Instructions for use
WASHER-DRYER
!
This symbol reminds you to read this instruction manual.
GB
GB
Contents
English,1
Installation, 2-3-4-5
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Description of the washer-dryer, 6-7
Control panel
Display
How to run a wash cycle or a drying cycle, 8
Wash cycles and options, 9
Table of programmes and wash cycles
Wash options
PWDE 8148 W
Detergents and laundry, 10
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Precautions and advice, 11
General safety
Disposal
Opening the porthole door manually
Care and maintenance, 12
Cutting off the water and electricity supplies
Cleaning the washer-dryer
Cleaning the detergent dispenser drawer
Cleaning the pump
Checking the water inlet hose
Troubleshooting, 13
Service and Guarantee, 14-15-16
Before calling for Assistance
Guarantee
1
Connecting the drain hose
• the supply voltage is included within the values i
ndicated on the Technical details table
(see page 5);
GB
Connect the drain hose,
without bending it, to a
draining duct or a wall
drain situated between
65 and 100 cm from
the floor;
• the socket is compatible with the washing
machine's plug. If this is not the case, replace
the socket or the plug.
65 - 100 cm
Your appliance is now supplied with a 13 amp fused
plug it can be plugged into a 13 amp socket for
immediate use. Before using the appliance please
read the instructions below.
The drain hose may be
connected to an
WARNING - THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE
CARRIED OUT BY A QUALIFIED ELECTRICIAN.
under-sink trap. Before
connecting the drain
hose from the machine
ensure that any blanks
or removable ends
have been taken off
the spigot.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA
approved fuse to BS 1362 should always be used,
and the fuse cover re-fitted. If the fuse cover is lost,
the plug must not be used until a replacement is
obtained.
Where it connects to
the waste water pipe
cut end off spigot or
remove the blanking cap
Replacement fuse covers:
If it is place over the
edge of a basin or sink
be sure the free end of
the hose should not be
underwater.
If a replacement fuse cover is fitted, it must be of the
correct colour as indicated by the coloured marking
or the colour that is embossed in words on the base
of the plug. Replacements can be obtained directly
from your nearest Service Depot.
Removing the plug:
If your appliance has a non-rewireable moulded plug
and you should wish to re-route the mains cable
through partitions, units etc., please ensure that
either:
! We advise against the use of hose extensions; in
case of absolute need, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length.
the plug is replaced by a fused 13 ampere re-
wearable plug bearing the BSI mark of approval.
or:
the mains cable is wired directly into a 13 amp cable
outlet, controlled by a switch, (in compliance with BS
5733) which is accessible without moving the
appliance.
Ensure that if the drain hose is pushed into a
standpipe, that the end does not go down more
than 15cms (6 inches). If the hose is pushed down
too far, this may cause the machine to self -syphon
ie. continuously empty as it is filling.
Disposing of the plug:
Ensure that before disposing of the plug itself, you
make the pins unusable so that it cannot be
accidentally inserted into a socket.
Electric connection
Before plugging the appliance into the mains
socket, make sure that:
Instructions for connecting cable to an alternative plug:
Important: the wires in the mains lead are coloured in
accordance with the following code:
• the socket is earthed and in compliance with the
applicable law;
Green & Yellow Earth
Blue
Neutral
Live
• the socket is able to sustain the appliance's
maximum power load indicated in the Technical
details table (see page 5);
Brown
3
As the colours of the wires in the lead may not
correspond with the coloured markings identifyng
the terminals in your plug, proceed as follows:
Connect Green & Yellow wire to terminal marked E
Warning! The company denies all liability if and when
these norms are not respected.
GB
The first wash cycle
or
or coloured Green or Green & Yellow.
Connect Brown wire to terminal marked L or
coloured Red.
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle with
detergent and no laundry, setting the 90°C
programme without a pre-wash cycle.
Connect Blue wire to terminal marked N or coloured
Black.
If a 13 amp plug (BS 1363) is used it must be fitted
with a
13 amp fuse, either in the plug or adaptor or at the
distribution board.
