Intel Network Router PRO 100 User Manual

™

Intel EtherExpress PRO/100

LAN+Modem56 PC Card

User’s Guide

How to Use This Manual

This User’s Guide contains the latest information on the EtherExpress

PRO/100 LAN+Modem56 PC Card available at press time. It is designed

to help both new and experienced users with installation and configura-

tion.

Installation and Configuration Overview

For an overview, see the Quick Installation Card. For complete technical

details and troubleshooting information, see the chapter covering your

operating system (Chapter 2 Windows 95, Chapter 3 Windows NT, or

Chapter 4 Windows 3.x/MS-DOS) in this User’s Guide.

How to Find More Information

Use the Table of Contents, Index, and page and text headings in this User’s

Guide to help you find what you need. Check the README file on Disk 2,

Network Drivers disk. To check for updated drivers, visit our Customer

Support web site at:

http://support.intel.com

See Appendix A for additional support information.

Contents

Hardware Installation ..................................... 1-1

Software Supplied ................................................................... 1-2

Hardware Installation .............................................................. 1-3

Unpacking and Inspection ....................................................... 1-3

Other Required Equipment ..................................................... 1-4

Installing Card and Cables ...................................................... 1-5

PRO/100 Modem and Ethernet Connections.......................... 1-6

Windows* 95 Installation ............................... 2-1

Which Version of Windows 95? ............................................... 2-1

How Can I Tell Which Version I Have? .................................... 2-1

Additional Information in this Chapter ..................................... 2-2

Windows 95 Installation (Retail Version) ................................. 2-2

Windows 95 OSR2 Installation

(OEM Version) .................................................................. 2-4

How to Install for Windows 95 and NetWare* ......................... 2-8

Utilities..................................................................................... 2-8

Power-Saving Modes .............................................................. 2-9

Windows 95 Troubleshooting .................................................. 2-9

Troubleshooting Checklist ..................................................... 2-10

Windows 95 Driver Parameters Reference ........................... 2-13

Windows NT Installation................................ 3-1

Which Version of Windows NT? .............................................. 3-1

How Can I Tell Which Version and Service Pack I Have? ....... 3-2

Additional Information in this Chapter ..................................... 3-2

Windows NT 4.0 Installation.................................................... 3-3

Windows NT 3.51 Installation.................................................. 3-5

Power-Saving Modes .............................................................. 3-7

Utilities..................................................................................... 3-7

Windows NT Driver Parameters Reference ............................ 3-8

Windows 3.x/DOS Installation....................... 4-1

Installation under MS-DOS ..................................................... 4-2

Windows 3.x Modem Driver Settings .................................... 4-36

Windows 3.x Network Driver Parameters ............................. 4-37

ODI Settings (for M16BODI.COM) ........................................ 4-38

Error Messages for Windows 3.x and MS-DOS Drivers ....... 4-47

iv PRO/100 LAN+Modem PC Card User's Guide

Windows 3.x Troubleshooting................................................ 4-51

Computer-Specific Application Notes (Windows 3.x)............ 4-60

Utilities and Applications .............................. 5-1

Utilities..................................................................................... 5-1

Country Identifier Utility........................................................... 5-1

Modem Test Utility ................................................................... 5-2

Diagnostic Test Utility (M16BTEST.EXE) ................................ 5-3

COM port monitor (Windows 3.x only) .................................... 5-5

Communications Application Notes and Modem

Script Files ...................................................................... 5-6

Modem Reference .......................................... 6-1

Result Codes........................................................................... 6-1

AT Command Reference ......................................................... 6-4

S-Register Reference............................................................ 6-25

Automated Customer Support ..................... A-1

Specifications ................................................ B-1

Limited Warranty ........................................... C-1

Agency Notices ............................................. D-1

Software License Agreement ........................E-1

Index .........................................................Index-1

CHAPTER 1

Hardware Installation

Introduction

The PRO/100 PC Card is the ideal high-speed, multifunction solution for

portable PC users. It supports 10 and 100Mbps Ethernet networks and

modem speeds up to 56Kbps for high-performance connectivity in any

environment. The PRO/100 PC Card plugs into your computer’s Type II

PC Card slot for simultaneous connection to an Ethernet LAN and the

telephone network.

56K Technology

The PRO/100 PC Card uses K56flex* modem technology to reach speeds

up to 56Kbps. K56flex Technology enables notebook users to access

information and E-mail on corporate networks, the Internet and other

online services at speeds up to 56Kbps over standard phone lines.

These higher speeds are achieved by avoiding conversion from digital to

analog lines in the connection between the user and service provider.

Ordinary connections begin over an analog line, are converted to digital

by the phone company and are converted back to analog in the final

segment before arriving at the service provider. In order to achieve 56K

connections, there can only be one digital to analog conversion. This

requires the service provider to have a direct digital connection and

therefore, avoids one conversion of the signal. By avoiding this conver-

sion, data download speeds up to 56K are possible. Data sent upstream by

the user travels at the standard V.34 rate. Also, the modems at both ends

of the call must be compatible to achieve speeds up to 56K. If the

modems at both ends of the call are not compatible, they will negotiate a

standard V.34 connection.

1-2 PRO/100 LAN+Modem PC Card User’s Guide

With K56flex technology, current country-specific regulations may limit

download speeds. Additional factors such as phone line conditions, can

affect the performance of the PRO/100 PC Card. You can find more

detailed technical information on K56flex performance on Intel's support

web site, support.intel.com.

Model

MBLA1656

Combination card that provides access to

10Base-T and 100Base-TX networks and

modem speeds up to 56Kbps. An Ethernet

Adapter Cable (RJ-45) and Modem Cable

(RJ-11) are supplied. It provides access to

both 10Mbps and 100Mbps networks with a

single Ethernet Adapter Cable, and auto-

senses 10Mbps or 100Mbps network speed.

Requires Category 5 (data grade)

unshielded twisted pair (UTP) cabling

for 100Mbps network connections.

Software Supplied

Intel drivers and other software are supplied on 3.5-inch 1.44 megabyte

disks. All popular network operating systems, including NetWare, Win-

dows 95, Windows NT, Windows 3.x, and Windows for Workgroups are

supported.

An easy-to-use Installation Program for Windows 3.x is provided on the

Intel Installation Disk, which includes the country identifier utility for local

modem settings.

Additional Features

The PRO/100 PC Card is a Type II PC Card conforming to the Personal

Computer Memory Card International Association (PCMCIA) PC Card

Standard. It supports HotSwap, suspend/resume power management, full-

duplex transmission at 10Mbps, and Advanced Look-Ahead Pipelining.

Hardware Installation 1-3

HotSwap

This card supports HotSwap on a PC Card computer that is running

Microsoft Windows 95 or Windows 3.x/MS-DOS using Card and Socket

Services. This feature allows the PRO/100 PC Card to be removed from

the computer, temporarily replaced with another type of PC card, then

reinserted without loss of the local area network connection.

Power Management Suspend/Resume

Power management features such as suspend/resume are supported by the

PRO/100 PC Card on PCMCIA systems running Windows 95 or Win-

dows NT, or Windows 3.x/MS-DOS using Card and Socket Services. This

means that when the computer enters a reduced power or power saving

mode, an ongoing local area network connection will remain active for the

period of time allowed by the network operating system

Hardware Installation

Note

Hardware installation requirements may vary with different

operating systems. For example, if your system is configured for

automatic detection of the card (for example, under Windows

95), the computer should be ON and standard operating

software loaded when the card is inserted. For installation

instructions specific to your particular environment, see the

appropriate chapter: Chapter 2. Installation with Windows 95,

Chapter 3. Installation with Windows NT, and Chapter 4.

Installation with Windows 3.x/MS-DOS.

The PRO/100 PC Card is compatible with Type II PC Card slots. The

hardware installation procedures outlined here are typical. Installation and

removal procedures vary on different PC Card-capable computers and

under different operating systems.

Unpacking and Inspection

After opening the PRO/100 PC Card box, verify that all parts are included

and have not been damaged during transportation. Retain the packing

materials.

1-4 PRO/100 LAN+Modem PC Card User’s Guide

Package Contents

• EtherExpress™ PRO/100 LAN+Modem PC Card PC Card (Model

MBLA1656)

• Model MBLA-1656: Ethernet adapter cable with a 15-pin PC Card

connector at one end and female RJ-45 connector at the other for

10Base-T or 100Base-TX connectivity

• Modem cable with RJ-11 telephone connector

• Intel EtherExpress™ PRO/100 LAN+Modem PC Card User's

Guide

(this book)

• Intel EtherExpress™ PRO/100 LAN+Modem PC Card Quick

Start card

• Software on two 1.44 MB 3.5-inch diskettes

• Protective adapter case

• 6-foot telephone cable

• Product registration card

Other Required Equipment

1 For LAN operations: a local area network supporting 10 or

100Mbps Ethernet, as required, and a network operating system

supported by the PRO/100 PC Card.

Note

Since the PRO/100 PC Card automatically detects the speed of

the network to which it is connected, it may be safely connected

to either a 100Base-TX or 10Base-T network, as specified in

items 2 and 3 below.

2 For connection to a 100Base-TX Ethernet network, a Category 5

(data grade) unshielded twisted pair (UTP) network cable terminat-

ing in a male RJ-45 connector and connected to a 100Mbps hub or

switch.

3 For connection to a 10Base-T Ethernet network, a network cable

terminating in a male RJ-45 connector and connected to a 10Mbps

hub or switch.

Hardware Installation 1-5

4 For modem operations: an analog telephone line or PABX

connection (RJ-11), and if needed, an RJ-11 adapter for the local

telephone system.

Note

Do not connect to a digital telephone line or digital PABX

system. The hardware on the adapter will protect your modem

from inadvertent connection to a digital line.

Installing Card and Cables

Inserting the PRO/100 PC Card into the PC Card Slot

1 Grasp the PRO/100 PC Card by the edges with the Intel logo

facing upward and the 68-pin PC Card connector next to the card

slot.

2 Insert the card into the PC card slot and push it in until it is firmly

seated. If you have more than one PC card slot, the PRO/100 PC

Card will automatically detect which slot it is in.

Inserting the PRO/100 PC Card into the Computer.

1-6 PRO/100 LAN+Modem PC Card User’s Guide

Note

The PRO/100 PC Card may feel hot to the touch, after

prolonged periods of normal use in some environments. This is

normal and is not known to affect operation of the Intel card,

the host computer, or any other peripheral device. However, to

avoid discomfort, use caution when removing the card from your

computer after extended use (see your computer manual for

removal procedures).

PRO/100 Modem and Ethernet Connections

Connecting the Modem Cable to the PRO/100

• Hold the PC Card with the top (card label and network graphic)

facing you. Grasp the flat connector on the end of the Modem

Cable with the network graphic on top, and plug it in to the

matching receptacle on the right side of the PRO/100 PC Card.

The cable connector will click into place. Do not force the connec-

tion.

MODEM CABLE

Attaching the Modem Cable to the PRO/100.

Connecting the Modem Cable to the Telephone Line

• Plug one end of a male analog telephone line cable into the RJ-11

jack on the Modem Cable, and the other end into an analog (single-

line) RJ-11 telephone wall jack.

Hardware Installation 1-7

Caution

The PRO/100 PC Card will not work with digital telephone lines

or digital PABX systems. The adapter hardware will protect your

modem against damage from inadvertent connection to a digital

line.

TRANSMIT/RECEIVE

(YELLOW)

CARRIER

DETECT

(GREEN)

TELEPHONE

CABLE

MODEM CABLE

Connecting the Telephone Cable to the Modem Cable.

Connecting the Ethernet Adapter Cable to the PRO/100

• Hold the PC Card with the top facing upward. Grasp the flat

connector on the end of the Ethernet Adapter Cable with the

network graphic on top, and plug it in to the matching receptacle on

the left side of the PRO/100 PC Card. The cable connector will

click into place. Do not force the connection.

ETHERNET

ADAPTER CABLE

PC-3808

Attaching the Ethernet Adapter Cable to the PRO/100.

1-8 PRO/100 LAN+Modem PC Card User’s Guide

Connecting to a Twisted Pair network.

Caution

For safety reasons, do not interchange the telephone (RJ-11) and

Ethernet (RJ-45) cables by forcing the Ethernet cable into the

modem sloton the PRO/100 PC Card.

• Plug the male RJ-45 connector at the end of the network cable into

the female RJ-45 connector on the Ethernet Adapter Cable.

LAN ACTIVITY

(YELLOW)

LINK INTEGRITY

Orange = 100 Mbps

Green = 10 Mbps

RJ-45 TWISTED PAIR ETHERNET CONNECTOR

Connecting the Ethernet Adapter Cable to the Network.

CHAPTER 2

Windows 95 Installation

Which Version of Windows 95?

Two Versions and Two Installation Paths

Currently two versions of Windows 95 are available:

• The standard retail version (designated 4.00.950 or 4.00.950a)

• OEM Service Release Version 2 (designated 4.00.950b, also known

as OSR2)

Installation procedures are presented in two separate sections:

• Windows 95 Installation (Retail Version)

• Windows 95 OSR2 Installation (OEM Version)

How Can I Tell Which Version I Have?

1 In Windows 95, click Start, Settings, and Control Panel.

2 In Control Panel, double-click the System icon.

3 In the System Properties window, click the General tab (if not

already displayed) and view information under System.

• For Microsoft Windows 95 4.00.950 or 4.00.950a, follow the

installation instructions under the heading Windows 95 Installation

(Retail Version)

2-2 PRO/100 LAN+Modem PC Card User’s Guide

• For Microsoft Windows 95 4.00.950b, follow the installation

instructions under the heading Windows 95 OSR2 Installation

(OEM Version)

Additional Information in this Chapter

This chapter also contains the following Windows 95 information:

• How to Install for Windows 95 and NetWare

• Power Saving Modes

• Utilities

• Troubleshooting

• Driver Parameters Reference

Windows 95 Installation (Retail Version)

Overview

Installation under the standard retail version of Windows 95 should be a

“plug and play” operation: Windows 95 should recognize the Intel card

when it is inserted and prompt for the Intel software disk. The Intel files

will be copied to the hard drive and the computer will restart. The country

identifier utility will launch automatically.

Important Notes

Please note the following important information before starting the install

process.

• The usual path for Windows 95 files installed on your hard drive is

C:\WINDOWS\OPTIONS\CABS. The “CAB” files are com-

pressed versions of the Windows 95 distribution files. Organization

of the CD-ROM version of these files mirrors the diskette version:

If prompted to insert the disk labeled "Windows 95 Disk 1" the

corresponding CD-ROM file and path would be

"c:\windows\options\cabs\disk1.cab".

• All the Intel files required for Windows 95 installation can be found

on Intel Disk 1.

Windows 95 Installation 2-3

• Windows 95 troubleshooting information is provided in this chapter

following the installation sections.

Recommended Installation Steps

Insertion, Detection, and Prompt for Disk

1 With the computer powered-up and Windows 95 running, insert the

PRO/100 PC Card into the PC Card slot in the computer. Windows

95 will detect the insertion of the adapter. (If it does not, see item 3

of the Troubleshooting Checklist: Be sure that PCMCIA support is

enabled ... later in this chapter.)

2 At the New Hardware Found screen specifying Intel EtherExpress

PRO/100 LAN+Modem PC Card, select Driver from disk provided

by hardware manufacturer and click OK.

3 At the Install From Disk screen, insert Intel Disk 1, Installation

Disk and verify the specified path (for example: A:\). Click OK.

4 Intel files will be copied from the Intel disk and Windows 95 will

recognize the modem and network functionality of the Intel adapter.

Windows 95 Network Installation

In most cases Windows 95 network files will need to be installed, using

CAB files from diskette or CD-ROM. If another PC Card modem or

network adapter was installed previously on your system, some of these

files may already be present.

5 If prompted for Windows 95 networking files, click OK at the

Insert Disk screen.

6 At the Copying Files screen, specify the path to Windows 95

installation files (usually c:\windows\options\cabs) and click OK.

7 At the System Settings Change screen, remove the Intel disk from

the disk drive and click Yes. If Windows 95 networking was

installed, the computer will restart.

Country Identifier Utility

8 After the computer restarts and Windows 95 reloads, the country

identifier utility will be launched automatically. At the country

_Di_od_we_nn_lt_oi_afi_der_frou_mtil_Wity_wwsc_.Sre_oe_mn_a,_nm_uaa_lk_s.e_cot_mhe_{. A}a_lp_{l M}pr_ao_np_ur_ai_la_st_Se_es_ae_rl_ce_hct_Aio_ndn_Da_on_wd_nc_loo_am_d.plete

2-4 PRO/100 LAN+Modem PC Card User’s Guide

the program. (For details on this utility, see Chapter 5. Utilities and

Applications.)

Windows 95 OSR2 Installation

(OEM Version)

Overview

Installation under the OSR2 version of Windows 95 should be performed

using the Update Device Driver Wizard, as described below. Windows 95

will recognize the Intel card when it is inserted and display the Update

Device Driver Wizard window. Intel and Windows files will be located or

copied as required and the computer will restart. The Intel country

identifier utility will launch automatically.

Important Notes

Please note the following important information before starting the install

process.

• You may be prompted more than once for Intel or Windows 95

files, due to limitations in OSR2.

• The usual path for Windows 95 files installed on your hard drive is

C:\WINDOWS\OPTIONS\CABS. The "CAB" files are com-

pressed versions of the Windows 95 distribution files. Organization

of the CD-ROM version of these files mirrors the diskette version:

If prompted to insert the disk labeled "Windows 95 Disk 1" the

corresponding CD-ROM would typically be

c:\windows\options\cabs\disk1.cab.

• All the Intel files required for Windows 95 OSR2 installation can be

found on Intel Disk 1.

• Windows 95 troubleshooting information is provided in this chapter

following the installation sections.

Windows 95 Installation 2-5

Recommended Installation Steps

Insertion, Detection, and Prompt for Disk

1 With the computer powered-up and Windows 95 running, insert the

PRO/100 PC Card into the PC card slot in the computer.

2 Windows 95 will detect the Intel adapter and then display the

following Update Device Driver Wizard screen (if the adapter is not

detected, see Troubleshooting Item 3: “Be sure that PCMCIA

support is enabled ...” under Windows 95 Troubleshooting later in

this chapter).

3 Insert Intel Disk 1. Click Next>.

4 On the Update Device Driver Wizard screen click Finish.

2-6 PRO/100 LAN+Modem PC Card User’s Guide

Copying Intel Files

5 At the Insert Disk screen, click

. KO

6 At the Copying Files... screen, specify A:\ in the Copy files from:

box and click

. KO

Copying Windows 95 Network Files

In most cases Windows 95 network files will need to be installed, using

CAB files from diskette or CD-ROM. If another PC Card modem or

network adapter was installed previously on your system, some of these

files may already be present.

Windows 95 Installation 2-7

7 Windows 95 will detect new hardware and copy files. At the Insert

Disk screen, click OK.

8 At the Copying Files... screen, specify the path to the Windows 95

files (usually c:\windows\options\cabs) in the Copy files from: box

and click OK.

9 At the System Settings Change screen, remove the Intel disk from

the disk drive and click Yes. The computer will restart.

Country Identifier Utility

10 After the computer restarts and Windows 95 reloads, the country

identifier utility will launch automatically. At the country identifier

utility screen make the appropriate selection and complete the

program. (For details on this utility, see Chapter 5. Utilities and

Applications.)

2-8 PRO/100 LAN+Modem PC Card User’s Guide

How to Install for Windows 95 and NetWare

1 Install the PRO/100 PC Card driver and verify the installation as

described above in the installation procedures.

2 In the Control Panel, double-click the Network icon.

3 From the Configuration tab in the Network window, click Add.

4 From the Select Network Component Type window, select Client

and click Add.

5 Under Manufacturers in the Select Network Client window, select

Microsoft.

6 In the Network Clients window, select Client for NetWare Net-

works.

7 Click OK (you will be returned to the Network window).

8 From the Configuration tab in the Network window, click Add.

9 From the Select Network Component Type window, select Protocol

and click Add.

10 Select Microsoft as the manufacturer and IPX/SPX-compatible

Protocol under Network Protocols, then click OK to return to the

Network window.

11 Click OK to close the Network window, then restart the computer

when prompted.

Utilities

Several utilities are provided with the PRO/100 PC Card that run under

Microsoft Windows or MS-DOS. The utilities are:

• Country Identifier Utility (Windows 95, NT, 3.x)

• Modem Test (Windows 95, NT, 3.x)

• Diagnostic Test (MS-DOS prompt required)

Windows 95 Installation 2-9

These utilities are automatically copied to your hard drive during installa-

tion under Windows 95, and icons for the utilities are installed in a

Windows program group at the time of installation. See Chapter 5.

Utilities and Applications for additional information.

Power-Saving Modes

The PRO/100 PC Card has two power-saving modes to reduce adapter

power consumption under certain conditions: Network-only mode and

Modem-only mode (Network & Modem is the default).

Network-only mode disables the modem function on the adapter. This

mode should only be used when the modem will not be needed. Modem-

only mode disables the network function on the adapter. It should only be

used when the network will not be needed. When the Intel adapter is set

to either Network-only or Modem-only mode, it remains in that mode

until re-configured to a different mode.

To specify a power-saving mode under Windows 95, select Network from

Control Panel, select the Configuration tab, select Intel EtherExpress

PRO/100 LAN+Modem PC Card and click Properties, select the

Advanced tab, and select a mode in the Function(s) property (Network &

Modem is the default).

Windows 95 Troubleshooting

Quick Troubleshooting (Device Conflicts)

1 To review the adapter configuration, right-click the My Computer

icon and select Properties.

2 Select the Device Manager tab.

3 Proceed according to your version of Windows 95 (see the begin-

ning of this chapter for information):

• For Windows 95 (Retail Version), expand the item Multifunction

Adapters.

2-10 PRO/100 LAN+Modem PC Card User’s Guide

• For Windows 95 OSR2 (OEM Version), expand the item

Modem.

4 For either version, select Intel EtherExpress PRO/100

LAN+Modem PC Card (Multi-function Parent Device) and click

Properties.

5 From the Properties window, select the Resources tab.

6 Confirm that there are no conflicts with other installed devices.

Troubleshooting Checklist

The following section suggests troubleshooting steps to follow when the

Intel PC Card adapter is not automatically detected or not correctly

identified. These conditions are generally resolved by one or more of the

measures below. Detailed instructions for each measure follow.

1 Be sure you have the latest firmware and driver.

2 Run the Intel diagnostic utility M16BTEST.

3 Be sure PCMCIA support is enabled in Windows 95.

4 Create C:\WINDOWS\MODEMLOG.TXT to help resolve issues

with the modem.

5 Check other sources for updated troubleshooting information.

Note

When these directions or Windows 95 prompts you to shut down

or restart the computer, select Start, Shut Down, Shut down the

computer? Leave the computer turned off for a few seconds, and

then turn it back on. Do not press CTRL+ALT+DEL or use

your computer’s reset button to restart your computer--this can

lead to device malfunctions. On some machines, all hardware is

not reset unless power is cycled.

Windows 95 Installation 2-11

1 Be sure you have the latest firmware and

driver.

To determine what firmware and driver version you have, click My

Computer, Control Panel, Modems, highlight the Intel EtherExpress™

PRO 100 LAN+Modem PC Card (Modem), click Diagnostics, click the

Port the Intel modem is using, click More Info. The firmware information

for the adapter should display.

To find out what the latest versions are, and to download updated

versions if necessary, access the Intel BBS or web site (see the Intel

Automated Customer Support information toward the end of this guide).

2 Run the Intel diagnostic utility

M16BTEST.

To verify correct operation of the PRO/100 PC Card, run the Intel

diagnostic test utility provided on Disk 2, Network Drivers Disk. Follow

the steps below.

1 Shut down Windows 95 and power the machine off.

2 Restart Windows 95. Press the F8 key when the message Starting

Windows 95 appears on the screen. Choose Safe Mode Command

Prompt Only from the Startup menu (or press Shift+F5 to go

directly to the command prompt).

3 Run M16BTEST.EXE at the MS-DOS prompt. (See Chapter 5.

Utilities and Applications for more detailed instructions.)

4 If your Intel PC Card does not test properly, try the same procedure

on another computer. If the card still does not work, contact Intel

Customer Support.

3 Be sure that PCMCIA support is enabled

in Windows 95.

In some cases, Windows 95 PCMCIA support may not have been installed

or enabled during an upgrade or installation, due to previous machine

configurations or options selected during installation. If this Windows 95

support is not enabled, run the PCMCIA Wizard by double-clicking on

2-12 PRO/100 LAN+Modem PC Card User’s Guide

the PCMCIA icon in the Control Panel, so that Windows 95 will automati-

cally detect the type of PCMCIA controller in the machine.

4 Create C:\WINDOWS\MODEMLOG.TXT

to record the status of the modem.

Double-click My Computer, Control Panel, Modems, highlight the Intel

EtherExpress PRO 100 LAN+Modem PC Card (Modem), click Proper-

ties, Connection, Advanced, check the box Record a log file, remove any

modem strings in the box Extra settings, then click OK. If you try to dial

again and get disconnected, the file C:\WINDOWS\MODEMLOG.TXT

will be created. Review the information in that file with Intel Customer

Support.

5 Check other sources for updated

troubleshooting information.

The following information may also be helpful:

1 Review the HARDWARE.TXT file in the Windows 95 directory.

This file is written by Microsoft and describes machine specific

problems when the software was released.

2 Review the README.TXT file by clicking on the README icon

in the Program Group (or read from Intel Disk 1, Installation Disk).

This file will contain information about the driver that may not have

been available when this user manual was published.

3 Use the Intel BBS or website for updated troubleshooting informa-

tion for Windows 95. See Appendix A. Intel Automated Customer

Support, for access information.

4 Contact your computer vendor for updated information.

Windows 95 Installation 2-13

Windows 95 Driver Parameters Reference

Caution

Under most circumstances it will not be necessary to make

modifications directly to the registry. Incorrect settings can

result in undesirable changes to the configuration of Windows

95. Consult Intel Customer Support for assistance if you find it

necessary to modify the registry.

M16B.SYS (NDIS 3) Settings for Microsoft Windows 95

M16B.SYS is an NDIS 3 LAN adapter. It conforms to the Microsoft

Network Driver Interface Specification (NDIS). It supports both Win-

dows NT and Windows 95.

Windows 95 Support

The M16B.SYS driver also supports the networking environment in

Microsoft Windows 95.

