PD10X-X-X
OPERATOR’S MANUAL
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
PE10X-X-X
RELEASED: 3-11-04
11-11-10
5-19-10
REVISED:
(REV. 07
1” DIAPHRAGM PUMP
08)
1:1 RATIO (METALLIC)
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
SERVICE KITS
Refer to Model Description Chart to match the pump material options.
637397 for air section repair (see page 6).
637401-XXforfluidsectionrepair(seepage4). NOTE:Thiskit alsocon-
tains several air motor seals which will need to be replaced.
637395-X major air valve assembly (see page 7).
PUMP DATA
Models . . . . . . . . . . . . . see Model Description Chart for “-XXX”
Pump Type . . . . . . . . . . Metallic Air Operated Double Diaphragm
Material . . . . . . . . . . . . . see Model Description Chart
Weight . . . PX10R-XAX-XXX . . . . . . . 20.65 lbs (9.37 kgs)
PX10R-XCX-XXX . . . . . . 35.2 lbs (16.0 kgs)
PX10R-XHX-XXX . . . . . . 39.6 lbs (18.0 kgs)
Figure 1
PX10R-XSX-XXX . . . . . . . 38.2 lbs (17.3 kgs)
MODEL DESCRIPTION CHART
add 4.65 lbs (2.11 kg) for Aluminum air motor section
add 11.09 lbs (5.03 kg) for Stainless Steel air motor section
P X 10 X - X X X - X X X
Maximum Air Inlet Pressure . . . . . . . . . 120 p.s.i.g. (8.3 bar)
Maximum Material Inlet Pressure . . . . . 10 p.s.i.g. (0.69 bar)
Maximum Outlet Pressure . . . . . . . . . . 120 p.s.i.g. (8.3 bar)
Maximum Flow Rate (flooded inlet) . . . . 52.2 g.p.m. (197.6 l.p.m.)
Displacement / Cycle @ 100 p.s.i.g. . . . 0.232 gal. (0.88 lit.)
Maximum Particle Size . . . . . . . . . . . . 1/8” dia. (3.3 mm)
Maximum Temperature Limits (diaphragm / ball / seal material)
E.P.R. / EPDM . . . . . . . . . -60_to 280_F (-51_to 138_C)
HytrelR . . . . . . . . . . . . . . -20_ to 150_ F (-29_ to 66_ C)
Nitrile . . . . . . . . . . . . . . . 10_ to 180_ F (-12_ to 82_ C)
Polypropylene . . . . . . . . . 35_ to 175_ F (2_ to 79 _ C)
SantopreneR . . . . . . . . . . -40_to 225_F (-40_to 107_C)
PTFE . . . . . . . . . . . . . . . 40_ to 225_ F (4_ to 107_ C)
VitonR . . . . . . . . . . . . . . -40_to 350_F (-40_to 177_C)
Dimensional Data . . . . . . . . . . . . . . . . see page 8
Mounting Dimension . . . . . . . . 4” x 6.25” (101.6 mm x 158.8 mm)
Noise Level @ 70 p.s.i., 60 c.p.m. . . . . . 80.6 db(A){
Electronic Interface
D - None
E - Available
Center Section Material
A - Aluminum
R - Polypropylene
S - Stainless Steel
Fluid Connection
A - 1 -- 11-1/2 N.P.T.F. - 1
B - 1 -- 11 BSP
Fluid Caps & Manifold Material
A - Aluminum
C - Cast Iron
Hardware Material
P - Plated Steel
Seat Material
A - Santoprene
C - Hytrel
E - Carbon Steel
F - Aluminum
H - Hastelloy - C
S - Stainless Steel
S - Stainless Steel
G - Nitrile
H - Hard 440 Stainless Steel
L
- Hastelloy - C
The pump sound pressure levels published here have been updated to an Equivalent
S - 316 Stainless Steel
Continuous Sound Level (L ) to meet the intent of ANSI S1.13-1971, CAGI-PNEU-
Aeq
ROP S5.1 using four microphone locations.
Ball Material
A - Santoprene
C - Hytrel
S
T
V
- 316 Stainless Steel
- PTFE
- Viton
NOTICE: All possible options are shown in the chart, however, certain
combinations may not be recommended, consult a representative or the
factory if you have questions concerning availability.