If you are in any doubt the electrical supply to your
machine, consult a qualified electrician before use.
How to connect an alternative plug:
The wires in this mains lead are coloured in
accordance with the following code:
BLUE
NEUTRAL (N)
LIVE (L)
BROWN
GREEN & YELLOW
EARTH (E)
Disposing of the appliance:
When disposing of the appliance please remove the
plug by cutting the mains cable as close as possible
to the plug body and dispose of it as described
above.
GREEN &
YELLOW
13 ampere fuse
BROWN
CROSS-BAR
CORD GRIP
BLUE
! The washing machine should not be installed in an
outdoor environment, not even when the area is
sheltered, because it may be very dangerous to
leave it exposed to rain and thunderstorms.
! When the washing machine is installed, the mains
socket must be within easy reach.
! Do not use extensions or multiple sockets.
! The power supply cable must never be bent or
dangerously compressed.
! The power supply cable must only be replaced by
an authorised serviceman.
4
GB
Technical data
Model
PWDE 8148 W
width 59,5 cm
height 85 cm
depth 62 cm
Dimensions
Capacity
from 1to 8 kg for wash programme
from 1 to 6 kg for the drying programme
Electrical
please refer to the technical data
plate fixed to the machine
connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 62 litres
Water connections
Spin speed
up to 1400 rotations per minute
Wash: programme 1; temperature
60°C; using a load of 8 kg.
Energy rated
programmes
according to
regulation
Drying: first drying cycle performed
with a 2 kg load, by selecting the
drying level "A1" (IRON);
Second drying cycle performed with a
6 kg load, selecting the maximum
drying level "A4" (EXTRA).
EN 50229
This appliance conforms to the
following EC Directives:
- 89/336/EEC dated 03/05/89
(Electromagnetic Compatibility) and
subsequent modifications
- 2006/95/EC (Low Voltage)
- 2002/96/EC
5
Description of the washer-dryer
Control panel
GB
OPTION
buttons and
indicator lights
DOOR
LOCKED
indicator light
ON/OFF
button
TEMPERATURE
button
DISPLAY
WASH
CYCLE
SELECTOR
KNOB
SPIN
button
DRYING
button
Detergent dispenser drawer
START/PAUSE
button and indicator
light
Detergent dispenser drawer: used to dispense
detergents and washing additives ( see “Detergents
and laundry”).
DRYING button
: press to decrease or exclude
drying; the selected drying level or time will appear on
the display (see "How to run a wash cycle or a drying
cycle").
ON/OFF
button: press this briefly to switch the
START/PAUSE
button and indicator light: when
machine on or off. The START/PAUSE indicator light
which flashes slowly in a blue colour shows that the
machine is switched on. To switch off the washer-
dryer during the wash cycle, press and hold the
button for approximately 3 seconds; if the button is
pressed briefly or accidentally the machine will not
switch off.
the blue indicator light flashes slowly, press the button
to start a wash cycle. Once the cycle has begun the
indicator light will remain lit in a fixed manner. To
pause the wash cycle, press the button again; the
indicator light will flash in an amber colour. If the
symbol is not illuminated, the door may be opened. To
start the wash cycle from the point at which it was
interrupted, press the button again.
If the machine is switched off during a wash cycle,
this wash cycle will be cancelled.
DOOR LOCKED
indicator light:
WASH CYCLE SELECTOR KNOB: used to set the
desired wash cycle (see “Table of programmes and
wash cycles”).
The lit symbol indicates that the door is locked. To
prevent any damage, wait until the symbol turns off
before opening the door.
To open the door while a cycle is in progress, press
the START/PAUSE button; if the DOOR LOCKED
symbol is switched off the door may be opened.
OPTION buttons and indicator lights: press to
select the available options. The indicator light
corresponding to the selected option will remain lit.
Standby mode
SPIN
button: press to reduce or completely
This washer-dryer, in compliance with new energy
saving regulations, is fitted with an automatic standby
system which is enabled after a few minutes if no
activity is detected. Press the ON-OFF button briefly
and wait for the machine to start up again.
exclude the spin cycle; the value appears on the
display.