The files necessary for using M16B.SYS with Windows 95 include:

NETM16B.INF

Intel network installation file for Win-

dows 95

M16B.SYS

Intel NDIS 3 driver for Windows 95

Intel modem installation file

MDMM16B.INF

MFM16B.INF

Intel multifunction installation file

2-14 PRO/100 LAN+Modem PC Card User’s Guide

There are user-configurable parameters for the M16B.SYS driver that can

be modified using the Network Control Panel applet built into Windows

95. This applet queries the user for parameter selections and then sets the

corresponding parameters in the registry. The user-configurable param-

eters are as follows:

Parameter

Default Valid Values

Registry Value

DIRECT ENABLE

EARLY TRANSMIT

OFF

OFF, ON

OFF

FULL DUPLEX

FUNCTION(S)

OFF

NETWORK&MODEM

NETWORK ONLY

MODEM ONLY

LINE SPEED

AUTO AUTO DETECT

10MBPS

100MBPS

LINK INTEGRITY

MODE

I/O

OFF

I/O

MEMORY MAPPED

NETWORKADDRESS

TRANSMITBUFFERSIZE

7168

1024-29696

The network node address can be modified by specifying a value for

‘NetworkAddress’ such as ‘00A0C9112233’. If the user does NOT specify

a ‘NetworkAddress’ then the M16B.SYS driver uses the network node

address contained in the PRO/100 Card information structure.

There are parameters in the Windows 95 registry which specify the

configuration of the EtherExpress™ PRO/100 LAN+Modem PC Card

hardware to the M16B.SYS driver. Many of these parameters correspond

directly to the user-configurable parameters. These parameters are found

in the registry at the following location:

HKEY_LOCAL_MACHINE\SYSTEM\CURRENTCONTROLSET\SERVICES\CLASS\NET\000X

Windows 95 Installation 2-15

Caution

Under most circumstances it will not be necessary to make

modifications directly to the registry. Incorrect settings can

result in undesirable changes to the configuration of Windows

95 or NT.

The registry parameters are as follows:

Keyword

Default

Valid Values

DEVICEVXDS

DEVLOADER

DIRECTENABLE

DRIVERDESC

M16B.SYS

NDIS

0-1

INTEL ETHEREXPRESS PRO/100

LAN+MODEM PC CARD (NETWORK)

EARLYTRANSMIT

ENUMPROPPAGES

FULLDUPLEX

0-1

NETDI.DLL,ENUMPROPPAGES

0-1

0-2

FUNCTIONENABLE

INFPATH

NETM16B.INF

INTERRUPTNUMBER

IOBASEADDRESS

LINESPEED

04 00 00 00

02 00 00 00

0-2

0-1

LINKINTEGRITY

MEMORYBASEADDRESS 01 00 00 00

MODE

0-1

NETWORKADDRESS

PLATFORMTYPE

TRANSMITBUFFERSIZE

11264

1024-29696

‘InterruptNumber’, ‘IoBaseAddress’, and ‘MemoryBaseAddress’ are NOT

user-configurable and their values are assigned by the Windows 95

Configuration Manager.

2-16 PRO/100 LAN+Modem PC Card User’s Guide

CHAPTER 3

Windows NT Installation

Which Version of Windows NT?

Two Versions and Two Installation Paths

Installation of the PRO/100 PC Card is different for versions 4.0 and 3.51

of Windows NT. Before starting the installation you must know what

version of Windows NT you have. If you’re using version 3.51, you must

also know the version of any software Service Pack installed.

Currently two versions of Windows NT are supported:

• Windows NT Version 4.0

• Windows NT Version 3.51 (including Service Packs)

Installation procedures are presented in two separate sections:

• Windows NT 4.0 Installation

• Windows NT 3.51 Installation

3-2 PRO/100 LAN+Modem PC Card User’s Guide

How Can I Tell Which Version and Service

Pack I Have?

• If you don't know what version you have, follow the steps below.

• If you know you have Version 4.0, skip to the Windows NT 4.0

Installation section. No additional version information is required.

• If you know you have Version 3.51, follow the steps below to

determine what Service Pack version is installed. This information is

required in step 9 of the Windows NT 3.51 Installation section.

To obtain version and Service Pack information, proceed as follows:

1 Open the Windows NT Diagnostics application in the Administra-

tive Tools folder. The Administrative Tools folder can be found in

the Program Manager window (Windows NT 3.51 interface) or by

selecting Start and Programs (Windows NT 4.0 interface).

2 In the Diagnostics application, version information can be found

either by selecting the Version tab or by clicking the OS Version ...

button.

3 If the version is 3.51, be sure to note the value of the Service Pack

field:

• For Windows NT Version 3.51 with Service Pack 5 or greater,

follow step 9a in the installation instructions for Windows NT

3.51.

• For all other versions of Windows NT 3.51, follow step 9b in the

installation instructions for Windows NT 3.51.

Additional Information in this Chapter

This chapter also contains the following information:

• Power Saving Modes

• Utilities

• Driver Parameters Reference

Windows NT Installation 3-3

Windows NT 4.0 Installation

Installing the PRO/100 PC Card under Windows NT 4.0 requires

installing the network driver and the modem separately. The network

driver must be installed first.

PCMCIA Services Verification

Before installing the Intel adapter, make sure that PCMCIA services are

enabled on your computer.

1 Select Devices from the Control Panel.

2 Scroll down the Device list to the PCMCIA device. The Status

should be Started and the Startup should be Boot. If this is not how

PCMCIA is configured, then click Startup and set the Startup Type

to Boot and click OK.

Network Driver Installation

Use the following procedure to install the network driver:

3 Shutdown the computer and turn off the power.

4 Insert the PRO/100 PC Card into the PC Card slot in the com-

puter.

5 Power-up the computer.

6 Select Network from the Control Panel.

3-4 PRO/100 LAN+Modem PC Card User’s Guide

7 Select the Adapters tab and click Add.

8 On the Select Network Adapters screen, click Have Disk. Insert

Intel Disk 1, Installation Disk and make sure the specified path is

correct, for example: A:\. Click OK.

9 Select Intel EtherExpress PRO/100 LAN+Modem PC Card and

click OK.

10 At the PRO/100 PC Card Setup screen, choose appropriate

settings. Click OK.

11 At the Network screen click Close.

12 At the Network Settings Change screen, remove the Intel disk from

the disk drive and click Yes. The computer will shut down and

restart.

Modem Setup

After the computer has been restarted, use the following procedure to

install the modem:

13 Select Modems from the Control Panel.

14 At the Install New Modem screen make sure that the "Don’t detect

my modem; I will select it from a list" checkbox is NOT checked.

Click Next. NT will query the COM ports looking for the Intel

modem. It should find the Intel modem as shown below. Click

Next>.

Windows NT Installation 3-5

15 The country identifier utility will be autmatically launched. At the

country identifier utility screen, make the appropriate country

selection.

16 At the Install New Modem screen click Finish.

17 At the Modems Properties screen click Dialing Properties... to set

up dialing properties (not necessary if a modem had been previously

installed). Click Close.

Windows NT 3.51 Installation

PCMCIA Services Verification

Before installing the Intel adapter, make sure that PCMCIA services are

enabled on your computer.

1 Select Devices from the Control Panel.

2 Scroll down the Device list to the PCMCIA device. The Status

should be Started and the Startup should be Boot. If this is not how

PCMCIA is configured, then click Startup and set the Startup Type

to Boot and click OK.

Network Driver Installation and Modem Setup

3 Shutdown the computer turn off the power.

4 Insert the PRO/100 PC Card into the PC Card slot in the com-

puter.

5 Power-up the computer.

6 Select Network from the Control Panel.

7 At the Network Settings screen click Add Adapter....

8 In the Network Adapter Card: pull-down box select <Other>

Requires disk from manufacturer and click Continue.

9 Insert Intel Disk 1, Installation Disk and make sure the specified

path is correct (see below), according to the Service Pack version

installed (see the version detection section earlier in the chapter if

you don't know what Service Pack version you have).

3-6 PRO/100 LAN+Modem PC Card User’s Guide

9a For Windows NT 3.51 with Service Pack 5 or greater, specify:

\A:

9b For all other versions of Windows NT 3.51 specify:

A:\NT351.

Click OK.

10 Select Intel EtherExpress PRO/100 LAN+Modem PC Card and

click OK.

11 At the PRO/100 PC Card Setup screen, choose appropriate

settings. Click OK.

12 The Network Settings screen should show Intel EtherExpress

PRO/100 LAN+Modem PC Card under Installed Adapter Cards.

Click OK.

13 At the Network Settings Change screen, remove the Intel disk from

the disk drive and click Yes. The computer will be shutdown and

restarted.

14 To install the country identifier utility under any version of Win-

dows NT 3.51, run the Intel Installation Program from Intel Disk 1,

Installation Disk. Use the Program Manager File/Run sequence.

Type A:\SETUP in the Command Line box, and click OK. The

country identifier utility will be copied to your hard drive and an

icon installed in the Startup Group and Intel Mobile Program

Group. The program can be run by clicking on the appropriate icon,

or it will load automatically the next time the computer is restarted.

Windows NT Installation 3-7

Power-Saving Modes

The PRO/100 PC Card has two power-saving modes to reduce adapter

power consumption under certain conditions: Network-only mode and

Modem-only mode.

Network-only mode disables the modem function on the PRO/100. This

mode should only be used when the modem will not be needed. Modem-

only mode disables the network function on the PRO/100. It should only

be used when the network will not be needed. When the adapter is set for

either mode, it remains in that mode until re-configured to a different

mode.

To specify a power-saving mode under Windows NT 4.0, select Network

from Control Panel, select the Adapters tab, select the Intel EtherExpress

PRO/100 LAN+Modem PC Card, click Properties, and select a mode in

Power-Saving Options/Function(s) (Network & Modem is the default).

Under Windows NT 3.51, select Network from Control Panel, select the

Intel EtherExpress PRO/100 LAN+Modem PC Card, click Configure,

and select a mode in Power-Saving Options/Functons(s).

Utilities

Several utilities are provided with the PRO/100 PC Card that run under

Microsoft Windows or MS-DOS:

• Country Identifier utility (Windows 95, NT, 3.x)

• Modem test (Windows 95, NT, 3.x)

• Diagnostic test (MS-DOS)

These utilities are automatically copied to your hard drive and launched

during installation under Windows NT version 4.0 or version 3.51 with

Service Pack 5 or greater. For pre-Service Pack 5 versions of NT 3.51, run

the Intel Installation Program from Intel Disk 1, Installation Disk, after

installing Windows NT version 3.51. Icons for these utilities are also

installed in the Windows program group at the time of installation. See

Chapter 5. Utilities and Applications for additional information.

3-8 PRO/100 LAN+Modem PC Card User’s Guide

Windows NT Driver Parameters Reference

M16B.SYS (NDIS 3) Settings for Microsoft Windows NT

M16B.SYS is an NDIS 3 network interface card (NIC) driver. It conforms

to the Microsoft Network Driver Interface Specification (NDIS). It

supports both Windows NT and Windows 95.

Caution

Under most circumstances it will not be necessary to make

modifications directly to the registry. Incorrect settings can

result in undesirable changes to the configuration of Windows

95 or NT. The M16B.SYS driver supports the networking

environment in Microsoft Windows NT versions 3.51 and

greater.

The files necessary for using M16B.SYS include:

For Windows NT 4.0

M16B.DLL

Intel PRO/100 installation DLL

OEMSETNT.INF Intel installation file for Windows NT

MDMM16B.INF Modem support file for Windows NT 4.0

M16B.SYS

Intel NDIS 3 driver for Windows NT

For Windows NT 3.51

M16B.DLL

Intel PRO/100 installation DLL

OEMSETNT.INF Intel installation file for Windows NT

MODEM.IN_

M16B.SYS

Compressed modem support file for

Windows NT 3.51

Intel NDIS 3 driver for Windows NT

There are user-configurable parameters to the M16B.SYS driver which can

be modified using the Network Control Panel built into Windows NT.

This applet uses the OEMSETNT.INF file to set the corresponding

parameters in the registry. The user-configurable parameters are as

follows:

Windows NT Installation 3-9

Parameter

Default

Valid Values Registry Value

DIRECT ENABLE

DISABLED

ENABLED

EARLY TRANSMIT

FULL DUPLEX

FUNCTION(S)

ENABLED

DISABLED

NETWORK

DISABLED

ENABLED

DISABLED

ENABLED

NETWORK & MODEM

NETWORK ONLY

MODEM ONLY

INTERRUPT

3, 4, 5, 7,

10, 11, 15

SAME

I/O PORT

0X320

0X2E8

0X200-0X3D0

SAME

I/O PORT

3F8,2F8,3E8,2E8

SAME

LINE SPEED

AUTO DETECT AUTO DETECT

10MBPS

100MBPS

LINK INTEGRITY

ENABLED

DISABLED

ENABLED

MEMORY ADDRESS 0XD4000

MODE I/O

0XA0000 - 0XFE000

I/O

SAME

MEMORY MAPPED

The network node address can be modified by manually editing the

registry and adding the parameter ‘NetworkAddress’ with a hexadecimal

string value, such as ‘00A0C7112233’. If the user does NOT specify a

‘NetworkAddress’ then the M16B.SYS driver uses the network node

address contained in the PRO/100 PC Card information structure.

There are parameters in the Windows NT registry which specify the

configuration of the PRO/100 PC Card hardware to the M16B.SYS

driver. Many of these parameters correspond directly to the user-

configurable parameters. These parameters are found in the registry at the

following location:

HKEY_LOCAL_MACHINE\SYSTEM\CURRENTCONTROLSET\SERVICES\M16B1\PARAMETERS\

3-10 PRO/100 LAN+Modem PC Card User’s Guide

The registry parameters are as follows:

Keyword

Default

Valid Values

BUSNUMBER

BUSTYPE

0X1

DIRECTENABLE

EARLYTRANSMIT

FULLDUPLEX

0-1

0X1

0-1

FUNCTIONENABLE

INTERRUPTNUMBER

IOBASEADDRESS

IOBASEADDRESS_1

IOLENGTH

0-2

0X5

0X2E8

0X320

0X07

0XF

3,4,5,7,8,9,A,B,F

3F8,2F8,3E8,2E8

0X200 - 0X3D0

IOLENGTH_1

LINESPEED

0-2

0-1

LINKINTEGRITY

MEMORYMAPPEDBASEADDRESS

MEMORYMAPPEDSIZE

MODE

0X1

0XD6000 A2000-FF000

0X1000

0-1

MODEMFUNCTION

NETWORKADDRESS

0X01

PCCARDATTRIBUTEMEMORYADDRESS 0XD4000 A0000 - FE000

PCCARDATTRIBUTEMEMORYOFFSET 0XF000

PCCARDATTRIBUTEMEMORYSIZE

PCCARDMEMORYWINDOWOFFSET

PCMCIA

0X2000

0-1

PLATFORMTYPE

TRANSMITBUFFERSIZE

0X1C00 0X0400-0X1E800

CHAPTER 4

Windows 3.x/DOS Installation

This chapter contains comprehensive information on how to install and

configure the PRO/100 PC Card for systems running Microsoft Windows

3.x and MS-DOS. The topics covered are:

• Installation under MS-DOS

• Installation under Windows 3.x

• Windows 3.x Network Operating System Alphabetical Reference

• Windows 3.x Modem Configuration Notes

• Windows 3.x Network Driver Parameters

• Error Messages for Windows and Windows 3.x/DOS Drivers

• Windows 3.x Troubleshooting

• Computer-Specific Application Notes (Windows 3.x)

4-2 PRO/100 LAN+Modem PC Card User’s Guide

Installation under MS-DOS

For systems running MS-DOS without Windows, see “Manual Installa-

tion” in the “Alphabetical Reference” section later in this chapter.

Installation under Windows 3.x (including

Windows for Workgroups)

Run the Intel Installation Program if you are using Windows 3.1 or

Windows for Workgroups 3.11. Proceed as follows:

1 With Windows running, insert Disk 1, Installation Disk, into your

disk drive.

2 From the Program Manager, choose File, then Run. In the Com-

mand Line box, type the following:

A:SETUP

3 Press Enter or click OK.

4 Select your network operating system from the list displayed and

click OK.

5 Follow the on-screen instructions. Note the following variations for

NetWare and other network operating systems:

Novell NetWare Installation

With Novell NetWare highlighted, click the OK button. Intel

provides all software necessary to configure your NetWare client

workstation. Upon completion, the Installation Program will reboot

your system. When your system comes back up, log in to the

network.

Note

The NetWare VLM shell is used to connect to your NetWare

server. The Intel Installation Program will decompress and

configure the necessary files. If you do not plan to use the

Installation Program, see “Manual Installation” in the

“Alphabetical Reference” later in this chapter for instructions on

how to decompress and load the NetWare VLM files.

If you need NETX shell support, contact your System Adminis-

trator.

Windows 3.x/MS-DOS Installation 4-3

Installation of Other Network Operating Systems

For listed network operating systems other than Novell NetWare,

highlight your network operating system and click the OK button.

6 Once you have completed the steps prompted by the Intel Installa-

tion Program, exit the program and find your network operating

system in this chapter of the User’s Guide, using the “Alphabetical

Reference.” Follow the procedures indicated there to complete the

installation.

The Installation Program will modify your AUTOEXEC.BAT,

CONFIG.SYS, and network configuration files to match the

optimum configuration for your system.

Completing the Installation

Use the instructions in the next section “Windows 3.x Network Operating

System Alphabetical Reference” under the following circumstances:

• To complete the installation of network drivers under Windows 3.x

after you have run the Intel Installation Program. Find your network

operating system in the alphabetical listing and follow the steps

there.

• To install network drivers manually under a network operating

system not supported by the Intel Installation Program. See the

instructions under “Generic Installation” or “Manual Installation” in

the “Windows 3.x Network Operating System Alphabetical Refer-

ence.”

Windows 3.x Network Operating System

Alphabetical Reference

This section is organized in alphabetical order by network operating

system vendor or topic. Unless otherwise indicated, these instructions are

designed to be used with the Intel Installation Program. They assume a

first-time installation of client software on a workstation, using the

configuration values set by the Intel Installation Program or, when the

Installation Program is not used, using the default values listed in “Win-

dows 3.x Network Driver Parameters Reference” later in this chapter.

4-4 PRO/100 LAN+Modem PC Card User’s Guide

The PRO/100 PC Card supports ODI, NDIS (version 2.01) and packet

drivers under Windows 3.x. To determine which of these drivers you need

for your networking environment, consult your network administrator or

network documentation.

Artisoft LANtastic version 6.0

NDIS 2.0 Driver

1 Run the Intel Installation Program from the Installation Disk.

2 Choose Artisoft LANtastic from the Select Network Operating

System screen.

3 Follow the prompts to complete the Intel segment of the installa-

tion.

4 Run the Artisoft LANtastic 6.0 “install” program. Specify

C:\LANTASTI as the destination directory (or the drivers directory

as specified in the Intel Installation Program).

5 At the “Select network adapter” screen, choose “NDIS Support for

Network Adapters.”

6 When prompted for the “manufacturer’s driver disk” on the “Enter

NDIS driver directory” screen, insert the Intel Network Drivers

Disk.

7 Complete the Artisoft installation.

8 Reboot the computer and start LANtastic.

AT&T StarGROUP LAN Manager version

2.1a

NDIS 2.0 Driver

See Microsoft LAN Manager.

Windows 3.x/MS-DOS Installation 4-5

Banyan VINES version 5.5

NDIS 2.0 Driver

Prior to installing the Banyan Vines client software, it is necessary to

determine the Interrupt Number for the PRO/100 PC Card. After you

have installed the Adapter, follow these steps to determine the Interrupt

Number:

1 Insert Intel Disk 2, Network Drivers Disk in the floppy drive.

2 At the DOS prompt, enter

M16BTEST.EXE

3 Press Enter.

4 When the Main Menu opens, run Test.

The IRQ number will be displayed when the Test is complete.

5 Write down the IRQ number to use when you proceed with the

installation.

For example, if the IRQ=6, write down the number 6.

Now continue with the Banyan Vines installation as follows:

1 In Windows 3.x run the Intel Installation Program from Intel Disk

1. Installation Disk, as described at the beginning of this chapter.

2 Choose Banyan VINES from the Select Network Operating System

screen.

3 Follow the prompts to complete the Intel segment of the installa-

tion. The Installation Program also creates a \VINES directory on

your hard disk.

4 Copy the files from the VINES Master disk into the VINES

directory.

5 Copy the PROTOCOL.INI file from the \NDIS directory on Intel

Disk 2. Network Drivers Disk into the VINES directory.

6 Change to the VINES directory.

7 Type PCCONFIG and select Network Card Settings, followed by

NDIS Ethernet.

8 Enter the IRQ value you wrote down in step 5 of the M16BTEST

procedure described above.

4-6 PRO/100 LAN+Modem PC Card User’s Guide

9 At the PROTOCOL.INI bindings prompt, type INTELNET.

10 Press F10 to save and Esc to return to the main menu.

11 Select Login Environment Settings, followed by Default Communi-

cations Driver, followed by NDIS Ethernet.

12 Press Esc to return to the Main Menu and press F10 to save.

13 Manually add these lines to your AUTOEXEC.BAT file:

CD\VINES

BAN

DEC PATHWORKS versions 5.x or 6.x

NDIS 2.0 Driver

These instructions are based on PATHWORKS documentation for

configuration of a PC as a client workstation, using a system service

already installed on a LAN Manager server and the LAN Manager SETUP

diskette.

Prior to installing the DEC PATHWORKS client software, it is necessary

to determine the Interrupt Number for the PRO/100 PC Card. After you

have installed the PRO/100 PC Card, follow these steps to determine the

Interrupt Number:

1 Insert the Intel Network Drivers Disk in the floppy drive.

2 At the DOS prompt, enter

M16BTEST.EXE

3 Press Enter.

4 When the Main Menu opens, run Test.

The IRQ number will be displayed when the Test is complete.

5 Write down the IRQ number to use when you proceed with the

installation.

For example, if the IRQ=6, write down the number 6.

Windows 3.x/MS-DOS Installation 4-7

Now continue with the DEC PATHWORKS installation as follows:

1 In Windows 3.x run the Intel Installation Program from Intel Disk

1. Installation Disk, as described at the beginning of this chapter.

2 Choose DEC PATHWORKS from the Select Network Operating

System screen.

3 Follow the prompts to complete the Intel segment of the installa-

tion.

4 Check the README file on your PATHWORKS SETUP disk for

requirements such as lastdrive, setver, etc. You will need 500 K of

free conventional memory and about 1 MB of extended memory to

run PATHWORKS SETUP. Be sure you have a lastdrive statement

in your CONFIG.SYS file (lastdrive=g will work in most cases).

5 Use a text editor to modify the file A:\NDIS\PI.TPL on the

PATHWORKS SETUP disk, as follows (A:\NDIS is a hidden

directory. You can access it by typing CD A:\NDIS):

Change the line

;NI_IRQ = [IRQ VALUE FROM STEP 5 OF THE FIRST PROCEDURE ABOVE]

to read

NI_IRQ = [IRQ VALUE FROM STEP 5 OF THE FIRST PROCEDURE ABOVE]

The NI_IRQ value must be the same as the interrupt value you will

use for the Intel adapter.

6 Run the SETUP program from the PATHWORKS SETUP disk for

LAN Manager.

7a For Pathworks 5.0, choose Configure PC.

7b For Pathworks 6.0, select Yes for the “Has the Pathworks software

been installed to a LAN Manager file Service.”

8 In the Select Drive Window, choose “Network.”

9 Select DECnet as transport.

10 When prompted to choose a network adapter, choose “Other.”

11 When prompted for driver information, in the “Other Adapter”

window use the following:

a. for PATHWORKS 5.0:

NDIS DRIVER PATH: A:\

4-8 PRO/100 LAN+Modem PC Card User’s Guide

NDIS DRIVER FILE: M16BNDIS.EXE

NDIS DRIVER NAME: INTEL$

b. for PATHWORKS 5.1:

DRIVER FILE: A:\M16BNDIS.EXE

PROTOCOL.INI STUB: A:\DEC\PROTOCOL.INI

c. for PATHWORKS 6.0:

DRIVER FILE: A:\M16BNDIS.EXE

PROTOCOL.INI STUB: A:\DEC\PROTOCOL.INI

Skip the Additional Files section.

12 Insert Intel Disk 2, Network Drivers Disk when prompted.

13 Enter your node information when prompted.

14 Save the PROTOCOL.INI file with the default settings.

At this point, the SETUP program will try to connect to the

DECnet server. Once connected, the SETUP program will map a

logical drive to your system service.

15 Highlight the logical drive mapped by the SETUP program, and

press Enter to run PWSETUP.

16 Press Enter to confirm the Software Destination C:\PW.

17 Choose Express (or Custom if you have a lot of prior installation

experience).

18 Select an appropriate Workstation Template, or create one.

19 Under Network Adapter Information, choose other network

adapter, with NDIS enabled, and enter the following information:

IN THE NON-SUPPORTED NETWORK ADAPTER WINDOW

DRIVER FILE: A:\M16BNDIS.EXE

PROTOCOL.INI STUB: A:\DEC\PROTOCOL.INI

Skip the Additional Files section and ensure Ethernet box is

enabled.

20 Insert Intel Disk 2, Network Drivers Disk when prompted.

21 In the Network Adapter Information window, select M16BNDIS

Unsupported Network Adapter with NDIS Box enabled

Windows 3.x/MS-DOS Installation 4-9

22 In LAN Manager System Service Connection Information window,

enter username and press Enter.

23 Enter the Windows directory path.

24 Press Enter to add the STARTNET.BAT file to your

AUTOEXEC.BAT file.

25 A PROTOCOL.INI file created by SETUP will display in edit

mode.

Remove the semicolon at the beginning of the ni_irq line, as

follows:

Change the line

;NI_IRQ = [IRQ VALUE FROM STEP 5 OF THE FIRST PROCEDURE ABOVE]

to read

NI_IRQ = [IRQ VALUE FROM STEP 5 OF THE FIRST PROCEDURE ABOVE]

The ni_irq value must be the same as the interrupt value used for

the Intel adapter.

Verify that the [M16BNDIS]` section has the following lines and

settings:

[M16BNDIS]

DRIVERNAME=INTEL$

26 Exit SETUP and reboot to start the network. (Some machines may

require a cold boot at this point—power the computer down and

back up again.)

FTP Software LANWatch

Packet and NDIS 2.0 Drivers

FTP Software’s LANWatch network monitor software can be installed

using Intel’s packet or NDIS 2.0 drivers. For information on which driver

is appropriate for your network environment, refer to the FTP LANWatch

documentation.

FTP Software LANWatch Packet Driver Installation

1 Run the Intel Installation Program from the Installation Disk.

4-10 PRO/100 LAN+Modem PC Card User’s Guide

2 Choose FTP LANWatch from the Select Network Operating

System screen.