G - Nitrile
Diaphragm Material
A - Santoprene
C - Hytrel
M - Medical Grade Santoprene
T - PTFE / Santoprene
V - Viton
G - Nitrile
FLUID SECTION SERVICE KIT SELECTION
PX10X - XXX - X X X
637401 - X X
EXAMPLE: Model # PD10A-ASP-AAA
Fluid Section Service Kit # 637401-AA
Ball
Diaphragm
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET- BRYAN, OHIO 43506
(800) 276-4658 D FAX (800) 266-7016
E2010
CCN 15207657
GENERAL DESCRIPTION
OPERATING INSTRUCTIONS
The ARO diaphragm pump offers high volume delivery even at low air
pressure and a broad range of material compatibility options available.
Refer to the model and option chart. ARO pumps feature stall resistant
design, modular air motor / fluid sections.
Air operated double diaphragm pumps utilize a pressure differential in
the air chambers to alternately create suction and positive fluid pressure in
the fluid chambers, ball checks insure a positive flow of fluid.
Pump cycling will begin as air pressure is applied and it will continue to
pump and keep up with the demand. It will build and maintain line pres-
sure and will stop cycling once maximum line pressure is reached (dis-
pensing device closed) and will resume pumping as needed.
S
S
Always flush the pump with a solvent compatible with the material
being pumped if the material being pumped is subject to “setting up”
when not in use for a period of time.
Disconnecttheairsupplyfromthepumpifitistobe inactivefor afew
hours.
PARTS AND SERVICE KITS
Refertothepartviewsanddescriptionsasprovidedon page4 through7
for parts identification and Service Kit information.
S
Certain ARO “Smart Parts” are indicated which should be available
for fast repair and reduction of down time.
Service kits are divided to service two separate diaphragm pump
functions: 1. AIR SECTION, 2. FLUID SECTION. The FLUID SEC-
TION is divided further to match typical part MATERIAL OPTIONS.
S
AIR AND LUBE REQUIREMENTS
WARNING EXCESSIVE AIR PRESSURE. Can cause pump
damage, personal injury or property damage.
S
S
Afiltercapableoffilteringoutparticleslargerthan50micronsshould
be used on the air supply. There is no lubrication required other than
the “O” ring lubricant which is applied during assembly or repair.
Iflubricatedairispresent,makesurethatitiscompatiblewiththe“O”
rings and seals in the air motor section of the pump.
MAINTENANCE
S
Provide a clean work surface to protect sensitive internal moving
parts from contamination from dirt and foreign matter during service
disassembly and reassembly.
S
S
Keep good records of service activity and include pump in preven-
tive maintenance program.
INSTALLATION
Before disassembling, empty captured material in the outlet man-
ifold by turning the pump upside down to drain material from the
pump.
S
S
S
Verify correct model / configuration prior to installation.
Retorque all external fasteners per specifications prior to start up.
Pumpsare tested in water atassembly. Flushpump withcompatible
fluid prior to installation.
FLUID SECTION DISASSEMBLY
S
When the diaphragm pump is used in a forced-feed (flooded inlet)
situation, it is recommended that a “Check Valve” be installed at the
air inlet.
1. Remove (61) outlet manifold and (60) inlet manifold.
2. Remove (22) balls, (19 and 33) “O” rings (if applicable) and (21)
seats.
S
S
S
S
Material supply tubing should be at least the same diameter as the
pump inlet manifold connection.
3. Remove (15) fluid caps.
Material supply hose must be reinforced, non-collapsible type com-
patible with the material being pumped.
NOTE: Only PTFE diaphragm models use a primary diaphragm (7) and
a backup diaphragm (8). Refer to the auxiliary view in the Fluid Section
illustration.
Piping must be adequately supported. Do not use the pump to sup-
port the piping.
4. Remove the (14) screw, (6) diaphragm washer, (7) or (7 / 8) dia-
phragms, and (5) backup washer.
NOTE: Do not scratch or mar the surface of (1) diaphragm rod.
Use flexible connections (such as hose) at the suction and dis-
charge. These connections should not be rigid piped and must be
compatible with the material being pumped.
