  
Turn off the water tap after every wash cycle.  
This will limit wear on the hydraulic system  
inside the washing machine and help to pre-  
vent leaks.  
• Unplug the washing machine when cleaning  
it and during all maintenance work.  
Cleaning the washing machine  
The outer parts and rubber components of the  
3. clean the inside thoroughly;  
4. screw the lid back on;  
5. reposition the panel, making sure the hooks  
are securely in place before you push it onto  
the appliance.  
appliance can be cleaned using a soft cloth  
soaked in lukewarm soapy water. Do not use  
solvents or abrasives.  
Cleaning the detergent dispenser  
drawer  
Checking the water inlet hose  
Remove the dispenser  
by raising it and pul-  
ling it out (see figure).  
Wash it under running  
water; this operation  
should be repeated  
frequently.  
Check the inlet hose at least once a year. If  
there are any cracks, it should be replaced  
immediately: during the wash cycles, water  
pressure is very strong and a cracked hose  
could easily split open.  
! Never use second-hand hoses.  
Caring for the door and drum of  
your appliance  
• Always leave the porthole door ajar in order  
to prevent unpleasant odours from forming.  
Cleaning the pump  
The washing machine is fitted with a self-cle-  
aning pump which does not require any main-  
tenance. Sometimes, small items (such as  
coins or buttons) may fall into the pre-chamber  
which protects the pump, situated in its bot-  
tom part.  
! Make sure the wash cycle has finished and  
unplug the appliance.  
To access the pre-  
chamber:  
1. using a screwdri-  
ver, remove the cover  
panel on the lower  
front part of the wa-  
shing machine (see  
figure);  
6
 
Precautions and tips  
product reminds you of your obligation, that when you  
! This washing machine was designed and constructed in  
accordance with international safety regulations. The fol-  
lowing information is provided for safety reasons and must  
therefore be read carefully.  
GB  
dispose of the appliance it must be separately collected.  
Consumers should contact their local authority or retailer  
for information concerning the correct disposal of their  
old appliance.  
General safety  
• This appliance was designed for domestic use only.  
This appliance can be used by children aged  
from 8 years and above and persons with re-  
duced physical, sensory or mental capabilities  
or lack of experience and knowledge if they  
have been given supervision or instruction  
concerning use of the appliance in a safe way  
and understand the hazards involved. Chil-  
dren shall not play with the appliance. Clea-  
ning and user maintenance shall not be made  
by children without supervision.  
• Do not touch the machine when barefoot or with wet or  
damp hands or feet.  
• Do not pull on the power supply cable when unplugging  
the appliance from the electricity socket. Hold the plug  
and pull.  
• Do not open the detergent dispenser drawer while the  
machine is in operation.  
• Do not touch the drained water as it may reach extreme-  
ly high temperatures.  
• Never force the porthole door. This could damage the  
safety lock mechanism designed to prevent accidental  
opening.  
• If the appliance breaks down, do not under any circum-  
stances access the internal mechanisms in an attempt  
to repair it yourself.  
• Always keep children well away from the appliance while  
it is operating.  
• The door can become quite hot during the wash cycle.  
• If the appliance has to be moved, work in a group of two  
or three people and handle it with the utmost care. Never  
try to do this alone, because the appliance is very heavy.  
• Before loading laundry into the washing machine, make  
sure the drum is empty.  
Disposal  
• Disposing of the packaging materials: observe local  
regulations so that the packaging may be re-used.  
• The European Directive 2012/19/EU on Waste Electrical  
and Electronic Equipment, requires that old household  
electrical appliances must not be disposed of in the  
normal unsorted municipal waste stream. Old applian-  
ces must be collected separately in order to optimise  
the recovery and recycling of the materials they contain  
and reduce the impact on human health and the envi-  
ronment. The crossed out “wheeled bin” symbol on the  
7
 