3 Follow the prompts to complete the Intel segment of the installa-

tion.

4 Install LANWatch according to the instructions in your FTP

LANWatch manual.

5 Copy the file M16BPD.COM from the C:\INTEL\M16B directory

to the directory where your LANWatch files are stored.

6 (This step is not required for LANWatch versions 3.0 and later.)

Using a text editor, add the following line to your CONFIG.SYS

file:

DEVICE = [PATH]IFCUST.SYS

where [path] is the drive and directory where your LANWatch files

are stored.

7 Reboot the PC.

8 Change to the directory of where your LANWatch files are stored

and run M16BPD.COM.

9 Run LW.EXE.

FTP Software LANWatch NDIS 2.0 Driver Installation

1 Run the Installation Program from Intel Disk 1, Installation Disk.

2 Choose FTP LANWatch from the Select Network Operating

System screen.

3 Follow the prompts to complete the Intel segment of the installa-

tion.

4 Install LANWatch according to the instructions in your FTP

LANWatch manual.

5 Using a text editor, add the following lines to your CONFIG.SYS

file:

DEVICE = C:\NDIS\PROTMAN.SYS /I:C:\NDIS

DEVICE = C:\NDIS\FTPSOFT.DOS

DEVICE = C:\NDIS\M16BNDIS.EXE

DEVICE = C:\NDIS\DIS_PKT.GUP

(Include the following line for LANWatch versions earlier than 3.0

only)

Windows 3.x/MS-DOS Installation 4-11

DEVICE = C:\LW\IFCUST.SYS

6 Create a directory called NDIS on your hard disk, by typing:

MD NDIS

7 At the DOS prompt, copy M16BNDIS.EXE from the

C:\INTEL\M16B directory on your hard disk and the file

PROTOCOL.FTP from the \NDIS directory on the Intel Network

Drivers Disk to the \NDIS directory you created in Step 6.

8 Use a text editor to modify the PROTOCOL.FTP file to match the

keywords and values in the sample PROTOCOL.INI file in the

\INTEL\M16B directory.

9 Copy all the files from the \NDIS directory on the FTP Unsup-

ported Software Disk A to the \NDIS directory created in Step 6.

10 Reboot the PC.

11 Change to the \NDIS directory and run NETBIND.EXE.

12 Run LW.EXE.

FTP Software PC/TCP

Packet, NDIS 2.0, and ODI Drivers

The PC/TCP Generic Ethernet Kernel ETHDRV.EXE can be installed

using Intel’s Packet, ODI, or NDIS drivers. PC/TCP can also be used

concurrently with NetWare. For information on which driver is appropri-

ate for your network environment, see the FTP PC/TCP documentation.

For environments using values other than those set by the Intel Installa-

tion Program, see the heading Windows 3.x Network Driver Parameters

later in this chapter.

FTP PC/TCP 3.X with OnNet 1.1 and Windows for

Workgroups 3.11

1 Run the Installation Program from Intel Disk 1, Installation Disk.

2 From the Select Network Operating System screen, choose Win-

dows for Workgroups then FTP PC/TCP 3.x.

3 Follow the prompts to complete the Intel segment of the installa-

tion.

4 Run the PC/TCP installation program OnNet 1.1

4-12 PRO/100 LAN+Modem PC Card User’s Guide

5 Follow the prompts to the Network Card Screen, then select “Other

NDIS Driver or Updated Packet Driver.”

6 Insert Intel Disk 2, Network Drivers Disk when prompted.

7 Choose the appropriate driver then follow prompts to complete the

installation.

8a For NDIS installation, reboot the PC.

8b For ODI installation, do not reboot. Continue with step 9.

Additional Steps for ODI Installation

If you are using an ODI driver, continue with the following steps:

9 Change to the directory into which PC/TCP was installed.

10 Use a text editor to change the file PCTCP.INI as follows:

• In the section PCTCP ifcust 0 change the line

INTERFACE-TYPE=NDIS

to read

INTERFACE-TYPE=PKTDRV

11 Save the file and exit the text editor.

12 Change to the C:\ (root) directory.

13 Use a text editor to modify the AUTOEXEC.BAT file as follows

(\PCTCP is the default installation directory):

• Move the line containing the STARTNET.BAT command or the

lines containing the network driver files to immediately above the

line

SET PCTCP=C:\PCTCP\PCTCP.INI

• Add the line

C:\PCTCP\ODIPKT

after the line

PCTCP=C:\PCTCP\PCTCP.INI

14 Save the file and exit the text editor.

15 Copy the file ODIPKT from disk 5 of the FTP PC/TCP installation

disks to the directory into which PC/TCP was installed.

16 Reboot the PC.

Windows 3.x/MS-DOS Installation 4-13

FTP PC/TCP 3.X with OnNet 1.1 with Windows 3.1

1 Run the Installation Program from Intel Disk 1, Installation Disk.

2 From the Select Network Operating System screen, choose FTP

PC/TCP.

3 Follow the prompts to complete the Intel installation.

4 Run the PC/TCP installation program OnNet 1.1.

5 When prompted, insert Intel Disk 2, Network Drivers Disk.

6 Follow prompts to complete the PC/TCP installation.

7a For an NDIS installation, reboot the PC.

7b For ODI installation, do not reboot. Continue with step 8.

Additional Steps for ODI Installation

If you are using an ODI driver, continue with the following steps:

8 Change to the directory into which PC/TCP was installed.

9 Use a text editor to change the file PCTCP.INI as follows:

• In the section PCTCP ifcust 0 change the line

INTERFACE-TYPE=NDIS

to read

INTERFACE-TYPE=PKTDRV

10 Save the file and exit the text editor.

11 Change to the C:\ (root) directory.

12 Use a text editor to modify the AUTOEXEC.BAT file as follows

(\PCTCP is the default installation directory):

• Move the line containing the STARTNET.BAT command or the

lines containing the network driver files to immediately above the

line

SET PCTCP=C:\PCTCP\PCTCP.INI

• Add the line

C:\PCTCP\ODIPKT

after the line

PCTCP=C:\PCTCP\PCTCP.INI

13 Save the file and exit the text editor.

4-14 PRO/100 LAN+Modem PC Card User’s Guide

14 Copy the file ODIPKT from disk 5 of the FTP PC/TCP installation

disks to the directory into which PC/TCP was installed.

15 Reboot the PC.

FTP Software PC/TCP Packet Driver Installation with

OnNet 1.1

1 Run the Installation Program from Intel Disk 1, Installation Disk.

2 Choose FTP PC/TCP from the Select Network Operating System

screen.

3 Follow the prompts to complete the Intel segment of the installa-

tion.

4 Exit to DOS, switch to the C:\INTEL\M16B directory and run

M16BPD.COM.

5 Install PC/TCP software according to the directions given in the

PC/TCP documentation.

6 Copy the file M16BPD.COM from the C:\INTEL\M16B directory

to the PC/TCP directory specified in the PC/TCP install procedure.

7 Edit the AUTOEXEC.BAT file and add the following lines:

C:\PCTCP\M16BPD.COM

C:\PCTCP\ETHDRV.EXE

8 (This step is not required for PC/TCP versions 2.10 and later.)

Using a text editor, add the following lines to your CONFIG.SYS

file:

DEVICE=[PATH]IPCUST.SYS

DEVICE=[PATH]IFCUST.SYS

where [path] is the drive and directory specified at the PC/TCP

installation.

9 Reboot the PC.

10 Change to the directory where your PC/TCP files are stored and

run M16BPD.COM by typing:

M16BPD

11 Run the ETHDRV.EXE kernel program supplied with PC/TCP.

This loads the PC/TCP kernel into memory. The packet driver must

always load before the kernel.

Windows 3.x/MS-DOS Installation 4-15

12 Continue your server or workstation startup as instructed in the

PC/TCP documentation.

ODI with FTP Software PC/TCP and NetWare

If you need to run Novell NetWare concurrently with FTP PC/TCP,

proceed as follows:

1 Run the Installation Program from Intel Disk 1, Installation Disk.

2 Choose FTP PC/TCP from the Select Network Operating System

screen.

3 Follow the prompts to complete the Intel segment of the installa-

tion.

4 Install PC/TCP according to the instructions in your FTP PC/TCP

manual.

5 (This step is not required for PC/TCP versions 2.10 and later.)

Using a text editor, add the following lines to your CONFIG.SYS

file:

DEVICE=[PATH]IPCUST.SYS

DEVICE=[PATH]IFCUST.SYS

where [path] is the drive and directory specified in the PC/TCP

installation.

6 Copy NET.CFG from the C:\INTEL\M16B directory and the files

LSL.COM and M16BODI.COM from the root directory of the

Intel Network Drivers Disk to the PC/TCP directory created in the

PC/TCP install procedure.

7 To start the workstation, load the software as follows:

LSL

M16BODI

IPXODI

ODIPKT (USE THE VERSION SUPPLIED WITH PC/TCP)

ETHDRV

VLM

8 Change to the network drive (usually F:\LOGIN).

9 Log in to the network.

4-16 PRO/100 LAN+Modem PC Card User’s Guide

Generic Installation

If your network operating system is not listed in the Intel Installation

Program, you can try selecting “Generic NDIS Driver” or “Generic ODI

Driver” in the Intel Installation Program and clicking the Install button. A

sample configuration file containing parameters optimized for your system

will be created in the \INTEL\M16B directory on your hard disk. For

NDIS, this will be a custom PROTOCOL.INI file. For ODI, it will be a

custom NET.CFG file. Use this sample file to assist you in configuring the

actual configuration file for your system (or use the sample file itself if

appropriate).

HP LAN Manager

NDIS 2.0 Driver

See Microsoft LAN Manager.

IBM Local Area Network Support Program

IBM Local Area Network Support Program (version

1.36)

NDIS 2.0 Driver

1 Run the Installation Program from Intel Disk 1, Installation Disk.

2 Choose IBM LAN Support Program from the Select Network

Operating System screen.

3 Follow the prompts to complete the Intel segment of the installa-

tion.

4 Install the IBM Local Area Network Support Program according to

the instructions in the IBM Local Area Network Support Program

User’s Guide.

5 Under Environment Information, respond “no” to the question

“Do you have adapter option disks?”

6 Choose any adapter from the list provided.

7 If prompted to do so, insert the Intel Disk 2, Network Drivers Disk

when prompted and type the path

A:\NDIS

Windows 3.x/MS-DOS Installation 4-17

8 Press Esc twice to bypass error messages.

9 Continue with the installation until finished.

10 Use a text editor to add the following two lines in your

CONFIG.SYS file at the location indicated by the “rem” statement

concerning insertion of the driver name:

DEVICE=\LSP\M16BNDIS.EXE

11 Copy M16BNDIS.EXE from the directory C:\INTEL\M16B to

the C:\LSP directory on your hard disk.

12 Use a text editor to edit the PROTOCOL.INI keyword settings in

the C:\LSP directory to match the keywords contained in the

sample PROTOCOL.INI file located at C:\INTEL\M16B as

required (unless you are using Intel PRO/100 default settings).

13 Save the files and reboot the PC.

IBM Local Area Network Support Program (version 1.2)

NDIS 2.0 Driver

1 Run the Installation Program from Intel Disk 1, Installation Disk.

2 Choose IBM LAN Support Program from the Select Network

Operating System screen.

3 Follow the prompts to complete the Intel segment of the installa-

tion.

4 Install the IBM Local Area Network Support Program according to

the instructions in the IBM Local Area Network Support Program

User’s Guide. The following instructions refer to the prompts and

messages displayed with the Configuration Aid automated install

software provided with the LAN Support Program.

5 If a message appears during the LAN Support Program installation

indicating there are no IBM LAN adapters installed in the worksta-

tion, bypass the message by pressing Enter.

6 Answer [N]o to program support for the PC Network Adapter.

7 Answer [Y]es to use of programs needing the NETBIOS interface.

8 When prompted, select the Etherand Network family of network

cards.

9 Continue with the installation until finished.

4-18 PRO/100 LAN+Modem PC Card User’s Guide

10 Use a text editor to replace the line in your CONFIG.SYS file that

reads:

DEVICE=\XX.DOS

with the line

DEVICE=\M16BNDIS.EXE

11 Still in the CONFIG.SYS file, add the parameter O=N (where O is

a letter, not zero) to the line

DEVICE=\DXMT0MOD.SYS

as follows

DEVICE=\DXMT0MOD.SYS O=N

12 Copy M16BNDIS.EXE from the directory C:\INTEL\M16B to

the root directory of your hard disk or boot disk.

13 Change to the LANMAN directory on your hard disk or boot disk.

14 Use a text editor to modify the PROTOCOL.INI file in the C:\LSP

directory as follows:

• Under the ETHERAND section, change the line that reads

BINDINGS = TCMAC2

to:

BINDINGS = INTELNET

• Underneath that section insert a new section that reads:

[INTELNET]

DRIVERNAME = INTEL$

15 Use a text editor to edit the keyword settings in the

PROTOCOL.INI file in the C:\LSP directory to match the

keywords contained in the sample PROTOCOL.INI file located at

C:\INTEL\M16B as required (unless you are using Intel PRO/100

default settings).

16 Save the file and reboot the PC.

IBM PC LAN and IBM DOS LAN Requester

1 Install the IBM LAN Support Program according to the instructions

under the heading “IBM Local Area Network Support Program,”

which immediately precedes this one.

Windows 3.x/MS-DOS Installation 4-19

2 Reboot the PC.

3 Install IBM PC LAN or IBM DOS LAN Requester according to the

instructions in the IBM documentation.

4 Reboot the PC.

Manual Installation

All network drivers provided on Intel Disk 2, Network Drivers Disk can

be installed manually, without the Intel Installation Program. You must

copy the correct driver files to your hard disk and make appropriate

changes to CONFIG.SYS, AUTOEXEC.BAT, and configuration files

such as NET.CFG (for ODI) or PROTOCOL.INI (for NDIS). Manual

installation should only be performed by a system administrator or

someone with equivalent knowledge of the installation process for

your network operating system.

Note

For manual installation of Novell NetWare with VLM (available

only under MS-DOS or Windows 3.x) you must first decompress

the VLM files by running the MS-DOS batch file

DCOMPVLM.BAT from the Network Drivers Disk, as follows:

DCOMPVLM [PATH]

where [path] is the directory for NetWare files (usually

C:\NWCLIENT). DCOMPVLM will decompress and copy all

required files to the designated directory.

For an overview of the installation process, see the instructions provided

for your network operating system in the alphabetical section of this

chapter. Consult the section Windows 3.x Network Driver Parameters

later in this chapter for detailed information on configuration files and

settings. For additional information, consult your network operating

system documentation.

4-20 PRO/100 LAN+Modem PC Card User’s Guide

Microsoft LAN Manager

Microsoft LAN Manager (version 2.1)

NDIS 2.0 Driver

1 Run the Installation Program from Intel Disk 1, Installation Disk.

2 Choose Microsoft LAN Manager from the Select Network Operat-

ing System screen.

3 Follow the prompts to complete the Intel segment of the installa-

tion.

4 Begin installation of LAN Manager using “setup.”

5 When prompted to select the available network adapter driver,

choose “Other Driver.”

6 When prompted, insert Intel Disk 2, Network Drivers Disk.

7 Select “Intel EtherExpress PRO/100 LAN+Modem PC Card”

from the menu.

8 Continue with the installation until it is completed.

9 If installing Microsoft LAN Manager to run under Windows

proceed to step 10. Otherwise, skip to step 15.

10 Run Windows.

11 Choose setup from “Main” group.

12 Select Startup, and under the “Options” screen select Change

System Settings.

13 Select Network then scroll to LAN Manager version 2.1.

14 Follow the prompts to complete the installation.

15 Reboot the PC.

Microsoft LAN Manager (version 2.1) with Windows for

Workgroups 3.11

1 Run the Installation Program from Intel Disk 1, Installation Disk.

2 Choose Microsoft Windows for Workgroups from the Select

Network Operating System screen.

3 Select “Yes” on the Attached to Network File Server screen.

4 Select Microsoft LAN Manager.

Windows 3.x/MS-DOS Installation 4-21

5 Follow the prompts to complete the Intel segment of the installa-

tion.

6 Start Windows and, in the Network program group, double-click on

the Network Setup icon.

7 If you have not installed network support, choose Networks in the

Network Setup dialog box, select Install Microsoft Windows

Network, and click OK. Otherwise proceed with step 8.

8 In the Network Setup dialog box, choose Drivers.

9 In the Network Drivers dialog box, choose Add Adapter.

10 In the Add Network Adapter box, choose Unlisted or Updated

Network Adapter and click OK.

11 When prompted for an “unlisted, updated, or vendor-provided

network driver disk,” insert the Intel Network Drivers Disk.

12 Select “Intel M16B NDIS 2.01 Real Mode,” and click OK.

13 Close the Network Drivers dialog box and click OK in the Network

Setup box.

14 Complete the installation process, inserting Intel Disk 2, Network

Drivers Disk if required.

15 Continue with the installation until it is completed.

16 Click on the Control Panel in the “Main” group.

17 Select Startup from the Control Panel.

18 In the Options for Enterprise Networking window click “Log on to

Windows NT or LAN Manager Domain.”

19 Save, exit, and reboot the PC.

Windows for Workgroups

NDIS 2.01 and ODI Drivers

Instructions are provided for installing Intel network drivers for the first

time on a system using Windows for Workgroups version 3.11 alone or

with NetWare. These instructions assume that Windows for Workgroups

has already been installed. Remove any earlier version of the Intel drivers

before installing the new version. No NDIS 3 driver is supplied for

Windows for Workgroups.

4-22 PRO/100 LAN+Modem PC Card User’s Guide

The following topics are covered for Windows for Workgroups:

• How to install for Windows for Workgroups version 3.11 and

NetWare using the ODI driver

• How to install for Windows for Workgroups 3.11 using the NDIS

2.0 driver

• How to Disable Windows for Workgroups Networking

For troubleshooting tips for Windows for Workgroups, see Chapter 4.

Troubleshooting.

Windows for Workgroups Version 3.11 and NetWare

(Using the ODI driver)

1 To configure Windows for Workgroups with NetWare, run the Intel

Installation Program from Disk 1 and choose Windows for Work-

groups.

2 Choose YES to “Connect to Network Server.”

3 Choose “Novell NetWare” as your network server.

4 When the installation is complete, reboot the computer.

5 At the Intel menu, choose “Load Intel EtherExpress PRO/100

LAN+Modem PC Card for Network Access.”

6 From the DOS prompt, run the NetWare Client install. Be sure to

install support for Windows.

7 When the Novell Client install program asks for an ODI driver,

insert the Intel Network Drivers Disk.

8 Complete the installation process and reboot the computer.

9 Log in to NetWare.

10 Start Windows for Workgroups and, in the Network program

group, double-click on the Network Setup icon.

Windows for Workgroups Network Setup will detect the NetWare

configuration and automatically select Novell NetWare as an

additional network. It will also prompt for Novell support files

(from Novell Client diskettes) if required during the installation. (If

necessary, use the Novell decompression utility to decompress the

required files.)

Windows 3.x/MS-DOS Installation 4-23

Windows for Workgroups Setup will also attempt to determine what

NetWare driver model you are using. If for some reason Windows

for Workgroups was unable to detect the driver model, you should

select IPXODI and LSL as the driver type.

Note that you can install NetWare as an additional network under

Windows for Workgroups, as follows:

11 In the Network Setup dialog box, choose Networks.

12 To install both Windows for Workgroups and NetWare, choose

Install Microsoft Windows Network.

13 Choose Other under Additional Network Support, then select the

NetWare configuration appropriate for your network.

14 If you want to share your files or printers with others, select

“Sharing.”

15 In the Network Setup dialog box, choose Drivers.

16 In the Network Drivers dialog box, choose Add Adapter.

17 In the Add Network Adapter box, choose Unlisted or Updated

Network Adapter and click OK.

18 When prompted for an “unlisted, updated, or vendor-provided

network driver disk,” insert the Intel Network Drivers Disk and

click OK.

19 Select “Intel M16B ODI for NetWare” and click OK.

20 Close the Network Drivers dialog box and click OK in the Network

Setup box.

21 Complete the installation process, inserting Intel Disk 2: Network

Drivers Disk if required.

22 Reboot the computer.

Note

Verify that the following lines have been added to your

AUTOEXEC.BAT and STARTNET.BAT files. If they are not

there, add them manually using a text editor.

4-24 PRO/100 LAN+Modem PC Card User’s Guide

Add the following command to the AUTOEXEC.BAT file,

where \WINDOWS is the directory into which Microsoft

Windows was installed:

C:\WINDOWS\NET START

Add the following command to the STARTNET.BAT file in

your NWCLIENT directory, where \WINDOWS is the directory

into which Microsoft Windows was installed:

C:\WINDOWS\ODIHLP.EXE

Windows for Workgroups 3.11 Using the NDIS 2.0

Driver

1 Run the Installation Program from Intel Disk 1, Installation Disk.

2 Choose Microsoft Windows for Workgroups installation from the

Select Network Operating System screen.

3 Choose “No” on the Attached to Network File Server screen.

4 Follow the prompts to complete the Intel segment of the installa-

tion.

5 Start Windows for Workgroups and double-click on the Network

Setup icon in the Network Group.

6 If you have not installed network support, choose Networks in the

Network Setup dialog box, select Install Microsoft Windows

Network, and click OK. Otherwise proceed to Step 7. Click the

Sharing button to share files and printers.

7 In the Network Setup dialog box, choose Drivers.

8 In the Network Drivers dialog box, choose Add Adapter.

9 In the Add Network Adapter box, choose Unlisted or Updated

Network Adapter and click OK.

10 When prompted for an “unlisted, updated, or vendor-provided

network driver disk,” insert the Intel Network Drivers Disk.

11 Select “Intel M16B NDIS 2.01 Real Mode” and click OK.

12 Close the Network Drivers dialog box and click OK in the Network

Setup box.

13 Complete the installation process, inserting Intel Disk 2, Network

Drivers Disk if required.

Windows 3.x/MS-DOS Installation 4-25

How to Remove an Existing Windows for Workgroups

Installation

1 Start Windows and select Network Setup in the Network program

group.

2 In the Network Setup dialog box, choose Drivers.

3 In the Network Drivers dialog box, choose Remove to discard any

existing network adapter drivers.

4 Choose Close and return to the Network Setup dialog box.

5 Exit the Network Setup program and exit Windows.

6 At the DOS prompt, change to the Windows system directory, as

follows

CD \WINDOWS\SYSTEM

7 Make a directory called OEM, as follows

MKDIR OEM

8 Type

DIR OEM?.INF

to see a list of driver configuration files.

9 Use the DOS EDIT program to view each OEM file to determine

which ones reference Intel.

10 Copy the old Intel configuration files to the OEM directory.

11 Delete the old Intel configuration files from the Windows system

directory.

12 Restart Windows.

13 Follow the instructions for installing drivers for Windows for

Workgroups alone or Windows for Workgroups and NetWare.

4-26 PRO/100 LAN+Modem PC Card User’s Guide

Novell NetWare

ODI Driver

The Intel ODI driver allows for the concurrent use of Novell NetWare

and other protocols that support Novell’s Open Data-Link Interface

(ODI) specification.

NetWare

1 Run the Intel Installation Program from the Installation Disk.

2 Choose Novell NetWare from the Select Network Operating

System screen.

3 Follow the prompts to complete the installation.

4 The Intel Installation Program will reboot the computer and verify

the NetWare connection.

5 Log in to the network.

Note

The Intel Installation Program uses the NetWare VLM shell to

connect to your NetWare server. The Installation Program

decompresses and copies all the required files.

If you are installing manually, without the Intel Installation

Program (under MS-DOS or Windows 3.x) you must first

decompress the VLM files by running the MS-DOS batch file

DCOMPVLM.BAT from the Network Drivers Disk, as follows:

DCOMPVLM [PATH]

where [path] is the directory for NetWare files (usually

C:\NWCLIENT). DCOMPVLM will decompress and copy all

required files to the designated directory.

If you need NETX shell support, contact your System Adminis-

trator.

Windows 3.x/MS-DOS Installation 4-27

SunSoft PC-NFS (version 3.5)

NDIS 2.0 Driver

1 Run the Intel Installation Program from the Installation Disk.

2 Choose SunSoft PC-NFS from the Select Network Operating

System screen.

3 Follow the prompts to complete the Intel installation.

4 Install PC-NFS for Ethernet according to instructions in the PC-

NFS documentation. Choose NDIS setup, and follow the

instructions to complete the setup. Note the prompt that tells you

that further manual modifications will have to be made.

5 Reboot the computer. You will see some error messages. Disregard

them and continue with these instructions.

6 Rename the file PROTOCOL.NFS in the C:\LANMAN directory

to PROTOCOL.INI. Use an text editor to edit the

PROTOCOL.INI file as follows:

Replace the items

[YOUR-MAC-MODULE]

DRIVERNAME = YOURMAC$

OPTION1 = VALUE1 ETC.

[NFS-NDIS]

DRIVERNAME = NFSLINK1

BINDINGS = YOUR-MAC-MODULE

with

[INTELNET]

DRIVERNAME = INTEL$

[NFS-NDIS]

DRIVERNAME = NFSLINK$

BINDINGS = INTELNET

7 Copy M16BNDIS.EXE from the C:\INTEL\M16B directory to

the C:\LANMAN directory.

8 Use a text editor to insert the following lines in your CONFIG.SYS

file:

4-28 PRO/100 LAN+Modem PC Card User’s Guide

DEVICE=C:\LANMAN\M16BNDIS.EXE

between the two lines

DEVICE=C:\LANMAN\PROTMAN.SYS

DEVICE=C:\LANMAN\NFS-NDIS.SYS

as follows:

DEVICE=C:\LANMAN\PROTMAN.SYS

DEVICE=C:\LANMAN\M16BNDIS.EXE

DEVICE=C:\LANMAN\NFS-NDIS.SYS

9 Verify that your AUTOEXEC.BAT file contains a line that reads

C:\LANMAN\NETBIND

before the line that reads

NET INIT

10 Configure PC-NFS options according to your PC-NFS documenta-

tion, and reboot the computer.

Ungermann-Bass Net/One for DOS

NDIS 2.0 Driver

The PRO/100 PC Card is supported on Ungermann-Bass Net/One LAN

Manager and MS-NET networks. There are two NDIS driver packages

available from UB: XNS BNS/NDIS and TCP BNS/NDIS. These

packages, used with a Intel NDIS driver, provide files that support DOS

workstations. They are available from UB and authorized UB representa-

tives.

