Instructions for use
WASHING MACHINE
Contents
AUS
Installation, 2-3
Unpacking and levelling
AUS
Connecting the electricity and water supplies
The first wash cycle
English,1
Technical data
Description of the washing machine, 4-5
Control panel
Display
Running a wash cycle, 6
Wash cycles and options, 7
Table of programmes and wash cycles
Wash options
Detergents and laundry, 8
Detergent dispenser drawer
Preparing the laundry
PWE 8147 S
Special wash cycles
Precautions and advice, 9
General safety
Disposal
Care and maintenance, 10
Cutting off the water and electricity supplies
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Troubleshooting, 11
Service, 12
1
Connecting the drain hose
! Avoid using any extension cord or multiple socket outlet.
! CAUTION: if this appliance is supplied from a cord
extension set or electrical portable outlet device, the cord
extension set or electrical portable outlet device
AUS
Connect the drain hose,
without bending it, to a
drainage duct or a wall
drain located at a height
between 65 and 100 cm
from the floor;
must be positioned so that it is not subject to splashing or
ingress of moisture.
65 - 100 cm
! The cable should not be bent or compressed.
! The cable should be replaced only by authorised
technicians.
! If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
alternatively, rest it on
the side of a washbasin
or bathtub, fastening the
duct supplied to the tap
(see figure). The free end
of the hose should not be
underwater.
Warning! The company shall not be held responsible
for any incidents that occur if these regulations are not
observed.
The first wash cycle
Once the appliance has been installed, and before you use
it for the first time, run a wash cycle with detergent and no
laundry, using the wash cycle 2.
! We advise against the use of hose extensions; if it is
absolutely necessary, the extension must have the same
diameter as the original hose and must not exceed 150 cm
in length.
Technical data
Model
PWE 8147 S
Electrical connection
width 59.5 cm
height 85 cm
depth 60 cm
Dimensions
Capacity
Before inserting the plug into the electrical socket, make
sure that:
from 1 to 8,5 kg
• the socket is earthed and complies with current
regulations;
Electrical
please refer to the technical data plate
fixed to the machine
connections
• the socket can withstand the maximum load of the
appliance, which is indicated in the Technical data table
(see opposite);
maximum pressure 1 MPa (10 bar)
Water connections minimum pressure 0.05 MPa (0.5 bar)
drum capacity 62 litres
• the power supply voltage falls within the values indicated
Spin speed
up to 1400 rotations per minute
in the Technical data table (see opposite);
Energy rated
programmes
according to
regulation
• the socket is compatible with the plug of the appliance.
If this is not the case, either the socket or the plug must
be replaced.
program Cotton; temperature 60°C, 1400
rpm, using a load of 8,5 kg.
AS/NZS 2040.2
! The machine must not be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
appliance exposed to rain, storms and other weather
conditions.
This appliance conforms to the following
EC Directives:
- 2004/108/EC (Electromagnetic Compa-
tibility)
- 2006/95/EC (Low Voltage)
- 2002/96/EC
! Once the machine has been installed, the electricity
socket should be easily accessible.
3
Description of the washing
machine
Control panel
AUS
OPTION
DOOR
buttons and
TEMPERATURE
ON/OFF
indicator lights
LOCKED
button
button
indicator light
DISPLAY
DELAY
WASH
SPIN
TIMER
CYCLE
Detergent dispenser drawer
START/PAUSE
button and indicator
light
button
button
SELECTOR
KNOB
Detergent dispenser drawer: used to dispense
detergents and washing additives ( see “Detergents and
laundry”).
DELAY TIMER
for the selected wash cycle; the delay period appears on
the display.
button: press to set a DELAY TIMER
ON/OFF
button: press this briefly to switch the
START/PAUSE
button and indicator light: when the
machine on or off. The START/PAUSE indicator light
which flashes slowly in a blue colour shows that the
machine is switched on. To switch off the washing
machine during the wash cycle, press and hold the
button for approximately 3 seconds; if the button is
pressed briefly or accidentally the machine will not switch
off.
blue indicator light flashes slowly, press the button to start
a wash cycle. Once the cycle has begun the indicator light
will remain lit in a fixed manner. To pause the wash cycle,
press the button again; the indicator light will flash in an
amber colour. If the symbol is not illuminated, the door
may be opened (wait approximately 3 minutes). To start
the wash cycle from the point at which it was interrupted,
press the button again.