Description of the washing  
machine and starting a wash cycle  
Control panel  
GB  
WASH CYCLE PROGRESS/  
DELAY TIMER indicator lights  
FUNCTION  
START/PAUSE  
ON/OFF button  
buttons with  
button with  
indicator lights  
indicator light  
TEMPERATURE  
DOOR LOCKED  
knob  
indicator light  
Detergent dispenser drawer  
WASH CYCLE  
SPIN SPEED  
knob  
knob  
Detergent dispenser drawer: used to dispense  
detergents and washing additives (see “Detergents and  
laundry”).  
DOOR LOCKED indicator light: indicates whether the  
door may be opened or not (see next page).  
START/PAUSE button with indicator light: starts or tem-  
porarily interrupts the wash cycles.  
ON/OFF button: switches the washing machine on and off.  
N.B. To pause the wash cycle in progress, press this  
button; the corresponding indicator light will flash orange,  
while the indicator light for the current wash cycle phase  
will remain lit in a fixed manner. If the DOOR LOCKED  
indicator light is switched off, the door may be opened  
(wait approximately 3 minutes).  
WASH CYCLE knob: programmes the wash cycles. Du-  
ring the wash cycle, the knob does not move.  
FUNCTION buttons with indicator light: used to select the  
available functions. The indicator light corresponding to the  
selected function will remain lit.  
To start the wash cycle from the point at which it was inter-  
rupted, press this button again.  
TEMPERATURE knob: sets the temperature or the cold  
wash cycle (see “Personalisation”).  
Standby mode  
This washing machine, in compliance with new energy sa-  
ving regulations, is fitted with an automatic standby system  
which is enabled after about 30 minutes if no activity is  
detected. Press the ON-OFF button briefly and wait for the  
machine to start up again.  
SPIN SPEED knob: sets the spin speed or exclude the  
spin cycle completely (see “Personalisation”).  
WASH CYCLE PROGRESS/DELAY TIMER indicator  
lights: used to monitor the progress of the wash cycle.  
The illuminated indicator light shows which phase is in  
progress.  
Consumption in off-mode: 0,5 W  
Consumption in Left-on: 8 W  
If the Delay Timer function has been set, the time remai-  
ning until the wash cycle starts will be indicated (see next  
page).  
8
 
Wash cycle phase indicator lights  
Indicator lights  
GB  
Once the desired wash cycle has been selected and has be-  
gun, the indicator lights switch on one by one to indicate which  
phase of the cycle is currently in progress.  
The indicator lights provide important information.  
This is what they can tell you:  
Wash  
Rinse  
Delayed start  
If the DELAY TIMER function has been activated (see “Per-  
sonalisation”), after the wash cycle has been started the  
indicator light corresponding to the selected delay period  
will begin to flash:  
Spin  
Drain  
End of wash cycle  
Function buttons and corresponding indicator lights  
When a function is selected, the corresponding indicator  
light will illuminate.  
If the selected function is not compatible with the program-  
med wash cycle, the corresponding indicator light will flash  
and the function will not be activated.  
If the selected function is not compatible with another  
function which has been selected previously, the indicator  
light corresponding to the first function selected will  
flash and only the second function will be activated; the  
indicator light corresponding to the enabled option will  
remain lit.  
As time passes, the remaining delay will be displayed and  
the corresponding indicator light will flash:  
Door locked indicator light  
When the indicator light is on, the porthole door is locked  
to prevent it from being opened; make sure the indicator  
light is off before opening the door (wait approximately 3  
minutes). To open the door during a running wash cycle,  
press the START/PAUSE button; the door may be opened  
once the DOOR LOCKED indicator light turns off.  
The set programme will start once the selected time delay  
has expired.  
Starting a wash cycle  
1. Switch the washing machine on by pressing the ON/OFF button. All indicator lights will switch on for a few seconds, then  
they will switch off and the START/PAUSE indicator light will pulse.  
2. Load the laundry and close the door.  
3. Set the WASH CYCLE knob to the desired programme.  
4. Set the washing temperature (see “Personalisation”).  
5. Set the spin speed (see “Personalisation”).  
6. Measure out the detergent and washing additives (see “Detergents and laundry”).  
7. Select the desired functions.  
8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit in a fixed man-  
ner, in green. To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.  
9. At the end of the wash cycle the  
indicator light will switch on. The door can be opened once the DOOR LOCK indi-  
cator light turns off (wait approximately 3 minutes). Take out your laundry and leave the appliance door ajar to make sure the  
drum dries completely. Switch the washing machine off by pressing the ON/OFF button.  
9
 