TEMPERATURE
button: press to reduce or
completely exclude the temperature; the value
appears on the display.
6
Display
GB
B
A
C
The display is useful when programming the machine and provides a great deal of information.
The duration of the available wash cycles and the remaining time of a running cycle appear in section A; if the
DELAYED START option has been set, the countdown to the start of the selected wash cycle will appear.
Furthermore, pressing the corresponding button allows you to view the maximum temperature, spin speed and
drying level or time values attained by the machine during the selected cycle.
The hour-glass flashes while the machine is processing data, depending on the wash cycle and Smart level
selected. After a maximum of 10 minutes, the “hour-glass” icon remains lit in a fixed manner and the final amount
of time remaining is displayed. The hour-glass icon will then switch off approximately 1 minute after the final
amount of time remaining has appeared.
The phases scheduled for the selected cycle and, once the cycle has begun, the current phase of the wash cycle
(and drying cycle, if applicable) appear in section B:
Main wash
Rinse
Spin/Drain
Drying
The icons corresponding to “temperature”, “spin” and “drying” (working from the left) are displayed in section C.
The “temperature” bars
The “spin” bars
indicate the maximum temperature level which may be selected for the set cycle.
indicate the maximum spin level which may be selected for the set cycle.
The
symbol lights up while the drying settings are being adjusted.
7
How to run a wash cycle or a
drying cycle
1. SWITCH THE MACHINE ON. Press the
button; the START/PAUSE indicator light will flash
slowly in a blue colour.
If your laundry load to be washed and dried is
much greater than the maximum stated load (see
adjacent table of programmes), perform the wash
cycle, and when the cycle is complete, divide the
garments into groups and put some of them back
in the drum. At this point, follow the instructions
provided for a "Drying only" cycle. Repeat this
procedure for the remainder of the load.
GB
2. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes and wash cycles on the following page.
3. MEASURE OUT THE DETERGENT. Pull out the
detergent dispenser drawer and pour the detergent
into the relevant compartments as described in
“Detergents and laundry”.
A cooling-down period is always added to the end
of each drying cycle.
Drying only
Use the cycle selector knob to select a drying cycle
(11-12-13) in accordance with the type of fabric.
The desired drying level or time may also be set
4. CLOSE THE DOOR.
5. SELECT THE WASH CYCLE. Use the WASH
CYCLE SELECTOR knob to select the desired wash
cycle. A temperature and spin speed is set for each
wash cycle; these values may be adjusted. The
duration of the cycle will appear on the display.
using the DRYING button
.
Modify the cycle settings.
• Press the button to enable the option; the indicator
light corresponding to the button will switch on.
• Press the button again to disable the option; the
indicator light will switch off.
6. CUSTOMISE THE WASH CYCLE. Use the
relevant buttons:
! If the selected option is not compatible with the
set wash cycle, the indicator light will flash and the
option will not be activated.
Modify the temperature and/or spin
speed. The machine automatically displays the
maximum temperature and spin speed values set for
the selected cycle, or the most recently-used settings
if they are compatible with the selected cycle. The
temperature can be decreased by pressing the
button, until the cold wash “OFF” setting is reached.
The spin speed may be progressively reduced by
! If the selected option is not compatible with a
previously selected one, the indicator light
corresponding to the first function selected will flash
and only the second option will be activated; the
indicator light for the option which has been
activated will be illuminated.
pressing the button, until it is completely excluded
(the “OFF” setting). If these buttons are pressed
Note: if the SMART option has been selected,
none of the incompatible options may be activated.
again, the maximum values are restored.
! The options may affect the recommended load
value and/or the duration of the cycle.
Setting the drying cycle
The first time the button
is pressed, the machine
7. START THE WASH CYCLE. Press the START/
PAUSE button. The corresponding indicator light will
turn blue, remaining lit in a fixed manner, and the
will automatically select the maximum drying cycle
which is compatible with the selected wash cycle.
