™
Intel EtherExpress
PRO/100 TX PCI
Model B
LAN Adapter
Installation Guide
Where to go for more information
Intel Fast Ethernet Networking Solutions
Intel offers a complete line of Fast Ethernet products,
including adapters, hubs, switches, and management
software. For more information, data sheets, white
papers, or demos, visit our networking website:
README files
For detailed information about the adapter, see the
README files. To view them, insert the Intel
Configuration and Drivers disk in a floppy drive,
switch to that drive, and type
Readme
Files
SETUP /README E
Topics include:
• Installing adapter drivers
• Latest news and general adapter information
• Hardware specifications and cabling information
• Adapter installation and special configurations
• Running diagnostics
World Wide Web and Online Services
You can use your modem or Internet connection to
download drivers, troubleshooting tips, and more.
(When downloading new drivers, make sure the
archive is for the PRO/100B adapter (not PRO/100).
Online services include:
• World Wide Web
• Internet FTP server
• Intel BBS
See the inside back cover for details.
Late Breaking News
This printed document provides useful information
about adapter compatibility and gives special
installation release notes. Look for the Late Breaking
News document in your shipping container.
1
Put the Adapter in the Computer
1
Turn off the computer and unplug the power cord. Then remove its cover.
Warning: Turn off and unplug power to the computer before
removing its cover. Failure to do so could shock you and may
damage the adapter or computer.
2
Remove the cover bracket from a PCI busmaster adapter slot. In most
computers, all slots are busmaster-enabled. If you have configuration
problems, see your computer’s documentation to determine if the PCI
slots are busmaster-enabled.
PCI slot
3
Push the adapter into the slot until it’s seated firmly. Then, secure the
adapter bracket with a screw.
4
5
See page 11 for specific instructions on installing multiple adapters.
Replace the computer cover and plug in the power cord.
2
Connect the Network Cable
1
Connect a single network cable to the PRO/100B TX PCI adapter as
shown below. For 100BASE-TX, your network cable must be four-pair,
category 5, twisted-pair wiring. If you plan on running the adapter at 100
Mbps, it must be connected to a 100BASE-TX hub (not a 100BASE-T4
hub). For 10BASE-T, use two-pair wiring.
100BASE-TX Wiring
Twisted Pair Ethernet (TPE).
Use category 5 cable and RJ-45
connector for this adapter. Do not
use category 3 wiring. At 100
Mbps, connect to a TX hub, not a
T4 hub. For full duplex, see
instructions on page 11.
For more information on 100BASE-TX wiring requirements and limita-
NOTE:
tions, see page 18 in this guide and refer to the README files on
the installation disk.
2
To configure the adapter, continue with the procedures specific to your
operating system on pages 4 through 10:
• DOS and Windows 3.1 users with NetWare, go to page 4
• Windows NT 4.0 and 3.5x users, go to page 6
• Windows 95 users, go to page 8
• Others, go to page 10
3
DOS and Windows 3.1 Setup for Novell
NetWare Clients
Important Note:
Windows 95 users and Windows NT should skip the
procedure on this page and go directly to page 6 for Windows
NT or page 8 for Windows 95. NetWare Client 32 users, go to
page 10.
1
Automatic configuration
PCI computers automatically detect and configure PCI-compliant adapters
while booting. The PRO/100B TX PCI adapter IRQ level and I/O memory
address are automatically set by the BIOS each time you start your computer.
Start your computer to automatically configure the adapter. Configuration is
complete when the DOS prompt appears. You can now continue with the
procedure below.
If your computer displays an error while booting, it may require additional
steps to configure a PCI adapter. See the PCI installation tips section on page
17 for more information.
2
Run Setup to install network drivers
Setup can automatically install NetWare DOS ODI client drivers for you or
display a README file with installation instructions for other NOS drivers.
1
If your computer already has network drivers installed, restart the
computer without loading them. If the drivers are loaded from the
AUTOEXEC.BAT or CONFIG.SYS file, type REMin front of each line
that loads a network driver. Or, with DOS 6.x or later press 5 as DOS
starts, to bypass the drivers.
2
3
Insert the Intel Configuration and Drivers disk in a floppy drive, switch
to that drive, and at the DOS prompt, type
SETUP
E
If you have more than one Intel PRO series PCI adapter in your
computer, an adapter selection menu appears on the screen. Select the
adapter you want by noting the Ethernet address. See page 11 for more
information on multiple adapters.
4
Select Automatic Setup from the Main menu. Then follow the instruc-
tions on the screen. (If you want to test the adapter with a responder on
the network, see the next procedure.)