Wash cycles  
Table of wash cycles  
GB  
Detergents  
Max.  
Max.  
Description of the wash cycle  
temp. speed  
(°C)  
(rpm)  
Fabric  
Wash  
softener  
Daily  
1
2
3
4
4
5
White Cotton: extremely soiled whites.  
Cotton Standard (1): heavily soiled whites and resistant colours.  
Cotton Standard (2): lightly soiled whites and delicate colours.  
Synthetics: heavily soiled resistant colours.  
Synthetics (3): lightly soiled resistant colours.  
Mix Colored: lightly soiled whites and delicate colours.  
20° Zone  
90°  
60°  
40°  
50°  
40°  
40°  
1400  
1400  
1400  
800  
7
7
53  
53  
53  
-
2.16 72 160’  
1.13 52.5 180’  
1.00 75 170’  
7
3.5  
3.5  
7
-
-
110’  
800  
44  
53  
0.57 46 100’  
0.66 54 90’  
1400  
6
7
8
Cotton Standard: lightly soiled whites and delicate colours.  
Mix Light  
20°  
20°  
20°  
1400  
800  
7
7
-
-
-
-
-
-
-
-
-
170’  
120’  
20’  
20’ Refresh  
800  
1.5  
Special  
9
Outwear  
30°  
40°  
40°  
400  
800  
800  
-
2
-
-
-
-
-
-
-
-
-
60’  
70’  
75’  
10 Wool: for wool. cashmere. etc.  
11 Jeans  
1.5  
3.5  
Sport  
12 Sport Intensive  
13 Sport Light  
30°  
30°  
600  
600  
2.5  
2.5  
-
-
-
-
-
-
85’  
60’  
Max. 2  
pairs  
14 Special Shoes  
30°  
600  
-
-
-
60’  
Partial wash cycles  
Rinse  
-
-
1400  
1400  
-
-
7
7
-
-
-
-
-
-
36’  
16’  
Spin + Drain  
-
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual  
duration can vary according to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inser-  
ted, load balancing and any wash options selected.  
1) Test wash cycle in compliance with directive 1061/2010: set wash cycle 2 with a temperature of 60°C.  
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be  
used for garments which can be washed at 60°C. The actual washing temperature may differ from the indicated value.  
2) Test wash cycle in compliance with directive 1061/2010: set wash cycle 3 with a temperature of 40°C.  
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be  
used for garments which can be washed at 40°C. The actual washing temperature may differ from the indicated value.  
For all Test Institutes:  
3) Long wash cycle for cottons: set wash cycle 3 with a temperature of 40°C.  
4) Synthetic program along: set wash cycle 4 with a temperature of 40°C.  
10  
 
Personalisation  
Setting the temperature  
Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).  
GB  
The temperature may be lowered, or even set to a cold wash  
.
The washing machine will automatically prevent you from selecting a temperature which is higher than the maximum value  
set for each wash cycle.  
Setting the spin speed  
Turn the SPIN SPEED knob to set the spin speed for the selected wash cycle.  
The maximum spin speeds available for each wash cycle are as follows:  
Wash cycles  
Cottons  
Maximum spin speed  
1400 rpm  
Synthetics  
Wool  
800 rpm  
800 rpm  
The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol  
.
The washing machine will automatically prevent you from selecting a spin speed which is higher than the maximum speed  
set for each wash cycle.  
Functions  
The various wash functions available with this washing machine will help to achieve the desired results, every time.  
To activate the functions:  
1. Press the button corresponding to the desired function;  
2. the function is enabled when the corresponding indicator light is illuminated.  
Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in conjunction with the  
selected wash cycle.  
Selecting this option enables you to suitably adjust drum rotation, temperature and water to a reduced load of lightly soiled  
cotton and synthetic fabrics (refer to the Table of wash cycles”). “  
water and electricity. We suggest using a liquid detergent suitably measured out to the load quantity.  
! This function may not be used in conjunction with wash cycles 1, 6, 7, 8, 9, 10, 11, 12, 13, 14,  
” enables you to wash in less time thereby saving  
,
.
The  
function saves energy by not heating the water used to wash your laundry - an advantage both to the  
environment and to your energy bill. Instead, intensified wash action and water optimisation ensure great wash results in the  
same average time of a standard cycle.  
For the best washing results we recommend the usage of a liquid detergent.  
! This function may not be used in conjunction with wash cycles 6, 7, 8, 10, 12, 13, 14,  
,
.
Extra Rinse  
By selecting this option, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is particularly  
useful for sensitive skin.  
! It cannot be used in conjunction with the 8,  
programmes.  
Delay Timer  
This timer delays the start time of the wash cycle by up to 12 hours.  
Press the button repeatedly until the indicator light corresponding to the desired delay time switches on. The fifth time the button  
is pressed, the function will be disabled.  
N.B. Once the START/PAUSE button has been pressed, the delay time can only be modified by decreasing it until launching  
the set programme.  
! This option is enabled with all programmes.  
11  
 