S
S
S
S
Secure the diaphragm pump legs to a suitable surface (level and
flat) to insure against damage by vibration.
FLUID SECTION REASSEMBLY
Pumps that need to be submersed must have both wet and non-wet
components compatible with the material being pumped.
Submersed pumps must have exhaust pipe above liquid level. Ex-
haust hose must be conductive and grounded.
Flooded suction inlet pressure must not exceed 10 p.s.i.g. (0.69
bar).
S
S
S
S
Reassemble in reverse order. Refer to the torque requirements on
page 5.
Clean and inspect all parts. Replace worn or damaged parts with
new parts as required.
Lubricate (1) diaphragm rod and (144) “U” cup with LubriplateR
FML-2 grease (94276 grease packet is included in service kit).
For modelswith PTFEdiaphragms: Item(8) Santoprenediaphragm
is installed with the side marked “AIR SIDE” towards the pump cen-
ter body. Install the PTFE diaphragm (7) with the side marked
“FLUID SIDE” towards the (15) fluid cap.
S
Re-check torque settings after pump has been re-started and run a
while.
S VitonR and HytrelR are trademarks of the DuPont Company S KynarR is a registered trademark of Penwalt Corp. S LoctiteR is a registered trademark of Henkel Loctite Corporation S
S SantopreneR is a registered trademark of Monsanto Company, licensed to Advanced Elastomer Systems, L.P. S LubriplateR is a registered trademark of Lubriplate Division (Fiske Brothers) S
PD10X-X-X
Page 3 of 8
PARTS LIST / PX10X-X-X FLUID SECTION
L 637401-XX FLUID SECTION SERVICE KITS INCLUDE: BALLS (see Ball Option, refer to -XX in Service Kit chart below), DIAPHRAGMS (see Diaphragm
Option, refer to -XX in Service Kit chart below), and items 19, 33, 70, 144, 175 and 180 (listed below) plus 174 and 94276 Lubriplate FML-2 grease
(page 6).
SEAT OPTIONS PX10X-XXX-XXX
BALL OPTIONS PX10X-XXX-XXX
“21”
L “22” (1-1/4” dia.)
-XXX Seat
Qty
(4)
(4)
(4)
(4)
[Mtl]
[SP]
[H]
-XXX Seat
Qty
(4)
(4)
(4)
(4)
[Mtl]
[B]
-XXX Ball
Qty
(4)
(4)
(4)
[Mtl]
[SP]
[H]
-XXX Ball
Qty
(4)
(4)
(4)
[Mtl]
[SS]
[T]
-AXX 96152-A
-CXX 96152-C
-EXX 96158
-GXX 96152-G
-HXX 94706
-XAX 93278-A
-XCX 93278-C
-XGX 93278-2
-XSX 92408
[SH]
[Ha]
[SS]
-XTX
93278-4
[C]
-LXX
95836
[B]
-XVX 93278-3
[V]
-FXX
96156
[A]
-SXX 96151
DIAPHRAGM OPTIONS PX10X-XXX-XXX
L Service Kit
L “7”
Qty
L “8”
L “19”
Qty
L “33”
-XX = (Ball)
-XXX -XX = (Diaphragm) Diaphragm
[Mtl] Diaphragm
[SP] - - - - -
Qty
- - -
- - -
- - -
- - -
(2)
[Mtl] Gasket
[Mtl] Gasket
Qty
(4)
(4)
(4)
(4)
(4)
(4)
[Mtl]
-XXA 637401-XA
-XXC 637401-XC
-XXG 637401-XG
-XXM 637401-XM
96267-A
96267-C
96267-G
96267-M
96146-T
95989-3
(2)
(2)
(2)
- - -
- - -
- - -
- - -
93280
(4)
(4)
(4)
(4)
(4)
(4)
[E]
[V]
[B]
[T]
[T]
[V]
93279
[E]
[V]
[B]
[T]
[T]
[V]
[H]
[B]
- - - - -
- - - - -
Y327-225
Y325-225
93282
Y327-220
Y325-220
93281
(2) [MSP] - - - - -
-XXT
637401-XT
(2)
(2)
[T]
[V]
96145-A
- - - - -
[SP] 93282
- - - Y327-225
93281
-XXV 637401-XV
- - -
Y327-220
NOTE: Gasket items 19 and 33 are not required with seat options -AXX, -CXX and -GXX.