If the machine is switched off during a wash cycle, this
wash cycle will be cancelled.
DOOR LOCKED indicator light:
WASH CYCLE SELECTOR KNOB: used to set the
desired wash cycle (see “Table of programmes and wash
cycles”).
The lit symbol indicates that the door is locked. To prevent
any damage, wait until the symbol turns off before opening
the door (wait approximately 3 minutes).
To open the door while a cycle is in progress, press the
START/PAUSE button; if the DOOR LOCKED symbol is
switched off the door may be opened.
OPTION buttons and indicator lights: press to select
the available options. The indicator light corresponding to
the selected option will remain lit.
Standby mode
SPIN
button: press to reduce or completely exclude
This washing machine, in compliance with new energy
saving regulations, is fitted with an automatic standby
system which is enabled after about 30 minutes if no
activity is detected. Press the ON-OFF button briefly and
wait for the machine to start up again.
the spin cycle; the value appears on the display.
TEMPERATURE
button: press to reduce or
completely exclude the temperature; the value appears
on the display.
4
Display
AUS
B
A
C
The display is useful when programming the machine and provides a great deal of information.
The duration of the available wash cycles and the remaining time of a running cycle appear in section A; if the DELAY TIMER
option has been set, the countdown to the start of the selected wash cycle will appear.
Pressing the corresponding button allows you to view the maximum spin speed and temperature values attained by the
machine during the set wash cycle, or the values selected most recently, if these are compatible with the set wash cycle.
The hour-glass flashes while the machine is processing data, depending on the wash cycle and Smart level selected.
After a maximum of 10 minutes, the “hour-glass” icon remains lit in a fixed manner and the final amount of time remaining
is displayed. The hour-glass icon will then switch off approximately 1 minute after the final amount of time remaining has
appeared.
The “wash cycle phases” corresponding to the selected wash cycle and the “wash cycle phase” of the running wash cycle
appear in section B:
Main wash
Rinse
Spin
Drain
The icons corresponding to “temperature”, “spin” and “DELAY TIMER” (working from the left) are displayed in section C.
The “temperature” bars
The “spin” bars
indicate the maximum temperature level which may be selected for the set cycle.
indicate the maximum spin level which may be selected for the set cycle.
The “delay” symbol , when lit, indicates that the set “DELAY TIMER” value has appeared on the display.
5
Running a wash cycle
1. SWITCH THE MACHINE ON. Press the
button;
only the second option will be activated; the indicator
light for the option which has been activated will be
illuminated.
AUS
the START/PAUSE indicator light will flash slowly in a
blue colour.
Note: if the SMART option has been selected, none of
the incompatible options may be activated.
2. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes and wash cycles on the following page.
! The options may affect the recommended load value
and/or the duration of the cycle.
3. MEASURE OUT THE DETERGENT. Pull out the
detergent dispenser drawer and pour the detergent into
the relevant compartments as described in “Detergents
and laundry”.
7. START THE WASH CYCLE. Press the START/
PAUSE button. The corresponding indicator light will
turn blue, remaining lit in a fixed manner, and the door
will be locked (the DOOR LOCKED symbol will be lit).
To change a wash cycle while it is in progress, pause
the washing machine using the START/PAUSE button
(the START/PAUSE indicator light will flash slowly in an
amber colour); then select the desired cycle and press
the START/PAUSE button again.
4. CLOSE THE DOOR.
5. SELECT THE WASH CYCLE. Use the WASH CYCLE
SELECTOR knob to select the desired wash cycle. A
temperature and spin speed is set for each wash cycle;
these values may be adjusted. The duration of the cycle
will appear on the display.