Subsequent presses will decrease the drying level and
then the drying time, until the cycle is excluded
completely ("OFF"). If these buttons are pressed
again, the maximum values are restored.
door will be locked (the DOOR LOCKED
symbol
will be lit). To change a wash cycle while it is in
progress, pause the washer-dryer using the
START/PAUSE button (the START/PAUSE indicator
light will flash slowly in an amber colour); then
select the desired cycle and press the START/
PAUSE button again. To open the door while a
cycle is in progress, press the START/PAUSE
Drying may be set as follows:
A- Based on the desired laundry dryness level:
Iron: suitable for clothes which will need ironing
afterwards. the remaining dampness softens
creases, making them easier to remove. "A1"
appears on the display.
button; if the DOOR LOCKED
symbol is switched
off the door may be opened. Press the START/
PAUSE button again to restart the wash cycle from
the point at which it was interrupted.
Hanger: ideal for clothes which do not need to be
dried fully. "A2" appears on the display.
Cupboard: suitable for laundry which can be put
back in a cupboard without being ironed. "A3"
appears on the display.
8. THE END OF THE WASH CYCLE. This will be
indicated by the text “END” on the display; when
the DOOR LOCKED
symbol switches off the door
Extra: suitable for garments which need to be dried
completely, such as sponges and bathrobes. "A4"
appears on the display.
may be opened. Open the door, unload the laundry
and switch off the machine.
! If you wish to cancel a cycle which has already
begun, press and hold the
B - Based on a set time period: between 30 and 180
minutes (Max. load 4 kg).
button. The cycle will be
stopped and the machine will switch off.
8
Wash cycles and options
Table of programmes and wash cycles
GB
Description of the wash cycle
Max.
temp.
(°C)
Max.
speed
(rpm)
Detergents
Main wash
Max.
load
(kg)
Cycle
duration
Fabric
softener
Drying
Smart cycles.
White Cotton: extremely soiled
whites.
1
1
1
2
3
4
90°
60°
40°
60°
40°
40°
1400
1400
1400
1400
1400
800
8
8
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
White Cotton (1)
: heavily soiled
whites and resistant colours.
White Cotton (2): heavily soiled
whites and delicate colours.
Cotton: heavily soiled whites and
resistant colours.
Coloured Cotton(3): lightly soiled
whites and delicate colours.
Synthetics: heavily soiled resistant
colours.
8
8
8
3,5
5
6
Jeans
40°
40°
800
600
4
2
•
•
•
•
•
•
Shirts
Special cycles
7
8
Wool: for wool, cashmere, etc.
40°
30°
30°
30°
800
0
2
2
3
•
-
•
•
•
•
•
•
•
•
Delicates: for garments in silk and
viscose, lingerie.
9
Duvet: for down-stuffed garments
1000
600
-
Max.
2 pairs
10
Sport Shoes
-
Dry cycles
Cottons
11
12
13
-
-
-
-
-
-
-
-
-
-
-
-
6
3,5
2
•
•
•
Synthetics
Wool
Partial cycles
Rinse
-
-
-
1400
1400
0
-
-
-
8
8
8
•
•
-
•
-
Spin
Drain
-
For all Test Institutes:
1) Test wash cycle in compliance with regulation EN 50229: select wash cycle 1 with a temperature of 60°C.
2) Long wash cycle for cottons: select wash cycle 1 with a temperature of 40.
3) Short wash cycle for cottons: select wash cycle 3 with a temperature of 40.
Wash options
Note: If you also want to run the drying cycle, this option
is enabled only if combined with level “A1” (Iron dry).
The
option optimises washing to suit the quantity
of laundry loaded into the machine, thereby reducing the
overall wash cycle duration while minimising water and
Cool Wash
The Cool Wash function saves energy by not heating
the water used to wash your laundry – an advantage
both to the environment and to your energy bill.