4
Setup displays the adapter’s configuration, then runs a series of diagnos-
tic tests that makes sure the adapter and network are functioning
properly. If Setup finds a problem, it displays the results and some
possible solutions.
5
6
When Setup finishes the tests, you’ll see the Install Network Drivers
screen.
Select the driver you want to install. Setup can install a NetWare client
driver for you. If you’re installing other drivers, Setup displays a
README file with installation instructions.
!
Troubleshooting
If you can’t connect to a server, first try the suggestions here, then turn to
page 14.
•
Make sure you’re using the drivers for this adapter. The driver filename
contains the letter B (for example, E100BODI.COM).
•
If you’re replacing an existing adapter, make sure the LINK statement in
your NET.CFG is correct for the new adapter. For example, the LINK
statement for a NetWare client should be:
LINK DRIVER E100BODI
•
•
•
Verify that the frame type in your NET.CFG file matches your network.
If setting up a server, check your LOAD and BIND statements.
Test the adapter by running diagnostics in Setup. Additional testing is
available by using a responder (see below).
•
Check the README files (see page 1 for instructions).
Responder testing on the network (optional)
Setup can test the adapter more thoroughly if you have a responder on the
network while running the tests.
1
2
3
Go to a computer on the network with any EtherExpress adapter installed
(except EtherExpress 32 or EtherExpress 16 MCA).
Run the appropriate configuration program for the installed adapter and
set it up as a responder.
Return to the computer with the new adapter. Run Setup and make the
new adapter a sender. Test the adapter.
5
Windows NT Server or Workstation
Automatic configuration
1
PCI computers automatically detect and configure PCI-compliant adapters
while booting. The PRO/100B TX PCI adapter IRQ level and I/O address are
automatically set by the BIOS each time you start your computer.
Start your computer to automatically configure the adapter. Configuration is
complete when Windows NT starts or the DOS prompt appears.
If your computer displays an error while booting, it may require additional
steps to configure. See the PCI Installation Tips section on page 17 for more
information.
2
Install network drivers - Windows NT Version 4.0 only
After putting the adapter in the computer and starting Windows NT, you need
to install the Intel drivers. Have the Windows NT CD-ROM disk available for
this procedure.
If you are installing Windows NT 4.0 at this time, click the Start
Search button when the network adapter installation window
NOTE:
appears. This allows NT to auto-detect the adapter (as the “Intel
82557-based 10/100 Ethernet Adapter”). You may then skip steps
1 - 4 below.
1
2
3
4
Double-click the Network icon in the Control Panel.
Click the Adapters tab in the window that appears.
Click Add. A list of adapter appears.
Select the “Intel EtherExpress PRO/100B PCI Adapter” and click OK.
The required Intel drivers and the Intel PROSet utility are installed.
PROSet displays the following window.
6
PROSet is an enhanced utility that you can use to easily configure and
test your adapter in Windows NT. PROSet also displays the computer
resources that were assigned to each PRO adapter installed.
5
6
Click OK in the main PROSet window to return to Windows NT.
The Intel adapter now appears as the “Intel 82557-based 10/100 Ethernet
Adapter” on the list in the Network window. Click Close to finish.
7
Restart Windows NT when prompted.
To install multiple adapters, repeat this procedure for each new adapter. See
page 11 for specific information.
To run the PROSet software at any time, double-click the Intel
PROSet icon in the Control Panel or click the Adapter Properties
button.
Install network drivers - Windows NT Version 3.5x only.
After putting the adapter in the computer and starting Windows NT, you need
to install the Intel drivers and test the adapter.
1
2
3
Double-click the Network icon in the Control Panel.
Click Add Adapter.
When the list of adapters appears, scroll to the end of the list and select
<Other> Requires disk from manufacturer.
4
Insert the Intel Configuration and Drivers disk in the A: drive and click
OK. Drivers and the Intel PROSet utility are installed and PROSet starts.
PROSet is an enhanced utility that you can use to easily configure and
test your adapter in Windows NT. PROSet also displays the computer
resources that were assigned to each PRO adapter installed. The PROSet
main window is shown on the preceding page.
5
6
Click OK in the PROSet main window to return to Windows NT.
Click OK in the Network Settings dialog box and remove the installation
disk. When prompted, restart Windows NT.
To install multiple adapters, repeat this procedure for each new adapter.
See page 11 for specific information.
To run the PROSet software at any time, double-click the Intel
PROSet icon in the Control Panel.
7
Troubleshooting
!
If Windows NT reports an error or you can’t connect to the network, try the
suggestions here first, then turn to page 14 if necessary.