To open the door while a cycle is in progress, press
the START/PAUSE button; if the DOOR LOCKED
symbol is switched off the door may be opened (wait
approximately 3 minutes). Press the START/PAUSE
button again to restart the wash cycle from the point at
which it was interrupted.
6. CUSTOMISE THE WASH CYCLE. Use the relevant
buttons:
Modify the temperature and/or spin
speed. The machine automatically displays the
maximum temperature and spin speed values set for
the selected cycle, or the most recently-used settings
if they are compatible with the selected cycle. The
temperature can be decreased by pressing the
button, until the cold wash “OFF” setting is reached.
The spin speed may be progressively reduced by
8. THE END OF THE WASH CYCLE. This will be
indicated by the text “END” on the display; when the
DOOR LOCKED symbol switches off the door may be
opened (wait approximately 3 minutes). Open the door,
unload the laundry and switch off the machine.
! If you wish to cancel a cycle which has already begun,
press and hold the
button. The cycle will be stopped
pressing the
button, until it is completely excluded
and the machine will switch off.
(the “OFF” setting). If these buttons are pressed again,
the maximum values are restored.
Load balancing system
Before every spin cycle, to avoid excessive vibrations
before every spin and to distribute the load in a uniform
manner, the drum rotates continuously at a speed which
is slightly greater than the washing rotation speed. If,
after several attempts, the load is not balanced correctly,
the machine spins at a reduced spin speed. If the load is
excessively unbalanced, the washing machine performs
the distribution process instead of spinning. To encourage
improved load distribution and balance, we recommend
small and large garments are mixed in the load.
Setting a DELAY TIMER.
To set a DELAY TIMER for the selected cycle, press the
corresponding button repeatedly until the required delay
period has been reached. When this option has been
activated, the
symbol lights up on the display. To
remove the DELAY TIMER setting, press the button until
the text “OFF” appears on the display.
Modify the cycle settings.
• Press the button to enable the option; the indicator
light corresponding to the button will switch on.
• Press the button again to disable the option; the
indicator light will switch off.
! If the selected option is not compatible with the set
wash cycle, the indicator light will flash and the option
will not be activated.
! If the selected option is not compatible with
a previously selected one, the indicator light
corresponding to the first function selected will flash and
6
Wash cycles and options
Table of programmes and wash cycles
AUS
Detergents
Prewash Main wash Bleach
Max. Max.
temp. speed
(°C) (rpm)
Max. load Cycle
Description of the wash cycle
(kg)
duration
Fabric
softener
Smart cycles
1
2
2
2
3
4
5
6
7
White prewash: extremely soiled whites.
White Cotton: extremely soiled whites.
White Cotton: heavily soiled whites and resistant colours.
White Cotton: lightly soiled whites and delicate colours.
Cotton (1): normally soiled whites and resistant colours.
Coloured Cotton: lightly soiled whites and delicate colours.
Synthetics: heavily soiled resistant colours.
Jeans
90° 1400
90° 1400
60° 1400
40° 1400
60° 1400
40° 1400
-
-
-
-
-
-
-
-
-
8,5
8,5
8,5
8,5
8,5
8,5
3,5
4
-
60°
40°
40°
800
800
600
Shirts
2
Cold
water
MixCool 30’: to refresh lightly soiled garments quickly (not sui-
table for wool, silk and clothes which require washing by hand).
8
800
-
-
3
Special cycles
9
Wool: for wool, cashmere, etc.
40°
30°
30° 1000
600
0
-
-
-
-
-
-
-
-
-
2
2
3
10 Silk: for garments in silk and viscose, lingerie.
11 Duvet
12 Outwear
30°
400
2,5
Max.
2 pairs
13 Sport Shoes
30°
600
-
-
Partials cycles
Rinse
Spin
-
-
-
1400
1400
0
-
-
-
-
-
-
-
-
-
-
8,5
8,5
8,5
Drain
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as
water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
For all Test Institutes:
1) Test wash cycle in compliance with regulation AS/NZS 2040.2: set wash Program Cotton, with a temperature of 60°C at 1400 rpm and using a load of 8 kg.
wash cycles number 10-12, the machine will end the cycle
while the laundry is soaking; the EASY IRON and START/
PAUSE indicator lights will flash. To drain the water so that
the laundry may be removed, press the START/PAUSE
button or the EASY IRON button.