Instead, intensified wash action and water
optimisation ensure great wash results in the same
average time of a standard cycle.
energy consumption. Press the
the type of wash cycle desired:
button to select
Intense: vigorous wash cycle for garments with a heavy soil level.
Perform: standard wash cycle for garments with a normal
soil level.
Fast: quick wash cycle for garments with a light soil level.
! This may only be used in conjunction with wash cycles 1, 2,
3, 4 (all three levels) and 5, 6 (Perform and Fast levels).
For the best washing results we recommend the
usage of a liquid detergent.
! It cannot be used in conjunction with wash cycles
Easy iron
6, 7, 8, 9, 10, 11, 12, 13,
,
,
.
By selecting this function, the wash and spin cycles will be
modified in order to reduce the formation of creases. At the
end of the cycle the washer-dryer will perform slow rotations
of the drum, while the EASY IRON and START/PAUSE
indicator lights will flash (blue and orange respectively). To end
the cycle, press the START/PAUSE button or the EASY IRON
button. For wash cycles number 8, the machine will end the
cycle while the laundry is soaking; the EASY IRON and
START/PAUSE indicator lights will flash. To drain the water so
that the laundry may be removed, press the START/PAUSE
button or the EASY IRON button.
Delayed start
To set a delayed start for the selected cycle, press the
corresponding button repeatedly until the required delay
period has been reached. When this option is enabled,
the corresponding indicator light will remain lit. To
remove the delayed start setting, press the button until
the text "OFF" appears on the display.
! This option can be used in conjunction with all cycles.
! It cannot be used in conjunction with wash cycles 7, 10,
11, 12, 13,
,
.
9
Detergents and laundry
Detergent dispenser drawer
Wool: wash cycle 7 can be used to wash all woollen
garments in the machine, even those carrying the “hand
wash only” label. To achieve the best results, use a
GB
Successful washing results also depend on the correct
dose of detergent: adding too much detergent will not
necessarily result in a more efficient wash, and may in
fact cause build up on the inside of your appliance and
contribute to environmental pollution.
special detergent and do not exceed the maximum load
of 2 kg.
Delicates: use special wash cycle 8 to wash all silk
garments. We recommend the use of special detergent
which has been designed to wash delicate clothes.
Curtains: we recommend you fold the curtains and
place them in a pillow case or mesh bag. Use wash
cycle 8.
! Do not use hand washing detergents; they create too
much foam.
Open the detergent
dispenser drawer and pour
Duvet: to wash double or single duvets (the weight of
which should not exceed 3 kg), cushions or clothes
padded with goose down such as puffa jackets, use the
special wash cycle number 9 “Duvet”. We recommend
that duvets are placed in the drum with their edges
folded inwards (see figure) and that no more than ¾ of
the total volume of the drum is used.
in the detergent or washing
C
additive, as follows.
B
A
To achieve the best results, we recommend that a liquid
detergent is used and placed inside the detergent
dispenser drawer.
Compartment A: Washing detergent (powder or
liquid)
Liquid detergent should only be poured in immediately
prior to the start of the wash cycle.
Compartment B: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
extra compartment C: we recommend this
compartment is used for liquid detergent.
Preparing the laundry
• Divide the laundry according to:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from
whites.
Sport Shoes (wash cycle 10): is for washing sports
shoes; for best results, do not wash more than 2 pairs
simultaneously.
• Empty all garment pockets and check the buttons.
• Do not exceed the listed values, which refer to the
weight of the laundry when dry:
Durable fabrics: max. 8 kg
Load balancing system
Synthetic fabrics: max. 3,5 kg
Delicate fabrics: max. 2 kg
Before every spin cycle, to avoid excessive vibrations
before every spin and to distribute the load in a
uniform manner, the drum rotates continuously at a
speed which is slightly greater than the washing
rotation speed. If, after several attempts, the load is
not balanced correctly, the machine spins at a
reduced spin speed. If the load is excessively
unbalanced, the washer-dryer performs the
distribution process instead of spinning. To encourage
improved load distribution and balance, we
recommend small and large garments are mixed in
the load.