Detergents and laundry  
necessary; do not use softeners or detergents containing  
softeners. Stuffed duvets cannot be washed with this pro-  
gramme.  
Detergent dispenser drawer  
GB  
Good washing results also depend on the correct dose of  
detergent: adding too much detergent will not necessa-  
rily result in a more efficient wash, and may in fact cause  
build up on the inside of your appliance and contribute to  
environmental pollution.  
Wool: all wool garments can be washed using programme  
10, even those carrying the “hand-wash only”  
label.  
For best results, use special detergents and do not exceed  
1,5 kg of laundry.  
Jeans: Turn garments inside-out before washing and use a  
liquid detergent. Use programme 11.  
Sport Intensive (programma 12): is for washing heavily  
soiled sports clothing fabrics (tracksuits, shorts, etc.); for  
best results, we recommend not exceeding the maximum  
load indicated in the “Programme table”.  
! Do not use hand washing detergents because these  
create too much foam.  
! Use powder detergent for white cotton garments, for pre-  
washing, and for washing at temperatures over 60°C.  
Sport Light (programma 13): is for washing lightly soiled  
sports clothing fabrics (tracksuits, shorts, etc.); for best  
results, we recommend not exceeding the maximum load  
indicated in the “Programme table”. We recommend using  
a liquid detergent and dosage suitable for a half-load.  
Special Shoes (programma 14): is for washing sports  
shoes; for best results, do not wash more than 2 pairs si-  
multaneously.  
! Follow the instructions given on the detergent packaging.  
Open the detergent di-  
spenser drawer and pour  
in the detergent or washing  
additive, as follows.  
3
2
1
The 20° wash cycles (Zone 20°) offer effective washing  
performance at low temperatures, reducing electricity  
usage and expenditure while benefitting the environment.  
The 20° wash cycles meet all requirements:  
Cotton Standard (programme 6) ideal for lightly soiled  
cotton loads. The effective performance levels achieved  
at cold temperatures, which are comparable to washing  
at 40°, are guaranteed by a mechanical action which  
operates at varying speed, with repeated and frequent  
peaks.  
Mix Light (programme 7) ideal for mixed loads (cotton  
and synthetics) with a normal soil level. The effective  
performance levels achieved at cold temperatures are  
guaranteed by a mechanical action which operates at  
varying speed, across set average intervals.  
! Do not pour detergent into the compartment 1.  
Detergent should only be poured into the compartment 2.  
compartment 2: Detergent for the wash cycle  
(powder or liquid)  
Liquid detergent should only be poured in immediately  
prior to the start of the wash cycle.  
compartment 3: Additives (fabric softeners, etc.)  
The fabric softener should not overflow the grid.  
20’ Refresh (programme 8) ideal for refreshing and  
washing lightly soiled garments in a few minutes. It lasts  
just 20 minutes and therefore saves both time and energy.  
It can be used to wash different types of fabrics together  
(except for wool and silk), with a maximum load of 1.5 kg.  
Preparing the laundry  
• Divide the laundry according to:  
- the type of fabric/the symbol on the label  
- the colours: separate coloured garments from whites.  
• Empty all garment pockets and check the buttons.  
• Do not exceed the values listed in the “Table of wash  
cycles”, which refer to the weight of the laundry when dry.  
Load balancing system  
Before every spin cycle, to avoid excessive vibrations and  
to distribute the load in a uniform manner, the drum rotates  
continuously at a speed which is slightly greater than the  
washing rotation speed. If, after several attempts, the load is  
not balanced correctly, the machine spins at a reduced spin  
speed. If the load is excessively unbalanced, the washing ma-  
chine performs the distribution process instead of spinning.  
To encourage improved load distribution and balance, we  
recommend small and large garments are mixed in the load.  
How much does your laundry weigh?  
1 sheet 400-500 g  
1 pillow case 150-200 g  
1 tablecloth 400-500 g  
1 bathrobe 900-1200 g  
1 towel 150-250 g  
Garments requiring special care  
Outwear (wash cycle 9): is studied for washing water-  
repellent fabrics and winter jackets (e.g. Gore-Tex, polyester,  
nylon); for best results, use a liquid detergent and dosage  
suitable for a half-load; pre-treat necks, cuffs and stains if  
12  
 