Wash options
The
option optimises washing to suit the quantity of
laundry loaded into the machine, thereby reducing the overall
wash cycle duration while minimising water and energy
consumption. Press the
wash cycle desired:
! It cannot be used in conjunction with wash cycles 8, 9,
button to select the type of
13,
,
.
Intense: vigorous wash cycle for garments with a heavy soil
level.
Perform: standard wash cycle for garments with a normal soil
level.
Fast: quick wash cycle for garments with a light soil level.
! This may only be used in conjunction with wash cycles 1, 2,
3, 4, 5 (all three levels) and 6, 7, 8 (Perform and Fast levels).
Intensive Wash
This function is particularly
useful for the removal of
stubborn stains. Insert extra
compartment 4 (supplied
with the appliance) into
4
1
3
compartment 1. When
2
pouring in the bleach, be
careful not to exceed the
“max” level marked on the
central pivot (see figure). To
bleach laundry with no other
Extra Rinse
By selecting this option, the efficiency of the rinse is increased
and optimal detergent removal is guaranteed. It is particularly
useful for sensitive skin.
! It cannot be used in conjunction with wash cycles 8,
,
.
washing action, pour the bleach into extra compartment
4, select the “Rinse” cycle and activate the “Intensive
Wash” option . To bleach during a wash cycle, pour in
the detergent and any fabric softener you wish to use,
select the desired wash cycle and enable the “Intensive
Wash” option. The use of extra compartment 4
excludes the pre-wash function.
Easy iron
By selecting this function, the wash and spin cycles will be
modified in order to reduce the formation of creases. At the end
of the cycle the washing machine will perform slow rotations of
the drum, while the EASY IRON and START/PAUSE indicator
lights will flash (blue and orange respectively). To end the cycle,
press the START/PAUSE button or the EASY IRON button. For
! It cannot be used in conjunction with wash cycles 1, 6, 8,
9, 10, 11, 12, 13,
,
.
7
Detergents and laundry
Detergent dispenser drawer
Special wash cycles
Jeans: turn the garments inside out before washing and
use liquid detergent. Use wash cycle 6.
Shirts: use special wash cycle 7 to wash shirts in various
fabrics and colours.
It guarantees maximum care is taken of the garments and
minimises the formation of creases.
MixCool 30’: this wash cycle was designed to wash
lightly soiled garments quickly: it lasts just 30 minutes
and therefore saves both energy and time. By selecting
wash cycle 8, it is possible to wash different fabrics
(except for wool and silk items) using a cold cycle, up to
a maximum load of 3 kg.
AUS
Successful washing results also depend on the correct
dose of detergent: adding too much detergent will not
necessarily result in a more efficient wash, and may in
fact cause build up on the inside of your appliance and
contribute to environmental pollution.
! Do not use hand washing detergents; they create too
much foam.
Open the detergent
dispenser drawer and pour
4
in the detergent or washing
additive, as follows.
5
1
3
Wool: wash cycle 9 can be used to wash all woollen
garments in the machine, even those carrying the “hand
2
wash only”
label. To achieve the best results, use a
special detergent and do not exceed the maximum load of
2 kg.
Silk: use special wash cycle 10 to wash all silk garments.
We recommend the use of special detergent which has
been designed to wash delicate clothes.
Compartment 1: Pre-wash detergent (powder)
Before pouring in the detergent, make sure that extra
compartment 4 has been removed.
Compartment 2: Washing detergent (powder or
liquid)
Liquid detergent should only be poured in immediately
prior to the start of the wash cycle.
Compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
Extra compartment 4: Bleach
Curtains: we recommend you fold the curtains and place
them in a pillow case or mesh bag. Use wash cycle 10.