Ungermann-Bass Net/One LAN Manager version 2.1

Installation

1 Begin installation of LAN Manager 2.1 using “setup.”

2 When prompted to select the available network adapter driver,

choose “Other Driver.”

3 When prompted, insert the Intel Network Drivers Disk.

4 Select “Intel EtherExpress™ PRO/100 LAN+Modem PC Card”

from the menu.

Windows 3.x/MS-DOS Installation 4-29

5 Continue with the installation until it is completed.

6 Following the UB instructions, modify your CONFIG.SYS file by

adding the following lines:

For DOS:

DEVICE = [PATH]M16BNDIS.EXE

where [path] is the drive and directory in which you installed your

network operating system.

7 Use a text editor to modify your PROTOCOL.INI file as follows:

• For each protocol that you want to bind, set the protocol

definition area of the PROTOCOL.INI file to:

BINDINGS = UBLOOP

• At the end of the file, add the following fragments:

[UBLOOP]

DRIVERNAME = UBLOOP$

BINDINGS = INTELNET

;INTEL ADAPTER

[INTELNET]

DRIVERNAME = INTEL$

8 Reboot the PC.

Wollongong PathWay Access for DOS

NDIS and ODI Drivers

Wollongong PathWay Access for DOS can be installed using Intel NDIS

or ODI drivers. Installation instructions for both types of driver are

provided below. For information on which driver is appropriate for your

network environment, refer to the Wollongong PathWay Access for DOS

documentation.

Wollongong PathWay NDIS Installation

1 Run the Installation Program from Intel Disk 1, Installation Disk.

2 Choose Wollongong PathWay Access from the Select Network

Operating System screen.

4-30 PRO/100 LAN+Modem PC Card User’s Guide

3 Follow the prompts to complete the Intel segment of the installa-

tion.

4 Install PathWay Access for DOS Kernel and Drivers programs

according to the instructions in the PathWay Access for DOS

manual. Before rebooting the PC, continue with the following steps.

5 Use a text editor to modify the CONFIG.SYS file. After the

statement that reads

DEVICE=C:\PATHWAY\PWTCP.SYS

add the lines

DEVICE=\PATHWAY\[PROTMAN FILE] /I:C:\PATHWAY

DEVICE=\PATHWAY\M16BNDIS.EXE

where [PROTMAN FILE] is equal to the PROTMAN2.EXE or

PROTMAN.EXE file that is located in your PATHWAY directory.

(Refer to the Wollongong PathWay Access for DOS manual for

information regarding the differences between these two files.)

6 Copy the file M16BNDIS.EXE from C:\INTEL\M16B directory

to the PATHWAY directory on your hard disk or boot disk.

7 Continue with the “custom” instructions in the PathWay Access for

DOS manual.

8 Reboot the PC.

Wollongong PathWay ODI Installation

1 Run the Intel Installation Program from the Installation Disk.

2 Choose Wollongong PathWay Access from the Select Network

Operating System screen.

3 Follow the prompts to complete the Intel segment of the installa-

tion.

4 Install PathWay Access for DOS Kernel and Drivers programs

according to the instructions in the PathWay Access for DOS

manual. Before rebooting the PC, perform the following steps.

5 Run the MS-DOS batch file DCOMPVLM.BAT from the Network

Drivers Disk, as follows:

DCOMPVLM PATHWAY

DCOMPVLM.BAT will decompress and copy all required files

Windows 3.x/MS-DOS Installation 4-31

from the Intel Network Drivers Disk to the PATHWAY directory

on your hard disk or boot disk. (The files are LSL.COM,

M16BODI.COM, IPXODI.COM, VLM.EXE, and NET.CFG.)

6 Change to the PATHWAY directory and load the software in the

following order:

LSL

M16BODI

IPXODI

VLM

(ONLY IF USING NOVELL NETWARE)

7 Load the Wollongong file ODI.EXE.

8 Continue with the instructions in the PathWay Access for DOS

manual.

9 Reboot the PC.Windows 3.x

Windows 3.x Modem Configuration Notes

The PRO/100 PC Card doubles as a LAN card and fax/modem. As a

modem, the PRO/100 PC Card features Hayes and Microcom compatibil-

ity and the latest in data transmission, data compression, and error control

techniques. It can be used with most standard communications and fax

software packages.

Note

Unless Card and Socket Services are being used under Windows

3.x, the PRO/100 PC Card requires that a LAN+modem driver

(M16BODI.COM, M16BNDIS.EXE, or M16BPD.COM) or a

modem-only driver (IMENABLE.COM) be loaded before the

modem can be used.

For more detailed modem information, see Chapter 6. Modem Reference

in this User’s Guide.

4-32 PRO/100 LAN+Modem PC Card User’s Guide

Using Network or Modem

Communications under Windows 3.x

All Intel Windows 3.x network drivers initialize both the LAN and the

modem. When a network driver is loaded, the modem driver is automati-

cally initialized.

Using Modem Communications Only under Windows

3.x

If you want to use the modem under Windows 3.x without loading a

network driver, and you are NOT using Card and Socket Services, reboot

the computer and run the utility IMENABLE.COM (found in the root

directory of Intel Disk 2, Network Drivers Disk) from the DOS prompt

before launching Windows or your communications program:

IMENABLE

Installing Communications and Fax Software

The PRO/100 PC Card is compatible with most popular communications

and fax software packages (see Chapter 5. Utilities and Applications for

application-specific information).

Running Windows Communications and Fax Software

Windows 3.x-based fax and communications programs can be started

immediately once the modem has been initialized.

Running DOS Communications and Fax Software

DOS-based communications software should be run from a DOS prompt

without Windows loaded. DOS software can also be run in a DOS box

with Windows loaded.

Windows 3.x/MS-DOS Installation 4-33

COM Ports, IRQs, and I/O Base Addresses

Automatic COM Port Detection

The PRO/100 PC Card drivers will automatically configure a COM port

on the system. The driver scans the BIOS table for the first unused COM

port, then checks to see if the corresponding IRQ is in use. If it is, it

moves to the next available COM port.

This process takes precedence over the network resources. If you specify a

network IRQ that is the same as the first available COM IRQ (3 or 4), the

driver will respond with an error.

To force a COM port, use the COMx keyword described in the following

heading. If you do not want a COM port, add the NOCOM keyword to

your configuration file or command line.

Manually Setting COM Port, Interrupt, and I/O Address

Values

Use the COMx keyword to manually specify which COM port the PRO/

100 PC Card should use when providing erial port emulation for modem

operations. Values for x can be 1, 2, 3, or 4. Each of these settings also

activates a specific set of predefined values for I/O address and interrupt

level, as follows:

PORT

COM1

COM2

COM3

COM4

IRQ

IOADDRESS

03F8

02F8

03E8

02E8

Do not select a COM port that is currently used by any other system

device, such as the PC Card interface itself, or a mouse or trackball.

Note

Configure your communications software to the COM port you

selected with the COMx keyword.

By default the LAN drivers will select the first open COM port. You can

add the COMx keyword and a port number to the LAN driver configura-

4-34 PRO/100 LAN+Modem PC Card User’s Guide

tion to activate serial port emulation. The COMx keyword can also be

stated on the command line with the modem-only driver

IMENABLE.COM.

Use the keywords COMIRQ and COMBASE to override the values set

with COM1, COM2, COM3, or COM4 in case of a conflict between LAN

and modem settings.

Sample NET.CFG File (ODI Driver) with COM Port Setting

LINK DRIVER M16BODI

INT 10

PORT 280

MEM D2000

COM3

Sample PROTOCOL.INI (NDIS Driver) with COM Port

Setting

[INTELNET]

DRIVERNAME=INTEL$

IRQ=10

IOADDRESS=0X320

MEM=0XD2000

MODE=IO

COM4

Sample Packet Driver Command Line with COM Port

Setting

M16BPD COM3 MEM=D8000

Sample IMENABLE.COM Command Line

IMENABLE COM3 MEM=D8000

Windows 3.x/MS-DOS Installation 4-35

Changing Interrupt or I/O Address Settings

The COMIRQ keyword is used to override the predefined interrupt value

for a specific COM port in case of a conflict between LAN and modem

settings. It can also be used with COMBASE to select a user-defined

COM port. Default is keyword not used. Setting is a decimal value which

must be different from the value used with the INTERRUPT keyword.

The COMBASE keyword can be used to override the predefined I/O

port value for a specific COM port in case of a conflict between LAN and

modem settings. It can also be used with COMIRQ to select a user-

defined COM port. The default condition is “keyword not used.”

Parameter setting is a hexadecimal value in the range 248 to 3F8 which

must be different from the value used with the IOADDRESS or PORT

keyword. Serial emulation mode requires 8 addresses.

The SHAREIRQ keyword is only valid when no Card Services are being

used. It instructs the driver that the modem and LAN interfaces must

share the IRQ line. State this keyword to configure the interface for one

physical IRQ and one logical IRQ, instead of the two separate physical

IRQs normally used by the PC Card controller.

Preventing Memory Conflicts

Memory allocation conflicts can cause the Intel driver to fail to load. The

PRO/100 PC Card requires an 8K memory block located between C000

and EFFF, with a default starting address of D2000.

Some computers require that a different address be used. To change the

memory address at which the Intel driver loads, use the MEMORY or

MEM keyword in the driver configuration file or on the driver command

line.

Memory Manager Exclusions

When using a memory manager such as EMM386, the memory manager

will try to control the upper memory blocks where the Intel driver

normally loads. To prevent conflicts, add a statement to the EMM386

command line excluding an 8K memory block between C000 and EFFF

for the Intel driver. For example,

DEVICE=C:\PATH\EMM386.EXE NOEMS X=CC00-CDFF

4-36 PRO/100 LAN+Modem PC Card User’s Guide

Here are some examples of MEMORY keyword settings and the corre-

sponding 8K exclusion:

Configuration

Keyword Setting

Exclusion

NET.CFG

MEM CC000

X=CC00-CDFF

PROTOCOL.INI MEMORY=D4000 X=D400-D5FF

Command Line

MEMORY=C8000 X=C800-C9FF

Notes

Memory settings used to configure the PRO/100 PC Card

always use 5 digits. Memory settings on the EMM386 command

line only require 4 digits.

With Card and Socket Services, the memory exclusion is

generally much larger than that required without them. This

exclusion range should not be reduced.

Windows and EMM386

If you are using EMM386 and Windows, you should add an

EMMEXCLUDE= line to the [386enh] section of the SYSTEM.INI file.

The exclusion range should match the exclusion on the EMM386 line.

If you are not using EMM386, but are using Windows, then you MUST

add an EMMEXCLUDE= statement to the [386enh] section of the

SYSTEM.INI file. The exclusion range must match the memory window

the PRO/100 PC Card is using.

Windows 3.x Modem Driver Settings

The modem utility IMENABLE.COM searches for an available COM

port or one specified by the user and configures the Intel adapter hard-

ware accordingly.

Modem Driver Configuration Notes

If you want to use the modem without loading a network driver, and you

are not using Card and Socket Services or the equivalent under Microsoft

Windows 95 or NT, you have to load the modem driver

IMENABLE.COM, supplied on Disk 2. Network Drivers Disk. (If you

load a network driver such as M16BNDIS, M16BODI, or M16BPD, you

Windows 3.x/MS-DOS Installation 4-37

do not need IMENABLE.COM because the network drivers also initialize

the modem.)

Reboot the computer and run IMENABLE.COM from the DOS prompt

before launching Windows or a communications program.

IMENABLE.COM Keywords

KEYWORD

DEFAULT

VALID VALUES

COMX

AUTO

(X = 1, 2, 3, OR 4)

COMIRQ

NOT USED

AUTO

(3 TO 15)

COMBASE

IOWAITSTATES=

MEMORY=

MEMWAITSTATES=

SLOT=

(0X248 TO 0X3F8)

(1, 2, OR 3)

0XD2000

AUTO

(0XC0000 TO 0XE0000)

(1, 2, OR 3)

AUTO

(HARDWARE DEPENDENT)

(DISABLES IMENABLE)

OFF

NOT USED

Modem Driver Example

A typical sequence for loading the modem driver IMENABLE.COM with

default configuration settings is as follows:

IMENABLE.COM COMX

where COMx is a COM port value such as COM3 or COM4. If other

nondefault configuration settings are used, these must also be stated on

the IMENABLE.COM command line. For example,

IMENABLE COM4 COMBASE=0X320 COMIRQ=10

Windows 3.x Network Driver Parameters

The following paragraphs present configuration guidelines for each of the

driver types: NDIS, ODI, and packet. These guidelines are followed by a

comprehensive “keyword” reference section and a list of error messages.

All of the drivers described here automatically detect the speed of the

network to which the adapter is attached (10Mbps or 100Mbps), unless

otherwise noted. Speed can also be specified with the LINESPEED

keyword.

4-38 PRO/100 LAN+Modem PC Card User’s Guide

ODI Settings (for driver M16BODI.COM)

Custom parameters for networks using the ODI driver can be entered

manually, using an ASCII editor, in the NET.CFG file.

DOS ODI Driver Configuration Notes (M16BODI.COM)

The ODI driver M16BODI.COM conforms to the “Novell ODI Specifi-

cation: 16-bit DOS Client HSMs.” It is a DOS-based

terminate-and-stay-resident (TSR) program. The driver will configure itself

according to the options specified in the NET.CFG file. This file is

supplied on Disk 2, Network Drivers Disk and must be present in the

same directory as the ODI driver. Files required for using

M16BODI.COM are

M16BODI.INS

NET.CFG

Intel installation information file

Network configuration file

Intel ODI driver

M16BODI.COM

Most installations will be able to use the settings detected by the driver. If

any parameters need to be changed, use an ASCII text editor to open and

modify the NET.CFG file and insert the appropriate keywords and values

after the line

LINK DRIVER M16BODI

Parameters can also be implemented on the command line. Keyword

syntax can be found below. Keywords are not case sensitive. A Keyword

Alphabetical Reference follows the discussion of keyword syntax.

NET.CFG Example

LINK DRIVER M16BODI

INT 5

PORT 280

MEM D2000

Windows 3.x/MS-DOS Installation 4-39

M16BODI.COM Keywords

KEYWORD

DEFAULT

VALID VALUES

(X = 1, 2, 3, OR 4)

(3 TO 15)

COMX

AUTO

COMIRQ=

COMBASE=

INTERRUPT

IOADDRESS

IOWAITSTATES

LINESPEED

LINKDISABLE

(0X248 TO 0X3F8)

(3 - 15)

(240 - 380)

(1 - 3)

AUTO

(10 OR 100)

(NO KEYWORD = LINK INTEGRITY ENABLED)

LINK DRIVER M16BODI (REQUIRED FIRST ITEM IN NET.CFG)

MEMORY

AUTO

(C0000 - EE000)

(1 - 3)

MEMWAITSTATES

MODE

MEM

(MEM OR IO)

NOCHECK

(NO KEYWORD = ADAPTER RESOURCE VERI-

FICATION ENABLED)

NOCOM

NOEARLYRX

NOEARLYTX

NOLED

(NO KEYWORD = MODEM ENABLED)

(NO KEYWORD = EARLY RECEIVE ENABLED)

(NO KEYWORD = EARLY TRANSMIT ENABLED)

(NO KEYWORD = LEDS ENABLED)

(COMMAND LINE ONLY: SHOW RESIDENT LAN

DRIVERS)

SHAREIRQ

SOCKET

AUTO

(1 - 4)

NOT USED

(COMMAND LINE ONLY:

UNLOAD M16BODI)

WORDSIZE

(8 OR 16)

ODI Driver Example

A typical load sequence for the ODI driver M16BODI.COM in a

NetWare environment would be

LSL

M16BODI

IPXODI

VLM

4-40 PRO/100 LAN+Modem PC Card User’s Guide

NDIS 2.0.1 Settings (for driver

M16BNDIS.EXE)

Custom parameters for the NDIS driver can be entered manually, using an

ASCII editor, in the PROTOCOL.INI file.

NDIS 2.0.1 DOS Driver Configuration Notes

The DOS NDIS driver M16BNDIS.EXE conforms to the Microsoft

Network Driver Interface Specification (NDIS) version 2.0.1. It is a DOS-

based executable terminate-and-stay-resident (TSR) program that will

configure itself according to the options specified in the PROTOCOL.INI

file, which is supplied on Disk 2. Network Drivers Disk.

The files required for using M16BNDIS.EXE are:

PROTOCOL.INI

M16BDOS.NIF

M16BNDIS.EXE

Configuration and binding informa

tion file

Intel installation file for Microsoft

LAN Manager

Intel DOS NDIS 2.0.1 driver

Most installations will be able to use the settings detected by the driver. If

any parameters need to be changed, use an ASCII text editor to modify

the PROTOCOL.INI file with the appropriate keywords and values.

Keyword syntax for PROTOCOL.INI can be found below. Keywords are

not case sensitive, and can be abbreviated to a unique sequence of initial

characters (for example, IN for INTERRUPT, IO for IOADDRESS). A

Keyword Alphabetical Reference follows the keyword listings.

PROTOCOL.INI Example

[INTELNET]

DRIVERNAME=INTEL

MEM=0XD2000

MODE=IO

Windows 3.x/MS-DOS Installation 4-41

NDIS 2.0.1 Keywords (M16BNDIS.EXE)

KEYWORD

DEFAULT

VALID VALUES

(X = 1, 2, 3, OR 4)

(3 TO 15)

COMX

AUTO

COMIRQ=

COMBASE=

AUTO

(0X248 TO 0X3F8)

DRIVERNAME=INTEL$ (REQUIRED FIRST ITEM IN PROTOCOL.INI)

INTERRUPT=

IOADDRESS=

IOWAITSTATES=

LINESPEED=

LINKDISABLE

MEMORY=

AUTO

(3 - 15)

(240 - 380)

(1 - 3)

AUTO

(10 OR 100)

(NO KEYWORD = LINK INTEGRITY ENABLED)

AUTO

(C0000 TO EE000)

(1 - 3)

MEMWAITSTATES=

MODE=

MEM

(MEM OR IO)

NOCHECK

(NO KEYWORD = ADAPTER RESOURCE VERI

FICATION ENABLED)

NOCOM

(NO KEYWORD = MODEM ENABLED)

NOEARLYRX

NOEARLYTX

NOLED

(NO KEYWORD = EARLY RECEIVE ENABLED)

(NO KEYWORD = EARLY TRANSMIT ENABLED)

(NO KEYWORD = LEDS ENABLED)

SHAREIRQ

SOCKET=

WORDSIZE=

AUTO

(1 - 4)

(8 OR 16)

Packet Driver Settings (for driver

M16BPD.COM)

Packet driver parameters must be stated on the M16BPD.COM command

line when running the packet driver.

Packet Driver Configuration Notes

The Intel packet driver M16BPD.COM conforms to FTP Software’s

public domain packet-driver specification. It is a DOS-based terminate-

and-stay-resident (TSR) program. The driver file M16BPD.COM is located

in the \PKTDRV directory on Disk 2, Network Drivers Disk.

4-42 PRO/100 LAN+Modem PC Card User’s Guide

Refer to your network documentation for instructions on how to install

the packet driver with your network.

Keywords are not case sensitive, and can be abbreviated to a unique

sequence of initial characters (for example, IN for INTERRUPT).

Packet Driver Keywords

KEYWORD

DEFAULT

AUTO

VALID VALUES

(X = 1, 2, 3, OR 4)

(3 TO 15)

COMX

COMIRQ=

COMBASE=

INTERRUPT=

IOADDRESS=

IOWAITSTATES=

LINESPEED=

LINKDISABLE

MEMORY=

(0X248 TO 0X3F8)

(3 - 15)

(240 - 380)

(1 - 3)

AUTO

(10 OR 100)

(NO KEYWORD = LINK INTEGRITY ENABLED)

AUTO

(C0000 - E8000)

(1 - 3)

MEMWAITSTATES=

MODE=

MEM

(MEM OR IO)

NOCHECK

(NO KEYWORD = ADAPTER RESOURCE VERI

FICATION ENABLED)

NOCOM

(NO KEYWORD = MODEM ENABLED)

(NO KEYWORD = EARLYRX ENABLED)

(NO KEYWORD = EARLYTX ENABLED)

(NO KEYWORD = LEDS ENABLED)

NOEARLYRX

NOEARLYTX

NOLED

SHAREIRQ

SINT

(60 - 80)

(1 - 4)

SOCKET=

WORDSIZE=

AUTO

(8 OR 16)

Packet Driver Example

A typical sequence for loading the packet driver M16BPD.COM with

default configuration settings is as follows:

M16BPD

ETHDRV

Windows 3.x/MS-DOS Installation 4-43

If nondefault configuration settings are used, these must be stated on the

M16BPD.COM command line. For example,

M16BPD IOADDRESS=320 INT=7

ETHDRV

Driver Keyword Alphabetical Reference

displays a summary of command line options.

COMx

specifies which COM port the PRO/100 PC Card

should use when providing serial port emulation

for modem operations. Values for x can be 1, 2, 3,

or 4. Each of these values instructs the driver to

use pre-defined values for I/O address and

interrupt level, and to enable the specified I/O

address in the COM port BIOS table. The modem

driver IMENABLE.COM defaults to COM3. Use

the keywords COMIRQ and COMBASE to

override the values set with COM1, COM2,

COM3, or COM4 in case of a conflict between

LAN and modem settings.

COMBASE

can be used to override the pre-defined I/O port

value for a specific COM port in case of a conflict

between LAN and modem settings. It can also be

used with COMIRQ to select a user-defined COM

port. Default is no keyword. Parameter setting is a

hexadecimal value in the range 248 to 3F8 which

must be different from the value used with the

IOADDRESS or PORT keyword. Serial emulation

mode requires 8 addresses.

COMIRQ

is used to override the pre-defined interrupt value

for a specific COM port in case of a conflict

between LAN and modem settings. It can also be

used with COMBASE to select a user-defined

COM port. Default is no keyword. Parameter

setting is a decimal value which must be different

from the value used with the INTERRUPT

keyword.

4-44 PRO/100 LAN+Modem PC Card User’s Guide

FRAME

(ODI) designates support for multiple Ethernet

frame types. One or more types can be used. Refer

to your NetWare documentation for more

information. The Intel ODI driver’s default frame

type is 802.2, but the NET.CFG file supplied with

the ODI driver on Disk 2, Network Drivers Disk

sets both 802.2 and 802.3. Therefore if your

network’s frame type is 802.3, you must use Intel’s

NET.CFG with the ODI driver.

INTERRUPT

specifies a LAN interrupt to use. It requires a

decimal value designating the PRO/100 PC Card

port hardware interrupt (for example, INT 5 or

INT 7). Default (if parameter not specified) is 5.

Any value supported by the PC Card hardware can

be used.

INTERRUPTNUMBERSee INTERRUPT.

IOADDRESS

specifies the LAN I/O address to use, in hexadeci-

mal notation. Default address is 320.

IOBASEADDRESS see IOADDRESS.

IOWAITSTATES specifies the number of wait states that should be

added to I/O accesses to the card. Values are a

decimal number from 1 to 3. On some machines it

may be necessary for the driver to run with I/O

waitstates. By default, the driver will attempt to

automatically configure this parameter. The

keyword is provided as a troubleshooting aid.

LINKINTEGRITY ON or OFF. See LINKDISABLE.

LINKDISABLE

disables the link integrity check on the network

twisted pair cabling (for operation with non-IEEE

10BASE-T networks such as StarLAN 10).

Without the LINKDISABLE keyword in the

driver command line, the driver defaults to link

integrity ENABLED.

Windows 3.x/MS-DOS Installation 4-45

MEMORY

specifies the memory location to use. It is specified

in hexadecimal notation and is not a segment

value. Specify the full address for all drivers. For

example, D2000, not D200. The PRO/100 PC

Card uses 4 Kbytes of memory (1000 hexadecimal)

for the LAN. Use the MODE IO setting to disable

MEMORY MODE. Default is D2000. Possible

values are C0000 through E0000.

MEMORYBASEADDRESS

see MEMORY.

MEMWAITSTATESspecifies the number of wait states that should be

added to memory accesses to the card. Values are

decimal 1 to 3. On extremely fast machines it may

be necessary for the driver to run with waitstates.

By default, the driver will attempt to automatically

configure this parameter. The keyword is provided

as a troubleshooting aid.

MODE

specifies whether to run the network in memory-

mapped or I/O mode. Values are the ASCII

strings MEMORY or IO. The default setting is

MEM. Set this keyword to IO to disable requests

for memory-mapped mode on systems that only

support an I/O driven card.

NOCHECK

NOCOM

disables verification of adapter resources. This

keyword is intended to be used as a troubleshoot-

ing tool.

the PRO/100 PC Card driver will configure a

COM port by default. The NOCOM keyword can

be used to defeat this feature. If the keyword is not

used, the modem is enabled. LAN operations are

not affected.

NOEARLYRX

disables Advanced Look-ahead Pipelining features

of the PRO/100 PC Card. You may need this

keyword for NDIS version 2.01 drivers which do

not fully support the “early RX” feature.

4-46 PRO/100 LAN+Modem PC Card User’s Guide

NOEARLYTX

disables early transmit features of the PRO/100

PC Card. Try using this keyword if you are

experiencing a large number of transmit overruns.

NOLEDS

PORT

turns off network LED indicators on LAN adapter

cables to conserve battery power.

(ODI) specifies the LAN I/O address to use, in

hexadecimal notation. Default address is 320.

SHAREIRQ

is optional when no Card Services are being used.

It instructs the driver that the modem and LAN

interfaces must share the IRQ line. State this

keyword to configure the interface for one physical

IRQ and one logical IRQ, instead of the two

separate physical IRQs normally used by the PC

Card controller.

SINT

(Packet Driver) is number from hexadecimal 60 to

80 designating a software interrupt. Default is 60.

SLOT

Same as SOCKET but used with

IMENABLE.COM.

SOCKET

forces the driver to look in the selected socket

specifically for a PRO/100 PC Card. If no

keyword is stated, the driver will scan all PC Card

slots looking for the right card. Valid values are

from 1 to the number of PC Card slots supported

by the computer being used. This keyword may be

useful if you have a memory card or other PC Card

device in socket 1 and a PRO/100 PC Card in

socket 2. Then set the keyword to SOCKET=2 in

your configuration file or on the command line.

WORDSIZE

this parameter specifies the size of the data path

for the LAN controller. Values are 8 or 16 decimal.

Default is 16. Since the modem always uses an 8-

bit data path, this keyword does not affect the

modem.

Windows 3.x/MS-DOS Installation 4-47

Error Messages for Windows 3.x and

MS-DOS drivers

Except as noted, these messages are specific to the PRO/100 PC Card.