•
Make sure you’re using the drivers for this adapter. Drivers are located
on the Windows NT CD-ROM or on the Intel Drivers and Configuration
disk version 2.3 or later.
•
Make sure the driver is loaded and the protocols are bound. Check the
Network Bindings dialog box in Windows NT.
•
•
Check the Windows NT Event Viewer for error messages.
If you are attaching to a NetWare network, check your frame type and
verify that NetWare client software has been installed.
•
Test the adapter with PROSet. After installing the adapter you can run
PROSet from your hard disk. To do this, double-click the Intel PROSet
icon in the Control Panel. Click Test to run diagnostics. For additional
information, click Help in the PROSet window.
•
Check with your LAN administrator — you may need to install
supplemental networking software.
Windows 95
1
Automatic Configuration
PCI computers automatically detect and configure PCI-compliant adapters
while booting. The PRO/100B TX PCI adapter IRQ level and I/O address are
automatically set by the BIOS each time you start your computer.
Start your computer to automatically configure the adapter. Configuration is
complete when Windows 95 starts.
If your computer displays an error while booting, it may require additional
steps to configure. See the PCI installation tips section on page 17 for more
information.
2
Install Network Drivers from Diskette
Have your Windows 95 installation CD-ROM or disks available, as Windows
95 prompts for them when you install the new adapter.
1
After you put the adapter in the computer, start Windows 95.
The New Hardware Found dialog box appears. If this box does not
appear and Windows 95 starts normally, you may need to manually add
the adapter. See page 10.
2
3
Click “Driver from disk provided by hardware manufacturer,” then click
OK. The Install From Disk dialog box appears.
Insert the Intel Configuration and Drivers disk.
8
4
5
Specify A:\(or B:\) as the path, then click OK.
Follow prompts for any Windows 95 installation disks and restart when
prompted. (If you installed from CD-ROM, the installation files are
typically located at D:\Win95, where D is your CD-ROM drive.)
After restarting Windows 95, you should be able to connect to your network
by double-clicking the Network Neighboorhood.
Install PROSet Software
3
PROSet is an enhanced Intel utility that you can use to easily configure and
test your adapter in Windows 95. PROSet also displays the computer
resources that were assigned to each PRO adapter installed. To install
PROSet:
1
2
Insert the Intel Configuration and Drivers disk.
From My Computer or the Windows Explorer, double-click the 3½
Floppy disk icon.
3
Click the “Proset” icon or filename and click the right mouse button.
From the menu that appears, click Install.
4
5
The PROSet files are copied to your hard disk.
Start PROSet by double-clicking on the Intel PROSet icon in the Control
Panel:
6
The PROSet software examines your computer and displays the window
shown here.
7
Click OK to exit PROSet and return to Windows 95.
9
Manually Adding an Adapter
If the New Hardware Found dialog box does not appear at startup and you
cannot connect to the network, check the Device Manager list to see if the
new adapter is present. If it is not, use the following procedure.
1
2
3
4
5
6
7
From the Control Panel, double click the System icon.
Click the Device Manager tab in the window that appears.
Double-click Other Devices (question mark icon) in the list area.
Double-click PCI Ethernet Controller.
Click the Driver tab, then click Change Driver.
Select Network Adapters and click OK.
Click Have Disk from the window that appears. Insert the Intel
Configuration and Drivers Disk and click OK.
8
Follow any prompts for Windows 95 installation disks and restart when
prompted.
Troubleshooting
!
If you can’t connect to a server or if Windows 95 reports an error after you
double-click Network Neighborhood, try the suggestions here first, then turn
to page 14 if necessary.
•
•
•
•
Make sure you’re using the drivers that are on the drivers diskette that
ships with this adapter.
Make sure the driver is loaded and the protocols are bound. Check
Device Properties list for trouble indicators (an X or ! symbol).
Test the adapter. Start PROSet (see page 9) and click Test to run
diagnostics.
Check with your LAN administrator — you may need to install
supplemental networking software.
NetWare Server, Client 32, UNIX, OS/2,
Banyan, and Other Operating Systems
For these, refer to our online documents. On a DOS computer, view the
appropriate README file for information on installing your network driver.
To view the README files, insert the Intel Configuration
Readme
Files
and Drivers disk into a drive, switch to that drive, and type:
SETUP /README E
Look through the selection called “Installing EtherExpress PRO/100B TX
PCI Adapter Drivers” for the operating system you need.