Wool: max. 2 kg
Silk: max. 2 kg
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1,200 g
1 towel 150-250 g
Special wash cycles
Jeans: turn the garments inside out before washing
and use liquid detergent. Use wash cycle 5.
Shirts: use special wash cycle 6 to wash shirts in
various fabrics and colours.
It guarantees maximum care is taken of the garments
and minimises the formation of creases.
10
Precautions and tips
! This washer-dryer was designed and constructed in
accordance with international safety regulations. The
following information is provided for safety reasons and
must therefore be read carefully.
• Do not use the appliance to dry foam rubber or
similar elastomers.
• Make sure that the water tap is turned on during
the drying cycles.
GB
General safety
Disposal
• Disposing of the packaging materials:
observe local regulations so that the packaging may
be re-used.
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
• Do not dry unwashed items in the tumble dryer.
Items that have been soiled with substances such as
cooking oil, acetone, alcohol, petrol, kerosene, spot
removers, turpentine, waxes and wax removers
should be washed in hot water with an extra amount
of detergent before being dried in the tumble dryer.
Items such as foam rubber (latex foam), shower
caps, waterproof textiles, rubber backed articles
and clothes or pillows fitted with foam rubber pads
should not be dried in the tumble dryer.
• The European Directive 2002/96/EC relating to Waste
Electrical and Electronic Equipment (WEEE) states
that household appliances should not be disposed of
using the normal solid urban waste cycle. Exhausted
appliances should be collected separately in order to
optimise the cost of re-using and recycling the
materials inside the machine, while preventing
potential damage to the atmosphere and to public
health. The crossed-out dustbin is marked on all
products to remind the owner of their obligations
regarding separated waste collection.
For more information relating to the correct disposal of
household appliances, owners should contact their
local authorities or appliance dealer.
Fabric softeners, or similar products, should be
used as specified by the fabric softener instructions.
The final part of a tumble dryer cycle occurs without
heat (cool down cycle) to ensure that the items are
left at a temperature that ensures that the items will
not be damaged.
WARNING: Never stop a tumble dryer before the end
of the drying cycle unless all items are quickly removed
and spread out so that the heat is dissipated.
• This appliance was designed for domestic use only.
• Do not touch the machine when barefoot or with wet
or damp hands or feet.
Opening the porthole door manually
In the event that it is not possible to open the porthole
door due to a powercut, and if you wish to remove the
laundry, proceed as follows:
1. Remove the plug from the
electrical socket..
2. Make sure the water level
inside the machine is lower
than the door opening; if it is
not, remove excess water
using the drain hose,
• Do not pull on the power supply cable when
unplugging the appliance from the electricity socket.
Hold the plug and pull.
collecting it in a bucket as
indicated in the figure.
• Do not open the detergent dispenser drawer while the
machine is in operation.
• Do not touch the drained water as it may reach
extremely high temperatures.
3. Remove the cover panel on the lower front part of the
washer-dryer (see overleaf).
• Never force the porthole door. This could damage the safety
lock mechanism designed to prevent accidental opening.
• If the appliance breaks down, do not under any
circumstances access the internal mechanisms in an
attempt to repair it yourself.
• Always keep children well away from the appliance
while it is operating.
• The door can become quite hot during the wash cycle.
• If the appliance has to be moved, work in a group of
two or three people and handle it with the utmost
care. Never try to do this alone, because the
appliance is very heavy.
• Before loading laundry into the washer-dryer, make
sure the drum is empty.
• During the drying phase, the door tends to get quite hot.
• Do not use the appliance to dry clothes that have
been washed with flammable solvents (e.g.
trichlorethylene).
4. Pull outwards using the tab as indicated in the figure,
until the plastic tie-rod is freed from its stop position; pull
downwards and open the door at the same time.
5. Reposition the panel, making sure the hooks are
securely in place before you push it onto the appliance.
11
Care and maintenance
Cutting off the water and electricity
supplies
2. Unscrew the lid by
rotating it anti-clockwise
(see figure): a little water
may trickle out. This is
perfectly normal.