For an explanation of other messages that may appear on the screen, see

your computer and network operating system documentation.

A PCMCIA card was not detected

If the SOCKET keyword was stated, then no PC Card was detected in the

slot specified. If the SOCKET keyword was not used, then no PC Card

was detected in any slot.

An invalid I/O address was specified

The PRO/100 PC Card requires 32 consecutive I/O locations. This

message indicates that the I/O address specified does not start on a 32-

byte boundary. Examples of valid I/O addresses, in hexadecimal notation,

are 300, 320, 240. Examples of invalid I/O addresses are 301, 325, 247.

M16BODI only supports the BUS ID PC Card, not the selected

BUS ID. Either delete the BUS ID keyword from the NET.CFG file

or change its value to 3.

This message applies only to the ODI driver. Do not use the keyword

BUS ID in the ODI NET.CFG file. If you do use it, you must set the

value to 3.

Network Controller running in 8-bit mode

The Network Interface Controller (NIC) has been forced to run in 8-bit

mode with the keyword WORDSIZE set at 8 (default is 16-bit mode).

This option is used when the PC Card hardware does not support 16-bit

mode.

Network Controller running in I/O mode

The Network Interface Controller (NIC) has been forced to run in I/O-

only mode with the keyword MODE set at IO (default is MEM). This

option is used when the PC Card hardware does not support perfor-

mance-enhancing memory-mapped I/O mode.

4-48 PRO/100 LAN+Modem PC Card User’s Guide

The card is unreadable, possible memory conflict

The Card Information Structure (CIS) of the PC Card was unreadable.

This could be a result of failure to exclude the selected memory range

from the memory managers loaded on the machine. Either exclude a 8K

memory range, select a memory range that has already been excluded, or

include the NOCHECK keyword in the configuration file.

Please specify a different interrupt for the modem

The LAN adapter and modem cannot be configured for the same

interrupt. Either select a different modem interrupt (using the COMIRQ

keyword or a different COM port value), or select a different LAN

interrupt (using the INTERRUPT keyword).

The COMBASE keyword is required in this configuration

If the COMIRQ keyword has been specified, but COM1, COM2, COM3,

or COM4 has NOT been specified, the COMBASE keyword must be

specified with an appropriate value.

The COMIRQ keyword is required in this configuration

If the COMBASE keyword has been specified, but COM1, COM2,

COM3, or COM4 has NOT been specified, the COMIRQ keyword must

be specified with an appropriate value.

The Network Controller is not responding

A PRO/100 PC Card was detected, but subsequent attempts to initialize

the network controller failed. Try setting the WORDSIZE parameter to 8.

Please specify a decimal number for the INTERRUPT keyword

This message applies only to the NDIS 2.0 Driver. The value specified

under the INTERRUPT keyword in the PROTOCOL.INI file must be a

decimal not a hexadecimal number.

Windows 3.x/MS-DOS Installation 4-49

Please specify a hexadecimal number for the IOADDRESS keyword

This message applies only to the NDIS 2.0 Driver. The value specified

under the IOADDRESS keyword in the PROTOCOL.INI file must be a

hexadecimal number.

Please specify a hexadecimal number for the MEMORY keyword

This message applies only to the NDIS 2.0 Driver. The value specified

under the MEMORY keyword in the PROTOCOL.INI file must be a

hexadecimal number.

Please specify either 8 or 16 for the WORDSIZE keyword

This message applies to both the ODI and NDIS 2.0 drivers. The value

specified under the WORDSIZE keyword in the NET.CFG or

PROTOCOL.INI file must be either 8 or 16.

Please specify a nonzero decimal number for the SOCKET keyword

This message applies to both the ODI and NDIS 2.0 drivers. The value

specified under the SOCKET keyword in the NET.CFG or

PROTOCOL.INI file must be a decimal number other than zero.

Please specify 0, 1, 2, or 3 for the MEMWAITSTATES keyword

This message applies to both the ODI and NDIS 2.0 drivers. The value

specified under the MEMWAITSTATES keyword in the NET.CFG or

PROTOCOL.INI file must be either 0, 1, 2, or 3.

Please specify 0, 1, 2, or 3 for the IOWAITSTATES keyword

This message applies to both the ODI and NDIS 2.0 drivers. The value

specified under the IOWAITSTATES keyword in the NET.CFG or

PROTOCOL.INI file must be either 0, 1, 2, or 3.

The memory test failed - Please select a different memory address

The memory test will write data into the memory, read them back, and

verify if they are the same. In this case, the memory written and read back

were found to be different.

4-50 PRO/100 LAN+Modem PC Card User’s Guide

The I/O test failed - Please select a different I/O address

The driver failed the I/O test. Try a different I/O address.

The IRQ test failed - Please select a different IRQ

The driver failed the IRQ test. Try a different IRQ address.

Please specify either IO or MEM for the MODE keyword

This message applies to both the ODI and NDIS 2.0 drivers. The value

specified under the MODE keyword in the NET.CFG or

PROTOCOL.INI file must be either IO or MEM.

Please specify a decimal number for the COMIRQ keyword

This message applies to both the ODI and NDIS 2.0 drivers. The value

specified under the COMIRQ keyword in the NET.CFG or

PROTOCOL.INI file must be a decimal number.

Please specify a hexadecimal number ending in 8 for the

COMBASE keyword

This message applies to both the ODI and NDIS 2.0 drivers. The value

specified under the COMBASE keyword in the NET.CFG or

PROTOCOL.INI file must be a hexadecimal number in the range 248 to

3F8.

No standard COM ports available. Please use custom COM port

(COMIRQ, COMBASE)

This message applies to both the ODI and NDIS 2.0 drivers. All COM

ports (COM1 - COM4) are being used. Create a custom COM port by

adding the COMIRQ and COMBASE keywords, with assigned values, to

the NET.CFG or PROTOCOL.INI file.

The selected COM IRQ is in use by another device

The IRQ value set for the COM port is already in use by another device.

Assign a different IRQ value for the COM port.

Windows 3.x/MS-DOS Installation 4-51

The selected COM port already exists

The COM port is already in use by another device. Assign a different I/O

port for the COM port.

Windows 3.x Troubleshooting

Important

For application notes covering installation and configuration

issues pertaining to specific computers, Card and Socket

Services, and communications software packages, see Chapter 5.

Utilities and Applications.

A driver failed to load, and I’m using Card

and Socket Services

Card and Socket Services are a set of drivers designed to support the PC

Card (PCMCIA) standard. These drivers are generally supplied by the

computer manufacturer. Among other functions they

• Hide the PCMCIA socket hardware implementation from the PRO/

100 PC Card driver.

• Control the allocation of resources (memory windows, I/O ports,

interrupts) to the PRO/100 PC Card.

Recommendations for Use of Card and Socket Ser-

vices with the PRO/100 PC Card.

A. If the memory manager EMM386.EXE is being used, verify that the

memory required for the PRO/100 PC Card has been excluded from use

by the memory manager in the CONFIG.SYS. The memory exclusion

required when using Card and Socket Services is generally larger than the

exclusion needed by the

PRO/100 PC Card alone. The safest setting when troubleshooting is to

“remark out” the entire “C” and “D” memory ranges, as follows:

DEVICE=C:\PATH\EMM386.EXE NOEMS X=C000-DFFF

4-52 PRO/100 LAN+Modem PC Card User’s Guide

After the driver has been successfully loaded, the memory exclusion may

be reduced through trial and error or in accordance with the Card and

Socket Services documentation. The system must be rebooted before the

revised settings take effect.

B. When the PRO/100 PC Card driver is loaded it either reads a configu-

ration file or uses command line parameters to determine which resources

it should use. The following is a list of driver types, driver file names, and

the configuration method used by each:

Type File Name

ODI M16BODI.COM reads NET.CFG configuration file

NDIS2 M16BNDIS.EXE reads PROTOCOL.INI configuration file

Packet M16BPD.EXE uses COMMAND LINE parameters

Test M16BTEST.EXE uses COMMAND LINE parameters

Configuration Method

C. Card and Socket Services will generally try to assign a set of resources

(interrupt, memory window, I/O window) to the PRO/100 PC Card. The

resources configured for the PRO/100 PC Card (in a configuration file or

on a command line) must match the resources assigned by Card and

Socket Services. If they do not, the driver will generally fail to load.

The way resources are assigned to the PC Card varies among Card and

Socket Services manufacturers. The following section provides guidelines

for the most popular Card and Socket Services. Review your Card and

Socket Services documentation. To use Card and Socket Services with the

PRO/100 PC Card, you must know what resources will be assigned by

Card and Socket Services, then specify the same resources when configur-

ing the PRO/100.

IBM

The following are the files generally loaded with IBM Card and Socket

Services.

DEVICE=C:\THINKPAD\IBMDSS01.SYS /S0=2

DEVICE=C:\THINKPAD\IBMDOSCS.SYS

DEVICE=C:\THINKPAD\DICRMU01.SYS /MA=C800-CFFF (/MA SHOULD

MATCH THE EMM386 EXCLUSION)

DEVICE=C:\THINKPAD\AUTODRV.SYS C:\THINKPAD\AUTODRV.INI (CALLED

A “GENERIC” CARD DRIVER)

Windows 3.x/MS-DOS Installation 4-53

The AUTODRV.INI file is used to assign resources to the PRO/100 PC

Card. The AUTODRV.INI file should be edited to read as follows:

ETHERNET.

CARDID=ETHER,CREDI

;OPTION=IGNORE (THE SEMICOLON IS REQUIRED)

PORT1=320, IRQ=5, MEMORY1=C800, WAITSTATE=1

The same resources should be specified in the PRO/100 PC Card driver

initialization file.

Phoenix

The Phoenix Card and Socket Services super client driver PCMSCD.EXE

should NOT be configured with the PCM.EXE program to support the

PRO/100 PC Card. Use the default setup and the following sequence of

commands in your CONFIG.SYS file.

DEVICE=C:\PCMPLUS3\PCMSS.EXE

DEVICE=C:\PCMPLUS3\PCMCS.EXE

DEVICE=C:\PCMPLUS3\PCMRMAN.SYS

DEVICE=C:\PMCPLUS3\PCMSCD.EXE (CALLED A “GENERIC” CARD DRIVER)

Be sure to verify that an EMM386 memory exclusion has been stated to

cover the region where the Intel card loads.

SystemSoft

The SystemSoft’s CardSoft Card and Socket Services are loaded in the

CONFIG.SYS file and generally include the following lines:

DEVICE=C:\CARDSOFT\SOCKET_SERVICES_DRIVER

(THIS FILE VARIES

BY MACHINE TYPE)

DEVICE=C:\CARDSOFT\CS.EXE

DEVICE=C:\CARDSOFT\CSALLOC.EXE C:\CARDSOFT\CSALLOC.INI

DEVICE=C:\CARDSOFT\CARDID.EXE (CALLED A “GENERIC” CARD DRIVER)

Resources assigned by CardSoft Card and Socket Services are controlled

by the files CSALLOC.INI and CARDID.INI. CSALLOC.INI contains a

list of resources available to Card and Socket Services. CARDID.INI

controls how resources will be assigned to specific types of cards. The

setting in the PRO/100 PC Card driver configuration file should match

4-54 PRO/100 LAN+Modem PC Card User’s Guide

the resources assigned by the LAN1xxxxxx keywords in the CARDID.INI

file. The LAN1MEMORYBASE2 entry can be ignored.

A driver failed to load, and I’m NOT using

Card and Socket Services

A. Verify that a block of memory for use by the PRO/100 PC Card has

been excluded from any memory manager being loaded. Memory manag-

ers are generally loaded in the CONFIG.SYS. The following example is

given for EMM386.EXE and a PRO/100 PC Card loading at its default

memory address of D2000:

DEVICE=C:\PATH\EMM386.EXE NOEMS X=D200-D3FF

B. Verify that power management has been disabled and the PCMCIA

socket is powered/enabled in the computer system’s CMOS setup. These

settings may not be present in all machines. Consult your computer

documentation for information on how to access and modify the system

setup.

C. Reboot the machine by turning off the power and turning it back on

again (cold boot). If the driver still fails to load, the cause is generally a

resource conflict. Common causes of resource conflicts include sound

systems, other PCMCIA adapters, and built in ROMs. The resources

required for a PRO/100 PC Card include a memory window (MEM

keyword), a LAN interrupt (INT keyword, and an I/O address

(IOADDRESS keyword). The default settings are indicated below.

Review your computer documentation to determine what resources are

available, or use a trial and error approach. The table below shows a

suggested trial and error sequence. If you use this method, be sure to add a

memory exclusion from C000-DFFF to the EMM386 line until a suitable

memory location has been found. Then the memory exclusion can be

reduced to an 8K window. Perform a cold boot between each trial to

ensure that the PRO/100 PC Card and PC Card sockets are completely

reset.

When the PRO/100 PC Card driver is loaded it either reads a configura-

tion file or uses command line parameters to determine which resources it

should use. The following is a list of driver types, driver file names, and

the configuration method used by each:

Windows 3.x/MS-DOS Installation 4-55

Type File Name

ODI

NDIS2 M16BNDIS.EXE reads PROTOCOL.INI configuration file

Packet M16BPD.EXE uses COMMAND LINE parameters

Test M16BTEST.EXE uses COMMAND LINE parameters

Configuration Method

M16BODI.COM reads NET.CFG configuration file

The default resources used by the PRO/100 PC Card when no other

setting is stated are:

MEMORY

AUTO

IRQ

IOADDRESS (NDIS)

PORT (ODI)

Troubleshooting combinations for driver configuration without Card and

Socket Services:

TRIAL

MEM

D2000

CC000

D2000

CC000

D2000

CC000

D2000

CC000

D2000

CC000

D2000

CC000

D2000

CC000

D2000

INT

IOADDRESS WORDSIZE

Default

320

340

4-56 PRO/100 LAN+Modem PC Card User’s Guide

If none of the above settings allows the driver to load, it may be necessary

to add an IOWAITSTATES=2 and MEMWAITSTATES=2 parameter to

the appropriate PRO/100 PC Card driver configuration file or command

line.

D. If the driver still fails to load after you’ve tried the combinations above,

your machine may require the use of Card and Socket Services. See the

preceding section.

E. Machine-specific notes:

IBM 755, 360, 355 - Set the keyword WORDSIZE=8 in your configura-

tion file or on the command line (WORDSIZE 8 for the ODI driver).

The driver loaded successfully, but I can’t

get on the network

A. Check all connections and verify that the cable drop is good (try a cable

that is known to work on another workstation).

B. Reboot by powering down the machine (cold boot). On some ma-

chines the PC Card controller chipset is not properly reset on a warm

boot, and this can cause network errors.

C. In a NetWare environment, verify that the frame type running on your

network server is the same as the FRAME type listed first in the

NET.CFG. If you are not sure what the correct Ethernet frame type is,

check with your system administrator. On a multi-server network, add a

preferred server statement to the NET.CFG.

D. There could be an interrupt conflict. Try loading the driver with a

different interrupt specified in the PRO/100 PC Card configuration file.

(This may also require some re-configuration of Card and Socket Services,

if they’re being used.)

E. If the problem persists, and you’re on a 10BASE-T network, try

patching directly into the hub. If the adapter works when plugged directly

into the hub, but not when attached via a longer cable run, verify that the

cable run length is within the IEEE 10BASE-T specification (100 meters).

If the cable length is correct, the adapter may be defective. Contact Intel

Customer Support.

Windows 3.x/MS-DOS Installation 4-57

The driver loaded, but my DOS modem

software won’t work

The PRO/100 PC Card is configured to add a second interrupt and I/O

address window in order to emulate a standard serial port interface. Use

the COMx keyword in your driver configuration file or as a command line

parameter to enable serial port emulation. If no COMx keyword is used,

the Intel driver will configure the PRO/100 PC Card at the first available

COM port.

Pre-set default resources corresponding to the COM port value are used,

as follows:

PORT IRQ

IOADDRESS

03F8

COM1

COM2

COM3

COM4

02F8

03E8

02E8

The default setting for the COM port address can be changed by the

COMBASE keyword. The default setting for the IRQ can be changed by

the COMIRQ keyword. A second keyword that affects interrupt usage is

SHAREIRQ. The SHAREIRQ keyword forces the modem side to share

the interrupt that the network side is using. The INT or INTERRUPT

keyword is used to set the interrupt the network side uses. Card and

Socket Services also has an effect on interrupt usage.

To troubleshoot the issues described above, proceed as follows:

1 Verify that the phone line is an analog phone line (the type used

with other modems and fax machines). Connecting the PRO/100

PC Card to a digital phone line will not damage the adapter, but is

not recommended.

2 Verify that the COMx keyword is present in the driver configuration

file or as a command line parameter as appropriate.

3 Observe the COM port number stated when the driver loads. It

should match the value of x assigned to the COMx keyword

(decimal values or 1, 2, 3, or 4) in the driver configuration file

(NET.CFG for M16BODI, PROTOCOL.INI for M16BNDIS) or

as a command line parameter for the packet driver (M16BPD) or

4-58 PRO/100 LAN+Modem PC Card User’s Guide

modem driver (IMENABLE). If they do not match, either there are

multiple COMx keywords listed in the file or there are multiple

configuration files.

4 Run Microsoft Diagnostics (MSD) and see if the COM port shows

up. On some machines MSD will not show what COM port was

configured for the PRO/100 PC Card. If it doesn’t, try the

following command:

ECHO ATDTNNNNNNN > COMX:

where nnnnnnn is a telephone you can hear ring, and x is the COM

port number. If the phone rings, this indicates that the COM port is

correctly configured and that the modem is able to dial.

If the COM port does not show up after running MSD, try

changing the x the COMx keyword to a different port value (start

with COM4 and try each value in sequence through COM1). Power

down the computer between trials.

The modem works in DOS, but not in

Windows

A. Verify that there are no communications/fax programs automatically

loading on Windows startup or running in the background.

B. If you are using Card and Socket Services, try the following:

1 In Windows, select Control Panel, Ports, and under Advanced, set

the selected COM port IOADDRESS to default, set the INTER-

RUPT LEVEL to the value specified by the INT or INTERRUPT

keyword in the LAN configuration file. You should also modify the

SYSTEM.INI file as follows: set COMxIRQ=y, where x is the

COM port the PRO/100 PC Card is configured as, and y is the

interrupt the LAN driver is using (as stated in the NET.CFG or

PROTOCOL.INI file).

2 If you are using the M16BODI driver and you receive a blue

warning screen stating that “A hardware interrupt has occurred,” try

adding the following section to the SYSTEM.INI file:

[VIPX]

VIRTUALIZE IRQX = OFF

where x is the interrupt number (in hexadecimal notation) used by

the M16BODI driver.

Windows 3.x/MS-DOS Installation 4-59

3 Turn computer power off and then on again (cold boot).

4 Start the Windows Terminal program in the Accessories group.

Select a COM port under the setting/communications options, click

OK to get back to the terminal screen. Change to modem command

mode and type AT, then press enter. If the modem responds with

OK, the trial configuration was correct.

5 In some cases an interrupt conflict will not be apparent until a

Windows mouse driver is loaded. It will then be necessary to cold

boot the machine, load the PRO/100 PC Card driver and re-start at

step 1. above.

C. Try disabling Card and Socket Services if they are enabled (see Item 2

of these Symptoms and Solutions).

D. If you are NOT using Card and Socket Services, try the following:

1 Verify the following entries in the Windows SYSTEM.INI file:

BOOT.

COMM.DRV=COMM.DRV

386ENH.

DEVICE=*VCD

You may need to remark out any *VCD.386 added by other

programs (IBMVCD.386, PCMVCD.386, SSVCD.386).

2 In Windows, go into the Control Panel, then Ports, and under the

Advanced options, set the selected COM port IOADDRESS and

INTERRUPT to default settings.

3 Exit Windows and turn computer off and on again (cold boot).

4 Start the Windows Terminal program in the Accessories group.

Select a COM port under the setting/communications options, click

OK to get back to the terminal screen. Change to modem command

mode and type AT, then press enter. If the modem responds with

OK, the trial configuration was correct.

5 In some cases an interrupt conflict will not be apparent until a

Windows mouse driver is loaded. It will then be necessary to cold

boot the machine, load the PRO/100 PC Card driver and re-start at

step 1. above.

4-60 PRO/100 LAN+Modem PC Card User’s Guide

I can't hear the modem

A. Be sure the computer speaker is enabled in the computer’s CMOS

setup utility.

B. To enable modem sound, include the following AT command in any

communications package modem initialization string:

or as a standalone command preceded by the letters AT:

ATM1

The PRO/100 PC Card does not have a built-in speaker. It relies on the

PC Card software to direct signals to the computer’s speaker. A few

computers do not properly direct the PRO/100 PC Card audio to the

system speaker. The modem will connect and operate normally, but no

sound will be heard. On some PCs you can set the speaker on or off or

change volume levels with a keyboard sequence. See your computer

documentation.

Computer-Specific Application Notes

(Windows 3.x)

If you are using Card and Socket Services and are experiencing problems,

find your computer in the list below and review the information provided.

The examples of Card and Socket Services driver stacks and

EMM386.EXE lines have been verified and are known to be reliable.

Sample Card and Socket Services configuration files and their known

problems are also supplied.

Ambra

DEVICE=C:\DOS\EMM386.EXE NOEMS X=D000-DCFF

DEVICE=C:\PCM3\CNFIGNAM.EXE /DEFAULT

DEVICE=C:\PCM3\PCMSS.EXE

DEVICE=C:\PCM3\PCMCS.EXE

DEVICE=C:\PCM3\PCMRMAN.SYS

DEVICE=C:\PCM3\PCMSCD.EXE

REM DEVICE=C:\PCM3\PCMATA.SYS

REM DEVICE=C:\PCM3\PCMFFCS.EXE

Windows 3.x/MS-DOS Installation 4-61

REM DEVICE=C:\PCM3\DBLFALSH.EXE

REM DEVICE=C:\PCM3\MS-FLASH.SYS

The configuration above will work with the PRO/100 PC Card driver at

memory location D8000.

AST Power Exec

DEVICE=C:\DOS\EMM386.EXE NOEMS X=D000-DFFF

DEVICE=C:\CARDSOFT\SS365SL.EXE

DEVICE=C:\CARDOSFT\CS.EXE

DEVICE=C:\CARDSOFT\CSALLOC.EXE

REM DEVICE=C:\CARDSOFT\ATADRV.EXE

REM DEVICE=C:\CARDSOFT\MTSRAM.EXE

REM DEVICE=C:\CARDSOFT\MTDDRV.EXE

DEVICE=C:\CARDSOFT\CARDID.EXE

The above configuration will work with the PRO/100 PC Card driver at

memory location D2000.

Austin Notebooks series

DEVICE=C:\DOS\EMM386.EXE X=D000-D7FF

DEVICE=C:\PCMCIA\CARDSOCK.SYS /IO:240

DEVICE=C:\PCMCIA\CTALKCS.EXE

DEVICE=C:\PCMCIA\CARDTALK.SYS /A /IOW=320-31F /MEMW=D000-D7FF

The above configuration will work with the PRO/100 PC Card driver at

memory location D2000.

Compaq Contura Aero

DEVICE=C:\DOS\EMM386.EXE NOEMS X=D000-D5FF

DEVICE=C:\CPQDOS\SSVLSI.EXE

DEVICE=C:\CPQDOS\CS.EXE

DEVICE=C:\CPQDOS\CSALLOC.EXE C:\CPQDOS\CSALLOC.INI

REM DEVICE=C:\CPQDOS\ATADRV.EXE

DEVICE=C:\CPQDOS\CARDID.EXE C:\CPQDOS\CARDID.INI

REM DEVICE=C:\CPQDOS\MEMDRV.EXE

REM DEVICE=C:\CPQDOS\DBLFLASH.EXE

4-62 PRO/100 LAN+Modem PC Card User’s Guide

REM DEVICE=C:\CPQDOS\MS-FLASH.SYS

The above configuration uses only the drivers necessary for the Intel

adapter. This configuration will work with the PRO/100 PC Card driver at

memory location D2000.

Compaq LTE Elite models

DEVICE=C:\DOS\EMM386.EXE NOEMS X=D000-DFFF

DEVICE=C:\CPQDOS\SSVLSI.EXE

DEVICE=C:\CPQDOS\CS.EXE

DEVICE=C:\CPQDOS\CSALLOC.EXE C:\CPQDOS\CSALLOC.INI

DEVICE=C:\CPQDOS\ATADRV.EXE

DEVICE=C:\CPQDOS\CARDID.EXE C:\CPQDOS\CARDID.INI

DEVICE=C:\CPQDOS\MEMDRV.EXE

DEVICE=C:\CPQDOS\DBLFLASH.EXE

DEVICE=C:\CPQDOS\MS-FLASH.SYS

The above configuration will work with the PRO/100 PC Card driver at

memory location D2000.

Dell Latitude XP series

DEVICE=C:\DOS\EMM386.EXE NOEMS X=D000-DBFF

DEVICE=C:\CARDSOFT\SSVADEM.EXE

DEVICE=C:\CARDOSFT\CS.EXE

DEVICE=C:\CARDSOFT\CSALLOC.EXE

REM DEVICE=C:\CARDSOFT\ATADRV.EXE

REM DEVICE=C:\CARDSOFT\MTSRAM.EXE

REM DEVICE=C:\CARDSOFT\MTDDRV.EXE

DEVICE=C:\CARDSOFT\CARDID.EXE

INSTALL=C:\CARDSOFT\CS_APM.EXE

The above configuration will work with the PRO/100 PC Card driver at

memory location D2000.

Windows 3.x/MS-DOS Installation 4-63

Gateway ColorBook series

DEVICE=C:\DOS\EMM386.EXE NOEMS X=D000-DFFF

DEVICE=C:\CARDSOFT\SSCIRRUS.EXE

DEVICE=C:\CARDOSFT\CS.EXE

DEVICE=C:\CARDSOFT\CSALLOC.EXE

REM DEVICE=C:\CARDSOFT\ATADRV.EXE

REM DEVICE=C:\CARDSOFT\MTSRAM.EXE

REM DEVICE=C:\CARDSOFT\MTDDRV.EXE

DEVICE=C:\CARDSOFT\CARDID.EXE

The above configuration will work with the PRO/100 PC Card driver at

memory location D2000.

IBM ThinkPad 350, 755CS

DEVICE=C:\DOS\EMM386.EXE X=C800-CFFF

The switch X=C800-CFFF on the EMM386 line must be used with the

configuration below.