Troubleshooting  
Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure  
that the problem cannot be solved easily using the following list.  
GB  
Problem:  
Possible causes / Solutions:  
The machine does not switch on.  
• The appliance is not plugged into the socket fully, or not enough to make contact.  
• There is no power to the socket, or the fuse has blown in the mains plug.  
The wash cycle does not start.  
• The door is not closed properly.  
• The ON/OFF button has not been pressed.  
• The START/PAUSE button has not been pressed.  
• The water tap has not been turned on to allow water to flow into the machine.  
• A delayed start has been set.  
The machine does not fill with wa-  
• The water inlet hose is kinked.  
ter or the indicator light for the first • The water inlet hose is not connected to the water supply.  
wash cycle stage flashes rapidly.  
• The water pressure is too low.  
• The water tap has not been turned on to allow water to flow into the machine.  
• There is no water supply to the house.  
• The inlet valve filter is blocked.  
• The START/PAUSE button has not been pressed.  
The machine continuously fills with • The top of the drain hose is too low - It must be fitted at a height between 65  
water and continually drains away  
or Water left in the drum  
or Stuck on wash.  
and 100 cm from the floor (see “Installation”).  
• The drain hose is connected incorrectly to the sink trap allowing water to run  
into the machine, the drain hose must be positioned higher than the bottom of  
the sink to prevent water flowing down the drain hose.  
• The end of the drain hose has been pushed too far down the standpipe, the  
‘U’ bracket should be fitted 100 mm from the end of the drain hose.  
The machine does not drain or  
spin.  
• The Pump filter is blocked.  
• The drain hose is kinked (see “Installation”).  
• New Installation - The blanking cap or spigot has not been removed if  
connected under a sink.  
• The drain hose or sink trap is blocked.  
• The wash cycle does not include draining, some wash cycles require the drain  
phase to be started manually.  
• The ‘Spin Speed’ selector knob is in the  
position.  
The machine does not heat or poor • The ‘Temperature’ selector knob is in the “ ” position.  
wash results.  
The programme takes too long.  
• Programme times will vary due to water pressure, the incoming water tempera-  
ture and if the wash load goes out of balance. This will increase the programme  
times accordingly (see ‘ The machine wont spin properly’ below).  
The machine vibrates a lot during  
the spin cycle.  
• The feet have not been adjusted, enabling the machine to rock.  
• New Installation - Either the Transit Bolts including the plastic spacers, or the  
Polystyrene Packaging have not been removed when installing the machine.  
• The machine is trapped between cabinets and/or walls.  
• The load is in a slight out of balance condition and machine is spinning, but at  
a lower speed.  
13  
 
The machine is noisy.  
• There will always be some motor, pump and drum noise during spin.  
GB  
The machine wont spin properly.  
• Out of Balance detected when attempting to go into a spin cycle - If this  
happens the machine will continue to try to repeat the distribution of the load  
required before the machine will go into higher spin speeds - This will increase  
the programme time accordingly. This is a safety feature to prevent damage.  
Out of Balance can be caused by washing a single heavy item (eg duvet, quilt,  
etc). - Try the programme again using a different load.  
The machine leaks from the  
dispenser.  
• The dispenser drawer is blocked with detergent and requires cleaning.  
• The water pressure is too high and requires turning down - turn down the tap  
on the water supply pipe slightly and try again.  
• The machine is tilting forwards - It must be level when in its final position.  
The machine leaks (other than  
dispenser).  
• The fill hose is loose, check both the cabinet and tap ends.  
• The fill hose is tight but still leaks, if so replace the rubber washers, or the fill  
hose is missing the rubber washer.  
• The drain hose is not fixed in properly.  
The indicator lights on the console  
are flashing rapidly.  
• Switch off the machine and unplug it, wait for approximately 1 minute and then  
switch it back on again If the problem persists contact the Technical Assistance  
Service.  
The machine smells.  
• The machine requires a service wash. Run a 90 degree wash cycle with deter-  
gent and no laundry.  
The machine door cannot be  
opened.  
• The door will not open until the door lock indicator light goes out shortly after  
the program has finished.  
Door Seal damaged at the bottom.  
• The door seal has drainage holes at the bottom - This is normal.  
• The water level is correct if it can be seen at the bottom of the door.  
The water level is too low when  
the machine is washing.  
There is too much foam.  
• The detergent is not suitable for machine washing (it should display the text  
‘for washing machines’ or ‘hand and machine wash’ or the like).  
Too much detergent was used - less detergent is required in soft water.  
After completing the programme,  
or before starting a programme,  
the machine has turned itself off  
(no lights).  
To comply with new energy saving regulations the machine is fitted with an  
automatic standby system. Press ‘ON/OFF’ button for 3 seconds to activate  
the machine, it can then either be switched off or a new programme selected.  
General.  
Your washing machine contains sensors that monitor progress during the wash  
cycle (eg: Water Levels, Temperatures, Out of Balance loads, Wash time/pro-  
gress).  
Normally, if your machine successfully completes the cycle, there is unlikely to  
be anything wrong!  
Remember, you will be charged for a service call for problems caused by incorrect installation, as listed  
above.  
Not emptying contents from pockets may cause pump or drain blockages, or may damage the machine.  
Do not wash items which do not have a wash label, or wash items that are not intended as machine  
washable.  
14  
 