CENTER SECTION OPTIONS PX10X-XXX-XXX
Aluminum
Polypropylene
Stainless Steel
PD10S-X-X PE10S-X-X
PD10A-X-X PE10A-X-X
PD10R-X-X PE10R-X-X
Item
Description (size)
Qty Part No.
Part No.
- - - - -
[Mtl] Part No.
- - - 96217
[Co] - - - - -
Part No.
96217
[Mtl] Part No.
[SS] - - - - -
Part No.
- - - - -
[Mtl]
- - -
28 Washer (8.5 mm i.d.)
43 Ground Lug
(4) - - - - -
(1) 93004
(1) 95994-2
(1) 95994-1
(2) - - - - -
(1) - - - - -
(4) 96001
(4) - - - - -
(4) 96006
(8) - - - - -
(4) 96005
93004
- - - - -
- - -
[P]
[P]
[K]
93004
93004
[Co]
[SS]
[SS]
[SS]
[SS]
[C]
68 Air Cap
95994-4
95994-3
Y17-51-S
Y17-50-S
96001
[A]
[A]
96104-1
96104-2
96104-3
96104-4
93832-3
Y17-50-S
- - - - -
96007-1
96007-2
- - - - -
96007-3
96007-4
Y17-51-S
Y17-50-S
96001
69 Air Cap
74 Pipe Plug (1/4 - 18 N.P.T. x 7/16”)
76 Pipe Plug (1/8 - 27 N.P.T. x 0.27”)
131 Screw (M8 x 1.25 - 6g x 95 mm)
(M8 x 1.25 - 6g x 100 mm)
[SS] - - - - -
[SS] - - - - -
[SS] - - - - -
- - - 96001
[SS] - - - - -
[C]
- - -
- - - - -
96216
- - - - -
96216
- - - - -
- - -
n 180 Washer
96006
[Co] - - - - -
- - - 96292
[SS] 95879
- - - - -
- - -
[B]
96006
- - - - -
96006
[Co]
- - -
L n “O” Ring (2.5 mm x 12 mm o.d.)
195 Nut (M8 x 1.25 - 6h)
- - - - -
96292
- - - - -
96005
95879
[SS] 96005
96005
[SS]
MANIFOLD / FLUID CAP MATERIAL OPTIONS PX10X-XXX-XXX
Aluminum
Cast Iron
Hastelloy-C
Stainless Steel
PX10X-XSX-XXX
PX10X-XAX-XXX
PX10X-XCX-XXX
PX10X-XHX-XXX
Item
Description (size)
Backup Washer
Diaphragm Washer
Washer (0.505” i.d.)
Qty Part No.
[Mtl] Part No.
[Mtl] Part No.
[Mtl] Part No.
[Mtl]
[SS]
[SS]
[SS]
[SS]
[SS]
[SS]
[SS]
[SS]
[SS]
5
6
9
(2) 95990-3
(2) 95990-3
(2) 93189-1
(2) 95997
[C]
[C]
95990-3
95990-3
[C]
[C]
95990-1
95990-2
[SS] 95990-1
[Ha] 95990-1
[Ha] 93189-1
[Ha] 95997
[SS] 93189-1
[SS] 95997
[SS] 96161
[SS] 96159
[CI] 96148
14 Screw (M12 x 1.75 - 6g x 25 mm)
15 Fluid Cap
(2) 95935
[A]
[A]
[A]
[A]
[A]
95831
[Ha] 96010
60 Inlet Manifold
(1) 95936-[z]
(1) 95960-[z]
(2) Y17-125
(2) 96160-2
95829-[z]
95830-[z]
Y17-55-S
96160-1
[CI]
[CI]
96150-[z]
96149-[z]
[Ha] 96008-[z]
[Ha] 96009-[z]
61 Outlet Manifold
63 Pipe Plug (1 - 11-1/2 N.P.T.)
(R 1, 1 - 11 BSP)
[SS] - - - - -
- - -
- - -
Y17-55-S
96160-1
[SS] - - - - -
z
For N.P.T.F. thread models (PX10X-AXX-XXX), use “-1”
z
For BSP thread models (PX10X-BXX-XXX), use “-2”
EXTERNAL HARDWARE OPTIONS PX10X-XXX-XXX
COMMON PARTS
PX10X-XXP-XXX
PX10X-XXS-XXX
Item
Description (size)
Qty Part No.