DEVICE=C:\THINKPAD\IBMDSS01.SYS

DEVICE=C:\THINKPAD\IBMDOSCS.SYS

DEVICE=C:\THINKPAD\DICRMU01.SYS /MA=C800-CFFF

DEVICE=C:\THINKPAD\$ICPMDOS.SYS

REM DEVICE=C:\THINKPAD\AUTODRV.SYS C:\THINKPAD\AUTODRV.INI

The above line has been changed to prevent AUTODRV.SYS from

loading. The above configuration will work with the PRO/100 PC Card

driver at memory location C8000.

IBM ThinkPad 360CS

DEVICE=C:\DOS\EMM386.EXE X=C800-CFFF

The switch X=C800-CFFF on the EMM386 line must be used with the

configuration below.

DEVICE=C:\THINKPAD\IBMDSS01.SYS

DEVICE=C:\THINKPAD\IBMDOSCS.SYS

DEVICE=C:\THINKPAD\DICRMU01.SYS /MA=C800-CFFF

DEVICE=C:\THINKPAD\$ICPMDOS.SYS

DEVICE=C:\THINKPAD\AUTODRV.SYS C:\THINKPAD\AUTODRV.INI

4-64 PRO/100 LAN+Modem PC Card User’s Guide

The above configuration will work with the PRO/100 PC Card driver at

memory location C8000.

IBM ThinkPad 750CS

DEVICE=C:\DOS\EMM386.EXE X=B000-BFFF X=C800-CFFF

The switch X=C800-CFFF on the EMM386 line must be used with the

configuration below.

DEVICE=C:\THINKPAD\IBMDSS01.SYS /S0=2

DEVICE=C:\THINKPAD\IBMDOSCS.SYS

DEVICE=C:\THINKPAD\DICRMU01.SYS /MA=C800-CFFF

DEVICE=C:\THINKPAD\$ICPMDOS.SYS

DEVICE=C:\THINKPAD\AUTODRV.SYS C:\THINKPAD\AUTODRV.INI

REM DEVICE=C:\IBMAUDIO\AUDIODD\TPAUDDD.SYS

The above line must be remarked out if the Thinkpad 750 series has a

built in sound card. The above configuration will work with the PRO/100

PC Card driver at memory location C8000.

NEC Versa models

DEVICE=C:\DOS\EMM386.EXE NOEMS X=D000-DFFF

DEVICE=C:\CARDSOFT\SSCIRRUS.EXE

DEVICE=C:\CARDSOFT\CS.EXE

DEVICE=C:\CARDSOFT\CSALLOC.EXE C:\CARDSOFT\CSALLOC.INI

REM DEVICE=C:\CARDSOFT\ATADRV.EXE

REM DEVICE=C:\CARDSOFT\CARDID.EXE C:\CARDSOFT\CARDID.INI

REM DEVICE=C:\CARDSOFT\MEMDRV.EXE

REM DEVICE=C:\CARDSOFT\DBLFLASH.EXE

REM DEVICE=C:\CARDSOFT\MS-FLASH.SYS

The above configuration will work with the PRO/100 PC Card driver at

memory location D2000.

Sharp 8650

DEVICE=C:\DOS\EMM386.EXE NOEMS X=D000-DFFF

DEVICE=C:\CARDTALK\ARIMASS.SYS

DEVICE=C:\CARDTALK\CTALKCS.EXE

DEVICE=C:\CARDTALK\CARDTALK.SYS /A

Windows 3.x/MS-DOS Installation 4-65

The above configuration will work with the PRO/100 PC Card driver at

memory location D2000.

Toshiba 19xx, 47xx, 48xx series

DEVICE=C:\DOS\EMM386.EXE NOEMS X=C800-CFFF

DEVICE=C:\PCMPLUS3\CNFIGNAM.EXE /DEFAULT

DEVICE=C:\PCMPLUS3\PCMSS.EXE

DEVICE=C:\PCMPLUS3\PCMCS.EXE

DEVICE=C:\PCMPLUS3\PCMRMAN.SYS

DEVICE=C:\PCMPLUS3\PCMSCD.EXE

The above configuration will work with the PRO/100 PC Card driver at

memory location C8000.

4-66 PRO/100 LAN+Modem PC Card User’s Guide

CHAPTER 5

Utilities and Applications

This chapter describes software utilities provided with the PRO/100 PC

Card and provides configuration guidelines for popular communications

applications to be used with the Intel modem.

UTILITIES

Intel provides several utilities with the PRO/100 PC Card that run under

Microsoft Windows or MS-DOS. The utilities are:

• Country Identifier Utility (Windows 95, NT, 3.x)

• Modem Test (Windows 95, NT, 3.x)

• Diagnostic Test (MS-DOS prompt required)

• Modem COM Port Monitor (Windows 3.x only)

The Windows utilities described in this chapter are automatically copied to

your hard drive and launched during installation of the PRO/100 PC Card

under Windows 95 and Windows NT version 4.0, or when you run the

Intel Installation Program under Windows 3.1 or 3.11. Icons for these

utilities are also installed in the Windows program group set up at the time

of installation.

Country Identifier Utility

The Country Identifier utility is a Windows-based utility that enables the

PRO/100 PC Card user to select a “country of installation” setting for

modem communications. This setting enables the modem to function in

accordance with the configuration requirements of a specific country.

5-2 PRO/100 LAN+Modem PC Card User’s Guide

How to Use Country Identifier

The country identifier utility is automatically copied to your hard drive and

launched during installation of the PRO/100 PC Card under Windows 95

and Windows NT version 4.0, or when you run the Intel Installation

Program under Windows 3.1 or 3.11. An icon for Country Identifier is

also installed in the Windows program group so that the utility can be re-

run if the country settings needs to be changed.

Follow the steps below to run Country Identifier from the Intel

program group if you need to modify the country setting chosen

during the installation process.

1 Launch Country Identifier through Windows. Either double-click

the Country Identifier icon in the PRO/100 program group, or use

the Windows File/Run command sequence and type

[path]TELSEL.EXE in the Command Line box, where [path]

indicates the location of the Country Identifier utility on your hard

drive.

2 The current country setting is listed at the top of the screen, and the

other countries supported are listed below. To change to a different

country, locate the country on the list and double click. The

application will verify that the country setting has been changed.

3 Click on Exit to close the program.

Modem Test Utility

The Intel Modem Test utility indicates the status of the COM ports on

your computer, including which COM port the Intel modem is configured

to use. The icon for this program will be installed in the PRO/100

program group at installation. Double-click the icon to run the Modem

Test utility.

If a Intel modem is enabled, the Modem Test utility can also be used as a

terminal program to input AT commands to the modem without the use

of other communications software. Click the Terminal button on the

Modem Test screen to open a window for input of modem commands.

See Chapter 6. Modem Reference for a complete list of modem

commands supported by the PRO/100 PC Card.

Utilities and Applications 5-3

Diagnostic Test Utility (M16BTEST.EXE)

Intel provides a DOS-based self test diagnostics program. This program,

located on PRO/100 PC Card Disk 2, Network Drivers Disk, tests several

adapter functions. It also reports test results, the serial number of the unit,

and the node (or Ethernet) address.

M16BTEST can only be run from an MS-DOS command line. Under

Windows 95 and Windows NT, power down the computer perform a

clean boot to the MS-DOS prompt (under Windows 95 press Shift+F5 at

the message Starting Windows 95 . . . ).

The M16BTEST utility is intended to be a diagnostic tool for trouble-

shooting configuration errors. Cards can be inserted and removed at any

time. Multiple cards and different configurations can be tested.

Executing the Self Test

Use the following steps to execute the self test.

1 Install the PRO/100 PC Card according to the instructions for your

operating system.

2 Power down and restart the computer from MS-DOS (use Shift+F5

in Windows 95). DO NOT load a network driver.

Note

Do not run M16BTEST with a network driver loaded. Loading a

network driver before running M16BTEST may cause unpredict-

able results when exiting the test utility.

3 Run the diagnostic test by typing [path]M16BTEST at the MS-

DOS prompt, then press Enter. [path] can be either

C:\INTEL\M16B\M16BTEST or A:\M16BTEST.

Note

If an error message displays when you execute the self test, see

“Error Messages for Windows 3.x and MS-DOS Drivers” in

Chapter 4. Windows 3.x/MS-DOS Installation.

5-4 PRO/100 LAN+Modem PC Card User’s Guide

Main Screen

The program consists of several function “buttons” and a view pane.

Pressing or invoking a function will bring up the corresponding screen in

the view pane. This view remains until another is selected. To exit

M16BTEST type 'x' or push the 'Exit' button.

When a function is active, the button appears to remain down or pushed.

Once the button pops up, the function is completed and the screen is a

passive results display.

There are nine functions which can be invoked by pushing the associated

button on the main screen. A button can be pushed by pressing the

highlighted letter indicated on the button, or by using the left mouse

button. Each function is explained below.

TEST

This function uses the current configuration to initialize the adapter and

verify it is powered on and properly seated in its slot. It displays the

current setting and test result for each parameter. Parameters are config-

ured through the CONFIGURE function described below. If a card is

detected and initialized successfully, the CIS information is displayed.

A failure may indicate that service is required for the PRO/100 PC Card.

Contact Intel Customer Support.

The CIS section displays the serial number of the unit, its manufacturing

date, and its network node address. This data has been preprogrammed at

the factory and cannot be altered.

CONFIGURE

This function allows the user to set the parameters used for testing. The

address mode can be set to Auto, Memory, or I/O. For Memory and I/O

a hexadecimal address can be specified. The IRQ can be set to Auto, or

IRQ. The IRQ selection can be used to force a particular interrupt. The

network line speed and line mode can also be set from this function.

SOFTWARE

This function attempts to determine what software is currently loaded that

could affect the operation of the card. It displays the current version of

MS-DOS and Windows, and any Card and Socket Services available

(under Windows 3.x or MS-DOS).

Utilities and Applications 5-5

HARDWARE

This function attempts to determine if a PCMCIA controller exists on the

machine. It first checks for PCI BIOS extensions, and then it searches for

any PCMCIA controllers. If found it displays controller type, base I/O

address, offset, number of the socket in which the PRO/100 is installed,

and the PCI interrupt (if enabled by the BIOS).

NETWORK

This function enables the card on the Ethernet network and performs

some diagnostics. It reports the operating mode and speed detected and

monitors the network for traffic. Network traffic is shown on a graph.

This graph provides a visual representation of the volume of traffic on the

local area network (LAN). The Receive Statistics window displays the

cumulative totals for received Packets, KBytes, and Errors.

RESOURCES

This function attempts to determine free resources that are available for

use by the driver. It searches for memory, I/O, and IRQ.

ADVANCED

This function allows the user to set up advanced diagnostics.

ABOUT

This function displays the current version of the diagnostic program.

HELP

This function displays the help screen.

EXIT

This function exits the application.

COM port monitor (Windows 3.x only)

The Intel COM Port Monitor is an onscreen LED program that runs

under Microsoft Windows 3.1 and 3.11, and Windows for Workgroups

3.11. The program provides a simulated onscreen display of modem status

LEDs such as those found on external modems.

5-6 PRO/100 LAN+Modem PC Card User’s Guide

How to Use the COM port monitor

To launch the COM port monitor, double-click on the the COM port

monitor icon in the Intel PRO/100 program group. The COM port

monitor window will be present on the desktop and within applications,

and can be moved by dragging it with the mouse.

COM port monitor is configurable with COM ports 1-4. To configure

with a specific COM port, click once on the COM port monitor window,

and a dialog box will appear. Select a COM port and click OK.

The COM port monitor window contains the following LEDs:

Transmit

Receive

CTS

Clear to Send

Carrier Detect

Ring Indication

To exit the COM port monitor program, Shift+Click on the COM port

monitor window, or click on the window to open the dialog box, then

click on the EXIT button.

Communications Application Notes and

Modem Script Files

Note

The modem script files mentioned in this document are

intended to be used if you have tried a generic Hayes or

Microcom configuration without success. The files referred to in

the application notes are available on disk 2, Network Drivers

Disk, in the \scripts directory.

This section contains instructions for setting up your PRO/100 PC Card

with several popular communications programs.

The following applications are covered in this section:

• America Online v. 3.0

• America Online v. 3.0 with Windows 95

Utilities and Applications 5-7

• CompuServe - WinCIM 2.5.1 with Internet Explorer 2.1

• CompuServe - WinCIM v.3.02 with Windows 95

• Laplink v.6.0

• Laplink v.6.0 with Windows 95

• Lotus CC:Mail Mobile v.2.22 with Windows

• Lotus CC:Mail Mobile v.2.22 with Windows 95

• Lotus Notes v.4.11a with Windows

• Lotus Notes v.4.11a with Windows 95, NT 4.0

• Microsoft Dial-Up Adapter Networking for Windows 95

• Microsoft Remote Access Server (RAS)

• Prodigy Internet v.1.1.6 with Windows 95

Introduction

Some of the instructions include references to modem script files. The

following files are contained in the \scripts directory on disk 2:

• CLASS73.MDM

• MODEM.INI

• M16BRAS1.INF

• M16BMSM.SCR

• M16BMSM.MDM

• M16BLOT.MDM

Modem Setup with a Communications Program

Most communications programs include a modem setup function or will

autodetect the modem using a sequence of steps like the following:

1 Search for modem

2 Determine manufacturer, model, speed, communications port, and

interrupt

3 Incorporate modem configuration into program

If the Intel modem is installed before the communications program is,

the Intel modem will be automatically configured by the communications

program.

5-8 PRO/100 LAN+Modem PC Card User’s Guide

If the communications program is already installed, you are installing a

new modem, or your modem is not functioning, follow the instructions

for your application.

Modem Setup After Windows 95 Installation

1 Install the PRO/100 PC Card according to the instructions in

Chapter 2. Windows 95 Installation.

2 Verify modem settings as follows:

a Go to Control Panel.

b Double-click the Modem icon.

c Highlight the EtherExpress PRO/100 LAN+Modem PC Card.

d Click Properties.

e Note the Communications Port assigned to the Intel adapter

under the General tab.

Accept the default or set the Maximum Speed of the modem.

g Use the default initialization string or modify it by clicking the

Connection Tab, then Advanced, and inputting changes on the

Extra Settings line.

3 Verify that the modem is functioning via Modem Diagnostics and

Hyperterminal.

4 Install the communications program. The Intel modem is automati-

cally configured by the communications program, if the modem is

installed prior to the communications program. During the installa-

tion process, you will be prompted to verify the Modem selection,

communications port, etc.

America Online version 3.0

America Online v.3.0 ships with a MODEM.INI file. This file must be

modified in order to use the EtherExpress PRO/100 LAN+Modem PC

Card.

1 To update the MODEM.INI file, do the following:

Utilities and Applications 5-9

a In the C:\AOL30\MPM sub-directory,

b Rename the CLASS73.MDM file to CLASS73.OLD and

MODEM.INI file to MODEM.OLD.

c Copy the new CLASS73.MDM and MODEM.INI files to the

C:\AOL30\MPM sub-directory.

d Start the America Online program.

2 To set up the PRO/100 PC Card, click SETUP on the Welcome

screen.

a Click Modem Setup in the Network & Modem Setup window.

b In the Modem Selection and Customization window.

• Select the COM port that is assigned to the Intel PRO/100

modem under Modem Port.

• Highlight "EtherExpress PRO/100 LAN+Modem PC Card,"

then click OK.

• Note: Use the default initialization string. If you need to change

the string, you may do so under the Edit Commands options.

America Online version 3.0 with Windows 95

America Online v.3.0 ships with a MODEM.INI file. This file must be

modified in order to use the EtherExpress PRO/100 LAN+Modem PC

Card.

1 To update the MODEM.INI file, proceed as follows:

a In the C:\AOL30\MPM sub-directory,

b Rename the CLASS73.MDM file to CLASS73.OLD and

MODEM.INI file to MODEM.OLD.

c Copy the new CLASS73.MDM and MODEM.INI files to the

C:\AOL30\MPM sub-directory.

d Start the America Online program.

2 To set up your Intel product, click SETUP on the Welcome screen.

5-10 PRO/100 LAN+Modem PC Card User’s Guide

a Click Modem Setup in the Network & Modem Setup window.

b In the Modem Selection and Customization window.

• Select the COM # that is assigned to the Intel modem under

Modem Port.

• Highlight "EtherExpress PRO/100 LAN+Modem PC Card,"

then click OK.

• Note: Use the default initialization string. If you need to change

the string, you may do so under the Edit Commands options.

CompuServe WINCIM version 2.5.1 with Internet Ex-

plorer version 2.1

To set up the Intel modem or modify the present configuration:

1 Click Special.

2 Click Session Settings.

a Indicate which COM port is assigned to the Intel modem under

Connector.

b Select the speed of the Intel modem under Baud Rate.

c Click once in the box to the left of Use Winsock, for Internet

access.

3 Click Modem in the Setup Session Settings window.

a In the Modem Current Settings window, select "Other" under

Modem.

b Use the default initialization string. If modification is required,

enter the necessary changes in the Initialize: section.

c Click OK, to update configuration and close menus.

CompuServe WINCIM version 3.02 with Windows 95

To set up the Intel modem or modify the present configuration:

1 Click Access or the Setup icon.

Utilities and Applications 5-11

2 Click Preferences.

3 In the Connection window under Connection Type check all

settings for accuracy.

a Winsock: (Default WINSOCK).

b Connect using:

c Phone #:

d Port:

e Port speed:

Dial type:

Modify any of the above settings are not valid.

4 To modify the modem type, click Define Modem, highlight Intel as

manufacturer and the EtherExpress PRO/100 LAN+Modem PC

Card model.

Note

The default initialization string should suffice. To modify your

initialization string, click Define Modem and enter the new

initialization string in the Initialization section.

5 Click OK to save configuration and exit.

LapLink version 6.0

To set up the Intel modem or modify the present configuration:

1 In the Control Panel, click the Modem icon to access the Port Setup

window.

2 In the Port Setup Screen.

a Click the communications port that corresponds to the one

assigned to the modem.

b Select Modem under Type.

5-12 PRO/100 LAN+Modem PC Card User’s Guide

c Enable Port by clicking box in that field.

3 Click Configure to configure the modem.

a Select your modem Speed under Modem Settings.

b Under Modem Type, select Hayes Generic.

c To modify the modem initialization string, which is usually not

necessary, click Customize and make any changes required. Click

OK, then Close.

d Enter the phone number(s) of your service provider and/or BBS

in the Connect over Modem window under Phone Number. Be

sure entries in Services and Security are correct for your envi-

ronment and/or the type of action you wish to exercise.

If too many programs are loaded via the LOAD or RUN statements in

your c:\windows\win.ini file, you will receive an “Out of System Memory

Error” when running LapLink. Correct this error by temporarily editing

out any special programs in those two statements. Make a backup copy of

the WIN.INI file before editing it. The load=c:\(Laplink

Directory)\llwload.exe line must reside in the WIN.INI, as it is required

for LapLink to work.

Operating inconsistencies will be experienced when Card and Socket

Services are used with LapLink. If you need to use LapLink, it is recom-

mended that Card and Socket Services not be used.

LapLink version 6.0 with Windows 95

To set up the Intel PRO/100 modem or modify the present configuration:

the steps are the same as those listed above for LapLink 6.0, except under

3.d.

1 In the Connect over Modem window under Dialing enter:

a The phone number(s) of your service provider and/or BBS

Phone Number.

b The location that you are dialing from under Dialing Location.

c Notice that in Connect Over Modem, Connect Using, the

Utilities and Applications 5-13

EtherExpress PRO/100 LAN+Modem PC Card.

d Verify that the entry in Services section matches the action you

wish to exercise.

e There is no Security category.

Lotus cc:Mail Mobile version 2.22 with Windows 3.1

1 Copy the M16BLOT.MDM file to the default directory where the

Lotus cc:Mobile *.MDM files are located.

2 Setup Lotus cc:Mobile to use this M16BLOT.MDM file as follows:

a From the Lotus cc:Mail Mobile Main Menu, select Mobile.

b Next, select Location Setup.

c In Telephone, verify that your Dialing Rules and Strings are

correct.

d In Communications, highlight Default Communications Method,

then set.

• Connection Type = Modem.

• Modem Type = EtherExpress PRO/100 LAN+Modem PC Card

(select the correct modem).

• Serial Port = Communication Port assigned to the modem.

3 Click OK to save and close.

4 Enable SESSION.LOG to obtain the status of the modem:.

a From the Lotus cc:Mail Mobile Main Menu, select Mobile,

Mobile Setup:.

b Place a ‘check mark’ under Save cc:Mail Background Session

Log.

c Place a ‘check mark’ under Activate Diagnostics in cc:Mail

Background.

5-14 PRO/100 LAN+Modem PC Card User’s Guide

Lotus cc:Mail Mobile version 2.22 with Windows 95

1 Copy the M16BLOT.MDM file to the default directory where the

Lotus cc:Mobile *.MDM files are stored.

2 Setup Lotus cc:Mobile to use this M16BLOT.MDM file as follows:

a From the Lotus cc:Mail Mobile Main Menu, select Mobile,.

b Next select Location Setup.

c In Telephone, verify that the Dialing Rules and Strings are

correct.

d In Communications, highlight Default Communications

Method,then Edit as follows:

• Connection Type = Modem.

• Modem Type = EtherExpress PRO/100 LAN+Modem PC

Card.

• Serial Port = Com Port setting used in Windows 95.

3 Click OK to save and close.

4 Enable SESSION.LOG to obtain the modem status of:

a From the Lotus cc:Mail Mobile Main Menu, select Mobile,

Mobile Setup:

b Place a ‘check mark’ under Save cc:Mail Background Session

Log.

c Place a ‘check mark’ under Activate Diagnostics in cc:Mail

Background.

Lotus Notes version 4.11A with Windows

To set up the Intel PRO/100 modem or modify the present configuration:

1 Copy the M16BLOT.MDM file to the default directory where the

Lotus Notes program is installed. \NOTES\DATA\MODEMS.

2 In the Lotus Notes Desktop screen, click File.

3 Click Tools.

Utilities and Applications 5-15

4 Click User Preferences.

5 Click the Ports icon.

6 Under Communications Ports.

a Select the appropriate protocol if connecting via the network.

b If connecting over the modem .

• Select the correct COM port.

• Click in the Port Enabled box.

7 If connecting over modem, click COM# Options,.

a Under Modem type, verify EtherExpress PRO/100

LAN+Modem PC Card is listed.

b Verify that the Maximum port speed is set to 115.2Kbps.

c Use the default initialization string. .

d Click OK to save changes and exit.

Lotus Notes version 4.11A with Windows 95 and NT

4.0

To set up the Intel modem or modify the present configuration:

1 Copy the M16BLOT.MDM file to the default directory where Lotus

Notes program is installed. \NOTES\DATA\MODEMS

2 In the Lotus Notes Desktop screen, click File.

3 Click Tools.

4 Click User Preferences....

5 Click the Ports icon.

6 Under Communications Ports.

5-16 PRO/100 LAN+Modem PC Card User’s Guide

a Select the appropriate protocol if connecting via the network

b If connecting over the modem .

• Select the correct COM#.

• Click in the Port Enabled box.

7 If connecting over modem, click COM# Options,.

a Under Modem type, verify that EtherExpress PRO/100

LAN+Modem PC Card is listed.

b Verify that the Maximum port speed is set to 115.2 Kbps.

c Use the default initialization string. If you need to modify.the

string, do so under ControlPanel\Modems\Modem

Properties\Connection\Advanced\Extra Settings.

Click OK to save changes and exit.

Microsoft Dial-Up Adapter Network Setup for Windows

The Microsoft Dial-Up Adapter may be used for Remote Access Service

(RAS), remote connection to in-house server and/or to access the

Internet. To install the Dial-Up Adapter,

1 In the Control Panel, double-click the Network icon.

2 Click Add.

3 Double-click Adapter.

4 Highlight Microsoft under Manufacturers. Dial-Up Adapter will

appear under Network Adapters, click OK.

5 Windows 95 disks may be requested if not present in

C:\Windows\Options\Cabs sub-directory

6 Add the proper networking protocol for the Dial-Up Adapter (i.e.

TCP/IP, (IP, Subnet Mask, and Gateway may be required)).

7 Restart the computer when prompted.

Utilities and Applications 5-17

8 Modify the Dial-Up Adapter properties.

a Double-click the My Computer icon on the desktop.

b Double-click the Dial-Up Networking icon.

c Double-click the Make New Connection icon.

• Type in the Name of the computer or service you want to dial

• Under Select a Modem, select the Intel modem that is installed

• Click Configure, confirm COM Port and Maximum Speed

• Use the default Initialization String. To modify the string click

the Connection tab, and then Advanced Connection Settings.

Enter all changes under Extra Settings:

• Click OK to return to the Make New Connection screen, then

click Next

• Enter the Area Code and Telephone number of computer or

service, click Next, then Finish

Microsoft Remote Access Server (RAS)

1 Enable network functionality in Windows for Workgroups

a Double-click the Network Setup icon

b Click Networks

c Click Install Windows Network, then OK

d Click Drivers

e Click Add Adapter

By default Unlisted or Updated Network Adapter is highlighted,

if not, select it then click OK. When prompted, insert the latest

version of the Intel Network Driver disk in drive A:\, then click

OK.

5-18 PRO/100 LAN+Modem PC Card User’s Guide

g Select M16BNDIS.EXE Real Mode (for all Intel adapters), then

click OK

h Remove the IPX/SPX Compatible Transport with NetBIOS

driver only, click Close, then OK

In the Windows Setup screen click Yes to All, “...to replace all

later files with the version you are installing now...” Windows

disks #7 and 8 are required to complete the installation

Confirm that the Local Network is functional and that you can

access the modem using the TERMINAL program in Accesso-

ries Group before proceeding to the next step.

2 Copy the M16BRAS1.INF file from the \scripts directory on disk 2

to the c:\windows\system directory.

3 Exit Windows and go to the C:\Windows\System sub-directory.

Back up the original MODEM.INF with the following command:

COPY MODEM.INF MODEM.BAK

4 Append the Intel M16BRAS1.INF file to the end of the

MODEM.INF file. To do this, issue the following commands:

COPY MODEM.INF+M16BRAS1.INF MODEM.NEW

COPY MODEM.NEW MODEM.INF

5 Modify the new MODEM.INF in the [Intel EtherExpress PRO/

100 Lan+Modem PC Card] section, edit the following lines:

MAXCARRIERBPS= 56000

MAXCONNECTBPS= 56000

6 Save the file and exit the editor

7 Double-click the Windows Network Setup icon

8 Install Remote Access Service in Windows for Workgroups

a Double-click the Network Setup icon, then the RASSTART icon

b Click Install to continue

c In the Remote Access screen click Yes to All, “...to replace all

later files with the version you are installing now, press Yes to

Utilities and Applications 5-19

All.” Windows disks #7 and 8 are required to complete the

installation

d In the Remote Access Configuration screen,

• Click the COM port assigned to the Intel modem

• Under Device, select Intel EtherExpress PRO/100.