GB
• Turn off the water tap after every wash cycle. This
will limit wear on the hydraulic system inside the
washer-dryer and help to prevent leaks.
• Unplug the washer-dryer when cleaning it and during
all maintenance work.
Cleaning the washer-dryer
3. Clean the inside thoroughly.
4. Screw the lid back on.
The outer parts and rubber components of the
appliance can be cleaned using a soft cloth soaked in
lukewarm soapy water. Do not use solvents or
abrasives.
5. Reposition the panel, making sure the hooks are
securely in place before you push it onto the
appliance.
Cleaning the detergent dispenser
drawer
Checking the water inlet hose
To remove the drawer, press
Check the inlet hose at least once a year. If there are
any cracks, it should be replaced immediately: during
the wash cycles, water pressure is very strong and a
cracked hose could easily split open.
1
lever (1) and pull the drawer
outwards (2) (see figure).
Wash it under running
water; this procedure should
be repeated frequently.
! Never use second-hand hoses.
2
Cleaning the pump
The washer-dryer is fitted with a self-cleaning pump
which does not require any maintenance. Sometimes,
small items (such as coins or buttons) may fall into the
protective pre-chamber at the base of the pump.
! Make sure the wash cycle has finished and unplug
the appliance.
To access the pre-chamber:
1. Take off the cover panel
on the front of the
machine by first pressing it
1
in the centre and then
pushing downwards on
both sides until you can
2
3
remove it (see figures).
12
Troubleshooting
Your washer-dryer could occasionally fail to work. Before contacting the Technical Assistance Service (see “
Service”), make sure that the problem cannot be not solved easily using the following list.
GB
Problem:
Possible causes / Solutions:
The washer-dryer does not
switch on.
• The appliance is not plugged into the socket fully, or not enough to make
contact.
• There is no power in the house.
The wash cycle does not start. • The washer-dryer door is not closed properly.
• The ON/OFF button has not been pressed.
• The START/PAUSE button has not been pressed.
• The water tap has not been opened.
• A delayed start has been set.
The washer-dryer does not fill
with water (the text “H2O”
flashes on the display).
• The water inlet hose is not connected to the tap.
• The hose is bent.
• The water tap has not been opened.
• There is no water supply in the house.
• The pressure is too low.
• The START/PAUSE button has not been pressed.
The washer-dryer continuously • The drain hose is not fitted at a height between 65 and 100 cm from the floor
takes in and drains water.
(see “Installation”).
• The free end of the hose is under water (see “Installation”).
• The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, turn off the water tap, switch the
appliance off and contact the Technical Assistance Service. If the dwelling is on one
of the upper floors of a building, there may be problems relating to water drainage,
causing the washer-dryer to fill with water and drain continuously. Special anti-
draining valves are available in shops and help to prevent this inconvenience.
The washer-dryer does not
drain or spin.
• The wash cycle does not include draining: some cycles require the draining
process to be enabled manually.
• The EASY IRON option is enabled: To complete the wash cycle, press the
START/PAUSE button (see “Wash cycles and options”).
• The drain hose is bent (see “Installation”).
• The drainage duct is clogged.
The washer-dryer vibrates a lot • The drum was not unlocked correctly during installation (see “Installation”).
during the spin cycle.
• The washer-dryer is not level (see “Installation”).
• The washer-dryer is trapped between cabinets and walls (see “Installation”).
The washer-dryer leaks.
• The water inlet hose is not screwed on properly (see “Installation”).
• The detergent dispenser drawer is blocked (for cleaning instructions, see “Care
and maintenance”).
• The drain hose is not fixed properly (see “Installation”).
The “option” and START/PAUSE
indicator lights flash rapidly and
an error code appears on the
display (e.g.: F-01, F-..).
• Switch off the machine and unplug it, wait for approximately 1 minute and
then switch it back on again.
If the problem persists, contact the Technical Assistance Service.
There is too much foam.