10
Installing Multiple Adapters
All users: The adapter’s 12-digit, hexadecimal Ethernet address is on a
sticker near the edge of the adapter. The Ethernet address is sometimes called
the node address or the MAC address. Note that the PCI slot number may not
correspond with the physical connector in your computer.
NetWare users: The server drivers use the PCI slot number to identify each
installed adapter. You can correlate the PCI slot number to the adapter by
using the Ethernet address that is printed on a label on the adapter. Run Setup
from the Intel disk to view the Ethernet address and slot number for each
installed adapter. For more information, see the README files. NetWare 4.11
server installations use unique slot numbers that are assigned during sever
setup.
Windows NT and Windows 95 users: Repeat the configuration procedure
for each adapter you want to install (add only one adapter at a time). While
PROSet can detect all the PRO/100B adapters in your computer, you still
need to perform the configuration process on each adapter. In Windows NT,
be sure to click the Show all PRO Adapters box in the Configuration window.
See the README file for more information.
Select Duplex Mode (optional)
Duplexing is a performance option that lets you choose how the adapter sends
and receives data packets over the network. The PRO/100B TX adapter can
operate at full duplex only when connected to a full duplex 10BASE-T or
100BASE-TX switching hub. To summarize:
•
Auto (requires a full duplex switching hub with auto-negotiation
capability). The adapter negotiates with the hub to send and receive
packets at the highest rate. This is the default setting. If the hub does not
provide auto-negotiation, the adapter runs at half duplex.
•
Full duplex (requires a full duplex switching hub). The adapter can
send and receive packets at the same time. This mode can increase
adapter performance capability. If the full duplex hub provides auto-
negotiation, the adapter runs at full duplex. If the full duplex hub does
not provide auto-negotiation, you need to set the adapter duplex mode
manually (see following paragraphs)
•
Half duplex. The adapter performs one operation at a time; it either
sends or receives.
NOTE:
If your hub is running at 100 Mbps and half duplex, your potential
bandwidth is higher than if you run at 10 Mbps and full duplex.
11
Manually Configuring for Full Duplex
If your switch supports auto-negotiation with the N-way standard, duplex
configuration is automatic and no action is required on your part. However,
few switches in the current installed base support auto-negotiation. Check
with your network system administrator to verify. Most installations will
require manual configuration to change to full duplex.
Configuration is specific to the driver you’re loading for your network
operating system (NOS), as shown in the following paragraphs.
To set up the duplex mode, refer to the section below that corresponds to your
operating system.
Adapter performance may suffer or your adapter may not operate
NOTE:
if your hub does not support full duplex and you configure the
adapter to full duplex. Leave the adapter on half duplex if you are
not sure what type of hub you are connected to.
DOS ODI, NDIS 2.01 Clients
Edit the NET.CFG or PROTOCOL.INI file. Add to Link Driver section:
FORCEDUPLEX 2
SPEED 100 (or 10 if 10BASE-T)
NetWare server
In AUTOEXEC.NCF, Load E100B.LAN and add the following statement
(you must include the equal sign for servers):
FORCEDUPLEX=2
SPEED=100 (or 10 if 10BASE-T)
For more information, see the README file for NetWare servers.
Windows NT
While running Windows NT:
1
2
From the Control Panel, double-click the Intel PROSet icon.
PROSet examines your system and displays the Adapter Setup
window.
If you have multiple adapters, click the “Show All Adapters” box
and then select the adapter you are configuring (you can identify it
by its Ethernet address). Each adapter must be configured
separately. See page 11, Installing Multiple Adapters, for more
information.
3
4
From the window that appears, click Change.
From the Adapter Setup window, click the menu for Network Speed.
12
5
6
7
8
9
Click 100 or 10 Mbps, depending on hub speed.
Click the menu for Duplex Mode
Click Full.
Click OK when finished.
Click Restart Windows NT.
Windows 95
While running Windows 95:
1
2
From the Control Panel, double-click the Intel PROSet icon.
PROSet examines your system and displays the Adapter Setup
window. If you have multiple adapters, click the adapter you are
configuring (you can identify it by its Ethernet address). Each
adapter must be configured separately. See page 11, Installing
Multiple Adapters, for more information.
3
4
5
6
7
8
9
From the window that appears, click Change.
From the Adapter Setup window, click the menu for Network Speed.
Click 100 or 10 Mbps, depending on hub speed.
Click the menu for Duplex Mode
Click Full.
Click OK when finished.
Click OK to restart Windows 95.
Other operating systems
See the Adapter Installation and Special Configurations README file. See
page 1 for instructions on viewing README files.