Mtl
[C]
[B]
[B]
[B]
Item Description (size)
Qty Part No.
Mtl Part No.
[C] 95880
[C] 95896
[C] 95879
Mtl
1
Rod
(1) 95995
26 Screw (M8 x 1.25 - 6g x 30 mm)
27 Bolt (M8 x 1.25 - 6g x 40 mm)
29 Hex Flange Nut (M8 x 1.25 - 6h)
n Air Section Service Kit Parts, see page 6.
Page 4 of 8
(8) 95880-1
(20) 95896-1
(20) 95879-1
[SS]
[SS]
[SS]
L n 70 Gasket
(2) 95843
Ln 144 “U” Cup (3/16” x 1-1/8” o.d.)
Ln 175 “O” Ring (3/32” x 13/16” o.d.)
(2) Y186-49
(2) Y325-114
PD10X-X-X
PARTS LIST / PX10X-X-X FLUID SECTION
. TORQUE REQUIREMENTS ,
COLOR CODE
DIAPHRAGM
COLOR
3
1
NOTE: DO NOT OVERTIGHTEN FASTENERS.
ALL FASTENERS ARE METRIC.
BALL
COLOR
5
8
MATERIAL
(14) screw, tighten to 25 - 30 ft lbs (33.9 - 40.7 Nm).
(26) screws, 20 - 25 ft lbs (27.1 - 33.9 Nm).
(29) nuts, 15 - 20 ft lbs (20.3 - 27.1 Nm).
Hytrel
Nitrile
Cream
Black
Tan
Cream
Red (S)
Tan
Santoprene
Santoprene
(Backup)
PTFE
9
10
Green
N / A
(131) screws, 12 - 17 ft lbs (16.3 - 23.0 Nm).
White
Yellow (-)
(-) Dash
White
Yellow (S)
(S) Dot
Viton
LUBRICATION / SEALANTS
7
6
k
Apply Lubriplate FML-2 grease to all “O” rings, “U” Cups &
mating parts.
2
4
x Apply LoctiteR 242 to threads at assembly.
- Apply PTFE tape to threads at assembly.
~ Apply Loctite 271 to threads at assembly.
U Apply anti-seize compound to threads and bolt and nut flange
heads which contact pump case when using stainless steel
fasteners.
Torque Sequence
63 - k
s Not used with PX10X-XXX-AXX, -CXX and -GXX.
Z Lubriplate FML-2 is a white food grade petroleum grease.
61
FOR THE
AIR MOTOR SECTION
SEE PAGES 6 & 7
26 , U
70 k
68
76 -
144 k
131 , x
A
70 k 29 ,
195
B
69
7
9
22
19 s
21
33 s
27 U
A
15
175 k
43
74 -
144 k
175 k
B
29 ,
27 U 1 k 180 k
5
22
63 - k
26 , U
60
6
14 , ~
19 s
21
Figure 2
MATERIAL CODE
[K] = PVDF (KynarR)
[A] = Aluminum
[B] = Nitrile
[MSP]= Medical Grade Santoprene
[P] = Polypropylene
[SH] = Hard Stainless Steel
[SP] = Santoprene
[SS] = Stainless Steel
[T] = PTFE
33 s
[C] = Carbon Steel
[CI] = Cast Iron
[Co] = Copper
[E] = E.P.R.
[H] = Hytrel
[Ha] = Hastelloy-C
[V] = Viton
AUXILIARY VIEW B-B
(models PX10R-XXX-XXX)
AUXILIARY VIEW A-A
(models PX10R-XXX-XXX)
View of two piece PTFE diaphragm
k 180
180 k
28
Santoprene 8
PTFE 7
195
PD10X-X-X
Page 5 of 8
PARTS LIST / PX10X-X-X AIR SECTION
n Indicates parts included in 637397 Air Section Service Kit shown below and items (70), (144), (175) and (180) shown on page 4.
AIR MOTOR PARTS
Item
Description (size)
Qty Part No.