• The detergent is not suitable for machine washing (it should display the text
“for washer-dryers” or “hand and machine wash”, or the like).
• Too much detergent was used.
The washer-dryer does not dry.
• The appliance is not plugged into the socket, or not enough to make contact.
• There has been a power failure.
• The appliance door is not shut properly.
• A DELAY TIMER has been set.
• DRYING is in the OFF position.
13
Service
Before contacting the Technical Assistance Service:
GB
• Check whether you can solve the problem alone (see “Troubleshooting”).
• Restart the wash cycle to check whether the problem has been solved.
• If this is not the case, contact an authorised Technical Assistance Centre.
! Always request the assistance of authorised technicians.
Have the following information to hand:
• the type of problem;
• the appliance model (Mod.);
• the serial number (S/N).
This information can be found on the data plate applied to the rear of the washer-dryer, and can also be found on
the front of the appliance by opening the door.
14
Guarantee
12 Months Parts and Labour Guarantee
GB
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown repairs for twelve
months from the date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either
workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to you.
This guarantee is subject to the following conditions:
-
The appliance has been installed and operated correctly and in accordance with our operating and
maintenance instructions.
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.
The appliance has been used for normal domestic purposes only.
The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any
person not authorised by us.
-
-
-
Any repair work must be undertaken by us or our appointed agent.
Any parts removed during repair work or any appliance that is replaced become our property.
The appliance is used in the United Kingdom or Republic of Ireland.
The guarantee does not cover:
-
-
-
Damage resulting from transportation, improper use, neglect or interference or as a result of improper
installation.
Replacement of any consumable item or accessory . These include but are not limited to:
plugs, cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.
Replacement of any removable parts made of glass or plastic.
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR
NON-DOMESTIC PREMISES.
5 Year Parts Guarantee
Indesit also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you registering your
appliance with us and the parts being fitted by one of our authorised engineers. There will be a charge for our engineer's
time. To activate the extra parts warranty on your appliance, simply call our registration line on 08448 24 24 24
(Republic of Ireland 01 230 0800).
Extended Guarantees
We offer a selection of repair protection plans that enable you to fully cover yourself against the expense of repair bills for
the life of your policy. To find the ideal plan for you please call our advice line on
08448 226 226 (Republic of Ireland 01 230 0233).
Free Helpdesk Service
We have a dedicated team who can provide free advice and assistance with your appliance if you experience any technical
difficulties within the first 90 days of ownership. Simply call our Indesit Service Hotline on 08448 224 224 (Republic of
Ireland 0818 313 413) for telephone assistance, or, where necessary, to arrange for an engineer to call.
15
195080034.00
07/2009
-
Xerox Fabriano
After Sales Service
GB
No one is better placed to care for your Indesit appliance during the course of its working life than us - the manufacturer.
Essential Contact Information
Indesit Service
We are the largest service team in Europe offering you access to 400 skilled telephone advisors and 1100 fully qualified
engineers on call to ensure you receive fast, reliable, local service.
UK: 08448 224 224
Republic of Ireland: 0818 313 413
Please note: Our advisors will require the following information:
Model number:
Serial number:
Parts and Accessories
We supply a full range of genuine replacement parts as well as accessory products that protect and hygienically clean
your appliance to keep it looking good and functioning efficiently throughout its life.
UK: 08448 225 225
Republic of Ireland: 0818 313 413
Appliance Registration
We want to give you additional benefits of Indesit ownership. To activate your free 5 year parts guarantee you must
register your appliance with us.
UK: 08448 24 24 24
Republic of Ireland: 01 230 0800
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB
Indesit Company Unit 49 Airways Industrial Estate, Dublin 17
Recycling & Disposal Information
As part of Indesit's continued commitment to helping the environment, Indesit reserves the right to use quality, recycled
components to keep down customer costs and minimise material wastage.
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove the door, plug
and cut the mains cable off flush with the appliance. Dispose of these parts separately to ensure that the appliance can
no longer be plugged into a mains socket, and the door cannot be locked shut.
16
|