• Click OK to save changes, then Click Restart Computer

9 Restart RAST to input the phone number(s) into RAS

a Click Edit to access the Edit Phone Book Entry screen.

b Input all other required data

c Under Port: select Any modem port,

d Click OK to save and exit

Prodigy Internet version 1.1.6 with Windows 95

To set up the Intel modem or modify the present configuration:

Double-click NetAssist for Prodigy Internet.

Click Dialer Settings.

Click Modem Info. Highlight the EtherExpress PRO/100

LAN+Modem.

By default, there should be an ‘X’ in the ‘Check this if you have a

PCMCIA modem’.

Click Change Modem Strings.

Modify the Init String: line to read AT&FE0Q0V0, then click OK.

Click OK to exit the Modem Settings menu.

Click Exit to accept changes and close the NetAssist Windows

Application - NetAssist.

Double-click the Prodigy Internet icon to access the service.

5-20 PRO/100 LAN+Modem PC Card User’s Guide

CHAPTER 6

Modem Reference

This chapter contains a comprehensive modem reference guide, including

result codes and all AT commands and S-Registers supported by the

PRO/100 LAN+Modem PC Card.

Result Codes

Long

Short

Description

Command successfully executed

Connect

CONNECT

RING

Incoming ring signal detected

Carrier detect failed/carrier dropped

Command is invalid

NO CARRIER

ERROR

CONNECT 1200

NO DIALTONE

BUSY

Connection established at 1200bps

No tone during interval set with S6

Busy signal detected

NO ANSWER

CONNECT 2400

CONNECT 4800

CONNECT 9600

CONNECT 14400

CONNECT 19200

CONNECT 57600

Remote end never answered

10 Connection established at 2400bps

11 Connection established at 4800bps

12 Connection established at 9600bps

13 Connection established at 14400bps

14 Connection established at 19200bps

18 Connection established at 57600bps

CONNECT 1200/75 22 Connection at 1200 (Tx)/75 (Rx) bps

6-2 PRO/100 LAN+Modem PC Card User’s Guide

Long Short Description

CONNECT 75/1200 23 Connection at 75 (Tx)/1200 (Rx) bps

CONNECT 7200

CONNECT 12000

CONNECT 38400

CONNECT 300

24 Connection established at 7200bps

25 Connection established at 12000bps

28 Connection established at 38400bps

40 Connection established at 300bps

55 Connection established at 21600bps

56 Connection established at 24000bps

57 Connection established at 26400bps

58 Connection established at 28800bps

59 Connection established at 31200bps

60 Connection established at 33600bps

70 Connection established at 32000bps

71 Connection established at 34000bps

72 Connection established at 36000bps

73 Connection established at 38000bps

74 Connection established at 40000bps

75 Connection established at 42000bps

76 Connection established at 44000bps

77 Connection established at 46000bps

78 Connection established at 48000bps

79 Connection established at 50000bps

80 Connection established at 52000bps

81 Connection established at 54000bps

82 Connection established at 56000bps

86 Connection established at 16800bps

87 Connection at 115200bps

CONNECT 21600

CONNECT 24000

CONNECT 26400

CONNECT 28800

CONNECT 31200

CONNECT 33600

CONNECT 32000

CONNECT 34000

CONNECT 36000

CONNECT 38000

CONNECT 40000

CONNECT 42000

CONNECT 44000

CONNECT 46000

CONNECT 48000

CONNECT 50000

CONNECT 52000

CONNECT 54000

CONNECT 56000

CONNECT 16800

CONNECT 115200

DELAYED

88 Delay in effect for dialed number

89 Dialed number is blacklisted

BLACKLISTED

BLACKLIST FULL

+FCERROR

90 Blacklist is full

+F4Fax command error

Modem Reference 6-3

Long

Short Description

CARRIER 75/1200

CARRIER 1200

CARRIER 1200/75

CARRIER 2400

CARRIER 4800

CARRIER 7200

CARRIER 9600

CARRIER 12000

CARRIER 14400

CARRIER 16800

CARRIER 19200

CARRIER 21600

CARRIER 24000

CARRIER 26400

CARRIER 28800

CARRIER 31200

CARRIER 33600

Carrier detected 75 (Tx)/1200 (Rx) bps

Carrier detected at 1200bps

Carrier detected 1200 (Tx)/75 (Rx) bps

Carrier detected at 2400bps

Carrier detected at 4800bps

Carrier detected at 7200bps

Carrier detected at 9600bps

Carrier detected at 12000bps

Carrier detected at 14400bps

Carrier detected at 16800bps

Carrier detected at 19200bps

Carrier detected at 21600bps

Carrier detected at 24000bps

Carrier detected at 26400bps

Carrier detected at 28800bps

Carrier detected at 31200bps

Carrier detected at 33600bps

COMPRESSION: MNP5

COMPRESSON: V.42BIS

COMPRESSION: NONE

MNP/5 compression enabled

V.42bis compression enabled

Data compression disabled

PROTOCOL: NONE

PROTOCOL: LAP-M

PROTOCOL: MNP

Standard asynchronous mode

V.42 error control mode: LAP-M

Alternate EC protocol: MNP

_____________________

*These result codes do not have numeric (short) equivalents.

6-4 PRO/100 LAN+Modem PC Card User’s Guide

AT Command Reference

With the exception of the “Special Commands” described at the beginning

of the Command Reference, all commands must be preceded by the AT

attention code (or command prefix) and terminated by pressing the Enter

key.

The modem responds with the result code OK, which means it under-

stands and can execute the command, or with ERROR, which means that

the modem does not understand the command or that the command is

invalid. For a complete list of result codes, see the beginning of this

chapter.

The modem must be in command mode when any command other than

the online escape sequence is entered. Commands entered when the

modem is in online mode are treated as data and transmitted as such to

the modem at the other end of the line.

Special Commands

+++ Online Escape Sequence

The escape sequence is used to switch to command mode from online

mode during a session with a remote modem. Type three “plus signs.” The

escape sequence is not preceded by the AT command prefix, nor does it

require the Enter key. The setting of S-Register S2 determines the ASCII

character used. S2=43 is the default (the “+” sign). 0-127 are valid. To

disable the command, set S2 to a value greater than 127. Use the ATO

(“AT” and letter “oh”) command to return to online mode.

Insert a pause before and after the escape sequence to prevent misinter-

pretation of the escape sequence as data. Use S-Register S12 to set the

length of the pause.

Repeat Last Command

The A/ command causes the modem to repeat the last command string.

The command executes as soon as / is typed. It does not require the AT

command line prefix, nor does it need to be followed by Enter.

Modem Reference 6-5

AT Command Reference

Answer

Typing ATA causes the modem to go off-hook and respond to an

incoming call by generating a carrier signal and starting the handshaking

process. This must be the only command or the final command in the

command line.

If the handshaking process is successful and a connection is established,

the normal CONNECT message is displayed. If the carrier signal is not

detected within the time specified in S-Register S7, a NO CARRIER result

code is displayed.

Bn Select Communications Standard

The ATBn command selects the communication standard (ITU or Bell)

to be used by the modem, as follows:

Use ITU V.22 at 1200bps. B0 selects ITU V.22 at

1200bps and ITU V.21 at 300bps.

Use Bell 212A at 1200bps. B1 selects Bell 212A at

1200bps and Bell 103J at 300bps.

Unselect V.23 reverse channel.

Select V.23 reverse channel.

B15

Selects V.21 when the modem is at 300bps (same as

B0).

B16

Selects Bell103J when the modem is at 300bps (same as

B1).

Note

The ATB1 and ATB16 parameter settings are not available in

some countries. Defaults are country-specific.

Break (Escape) command

See “Special Commands” at the beginning of this Command Reference

section.

6-6 PRO/100 LAN+Modem PC Card User’s Guide

Cn Carrier Control

The ATCn command, where n is 1, guarantees backward compatibility

with communications software that issues the C1 command. C0 is not

supported; it may set some modems to "receive only mode."

Transmit carrier always off (not supported).

Normal transmit carrier switching.

Dn Dial A Telephone Number

The ATDn command is used to dial a telephone number. The n repre-

sents a dial string consisting of dial digits/characters and dial modifiers

(see below) and must not exceed 40 characters. Spaces, hyphens, and

parentheses can be used for clarity, but they are ignored by the modem.

The Dial command can be used for either pulse (rotary) or tone dialing.

The dial digits/characters are 0 - 9 A B C D # *. The characters A B C D

and the symbols # and * represent specific tone pairs and can be used

only when tone dialing. These characters and symbols are ignored when

pulse dialing is used. Some countries restrict or prohibit the use of some

of these characters.

Dial Modifiers

Dial modifiers are recognized by the modem only when they are part of a

dial string following the ATD command. Possible dial modifiers are:

Redial Last Number

Redials last number if used as first character following ATD. Other-

wise it is ignored.

Pulse Dialing Method

The P modifier is used with the Dial command to instruct the

modem to pulse dial the telephone number that follows.

Modem Reference 6-7

Dial Modifiers (continued)

S=n Dial a Stored Telephone Number

The S modifier instructs the modem to dial a number that had been

previously stored by the use of the AT&Zn=x command. The

command to dial a stored telephone number is ATDS=n, where n

represents telephone number storage location 0 or 1. For example,

ATD P S=1 pulse dials the telephone number written to telephone

number storage location 1.

Delay Processing the Next Character

When the comma (,) modifier is included as part of the dial string

following the ATD command, the modem pauses before processing

the next character in the dial string. The duration of the pause is

dictated by the contents of S-Register S8.

The , modifier is frequently inserted after the digit (usually 9) used to

obtain an outside line from a PBX to allow sufficient time for the dial

tone to occur before the modem dials the telephone number. The W

modifier can be used in place of the comma.

Some countries place restrictions on the amount of time a modem

may delay during dialing.

Tone Dialing Method

The T modifier is used with the Dial command to instruct the

modem to tone dial the telephone number that follows. See also the

ATT command.

Wait for Second Dial Tone

The W modifier instructs the modem to wait for a dial tone before

processing the remaining characters in the dial string.

Hook Flash

The ! modifier serves as a switch hook (or hook flash) signal. This

causes the modem to hang up (go on-hook) for about 0.5 seconds

then return to off-hook (the actual duration of the hook flash varies

in different countries).

6-8 PRO/100 LAN+Modem PC Card User’s Guide

Dial Modifiers (continued)

Wait for Quiet Answer

The @ modifier in a dial string instructs the modem to wait for five

seconds of silence after dialing the number. If silence is not detected,

the modem sends a NO ANSWER result code to the user.

;

Return to Command Mode after Dialing

The semicolon (;) dial modifier can be used only at the end of a

command line, immediately preceding the Enter, and instructs the

modem to return to the command mode immediately after dialing and

without breaking the connection with the distant modem.

Disable Data Calling Tone Transmission

The ^ modifier in a dial string disables data calling tone for the

current call (calling tone is automatically enabled in many countries).

This modifier is not available in all countries.

Credit Card Tone Detect

The $ modifier in a dial string instructs the modem to wait for a

credit card “bong” tone before processing the remaining characters in

the dial string.

En Echo Command

The ATEn command, where n represents 0 or 1, determines if the

commands you issue through the keyboard to the modem in command

mode are displayed (echoed) on your computer’s monitor screen.

Disable echo to the computer

Enable echo to the computer (default)

If the commands you type are not displayed on your monitor screen, your

software is set to expect character echo from the remote system. You can

remedy this by typing in the command ATE1. If the commands you type

are displayed on your monitor with the characters duplicated,

LLIIKKEETTHHIISS, type in the ATE0 command.

Modem Reference 6-9

Fn Online Data Character Echo command

Ths ATFn command determines whether the modem will echo data from

the DTE. This modem does not support the F0 version of the command.

To ensure backward compatibility, the modem will accept F1.

Online data character echo enabled (not supported;

returns ERROR)

Online data character echo disabled

Hn Switch Hook Options

The ATHn command hangs up the modem or prepares it for dialing.

ATH0

Causes the modem to go on-hook (default).

ATH1

Causes the modem to go off-hook (this command is

restricted in some countries).

Request ID Information

The ATI command has various options which are used to instruct the

modem to provide specific information about itself.

Displays modem controller firmware revision (same as

I3)

Calculates ROM checksum and displays it on the DTE

(for example, 12AB)

Performs a ROM check and calculates and verifies the

checksum. displaying OK or ERROR.

Displays modem firmware revision information

Returns country code (for example, North America)

I12

6-10 PRO/100 LAN+Modem PC Card User’s Guide

Ln Monitor Speaker Volume

The ATLn command, where n represents 0, 1, 2, or 3, is listed here for

backward compatibility reference only. The volume of the monitor

speaker is controlled by the laptop computer, not by the modem.

Mn Speaker On/Off Selection

The ATMn command, where n represents 0, 1, 2, or 3, enables or disables

the transmission of sound signals from the modem to the computer

speaker. (Sound production also requires that the computer speaker be

enabled.)

Speaker always off.

Speaker on until data carrier is detected

Speaker always on when modem is off-hook

Speaker off as digits are dialed, then on after dialing

until data carrier is detected

Nn Negotiation of Handshaking Options

The ATNn command, where n represents 0 or 1, determines whether or

not the sending modem performs a negotiated handshake when the speed

of the answering modem is different from that of the sending modem.

When originating or answering, handshake only at the

communication standard specified by the contents of S-

When originating or answering, handshake only at the

communication standard specified by the contents of S-

During handshaking, fall back to a lower speed, if

required. (default)

On Online Command

If the modem has been switched to command mode, typing in the ATO0

command will return it to the online mode with the existing connection.

Modem Reference 6-11

Instructs modem to leave online command mode and

return to data mode (see +++ Escape Sequence under

“Special Commands”)

This setting issues a retrain command before returning

to online data mode.

This setting issues a rate negotiation command before

returning to online data mode.

Select Pulse Dialing

The ATP command instructs the modem to use pulse (rotary) dialing.

This mode will remain in force for all dialing procedures unless an ATT

command is issued or the dial string contains a T dial modifier.

Qn Result Code Display Options

The setting of the ATQn command, where n represents 0 or 1, deter-

mines whether or not result codes (such as OK, CONNECT, RING, NO

CARRIER, and ERROR) are displayed on your PC’s screen.

Display of result codes enabled.

Display of result codes disabled.

Repeat command

See “Special Commands” at the beginning of this chapter.

Select Tone Dialing

The ATT command instructs the modem to use tone dialing. This mode

will remain in force for all dialing procedures unless an ATP command is

issued or the dial string contains a P dial modifier. Tone dialing is the

factory-default setting.

Vn Result Code Format Options

The ATVn command, where n represents 0 or 1, determines if result

codes are displayed as numeric (short form) codes or words (long form).

Numeric result codes contain only one or two digits and this form could

be used, for example, when the modem is controlled by a software

terminal emulation program that uses script files. See the list at the

6-12 PRO/100 LAN+Modem PC Card User’s Guide

beginning of this chapter showing result codes in both long and short

formats..

Type the command ATV or ATV0 to select numeric result codes. The

factory default is to display the result codes as words (ATV1). You should

issue an ATV1 command either to reset the factory default after a change

has been made or to select the long-form (word) result codes. Negotiation

progress messages (extended result codes) are those with a numerical value

of 40 or more.

Four other AT commands, two dial modifiers, and an S-Register are also

directly involved in the generation and display of result codes. These are

the ATQn, ATVn, ATWn, and ATXn commands, the ATDW and

ATD@ dial modifiers, and S-Register S95.

Wn Negotiation Progress Message Selection

The ATWn command, where n represents 0, 1, or 2, works in conjunction

with S-Register S95 to determine how that subset of the result codes —

called negotiation progress messages or extended result codes — will be

used to report the type of connection, protocol, and other communication

techniques that resulted from handshaking and subsequent negotiation.

The options available to represent n in the ATWn command are:

CONNECT result code reports DTE speed. If S-

result codes.

CONNECT result code reports DTE speed. If S-

PROTOCOL extended result codes only.

CONNECT result code reports DCE (modem-to-

modem) speed. If S-Register S95=0, disable the display

of all extended result codes.

Xn Result Code Set/Call Progress Option

The ATXn command, where n represents 0-4, controls how the modem

responds to dial tone and busy signals and how it displays CONNECT

result codes. The options available to specify with the ATXn command

are:

Modem Reference 6-13

Result codes 0-4 enabled. Busy detect and dial tone

detect disabled.

Result codes 0-5, and 10 enabled. Busy detect and dial

tone detect disabled.

Result codes 0-6, and 10 enabled. Busy detect disabled

and dial tone detect enabled.

Result codes 0-5, 7, and 10 enabled. Busy detect

enabled and dial tone detect disabled.

Result codes 0-7, and 10 enabled. Busy detect and dial

tone detect enabled.

Note

Some countries do not allow busy detect or dial tone detect to be

disabled.

Yn Long Space Disconnect Option

The ATYn command, where n represents 0 or 1, determines whether or

not the modem will disconnect a call when it receives a long space (1.6

seconds Break) signal during a V.22bis connection.

Disables the long space disconnect facility (supported

for backward compatibility reference only).

Enables the long space disconnect facility (not supported).

Zn Recall Stored Profile

The ATZn command, where n represents 0, disconnects any call that is

currently in progress and reloads the user configuration profile stored in

nonvolatile memory as the active configuration profile.

Disconnect and reload the profile contained in storage

location 0 as the active configuration profile.

&Bn V.32 Automatic Retrain Options

The EtherExpress PRO/100 LAN/Modem PC Card always retrains. The

automatic retrain feature cannot be disabled.

6-14 PRO/100 LAN+Modem PC Card User’s Guide

&B0

Disables the V.32 automatic retrain capability (not

supported).

&B1

Enables the V.32 automatic retrain capability (sup-

ported for backward compatibility only).

&Cn Data Carrier Detect (DCD)

The AT&Cn command, where n represents 0 or 1, selects the method by

which the modem handles the carrier detect signal.

&C0

The carrier detect signal is forced on regardless of the

condition of the distant modem’s carrier.

&C1

The state of the carrier from the remote modem is

monitored. The local modem’s DCD signal is on when

the remote modem’s carrier signal is detected, and off

when it is not (default).

&Dn Data Terminal Ready (DTR) Options

The AT&Dn command, where n represents 0-3, controls how the Data

Terminal Ready (DTR) signal is used by the modem.

&D0

Ignore the DTR signal from the computer and treat it

as always on.

&D1

Monitor DTR and, when an ON-to-OFF transition of

the DTR signal occurs, switch to command mode, issue

an OK result code, and remain connected.

&D2

Monitor DTR and, when an ON-to-OFF transition of

the DTR signal occurs, hang up the line and switch to

command mode.

&D3

Monitor DTR and, when an ON-to-OFF transition of

the DTR signal occurs, hang up, reset the modem and

switch to the initialization state.

Modem Reference 6-15

&Fn Load Factory Settings

The AT&F command loads factory default parameters from ROM into

the active configuration profile, replacing the parameters stored there.

This command must be issued by itself. If it is used with another AT

command, its function will be ignored.

&F0

&F5

Recall factory settings as active configuration

Recall factory settings appropriate for ETC mode as

active configuration. This command enables ETC

operation. It is automatically set upon detection of a

cellular phone. The following options are set with &F5:

Local Factory Settings

Function

MTC Implementation

LAPM-only error correction

\N4

Transmit level fixed per cellular phone S92

Wait for carrier = 90 sec

CD loss delay = 10 sec

Auto FF/FB enabled

Start up at 9600bps

S7=90

S10=100

N/A

S40=2

&Gn V.22bis Guard Tone Selection

This option is for international use only. It is not used in North America.

The AT&Gn determines which guard tone, if any, to transmit while in

answer mode (transmitting in the high band). The value of n can be 0, 1,

or 2. This parameter is set automatically for most countries that require it.

&G0

&G1

&G2

No guard tone set

550-Hz guard tone set

1800-Hz guard tone set

&Jn Auxiliary Relay Option

&J0

&J1

Auxiliary relay is never closed

Not supported (returns ERROR)

6-16 PRO/100 LAN+Modem PC Card User’s Guide

&Kn Local Flow Control Options

The AT&Kn command, where n represents 0-4, determines how the flow

control between the computer and the local modem is handled.

&K0

&K1

&K2

&K3

&K4

Disable local flow control.

Reserved.

Enable RTS/CTS flow control (default).

Enable XON/XOFF flow control.

&Mn Asynchronous Communications Mode

The AT&Mn command, where n represents 0-4, determines how the

flow control between the computer and the local modem is handled.

&M0

Asynchronous mode (default; supplied for backward

compatibility only).

&M1

&M2

&M3

&M4

Reserved.

&Pn Pulse Dial Make-to-Break Ratio Selec-

tion (Japan only)

The AT&Pn command, where n represents 0 or 1, controls the ratio of

the off-hook (make) to on-hook (break) interval used by the modem when

it pulse dials.

&P0

&P1

&P2

Selects 39:61 make/break ratio at 10 pps (default)

Selects 33:67 make/break ratio at 10 pps

Selects 33:67 make/break ratio at 20 pps

Modem Reference 6-17

&Qn Asynchronous Communications Mode

&Q0

&Q1

&Q2

&Q3

&Q4

&Q5

&Q6

&Q7

Asynchronous mode, buffered (same as \N0)

Reserved

Error control mode, buffered (default; same as \N3)

Asynchronous mode, buffered (same as \N0)

Reserved

&Sn Data Set Ready (DSR) Options

The AT&Sn command controls the functions of the modem’s DSR

circuits.

&S0

The DSR signal remains on all the time the modem is

powered on (default)

&S1

The DSR signal is on during handshaking and is off

when carrier is lost.

&Tn Self-Test Commands

The AT&Tn command allows the user to perform diagnostic tests on the

modem.

&T0

Abort. Stops any test in progress.

&T1

Local analog loop. this test verifies modem operation,

as well as the connection between the modem and

computer. The modem must be off-line when this test

is run.

&T3

&T6

Local digital loopback test.

Remote digital loopback test. This test can verify the

integrity of the local modem, the communications link,

and the remote modem. The modems must be online

with error control disabled when this test is run.

6-18 PRO/100 LAN+Modem PC Card User’s Guide

&V View Configuration Profile

The AT&V command displays the contents of the active configuration

profile.

&Wn Write Active Profile to Memory

The AT&Wn command, where n is 0, allows you to save a copy of the

current active configuration profile to nonvolatile memory. This profile

can be restored at any time by using the ATZ command or a power-up

reset of the modem.

&Yn Select Stored Profile for Hard Reset

This command is included for compatibility with applications that use the

&Y0 command. It does not affect the behavior of the modem.

&Y0

Select stored profile 0 on power up

ERROR

&Y1

&Zn=x

Store Telephone Number

The AT&Zn=x command is used to store a telephone number for later

dialing using the ATDS=n (dial stored number) command. In this

command, n is 0 or 1 representing 2 storage locations and x is the stored

number.

The dial string may contain up to 40 characters.

\Gn Modem Port Flow Control

The AT\Gn command determines whether XON/XOFF flow control

will be used.

\G0

Returns OK for compatibility (default)

Not supported; returns ERROR

\G1

\Jn Adjust BPS Rate Control

\J0

Turn off feature (default)

Turn on feature

\J1

Modem Reference 6-19

\Kn Break Control

The AT\Kn command determines how the modem processes a Break

signal received from the local DTE during a connection (online).

\K5

Modem sends Break to remote modem in sequence

with transmitted data, non-destructive/non-expedited

(default)

\Nn Error Mode Control Selection

The AT\Nn command sets the type of error correction supported by the

modem when sending or receiving data.

\N0

\N1

\N2

Buffered mode. No error control (same as &Q6).

Buffered mode (same as \N0)

LAPM, MNP or disconnect mode. This is also known

as reliable mode.

\N3

LAPM, MNP, or buffered (default). The modem

attempts to connect in LAPM error control mode. If

this fails, the modem attempts to connect in MNP

mode. If this fails, the modem connects in buffered

mode and continues operation. This is also known as

V.42 auto-reliable mode (same as &Q5)

\N4

\N5

LAPM or disconnect. The modem attempts to connect

in LAPM error control mode. If this fails, the call will

be disconnected.

MNP or disconnect mode. The modem attempts to

connect using MNP 2-4 error control procedures. If

this fails, the modem disconnects. This is also known as

MNP reliable mode.

\Qn Local Flow Control Selection

The AT\Qn command sets the type of flow control used on the serial

port to adjust for differences in modem port speed.

\Q0

\Q1

\Q3

Disables flow control (same as &K0)

Sets flow control to XON/XOFF (same as &K4)

RTS/CTS to DTE (default; same as &K3)

6-20 PRO/100 LAN+Modem PC Card User’s Guide

\Tn Inactivity Timer Limit

The AT\Tn command specifies length of time (in minutes) that the

modem waits before disconnecting when no data is sent or received. The

time period can be set at n = 0 - 255. A setting of zero disables the timer.

As an alternative, the timer may be specified in S-Register S30. This

function is only applicable in buffer mode.

\Xn XON/XOFF Pass Through

\X0

Modem process XON/XOFF flow control characters

locally (default)

\X1

Not supported; returns ERROR

%B View Numbers in Blacklist

If blacklisting is in effect, the AT%B command displays the numbers for

which the last call attempted in the past two hours failed. In countries that

do not require blacklisting, this command returns ERROR.

%Cn Data Compression Control

The AT%Cn command determines the operation of V.42bis and MNP

class 5 data compression. Online changes do not take effect until a

disconnect occurs.

%C0

V.42bis/MNP Class 5 compression disabled (no data

compression)

%C1

%C2

%C3

MNP Class 5 compression enabled (no V.42bis)

V.42bis compression enabled (no MNP Class 5)

V.42bis/MNP Class 5 data compression enabled

(default)

-Cn Data Calling Tone

Data calling tone is a tone of a certain frequency and cadence specified in

V.25 that allows remotes data/fax/voice discrimination. The frequency is

1300 Hz with a cadence of 0.5 seconds on and 2 seconds off.

-C0

Disables calling tone (default)

Enables calling tone

-C1

Modem Reference 6-21

Note

Some countries do not permit calling tone to be disabled.

+GCAPRequest Complete Capabilities List

Syntax:

AT+GCAP

AT+GCAP=?

This command displays one or more lines of information text, in a

standard format, describing the basic capabilities of the modem. This

allows a software package to determine which groups of extended-syntax

commands the modem supports. The response may contain one or more

of the following responses:

+CGSM GSM (+C) commands.