(1) 95888
(1) 95970
(1) 95901
(1) 96000
[Mtl]
[A]
Item
Description (size)
Qty Part No.
(1) 95941
(1) 95833
(1) 95938
(1) 95844
(1) Y186-53
(1) Y186-49
(1) 95838
(1) 95885
(1) 96171
(1) 67164
(2) 94433
(1) Y240-9
(1) 94081
(1) Y325-119
(1) Y325-22
(2) Y325-123
(2) Y325-202
(2) 95845
(4) Y178-52-S
(1) 96172
(1) 95842
(1) 350-568
(1) 93139
(1) 95832
(4) 95924
(1) 94276
637308
[Mtl]
[Z]
[P]
[SS]
[B]
[B]
101 Center Body (PX10A-X-X)
(PX10R-X-X)
136 End Cap (PX10A-X-X)
(PX10R-X-X)
[P]
(PX10S-X-X)
[SS]
[D]
(PX10S-X-X)
103 Bushing
105 Screw (M6 x 1 - 6g)
n 137 Gasket
n 138 “U” Cup (3/16” x 1-5/8” o.d.)
n 139 “U” Cup (3/16” x 1-1/8” o.d.)
140 Valve Insert
141 Valve Plate
n 166 Gasket
(PX10A-X and PX10S-X) (16 mm long) (4) 95991
[SS]
[SS]
[SS]
[D]
[B]
(PX10R-X) (130 mm long)
107 End Plate (PX10R-X-X only)
111 Spool (PX10A-X-X and PX10S-X-X)
(PX10R-X-X)
(4) 95886
(2) 95840
(1) 95835
(1) 96293
(2) 95999
(2) 95123
(1) Y17-50-S
[AO]
[AO]
[B]
[D]
[U]
[B]
[Br]
[B]
[B]
[B]
[D]
[SS]
[D]
n 167 Pilot Piston (includes 168 and 169)
168 “O” Ring (3/32” x 5/8” o.d.)
169 “U” Cup (1/8” x 7/8” o.d.)
170 Piston Sleeve
118 Actuator Pin
121 Sleeve
128 Pipe Plug (1/8 - 27 N.P.T. x 0.27”)
(PX10A-X-X and PX10S-X-X only)
[SS]
n 171 “O” Ring (3/32” x 1-1/8” o.d.)
n 172 “O” Ring (1/16” x 1-1/8” o.d.)
n 173 “O” Ring (3/32” x 1-3/8” o.d.)
K n 174 “O” Ring (1/8” x 1/2” o.d.)
n 176 Diaphragm (check valve)
181 Roll Pin (5/32” o.d. x 1/2” long)
n 200 Gasket (PX10A-X-X and PX10S-X-X)
(PX10R-X-X)
n 132 Gasket
133 Washer (1/4”) (PX10A-X-X)
(M6) (PX10R-X-X)
(1) 96170
[B]
[C]
(3) Y117-416-C
(6) 95931
[B]
[SS]
[SS]
[SS]
[SS]
[Z]
[SP]
[SS]
[B]
(1/4”) (PX10S-X-X)
(3) Y14-416-T
134 Screw (M6 x 1 - 6g x 20 mm) (PX10R-X) (6) 95887
(PX10A-X and PX10S-X-X)
135 Valve Block (PD10A-X-X)
(PD10R-X-X)
(4) 95887
[B]
(1) 95942-3
(1) 96174-1
(1) 95939-3
(1) 95942-4
(1) 96174-2
(1) 95939-4
201 Muffler (PX10A-X-X and PX10S-X-X)
(PX10R-X-X)
[P]
[SS]
[Z]
[P]
[P]
[SS]
(PD10S-X-X)
233 Adapter Plate
(PE10A-X-X)
236 Nut (M6 x 1 - 6g) (PX10R-X-X only)
L n Lubriplate FML-2 Grease
Lubriplate Grease Packets (10)
(PE10R-X-X)
[P]
[SS]
(PE10S-X-X)
K
Fluid Section Service Kit Parts, see page 4.
AIR MOTOR SECTION SERVICE
MAJOR VALVE DISASSEMBLY
Service is divided into two parts - 1. Pilot Valve, 2. Major Valve.