Duvet: to wash double or single duvets (the weight
of which should not exceed 3 kg), cushions or clothes
padded with goose down such as puffa jackets, use the
special wash cycle number 11 “Duvet”. We recommend
that duvets are placed in the drum with their edges folded
inwards (see figure) and that no more than ¾ of the total
volume of the drum is used.
Extra compartment 5: we recommend this
compartment is used for liquid detergent.
To achieve the best results, we recommend that a
liquid detergent is used and placed inside the detergent
dispenser drawer.
Preparing the laundry
• Divide the laundry according to:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
• Empty all garment pockets and check the buttons.
• Do not exceed the listed values, which refer to the
weight of the laundry when dry:
Durable fabrics: max. 8,5 kg
Synthetic fabrics: max. 3,5 kg
Delicate fabrics: max. 2 kg
Wool: max. 2 kg
Silk: max. 2 kg
Outwear (wash cycle 12): is studied for washing water-
repellent fabrics and winter jackets (e.g. Gore-Tex,
polyester, nylon); for best results, use a liquid detergent
and dosage suitable for a half-load; pre-treat necks,
cuffs and stains if necessary; do not use softeners or
detergents containing softeners. Stuffed duvets cannot
be washed with this programme.
Sport Shoes (wash cycle 13): is for washing sports
shoes; for best results, do not wash more than 2 pairs
simultaneously.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1,200 g
1 towel 150-250 g
8
Precautions and tips
! This washing machine was designed and constructed
in accordance with international safety regulations. The
following information is provided for safety reasons and must
therefore be read carefully.
AUS
General safety
• This appliance was designed for domestic use only.
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
• Do not touch the machine when barefoot or with wet or
damp hands or feet.
• Do not pull on the power supply cable when unplugging the
appliance from the electricity socket. Hold the plug and pull.
• Do not open the detergent dispenser drawer while the
machine is in operation.
• Do not touch the drained water as it may reach
extremely high temperatures.
• Never force the porthole door. This could damage the safety
lock mechanism designed to prevent accidental opening.
• If the appliance breaks down, do not under any
circumstances access the internal mechanisms in an
attempt to repair it yourself.
• Always keep children well away from the appliance while
it is operating.
• The door can become quite hot during the wash cycle.
• If the appliance has to be moved, work in a group of two
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
• Before loading laundry into the washing machine, make
sure the drum is empty.
Disposal
• Disposing of the packaging materials:
observe local regulations so that the packaging may be
re-used.
• The European Directive 2002/96/EC relating to Waste
Electrical and Electronic Equipment (WEEE) states that
household appliances should not be disposed of using
the normal solid urban waste cycle. Exhausted appliances
should be collected separately in order to optimise the cost
of re-using and recycling the materials inside the machine,
while preventing potential damage to the atmosphere and
to public health. The crossed-out dustbin is marked on all
products to remind the owner of their obligations regarding
separated waste collection. For more information relating
to the correct disposal of household appliances, owners
should contact their local authorities or appliance dealer.
9
Care and maintenance
2. Unscrew the lid by
rotating it anti-clockwise
(see figure): a little water
may trickle out. This is
perfectly normal.
Cutting off the water and electricity
supplies
AUS
• Turn off the water tap after every wash cycle. This will
limit wear on the hydraulic system inside the washing
machine and help to prevent leaks.
• Unplug the washing machine when cleaning it and
during all maintenance work.
Cleaning the washing machine
3. Clean the inside thoroughly.
4. Screw the lid back on.
5. Reposition the panel, making sure the hooks are
securely in place before you push it onto the appliance.
The outer parts and rubber components of the appliance
can be cleaned using a soft cloth soaked in lukewarm
soapy water. Do not use solvents or abrasives.
Cleaning the detergent dispenser drawer
Checking the water inlet hose
To remove the drawer, press
lever (1) and pull the drawer
outwards (2) (see figure).
Wash it under running water;
this procedure should be
1
Check the inlet hose at least once a year. If there are any
cracks, it should be replaced immediately: during the wash
cycles, water pressure is very strong and a cracked hose
could easily split open.
repeated frequently.