“Push” Installation for Windows 95
If you are a LAN Administrator setting up server-based push installation of
Windows 95 as defined in Microsoft Windows 95 Resource Kit, additional
steps are required for this adapter. Refer to the Windows 95 README file
under the Microsoft section of Installing EtherExpress PRO/100B adapter
drivers.
13
Troubleshooting
If the adapter can’t connect to the network
Make sure the cable is installed properly.
The network cable must be securely attached at both RJ-45 connections
(adapter and hub). If the cable is attached but the problem persists, try a
different cable. The maximum allowable distance from adapter to hub is 100
meters.
If you’re directly connecting two computers (no hub), use a crossover cable.
Most hubs require a straight-through cable, while most switches require a
crossover cable (see your hub or switch documentation to verify).
See the Cabling Information README file for more information on cross-
over cables.
Check the LED lights on the adapter.
The EtherExpress PRO/100 TX PCI adapter has three diagnostic LEDs above
the cable connector. These lights help indicate if there’s a problem with the
connector, cable, or hub. The table on the next page describes the LEDs.
Link LED
Activity LED
100 Mbps LED
LNK
ACT
100
TX
DATA
PC-3409a
14
LED
Indication
Meaning
LNK
On
The adapter and hub are receiving power;
the cable connection between the hub and
adapter is good.
Off
The adapter and hub are not receiving
power; the cable connection between the
hub and adapter is faulty; or you have a
driver configuration problem.
ACT
100
On or flashing
Off
The adapter is sending or receiving
network data. The frequency of the flashes
varies with the amount of network traffic.
The adapter is not sending or receiving
network data.
On
Off
Operating at 100 Mbps.
Operating at 10 Mbps.
Make sure you’re using the correct drivers.
Make sure you’re using the drivers that come with this adapter. The driver
filename contains the letter B (for example, E100BODI.DOS). Drivers that
support previous versions of the EtherExpress PRO/100 PCI adapter do not
support this version of the adapter.
Make sure the hub port and the adapter have the same
duplex setting.
If you configured the adapter for full duplex, make sure the hub port is also
configured for full duplex. Setting the wrong duplex mode can degrade
performance, cause data loss, or result in lost connections.
Testing the adapter
Test the adapter by running Intel diagnostics. For DOS or Windows 3.1
computers, run Setup on the Intel Drivers and Configuration disk. For
Windows NT and Windows 95 run Intel PROSet by double-clicking the Intel
PROSet Icon in the Control Panel. Click Help from the main PROSet window
to get complete diagnostics information and instructions.
Common problems and solutions
SETUP.EXE reports the adapter is “Not enabled by BIOS”.
• The PCI BIOS isn’t configuring the adapter correctly. Try the PCI
installation tips on page 17.
15
The computer hangs when the drivers are loaded.
• Change the PCI BIOS interrupt settings. See the next page for PCI
installation tips.
• If you are using EMM386, it must be version 4.49 or newer (this version
ships with MS-DOS 6.22 or newer).
Diagnostics pass, but the connection fails or errors occur.
• Make sure you are using category 5 wiring and the network cable is
securely attached.
• For NetWare clients, make sure you specify the correct frame type in your
NET.CFG file.
• Make sure the duplex mode setting on the adapter matches the setting on
the hub.
• At 100 Mbps, connect to a 100BASE-TX hub only (not T4).
The LNK LED doesn’t light.
• Make sure you’ve loaded the network drivers.
• Check all connections at the adapter and the hub.
• Try another port on the hub.
• Make sure the duplex mode setting on the adapter matches the setting on
the hub.
• Make sure you have the correct type of cable between the adapter and the
hub. 100 BASE-TX requires four pairs. Some hubs require a crossover
cable while others require a straight-through cable. See the Cabling
README file for more information on cabling.
The ACT LED doesn’t light.
• Make sure you’ve loaded the correct network drivers.
• The network may be idle. Try accessing a server.
• The adapter isn’t transmitting or receiving data. Try another adapter.
• May not be using four-pair cable for TX wiring.
The adapter stopped working when another adapter was added to the
computer.
• Make sure the cable is connected to the EtherExpress PRO/100 TX PCI
adapter.
• Make sure your PCI BIOS is current. See page 17 for PCI installation tips.
• Make sure the other adapter supports shared interrupts. Also, make sure
your operating system supports shared interrupts — OS/2* doesn’t.
• Try reseating the newest adapter.
The adapter stopped working without apparent cause.
• Try reseating the adapter first, then try a different slot if necessary.
• The network driver files may be corrupt or deleted. Delete and then
reinstall the drivers.
• Try a different PRO/100 TX PCI adapter.