GENERAL REASSEMBLY NOTES:
1. Remove (135) valve block and (233) adapter plate, exposing (132
and 166) gaskets and (176) checks.
S
Air Motor Section Service is continued from Fluid Section repair.
Inspect and replace old parts with new parts as necessary. Look for
deep scratches on surfaces, and nicks or cuts in “O” rings.
Take precautions to prevent cutting “O” rings upon installation.
Lubricate “O” rings with Lubriplate FML-2 grease.
Do not over-tighten fasteners, refer to torque specification block on
view.
2. Insertasmallflatbladescrewdriverintothenotchinthesideof(135)
valveblockandpushinontabtoremove(233)adapterplate,releas-
ing (140) valve insert, (141) valve plate, (200) gasket.
S
S
S
S
3. Remove (136) end cap and (137) gasket, releasing (111) spool.
MAJOR VALVE REASSEMBLY
S
S
Re-torque fasteners following restart.
1. Install new (138 and 139) “U” cups on (111) spool -- LIPS MUST
FACE EACH OTHER.
2. Insert (111) spool into (135) valve block.
SERVICE TOOLS -- To aid in the installation of (168) “O” rings onto
the (167) pilot piston, use tool # 204130-T, available from ARO.
3. Install(137)gasketon(136) endcap andassemble endcap to(135)
valve block, securing with (107) end plates (where applicable) and
(105) screws.
4. Install(140) valve insert and (141) valve plate into (135) valve block.
NOTE: Assemble (140) valve insert with “dished” side toward (141)
valve plate. Assemble (141) valve plate with part number identifica-
tion toward (140) valve insert.
PILOT VALVE DISASSEMBLY
1. A light tap on (118) should expose the opposite (121) sleeve, (167)
pilot piston and other parts.
2. Remove (170) sleeve, inspect inner bore of sleeve for damage.
5. Assemble(200)gasketand(233) adapterplate to(135) valveblock.
NOTE: Assemble (233) adapter plate with notched side down.
6. Assemble (132 and 166) gaskets and (176) checks to (101) body.
7. Assemble (135) valve block and components to (101) body, secur-
ing with (134) screws.
PILOT VALVE REASSEMBLY
1. Clean and lubricate parts not being replaced from service kit.
2. Install new (171 and 172) “O” rings, replace (170) sleeve.
3. Install new (168) “O” rings and (169) seal - Note the lip direction. Lu-
bricate and replace (167).
4. Reassemble remaining parts, replace (173 and 174) “O” rings.
Page 6 of 8
PD10X-X-X
PARTS LIST / PX10X-X-X AIR SECTION
173 k
118
169 k 168 k
PILOT VALVE
PART GROUP
172 k
171 k
170
k 174
121
173 k
121
167
118
166 k
174 k
233
140
141 k
135
133
U . 134
k 138
Notch
200 k
132 k 176 k 101 181 103
201
111
k 139
Insert screwdriver here to remove (233) adapter plate.
k 137
MAJOR
VALVE
- 128
136
MATERIAL CODE
[A] = Aluminum
[AO] = Alumina Oxide
[B] = Nitrile
[Br] = Brass
[C] = Carbon Steel
[D] = Acetal
[P] = Polypropylene
[SP] = Santoprene
[SS] = Stainless Steel
[U] = Polyurethane
[Z] = Zinc
U . 105
Figure 3
Models PX10A-X-X
PX10S-X-X
Models PX10R-X-X
107
Insert screwdriver here to remove (233) adapter plate.
U 105
. TORQUE REQUIREMENTS ,
133
U . 134
135
NOTE: DO NOT OVERTIGHTEN FASTENERS.
ALL FASTENERS ARE METRIC.
PX10A-X-X and PX10S-X-X: Torque (105 and 134) screws to 40 - 50 in. lbs (4.5 - 5.6 Nm).
PX10R-X-X: Torque (134) screw and (236) nut to 35 - 40 in. lbs (4.0 - 4.5 Nm).
LUBRICATION / SEALANTS
k 138
k
Apply Lubriplate FML-2 grease to “O” rings, “U” Cups & mating parts.
- Apply PTFE tape to threads at assembly.
Apply anti-seize compound to threads at assembly.