2
! Never use second-hand hoses.
Caring for the door and drum of your
appliance
• Always leave the porthole door ajar in order to prevent
unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cleaning pump
which does not require any maintenance. Sometimes, small
items (such as coins or buttons) may fall into the protective
pre-chamber at the base of the pump.
! Make sure the wash cycle has finished and unplug the
appliance.
To access the pre-chamber:
1. Take off the cover panel
on the front of the machine
by first pressing it in the
centre and then pushing
downwards on both sides
1
until you can remove it (see
figures).
2
3
10
Troubleshooting
Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service (see “ Service”),
make sure that the problem cannot be not solved easily using the following list.
AUS
Problem:
Possible causes / Solutions:
The washing machine does not
switch on.
• The appliance is not plugged into the socket fully, or not enough to make
contact.
• There is no power in the house.
The wash cycle does not start.
• The washing machine door is not closed properly.
• The ON/OFF button has not been pressed.
• The START/PAUSE button has not been pressed.
• The water tap has not been opened.
• A DELAY TIMER has been set.
The washing machine does not fill • The water inlet hose is not connected to the tap.
with water (the text “H2O” flashes • The hose is bent.
on the display).
• The water tap has not been opened.
• There is no water supply in the house.
• The pressure is too low.
• The START/PAUSE button has not been pressed.
The washing machine
continuously takes in and drains
water.
• The drain hose is not fitted at a height between 65 and 100 cm from the floor
(see “Installation”).
• The free end of the hose is under water (see “Installation”).
• The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, turn off the water tap, switch the
appliance off and contact the Technical Assistance Service. If the dwelling is on one
of the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special anti-
draining valves are available in shops and help to prevent this inconvenience.
• The wash cycle does not include draining: some cycles require the draining
process to be enabled manually.
• The EASY IRON option is enabled: To complete the wash cycle, press the
START/PAUSE button (see “Wash cycles and options”).
• The drain hose is bent (see “Installation”).
The washing machine does not
drain or spin.
• The drainage duct is clogged.
The washing machine vibrates a
lot during the spin cycle.
• The drum was not unlocked correctly during installation (see “Installation”).
• The washing machine is not level (see “Installation”).
• The washing machine is trapped between cabinets and walls (see “Installation”).
The washing machine leaks.
• The water inlet hose is not screwed on properly (see “Installation”).
• The detergent dispenser drawer is blocked (for cleaning instructions, see “Care
and maintenance”).
• The drain hose is not fixed properly (see “Installation”).
The “option” and START/PAUSE
indicator lights flash rapidly and an
error code appears on the display
(e.g.: F-01, F-..).
• Switch off the machine and unplug it, wait for approximately 1 minute and then
switch it back on again.
If the problem persists, contact the Technical Assistance Service.
There is too much foam.
• The detergent is not suitable for machine washing (it should display the text “for
washing machines” or “hand and machine wash”, or the like).
• Too much detergent was used.
11
Service
195089142.00
11/2010
-
Xerox Fabriano
Before contacting the Technical Assistance Service:
AUS
• Check whether you can solve the problem alone (see “Troubleshooting”).
• Restart the wash cycle to check whether the problem has been solved.
• If this is not the case, contact an authorised Technical Assistance Centre.
! Always request the assistance of authorised technicians.
Have the following information to hand:
• the type of problem;
• the appliance model (Mod.);
• the serial number (S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the
front of the appliance by opening the door.
INDESIT
GENUINE ACCESSORIES
PRIORITY SERVICE
If you are not copletelly satisfied with your
appliance or require service call:
Australia
& SPARE PARTS
A wide range of genuine accessories are
available for your appliance call:
Australia
Phone: 1300 815 589
Phone: 03 9768 0888
AUSTRALIA
ARISIT PTY LIMITED
40-44 Mark Anthony Drive, Dandenong South,
VIC 3175, Australia
Fax: Service & Sales (03) 9768 0838
12
|