• Run the diagnostics.
16
Technical Information
PCI Installation Tips
PCI computers are designed to automatically configure add-in cards each time
the computer starts. Your PCI computer sets the I/O address and IRQ level for
your Intel network adapter when the computer starts. These values cannot be
changed by Intel adapter software. If you experience a problem when the
computer starts, additional configuration steps may be required.
On these computers, manual configuration is possible through the computer’s
PCI BIOS setup utility. Refer to your computer’s documentation. You may
need to verify or change some BIOS settings.
Some common PCI solutions are listed here.
•
Busmaster enabled slots. On some computers, all slots are not
busmaster enabled by default. Check your BIOS PCI bus setting. It will
set to either Busmaster or Non-busmastered. Choose Busmaster.
•
Reserve interrupts (IRQs) and/or memory addresses for ISA
adapters. This prevents PCI cards from trying to use the same settings
ISA cards are using. Check your PCI BIOS setup program. There may be
IRQ options such as ‘Enable for ISA,’ ‘Reserve for ISA,’ or ‘Disable for
PCI.’ This option is sometimes in the Plug and Play area of the BIOS
setup.
•
•
Enable the PCI slot. In some PCI computers, you must use the PCI
BIOS setup program to enable the PCI slot. This is especially common in
PCI computers with the Phoenix BIOS.
Update your PCI BIOS. An updated PCI system BIOS can correct some
PCI configuration problems. Call your computer manufacturer to see if
an updated BIOS version is available for your computer. Phone numbers
for the top PCI computer manufacturers are listed in the PCI Installation
README file on the Intel Configuration and Drivers disk.
•
Configure the slot for level-triggered interrupts. The slot the adapter
is using must be configured for level-triggered interrupts rather than
edge-triggered interrupts. Check your PCI BIOS Setup program.
Here are some example PCI BIOS setup program parameters:
PCI slot #:
Master:
Slave:
Slot where the adapter is installed
ENABLED
ENABLED
Latency timer: 40
Interrupt:
Edge-level:
Choose an IRQ from the list
Level
The exact wording of these parameters varies with different computers.
17
Fast Ethernet Wiring
100BASE-TX Specification: The 100BASE-TX specification supports 100
Mbps transmission over two pairs of category 5 twisted-pair Ethernet (TPE)
wiring. One pair is for transmit operations and the other for receive
operations. Segment lengths are limited to 100 meters with 100BASE-TX for
signal timing reasons. This complies with the EIA 568B wiring standard.
Fast Ethernet Hubs and Switches
The two basic types of hubs are shared hubs and switching hubs. Ether-
Express PRO/100 TX adapters can be used with either type of hub for 10
Mbps. At 100 Mbps, a TX hub or switch is required.
Shared hubs
In a shared network environment, computers are connected to hubs called
repeaters. All ports of the repeater hub share a fixed amount of bandwidth, or
data capacity. On a 100 Mbps shared hub, all nodes on the hub must share the
100 Mbps of bandwidth. As stations are added to the hub, the effective band-
width available to any individual station gets smaller. Shared hubs do not
support full duplex.
Think of a shared repeater hub as a single-lane highway that everyone shares.
As the number of vehicles on the highway increases, the traffic becomes con-
gested and transit time increases for individual cars.
On a shared hub all nodes must operate at the same speed, either 10 Mbps or
100 Mbps. Fast Ethernet repeaters provide 100 Mbps of available bandwidth,
ten times more than what’s available with a 10BASE-T repeater.
Repeaters use a well-established, uncomplicated design, making them highly
cost effective for connecting PCs within a workgroup. These are the most
common type of Ethernet hubs in the installed base.
Switching hubs
In a switched network environment, each port gets a fixed, dedicated amount
of bandwidth. In the highway scenario, each car has its own lane on a multi-
lane highway and there is no sharing.
In a switched environment, data is sent only to the port that leads to the pro-
per destination station. Network bandwidth is not shared among all stations,
and each new station added to the hub gets access to the full bandwidth of the
network.
If a new user is added to a 100 Mbps switching hub, the new station receives
its own dedicated 100 Mbps link and doesn’t impact the 100 Mbps bandwidth
of another station. Switching hubs can effectively increase the overall
bandwidth available on the network, significantly improving performance.
Switching hubs can also support full duplex.
For more information on Fast Ethernet, visit our Network Products
website (see page 1).