Assistance  
12 Months Parts and Labour Guarantee  
GB  
Your appliance has the benefit of our manufacturers guarantee, which covers the cost of breakdown repairs for twelve  
months from the date of purchase.  
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either  
workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to you.  
This guarantee is subject to the following conditions:  
-
The appliance has been installed and operated correctly and in accordance with our operating and  
maintenance instructions.  
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.  
The appliance has been used for normal domestic purposes only.  
The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any  
person not authorised by us.  
-
-
-
Any repair work must be undertaken by us or our appointed agent.  
Any parts removed during repair work or any appliance that is replaced become our property.  
The appliance is used in the United Kingdom or Republic of Ireland.  
The guarantee does not cover:  
-
-
-
Damage resulting from transportation, improper use, neglect or interference or as a result of improper  
installation.  
Replacement of any consumable item or accessory . These include but are not limited to:  
plugs, cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.  
Replacement of any removable parts made of glass or plastic.  
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR  
NON-DOMESTIC PREMISES.  
5 Year Parts Guarantee  
Indesit also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you registering your appliance  
with us and the parts being fitted by one of our authorised engineers. There will be a charge for our engineers time. To  
activate the extra parts warranty on your appliance, simply call our registration line on 08448 24 24 24 (Republic of  
Ireland 01 230 0800)  
Extended Guarantees  
We offer a selection of repair protection plans that enable you to fully cover yourself against the expense of repair bills for the  
life of your policy. To find the ideal plan for you please call our advice line on  
08448 226 226 (Republic of Ireland 01 230 0233).  
Free Helpdesk Service  
We have a dedicated team who can provide free advice and assistance with your appliance if you experience any technical  
difficulties within the first 90 days of ownership. Simply call our Indesit Service Hotline on 08448 224 224 (Republic of  
Ireland 0818 313 413) for telephone assistance, or, where necessary, to arrange for an engineer to call.  
15  
 
195113487.00  
03/2013  
-
Xerox Fabriano  
After Sales Service  
GB  
No one is better placed to care for your Indesit appliance during the course of its working life than us - the manufacturer.  
Essential Contact Information  
Indesit Service  
We are the largest service team in Europe offering you access to 400 skilled telephone advisors and 1100 fully qualified  
engineers on call to ensure you receive fast, reliable, local service.  
UK: 08448 224 224  
Republic of Ireland: 0818 313 413  
Please note: Our advisors will require the following information:  
Model number:  
Serial number:  
Parts and Accessories  
We supply a full range of genuine replacement parts as well as accessory products that protect and hygienically clean your  
appliance to keep it looking good and functioning efficiently throughout its life.  
UK: 08448 225 225  
Republic of Ireland: 0818 313 413  
Appliance Registration  
We want to give you additional benefits of Indesit ownership. To activate your free 5 year parts guarantee you must  
register your appliance with us.  
UK: 08448 24 24 24  
Republic of Ireland: 01 230 0800  
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB  
Indesit Company Unit 49 Airways Industrial Estate, Dublin 17  
Recycling & Disposal Information  
As part of Indesits continued commitment to helping the environment, Indesit reserves the right to use quality, recycled  
components to keep down customer costs and minimise material wastage.  
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove the door, plug  
and cut the mains cable off flush with the appliance. Dispose of these parts separately to ensure that the appliance can  
no longer be plugged into a mains socket, and the door cannot be locked shut.  
16  
 

Intel Server SSR212MC2 User Manual
Invacare Crib Toy ACC250 User Manual
Invacare Mobility Aid DLX User Manual
Jasco Home Security System 57884 User Manual
Jet Tools Saw JWBS 14DX User Manual
JVC Digital Camera GC QX3 User Manual
JVC Stereo Amplifier 0199MNMMDWTKR User Manual
Kenmore Microwave Oven 87133 User Manual
KitchenAid Microwave Oven W10189714A User Manual
Kodak Camcorder 9E3721 User Manual