INTERLUDE™ SPEAKER SYSTEMS
Owner’s Guide
• IL25c
• IL36c
FIGURE 4 – Wiring diagram shows polarity connections for
one channel of a stereo or home-theater system.
WIRING THE SYSTEM
IMPORTANT: Make sure all equipment is turned off before
making any connections.
Interlude Center
Receiver or
Amplifier
(rear view)
+
-
black
red
For speaker connections, use a minimum # 16-gauge speaker
wire with polarity coding.The side of the wire with a ridge or
other coding is usually considered positive polarity (i.e., +).
+
–
(one channel shown)
NOTE: If desired, consult your local Infinity dealer about speaker
wire and connection options.
IMPORTANT: Do not reverse polarities (i.e., + to – or – to +)
when making connections. Doing so will cause poor imaging and
diminished bass response.
FIGURE 3
–
Interlude series
speakers feature
color-coded
Speaker Wire
No Marking =
Marking = +
–
Red = +
terminals.This
example shows the
most common way
of connecting
speaker wire by
directly inserting
into terminals.
Black =
–
FINAL ADJUSTMENTS
❶ Loosen Terminal
❷ Insert
Bare End;
Tighten Terminal
Check the speakers for playback first by setting the system
volume control to a minimum level, and then by applying power to
your audio system. Following the directions provided with your
receiver/processor, adjust the center-channel volume so that it
matches the output of the left and right speakers.
To ensure proper polarity, connect each + terminal on the back
of the amplifier, receiver or television to the respective + (red)
terminal on each speaker, as shown in Figure 3. Similarly,
connect the – (black) terminals in the same way.Also, see the
owner’s guides that were included with your amplifier or
receiver to confirm connection procedures.
CARE OF YOUR SPEAKER SYSTEM
Each Interlude series cabinet has a wood-vinyl finish that
does not require any routine maintenance.When needed, use
a soft cloth, dampened with water only, to remove any
fingerprints or dust.
Clean the grille by gentle vacuuming.
NOTE: Do not use any cleaning products or polishes on the
cabinet or grille.
3
INTERLUDE IL25c, IL36c
SPECIFICATIONS
IL25c
IL36c
Frequency Range:
80Hz – 22,000Hz (±3dB)
55Hz – 22,000Hz (±3dB)
Recommended
Amplifier Power Range:
15 – 150 watts
90dB spl
15 – 175 watts
91dB spl
Sensitivity:
(2.83V @ 1 meter)
Nominal Impedance:
Crossover Frequency:
8Ω
8Ω
2200Hz; 24dB/octave
800Hz, 2500Hz; 24dB/octave
Low-Frequency
Drivers:
Dual 5-1/4" (133mm) C.M.M.D.,
magnetically shielded
Dual 6-1/2" (165mm) C.M.M.D.,
magnetically shielded
Mid-Frequency
Driver:
n/a
4" (102mm) C.M.M.D.,
magnetically shielded
High-Frequency
Driver:
1" (25mm) C.M.M.D.,
magnetically shielded
1" (25mm) C.M.M.D.,
magnetically shielded
Dimensions:
(H x W x D)
7-1/2" x 20-1/2" x 7-1/2"
(191mm x 521mm x 191mm)
9" x 23" x 12-1/2"
(229mm x 584mm x 318mm)
Weight:
20lb (9.1kg)
32lb (14.6kg)
Infinity continually strives to update and improve existing products, as well as
create new ones.The specifications and construction details in this and
related Infinity publications are therefore subject to change without notice.
Declaration of Conformity
We, Infinity Systems A/S
Kongevejen 194B
DK-3460 Birkerød
DENMARK
declare in own responsibility, that the products described
in this owner’s manual are in compliance with technical
standards:
EN 50081-1:1992
EN 50082-1:1992
© 1999 Infinity Systems, Inc.
250 Crossways Park Drive,Woodbury, NY 11797 USA (800) 553-3332 (USA Only)
www.infinitysystems.com
Steen Michaelsen
Infinity Systems A/S
Birkerød. DENMARK. 12/99
Infinity is a registered trademark of Infinity Systems, Inc.
Printed in USA 12/99 Part No. 335833-001
|