18
Network software license agreement
BY USING THIS SOFTWARE, YOU ARE AGREEING TO BE BOUND BY THE TERMS OF THIS
AGREEMENT. DO NOT USE THIS SOFTWARE UNTIL YOU HAVE CAREFULLY READ AND AGREED TO
THE FOLLOWING TERMS AND CONDITIONS. IF YOU DO NOT AGREE TO THE TERMS OF THIS
AGREEMENT, PROMPTLY RETURN THE SOFTWARE PACKAGE AND ANY ACCOMPANYING ITEMS.
LICENSE: Intel Corporation (“Intel”) grants you the non-exclusive right to use the enclosed software program
(the “Software”). You will not use, copy, modify, rent, sell or transfer the Software or any portion thereof except as
provided in this Agreement.
You may:
1. Install/use the Software on a single computer or on a single local area network (“LAN”) server;
2. Copy the Software solely for backup or archival purposes, including copying the Software into memory.
RESTRICTIONS:
You Will Not:
1. Sublicense the Software;
2. Reverse engineer, decompile, or disassemble the Software;
3. Copy the Software, in whole or in part, except as provided in this Agreement.
TRANSFER: You may transfer the Software to another party if the receiving party agrees to the terms of this
Agreement and you retain no copies of the Software and accompanying documentation. Transfer of the Software
terminates your right to use the Software.
OWNERSHIP AND COPYRIGHT OF SOFTWARE: Title to the Software and all copies thereof remain with
Intel or its vendors. The Software is copyrighted and is protected by United States and international copyright
laws. You will not remove the copyright notice from the Software. You agree to prevent any unauthorized copying
of the Software.
DUAL MEDIA SOFTWARE: If the Software package contains multiple media, you may only use the disks
appropriate for your single-user computer or LAN.
WARRANTY: Intel warrants that it has the right to license you to use the Software. The Software is provided “AS
IS.” Intel warrants that the media on which the Software is furnished will be free from defects in material and
workmanship for a period of one (1) year from the date of purchase. Upon return of such defective media, Intel’s
entire liability and your exclusive remedy shall be the replacement of the Software.
THE ABOVE WARRANTIES ARE THE ONLY WARRANTIES OF ANY KIND EITHER EXPRESS OR
IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY
PARTICULAR PURPOSE.
LIMITATION OF LIABILITY: NEITHER INTEL NOR ITS VENDORS SHALL BE LIABLE FOR ANY
LOSS OF PROFITS, LOSS OF USE, LOSS OF DATA, INTERRUPTIONS OF BUSINESS, NOR FOR
INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND WHETHER
UNDER THIS AGREEMENT OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
AUDIT: Intel reserves the right to have audits conducted to verify your compliance with this Agreement.
TERMINATION OF THIS LICENSE: Intel may terminate this license at any time if you are in breach of any of
its terms and conditions. Upon termination, you will immediately destroy the Software or return all copies of the
Software and documentation to Intel.
U.S. GOVERNMENT RESTRICTED RIGHTS: The Software and documentation were developed at private
expense and are provided with “RESTRICTED RIGHTS.” Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in FAR 52.227-14 and DFAR 252.227-7013 et seq. or its successor.
EXPORT LAWS: You agree that the distribution and export/re-export of the Software is in compliance with the
laws, regulations, orders or other restrictions of the U.S. Export Administration Regulations.
APPLICABLE LAW: This Agreement is governed by the laws of the State of California and the United States,
including patent and copyright laws. Any claim arising out of this Agreement will be brought in Santa Clara
County, California.
19
Limited lifetime hardware warranty
Intel warrants to the original owner that the hardware product delivered in this package will be free from defects in
material and workmanship. This warranty does not cover the product if it is damaged in the process of being
installed or improperly used.
THE ABOVE WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, WHETHER EXPRESS, IMPLIED OR
STATUTORY, INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE ARISING OUT OF ANY PROPOSAL, SPECIFICATION, OR SAMPLE.
This warranty does not cover replacement of adapter products damaged by abuse, accident, misuse, neglect,
alteration, repair, disaster, improper installation, or improper testing. If the product is found to be defective, Intel,
at its option, will replace or repair the product at no charge except as set forth below, or refund your purchase price
provided that you deliver the product along with a Return Material Authorization (RMA) number (see below),
along with proof of purchase (if not registered), either to the dealer from whom you purchased it or to Intel with an
explanation of any deficiency. If you ship the product, you must assume the risk of damage or loss in transit. You
must use the original container (or the equivalent) and pay the shipping charge.
Intel may replace or repair the adapter product with either new or reconditioned parts, and any part or product
replaced becomes Intel’s property. Repaired or replaced products will be returned at the same revision level as
received or higher, at Intel’s option. Intel reserves the right to replace discontinued product with an equivalent
current generation product.