U
111
A replacement Major Valve Service Assembly is available separately, which includes the following:
637395-1 for models PD10R-X-X: 105 (4), 107 (2), 111, 132, 135, 136, 137, 138, 139, 140, 141, 166,
176 (2), 200, 233 and 236 (4).
637395-2 for models PE10R-X-X: 76, 105 (4), 107 (2), 111, 132, 135, 136, 137, 138, 139, 140, 141, 166,
176 (2), 200, 233 and 236 (4).
637395-3 for models PD10A-X-X: 105 (4), 111, 128, 132, 135, 136, 137, 138, 139, 140, 141, 166, 176
(2), 200 and 233.
k 139
k 137
136
637395-4 for models PE10A-X-X: 76, 105 (4), 111, 128, 132, 135, 136, 137, 138, 139, 140, 141, 166,
176 (2), 200 and 233.
637395-5 for models PD10S-X-X: 105 (4), 111, 128, 132, 135, 136, 137, 138, 139, 140, 141, 166, 176
(2), 200 and 233.
637395-6 for models PE10S-X-X: 76, 105 (4), 111, 128, 132, 135, 136, 137, 138, 139, 140, 141, 166,
176 (2), 200 and 233.
107
. 236
PD10X-X-X
Page 7 of 8
TROUBLE SHOOTING
Product discharged from exhaust outlet.
Low output volume, erratic flow, or no flow.
S
Check for diaphragm rupture.
S
S
S
S
S
Check air supply.
S
Check tightness of (14) diaphragm screw.
Check for plugged outlet hose.
Check for kinked (restrictive) outlet material hose.
Check for kinked (restrictive) or collapsed inlet material hose.
Check for pump cavitation -- suction pipe should be sized at least as
large as the inlet thread diameter of the pump for proper flow if high
viscosity fluids are being pumped. Suction hose must be a non-col-
lapsing type, capable of pulling a high vacuum.
Check all joints on the inlet manifolds and suction connections.
These must be air tight.
Air bubbles in product discharge.
S
S
S
Check connections of suction plumbing.
Check “O” rings between intake manifold and inlet side fluid caps.
Check tightness of (14) diaphragm screw.
Motor blows air or stalls.
S
S
S
S
Check (176) check valve for damage or wear.
Check for restrictions in valve / exhaust.
Inspect the pump for solid objectslodged in the diaphragm chamber
or the seat area.
DIMENSIONAL DATA
(Dimensions shown are for reference only, they are displayed in inches and millimeters (mm).
1 - 11-1/2 N.P.T.F. - 1 (PX10X-AXX-XXX)
1 - 11 BSP (PX10X-BXX-XXX)
Exhaust Port 3/4 - 14 N.P.T.
Air Inlet 1/4 - 18 N.P.T.
R
A
E
Q
F
P
L
Outlet
G
B
M
Inlet
D
K
N
H
C
J
DIMENSIONS
A - 12-11/32” (313.2 mm)
B - 11-9/16” (293.7 mm)
C - 4” (101.6 mm)
E - see below
F - see below
G - 12-7/16” (315.9 mm)
H - 6-1/4” (158.8 mm)
J - 7-5/16” (185.7 mm)
N - see below
K - 13/32” (10.3 mm)
L - 1-1/2” (38.1 mm)
M - 6-15/32” (164.3 mm)
P - 5-27/32” (148.2 mm)
Q - 12” (304.8 mm)
R - see below
D - 1-1/4” (31.8 mm)
“E”
“F”
“R”
“N”
PX10A-XXX-XXX
PX10R-XXX-XXX
PX10S-XXX-XXX
----------
8-1/8” (206.4 mm)
8-5/16” (211.1 mm)
8-3/16” (207.9 mm)
14-1/32” (356.2 mm)
----------
PX10X-XAX-XXX
PX10X-XCX-XXX
PX10X-XHX-XXX
PX10X-XSX-XXX
1/4” (6.4 mm)
9/32” (7.1 mm)
9/32” (7.1 mm)
9/32” (7.1 mm)
11-3/32” (281.3 mm)
----------
13-27/32” (351.4 mm)
Figure 4
PN 97999-1068
PD10X-X-X
Page 8 of 8
|