Returning a defective product
From North America:
Before returning any product, contact Intel Customer Support and obtain a Return Material Authorization (RMA)
number by calling +1 503 264-7000.
If the Customer Support Group verifies that the product is defective, they will have the RMA department issue you
an RMA number to place on the outer package of the product. Intel cannot accept any product without an RMA
number on the package.
All other locations:
Return the product to the place of purchase for a refund or replacement.
INTEL ADAPTER MONEY-BACK GUARANTEE (North America Only)
Intel wants you to be completely satisfied with the Intel adapter product that you have purchased. Any time within
ninety (90) days of purchase, you may return your Intel adapter to the original place of purchase for a full refund
of the purchase price from your dealer. Resellers and distributors, respectively, accepting returns and refunding
money back to their customers may return Intel adapters to their original place of purchase. Intel guarantees that it
will accept returns under this policy and refund the original purchase price to customers purchasing directly from
Intel.
Limitation of Liability and Remedies
INTEL SHALL HAVE NO LIABILITY FOR ANY INDIRECT, SPECULATIVE, CONSEQUENTIAL,
INCIDENTAL, PUNITIVE OR SPECIAL DAMAGES ARISING FROM THE USE OF OR INABILITY TO USE
THIS PRODUCT INCLUDING, WITHOUT LIMITATION, LOSS OF USE, BUSINESS INTERRUPTIONS,
LOSS OF PROFITS, AND LOSS OF GOODWILL, WHETHER ANY SUCH DAMAGES ARISE OUT OF
CONTRACT NEGLIGENCE, TORT, OR UNDER ANY WARRANTY, IRRESPECTIVE OF WHETHER INTEL
HAS ADVANCE NOTICE OF THE POSSIBILITY OF ANY SUCH DAMAGES. NOTWITHSTANDING THE
FOREGOING, INTEL’S TOTAL LIABILITY FOR ALL CLAIMS UNDER THIS AGREEMENT SHALL NOT
EXCEED THE PRICE PAID FOR THE PRODUCT. THESE LIMITATIONS ON POTENTIAL LIABILITIES
WERE AN ESSENTIAL ELEMENT IN SETTING THE PRODUCT PRICE. INTEL NEITHER ASSUMES NOR
AUTHORIZES ANYONE TO ASSUME FOR IT ANY OTHER LIABILITIES.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitations may not apply to you.
Software provided with the hardware product is not covered under the hardware warranty described above. See the
applicable software license agreement which shipped with the adapter product for details on any software
warranty.
April 28, 1994
20
FCC compliance statement
This product has been tested and found to comply with the limits for a Class B computing device pursuant to Part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. Installed correctly, it probably will not interfere with radio or TV reception. However, we
do not guarantee the absence of interference.
This product generates and uses energy of about the same frequency as radio and TV broadcasts. Installed
incorrectly, it may interfere with reception of radio and TV broadcasts.
If you suspect this product is causing interference, turn your computer on and off while the radio or TV is showing
interference. If the interference disappears when you turn the computer off and reappears when you turn the
computer on, something in the computer is causing interference.
To reduce interference, try these suggestions:
•
•
Change the direction of the radio or TV antenna.
Move the computer, radio or TV. For example, if the computer is to the right of the TV, move it to the left of the
TV. Or move them farther apart.
•
•
Plug the computer into a different electrical outlet than the radio or TV.
Ensure that all expansion slots (on the back or side of the computer) are covered. Also ensure that all metal
retaining brackets are tightly attached to the computer.
NOTE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
CAUTION
If the device is changed or modified without permission from Intel, the user may void his or her authority to
operate the equipment.
Canadian compliance (Industry Canada)
When tested in at least one intended host:
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in
the interference-causing equipment standard entitled “Digital Apparatus”, ICES-003 of the Canadian Department
of Communications.
Cet appareil numérique respecte les limites bruits radioélectriques applicables aux appareils numériques de Class
B prescrites dans la norme sur le matériel brouilleur: “Appareils Numériques”, NMB-003 édictée par le Ministre
Canadien des Communications.
Manufacturer declaration
This certifies that EtherExpress PRO/100 TX PCI adapters comply with the EU Directive 89/336/EEC, using the
EMC standards EN55022 (Class B) and EN50082-1. This product also meets or exceeds EN60950 safety
requirements.
This product has been tested and verified to meet CISPR 22 Class B requirements.
Intel Corporation
Network Products Division MS JF3-408
2111 N.E. 25th Ave.
Hillsboro, Oregon 97124
21
643998-004
|