+DS

+ES

Data Compression (+D) commands.

Eror Control (+E) commands.

+FCLASS Fax (+F) commands.

+MS

Modulation Control (+M) commands.

Wireless (+W) commands

+GCAP=? may be used to determine whether the modem supports the

+GCAP command: an OK response indicates support, ERROR indicates

non-implementation.

+GCI Country of Installation

Syntax:

AT+GCI=<T.35 code>

AT+GCI?

AT+GCI=?

This command configures the modem for the country of use, selecting

operational parameters and ensuring conformity to the requirements of

the selected country’s telephone network. The +GCI parameter may only

be changed when the modem is in an idle state.

<T.35 code> refers to the 8-bit hexadecimal number next to the country

in the list below.

To determine which countries are currently supported, use AT+CGI=?

The command will respond with the T.35 codes for the countries sup-

6-22 PRO/100 LAN+Modem PC Card User’s Guide

ported. To determine the current country setting, use AT+GCI? The

command will respond with the T.35 code for the country selected.

To change the current country selection, use AT+GCI=<T.35 code>

Country

Australia

Austria

<T.35 code>

Belgium

Canada

China

Denmark

Finland

France

Germany

Hong Kong

Indonesia

Ireland

Italy

Japan

Korea

Malaysia

Netherlands

New Zealand

Norway

Portugal

Singapore

Spain

Sweden

Switzerland

Taiwan

Thailand

United Kingdom

United States

Modem Reference 6-23

+GMIRequest Manufacturer Identification

Syntax:

AT+GMI

AT+GMI=?

This command displays one or more lines of information text, identifying

the manufacturer of the modem. +GMI=? may be used to determine

whether the adapter supports the +GMI command: an OK response

indicates support, ERROR indicates non-implementation.

+GMM

Request Model Identification

Syntax:

AT+GMM

AT+GMM=?

This command displays one or more lines of information text, identifiying

the modem model. +GMM=? may be used to determine whether the

modem supports the +GMM command: an OK response indicates

support, ERROR indicates non-implementation.

+GMR

Request Revision Identification

Syntax:

AT+GMR

AT+GMR=?

This command displays one or more lines of information text, identifiying

the revision level of the firmware of the modem. +GMR=? may be used

to determine whether the adapter supports the +GMR command: an OK

response indicates support, ERROR indicates non-implementation.

+MS Modulation Selection

The AT+MS parameter controls data modulations and bit rates that may

be negotiated between a local and remote modem. It accepts four

subparameters.

Syntax:

AT+MS=<carrier>,<automode>,<min_rate>,<max_rate>

AT+MS?

AT+MS=?

+MS?

Reports the current settings of subparameters

6-24 PRO/100 LAN+Modem PC Card User’s Guide

+MS=?

Displays range of acceptable values for each

subparameter

Specifies the preferred modulation to be used in

originating or answering a connection. The

<carrier> subparameter is an unquoted string

of characters. If the <carrier> parameter is

specified, the other subparameters will revert to

factory defaults. If <carrier> is omitted, any

unspecified parameters will keep their current

values (for example, AT+MS=,0 or

AT+MS=,,,2400).

Values accepted for <carrier> are the following:

B103

B212

V21

Bell 103 (300bps)

Bell 212A (1200bps)

ITU-T V.21 (300bps)

ITU-T V.22 (1200bps)

ITU-T V.22bis (2400bps)

V22

V22B

V23C

ITU-T V.23 with constant carrier (1200/75 or 75/

1200bps)

V32

ITU-T V.32 (4800 or 9600bps)

V32B

ITU-T V.32bis (4800 - 19200bps)

V34

ITU-T V.34 (2400 - 33600bps)

K56

(default) Lucent/Rockwell K56flex (32000 - 56000bps)

Enables or disables negotiation of an alternative

<carrier> if the preferred modulation is not

available.

Values accepted for <automode> are the following:

Disabled. Modem will disconnect if it is unable to

negotiate a connection with the specified <carrier>.

Enabled (default). If the specified <carrier> is unavail-

able, modem will attempt to negotiate an alternative

carrier as appropriate.

Modem Reference 6-25

Specifies the lowest bit rate at which the

modem may establish a connection. (This value

is fixed at zero for the EtherExpress™ PRO/

100 LAN/Modem PC Card Adapter.)

<min_rate>

<max_rate>

Specifies the highest bit rate at which the

modem may establish a connection. For

modulations that support only a fixed bit rate

(such as V.22bis), <max_rate> has a fixed value

to which it defaults. If the default rate or a rate

other than zero is specified, the modem will

return ERROR. This subparameter accepts the

following values: 0, 300, 1200, 2400, 4800, 7200,

9600, 12000, 14400, 16800, 19200, 21600,

24000, 31200, 33600bps. If unspecified (set to

0), <max_rate> is determined by the value of

<carrier>.

If the <carrier> setting is K56, the <max_rate>

subparameter should be left at the default value

(zero).

S-Register Reference

This section provides information on all the S-Registers supported by the

Intel EtherExpress™ PRO/100 LAN/Modem PC Card Adapter. It is

divided into two parts:

• Introduction to S-Registers

• S-Register Reference (in numerical order)

Introduction to S-Registers

The Intel EtherExpress™ PRO/100 LAN/Modem PC Card Adapter uses

memory storage locations, or S-Registers, to hold information controlling

its operating environment. Few of these S-Registers require attention from

modem users.

Some of the S-Registers are reserved. These either contain parameter bit

maps for the internal use of the modem or are not in current use. Gener-

ally, modem users should not alter or write to any of these reserved

6-26 PRO/100 LAN+Modem PC Card User’s Guide

S-Registers because doing so could result in the modem behaving unpre-

dictably.

To display the value of an S-Register, type ATSn? where n is the number

of the S-Register, then press Enter.

To modify the value of an S-Register, type ATSn=r where n is the S-

S-Register Reference

S0 Ring to Answer After

The contents of register S0 sets the number of rings required before

the modem goes off-hook to answer an incoming call (auto answer).

The value can range from 0 to 255. ATS0=0 disables the auto-

answer function. The default is 0.

S1 Ring Counter

This register is read only. The value of S1 increments with each ring.

If no rings occur over a six-second interval, the register is cleared.

The value of S1 can range from 0 to 255. The default is 0. Limits are

country specific.

S2 AT Escape Character

quence. This command is used to return to command mode without

losing the connection with a remote modem. Default is S2=43,

which is the “+” character. Thus the default Escape sequence is

+++. ASCII values 127 and below can be used. To disable this

Escape sequence, set S2 equal to a value greater than 127.

S3 Command Line Termination Character

This register contains the ASCII value of the command line

terminating character (carriage return). The factory default value is

ASCII 13 — the carriage return character. You can set register S3

to any value between 0 and 127.

Modem Reference 6-27

S4 Response Formatting Character

This register contains the ASCII value of the line feed character.

The factory default value is 10. You can set register S4 to any value

between 0 and 127. The modem uses a line feed character in

command mode when it responds to the computer.

S5 Command Line Editing Character

This register contains the ASCII value of the backspace character

and is applicable to asynchronous transmissions only. The factory

default value is 8. You can set register S5 to any value between 0

and 32, or to 127. The modem will not recognize the backspace

character if it is set to a value greater than ASCII 32.

S6 Wait Before Blind Dialing

This register determines how long the modem waits after going off-

hook before dialing the first digit. The wait must be at least 2

seconds. Register S6 can be set to any value between 2 and 65

seconds. The default is 2 seconds. The value of the W dial modifier

will override the value in register S6. This operation, however, may

be affected by some ATX options according to country restrictions.

Defaults and limits are country-specific.

S7 Connection Completion Time-Out

This register determines the number of seconds the originating

modem waits for a carrier signal from the answering modem before

hanging up. The timer is started when the modem finishes dialing

(originate), or goes off-hook (answer). In originate mode, the timer

is reset upon detection of an answer tone if allowed by country

restriction. The timer also specifies the wait for silence time with the

@ dial modifier (in seconds). S7 is not associated with the W dial

modifier. Register S7 can be set at from 1 to 255 seconds with a

default of 50 seconds. Defaults and limits are country-specific.

6-28 PRO/100 LAN+Modem PC Card User’s Guide

S8 Duration of Pause for Comma Dial Modi-

fier

This register determines the number of seconds to pause for each

comma (,) in a dial string or command line. The default is 2

seconds, but any value from zero to 65 is acceptable. Defaults and

limits are country-specific.

S10 Delay Between Lost Carrier/Hang Up

This register specifies the time (in tenths of a second) that the

modem waits after carrier loss before hanging up. The default is 20

(2.0 seconds). This allows for temporary carrier loss without causing

the local modem to disconnect. Register S10 will accept a value

ranging from 1 to 254 in tenths of a second (0.1 to 25.4 seconds).

Defaults and limits are country-specific.

S11 DTMF Tone Duration

This register determines the “touch tone” dialing speed which is

prefixed for each country. The value can range from 50 to 150

milliseconds. The default is 95 milliseconds. The value of register

S11 has no effect on pulse dialing. Defaults and limits are country-

specific.

S12 Escape Guard Time

This register sets the value (in 20 ms increments) of the required

pause after the escape sequence. Range is 0 = 255, default is 50 units

of 0.02 seconds each, or one second.

S28 V.34 Modulation Enable/Disable

This register enables or disables V.34 modulation. Default setting is

1, valid values are 0 or 1. A value of zero disables V.34 modulation.

Any other value in the range enables it.

S30 Inactivity Timer

The value specified by this register sets how long the modem will

wait (in minutes) before disconnecting when no data is sent or

received. This function is only applicable in buffer mode. It is set

Modem Reference 6-29

by AT\Tn. Values are 0-255. Default is 0 (disabled).

S34 DTE Throughput Limit

This register specifies whether the modem should limit throughput

when the DTE is operating at higher speeds (57,600 or 115,200bps)

S34=0

Do not limit throughput (default).

Limit throughput to DTE speed.

S34=1

S35 Data Calling Tone

This register enables or disables a tone of a certain frequency and

cadence as specified in V.25 that allows remote data/fax/voice

discrimination. It is set by AT-Cn. The frequency is 1300 Hz with a

cadence of 0.5 seconds on and 2 seconds off. The default is

country-specific. Some countries do not allow data calling tone to be

overridden.

S35=0

S35=1

Data calling tone disabled (default)

Data calling tone enabled

S36 Negotiation Fallback

This register specifies the action to be taken in the event of a

negotiation failure when error control is selected.

S36=0,2

S36=1,3

S36=4,6

S36=5,7

Hang up

Fall back to an asynchronous connection

Attempt MNP. If MNP fails, hang up.

Attempt MNP. If MNP fails, fall back to asynchronous

connection. Default is 7.

S37 Dial Line Rate

S37=0

S37=1

S37=2

S37=3

S37=4

Maximum modem speed (default)

Reserved

1200/75bps

300bps

Reserved

6-30 PRO/100 LAN+Modem PC Card User’s Guide

S37=5

Attempt to connect at 1200bps

Attempt to connect at 2400bps

Attempt to connect at 4800bps

Attempt to connect at 7200bps

Attempt to connect at 9600bps

Attempt to connect at 12000bps

Attempt to connect at 14400bps

Attempt to connect at 16800bps

Attempt to connect at 19200bps

Attempt to connect at 21600bps

Attempt to connect at 24000bps

Attempt to connect at 26400bps

Attempt to connect at 28800bps

Attempt to connect at 31200bps

Attempt to connect at 33600bps

S37=6

S37=7

S37=8

S37=9

S37=10

S37=11

S37=12

S37=13

S37=14

S37=15

S37=16

S37=17

S37=18

S37=19

S40 ETC Startup Autorating

S40=0

S40=1

S40=2

Start up with normal autorating (default)

Start up at initial rate of 4800 or below

Start up at initial rate of 9600 or below

S42 Auto Rate

V.32bis and V.22bis auto rate is disabled. Retrain operation is disabled or

enabled in date mode, and fallback is disabled in data mode.

S42=0

Auto rate disabled

S42=1

Auto rate enabled (default)

S43 Auto Mode

V.32bis startup auto mode operation disabled.

S43=0

Auto mode disabled

S43=1

Auto mode enabled (default)

Modem Reference 6-31

S46 Data Compression Selection

The setting of this register is used to turn data compression on or

off. It is set by AT%Cn.

Data compression can only be enabled when the modem is operat-

ing in an error-control (EC) mode using either V.42 LAP-M or

MNP protocols.

S46=0

Modem will not attempt negotiation for data compres-

sion

S46=2

Modem will negotiate with a remote modem for data

compression (default).

S46=136 Same as S46=0

S46=138 Same as S46=2

S48 LAPM Error Control and Feature Nego-

tiation

S48=7

Negotiation enabled

S48=128 Negotiation disabled; forces immediate fallback options

specified in S36.

The following table shows the S36 and S48 configuration settings needed

to negotiate certain types of connections.

S48=7

S48=128

do not use

buffered

S36=0,2

S36=1,3

S36=4,6

S36=5,7

LAPM or hangup

LAPM or buffered

LAPM, MNP, or hangup MNP or hangup

LAPM, MNP, or buffered MNP or buffered

S89 Timer to Control Sleep Mode

This register displays the number of seconds of inactivity (no

characters sent from DTE, no RING) in the off-line command state

before the modem places itself into standby mode. A value of zero

prevents standby mode. Default is 30. Range is 0 and 5 - 65.

6-32 PRO/100 LAN+Modem PC Card User’s Guide

S91 Line Transmit Level

This register is effective only for Japan. It specifies the line transmit

level, in dB, with an implied minus sign. Default is 15 dB, range is 6

- 15.

S92 Direct Connect Transmit Level

This register sets the transmit level, in dBm, for direct connect

cellular. This value may have different settings for different phones.

Default is 0 dBm.

S95 Negotiation Message Options

This register enables various result codes indicating the sequence of

events in an error-controlled connection. This S-Register does not

affect the way the connection is negotiated, it just enables extended

messages.

S95=0

Disables extended result code messages.

S95=1

Use DCE (modem-to-modem) speed when reporting

CONNECT result codes.

S95=2

Append “/ARQ” to CONNECT result code when an

error-controlled (EC) connection is established.

S95=4

S95=8

S95=32

Enable CARRIER result codes.

Enable PROTOCOL result codes.

Enable COMPRESSION result codes.

S98 Cable Detection Options

This register controls the automatic detection and reporting of

changes in the cable or minidock attached to the modem.

S98=0

S98=1

S98=2

Disables cable detection and reporting.

Enable cable detection; disable reporting.

Enable cable detection and reporting.

APPENDIX A

Automated Customer Support

You can reach Intel’s automated support services 24 hours a day, every

day at no charge. The services contain the most up-to-date information

about Intel products. You can access installation instructions,

troubleshooting information, and general product information.

World Wide Web &

Internet FTP

Intel Bulletin Board

Service (BBS)

Access Intel’s World Wide Web

home pages or download

information using anonymous FTP.

Use Intel’s BBS. Dial

in by modem at 8-N-1,

and up to 14.4 Kbps.

Troubleshooting

Software updates

Installation notes

Product information

How to access:

✓

See web addresses on next page.

US and Canada:

1-503-264-7999

Europe:

+44-1793-432955

Worldwide:

+1-503-264-7999

A-2 PRO/100 LAN+Modem PC Card User’s Guide

Intel Web and Internet Sites

Support: http://support.intel.com

News: news://cs.intel.com

Network Products: http://www.intel.com/network

Corporate: http://www.intel.com

FTP Host: download.intel.com

FTP Directory: \enduser_reseller\etherexpress_lan_adapters

Intel Customer Support Technicians

Other support services: You can purchase a range of support

services, including 24 hour support, per incident support, on-site

service, and software and hardware maintenance agreements. For

details about the Intel Support Service options, download document

8549 from one of the automated services.

Worldwide access: Intel has technical support centers worldwide.

Many of the centers are staffed by technicians who speak the local

languages. For a list of all Intel support centers, the telephone numbers,

and the times they are open, download document 9089 from one of the

automated services.

If you don’t have access to automated services, contact your local

dealer or distributor. Or call +1-916-377-7000 from 07:00 to 17:00

Monday - Friday, U.S. Pacific Time.

APPENDIX B

Specifications

General Specifications

Size:

3.37 in x 2.13 in x 0.197 in (85.6 mm x

54.0 mm x 5.0 mm)

Weight:

1.47 oz (42.1 g)

Temperature range:

Operating:

32°F to 131°F (0°C to 55°C)

-4°F to 149°F (-20°C to 65°C)

95% maximum noncondensing

512K flash memory, 160K SRAM

Storage:

Humidity:

Memory size:

Memory alloc.:

4K shared memory allocated to D2000-

D2FFF (default)

Power:

+5 VDC, 490 mA typical

Self test capability

Diagnostics:

Approvals:

FCC Part 15, Class B, FCC Part 68,

Industry Canada, CE Mark

B-2 PRO/100 LAN+Modem PC Card User’s Guide

Modem Specifications

Data modulation:

V.34 from 33,600 down to 2400 bps,

V.32terbo with trellis coding at 19200

and 16800 bps; V.32bis (with trellis

coding at 14400, 12000, 9600, and 7200

bps; uncoded at 4800 bps); V.32 (with

trellis coding at 9600 bps, uncoded at

4800 bps); V.23 at 1200/75 and 75/

1200 bps; V.22bis at 2400 bps; V.22 at

1200 bps; Bell 212A at 1200 bps

Fax modulation:

Compatible with Class 1 software; V.17

at 14400, 12000, 9600, 7200, and 4800

bps; V.29 at 9600, 7200, and 4800 bps;

V.27ter at 4800 and 2400 bps

Fax support:

Group 3, EIA/TIA Class 1

Error control:

V.42 Error Control, MNP Levels 2-4

Error Detection

Data compression:

Diagnostics:

V.42bis (4:1) or MNP Level 5 (2:1)

Power-up self tests of program RAM,

data RAM, and nonvolatile memory.

Nonvolatile RAM:

1 user definable profile; 2 thirty-six

digit telephone numbers; LAN Adapter

ID and serial number

Command set:

Data interface:

Hayes and Microcom compatible AT

commands

PCMCIA Release 2.1 compliant, 68-pin

connector

Analog interface:

DTE speeds:

RJ-11C modular telephone connector

1200, 2400, 4800, 7200, 9600, 14400,

19200, 37400, 57600, and 115200 bps

APPENDIX C

Limited Lifetime Warranty

Intel warrants to the original owner that the hardware product delivered

in this package will be free from defects in material and workmanship.

This warranty does not cover the product if it is damaged in the process

of being installed or improperly used.

THE ABOVE WARRANTY IS IN LIEU OF ANY OTHER WARRANTY,

WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING BUT

NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY,

FITNESS FOR A PARTICULAR PURPOSE ARISING OUT OF ANY

PROPOSAL, SPECIFICATION, OR SAMPLE.

This warranty does not cover replacement of adapter products damaged by

abuse, accident, misuse, neglect, alteration, repair, disaster, improper installation,

or improper testing. If the product is found to be otherwise defective, Intel, at

its option, will replace or repair the product at no charge except as set forth

below, or refund your purchase price provided that you deliver the product

along with a Return Material Authorization (RMA) number (see below), along

with proof of purchase (if not registered), either to the dealer from whom you

purchased it or to Intel with an explanation of any deficiency. If you ship the

product, you must assume the risk of damage or loss in transit. You must use

the original container (or the equivalent) and pay the shipping charge. Intel may

replace or repair the adapter product with either new or reconditioned parts, and

any part or product replaced becomes Intel’s property. Repaired or replaced

products will be returned at the same revision level as received or higher, at

Intel’s option. Intel reserves the right to replace discontinued product with an

equivalent current generation product.

This warranty gives you specific legal rights and you may have other rights

which vary from state to state. All parts or components contained in this

hardware product are covered by Intel’s limited warranty for this product; the

product may contain fully tested, recycled parts, warranted as if new. For

warranty information call one of the numbers below.

Returning a defective product

From North America:

Before returning any product, contact Intel Customer Support and obtain a

Return Material Authorization (RMA) number by calling +1-916-377-7000.

C-2 PRO/100 LAN+Modem PC Card User’s Guide

If the Customer Support Group verifies that the product is defective, they will

have the RMA department issue you an RMA number to place on the outer

package of the product. Intel cannot accept any product without an RMA

number on the package.

All other locations:

Return the product to the place of purchase for a refund or replacement.

INTEL ADAPTER MONEY-BACK GUARANTEE (North

America Only)

Intel wants you to be completely satisfied with the Intel adapter product that you

have purchased. Any time within ninety (90) days of purchase, you may return

your Intel adapter to the original place of purchase for a full refund of the

purchase price from your dealer. Resellers and Distributors, respectively,

accepting returns and refunding money back to their customers may return Intel

adapters to their original place of purchase. Intel guarantees that it will accept

returns under this policy and refund the original purchase price to customers

purchasing directly from Intel.

Limitation of Liability and Remedies

INTEL SHALL HAVE NO LIABILITY FOR ANY INDIRECT,

SPECULATIVE, CONSEQUENTIAL, INCIDENTAL, PUNITIVE OR

SPECIAL DAMAGES ARISING FROM THE USE OF OR INABILITY TO

USE THIS PRODUCT INCLUDING, WITHOUT LIMITATION, LOSS OF

USE, BUSINESS INTERRUPTIONS, LOSS OF PROFITS, AND LOSS OF

GOODWILL, WHETHER ANY SUCH DAMAGES ARISE OUT OF

CONTRACT NEGLIGENCE, TORT, OR UNDER ANY WARRANTY,

IRRESPECTIVE OF WHETHER INTEL HAS ADVANCE NOTICE OF

THE POSSIBILITY OF ANY SUCH DAMAGES. NOTWITHSTANDING

THE FOREGOING, INTEL’S TOTAL LIABILITY FOR ALL CLAIMS

UNDER THIS AGREEMENT SHALL NOT EXCEED THE PRICE PAID

FOR THE PRODUCT. THESE LIMITATIONS ON POTENTIAL

LIABILITIES WERE AN ESSENTIAL ELEMENT IN SETTING THE

PRODUCT PRICE. INTEL NEITHER ASSUMES NOR AUTHORIZES

ANYONE TO ASSUME FOR IT ANY OTHER LIABILITIES.

Some states do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitations may not apply to you.

Software provided with the hardware product is not covered under the hardware

warranty described above. See the applicable software license agreement which

shipped with the adapter product for details on any software warranty.

April 28, 1994

APPENDIX D

Agency Notices

FCC Compliance Statement

FCC Rules and Regulations - Part 15

This product has been tested and found to comply with the limits for a Class B

computing device pursuant to Part 15 of the FCC rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. Installed correctly, it probably will not interfere with radio

or TV reception. However, we do not guarantee the absence of interference.

This product generates and uses energy of about the same frequency as

radio and TV broadcasts. Installed incorrectly, it may interfere with

reception of radio and TV broadcasts.

If you suspect this product is causing interference, turn your computer

on and off while the radio or TV is showing interference. If the

interference disappears when you turn the computer off and reappears

when you turn the computer on, something in the computer is causing

interference.

To reduce interference, try these suggestions:

•

Change the direction of the radio or TV antenna.

Move the computer, radio or TV. For example, if the computer is

to the right of the TV, move it to the left of the TV. Or move

them farther apart.

•

Plug the computer into a different electrical outlet than the radio

or TV.

Ensure that all expansion slots (on the back or side of the

computer) are covered. Also ensure that all metal retaining

brackets are tightly attached to the computer.

D-2 PRO/100 LAN+Modem PC Card User’s Guide

NOTE

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

CAUTION

If the device is changed or modified without permission from Intel, the

user may void his or her authority to operate the equipment.

FCC Rules and Regulations - Part 68

This equipment complies with Part 68 of the FCC Rules. On the back of the

EtherExpress PRO/100 LAN+Modem PC Card is a label that contains, among

other information, the FCC Registration Number and Ringer Equivalency

Number (REN) for this equipment. You must, upon request, provide this

information to your telephone company.

The REN is useful to determine the quantity of devices you may connect to

your telephone line and still have all those devices ring when your telephone

number is called. In most but not all areas, the sum of the RENs of all devices

connected to one line should not exceed five (5.0). To be certain of the number

of devices you may connect to your line, as determined by the REN, you should

contact your local telephone company to determine the maximum REN for your

calling area.

If your telephone equipment causes harm to the telephone network, the

telephone company may discontinue your service temporarily. If possible, they

will notify you in advance. But if advance notice is not practical, you will be

notified as soon as possible. You will be informed of your right to file a

complaint with the FCC.

Your telephone company may make changes in its facilities, equipment,

operations or procedures that could affect the proper functioning of your

equipment. If they do, you will be notified in advance to give you an opportunity

to maintain uninterrupted telephone service.

If you experience trouble with this telephone equipment, please contact Intel

Customer Support, at 916-377-7000 for information on obtaining service or

repairs. The telephone company may ask that you disconnect this equipment

from the network until the problem has been corrected or until you are sure that

the equipment is not malfunctioning.

There are no user serviceable parts contained in this equipment.

This equipment may not be used on coin service provided by the telephone

company. Connection to party lines is subject to state tariffs.

Agency Notices D-3

Canadian compliance (Industry Canada)

When tested in at least one intended host:

This digital apparatus does not exceed the Class B limits for radio noise

emissions from digital apparatus set out in the interference-causing

equipment standard entitled “Digital Apparatus”, ICES-003 of the

Canadian Department of Communications.

Cet appareil numérique respecte les limites bruits radioélectriques

applicables aux appareils numériques de Class B prescrites dans la norme

sur le matériel brouilleur: “Appareils Numériques”, NMB-003 édictée

par le Ministre Canadien des Communications.

NOTICE: The Industry Canada (IC) label identifies certified equipment. This

certification means that the equipment meets telecommunications network

protective, operational and safety requirements as prescribed in the appropriate

Terminal Equipment Technical Requirements document(s). The department

does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be

connected to the facilities of the local telecommunications company. The

equipment must also be installed using an acceptable method of connection.

The customer should be aware that compliance with the above conditions may

not prevent degradation of service in some situations.

Repairs to certified equipment should be coordinated by a representative

designated by the supplier. Any repairs or alterations made by a user to this

equipment, or equipment malfunctions, may give the telephone communications

company cause to request the user to disconnect the equipment.

Users should ensure for their own protection, that the electrical ground

connections of the power utility, telephone lines and internal metallic water pipe

system, if present, are connected together. This precaution may be particularly

important in rural areas.

Caution: Users should not attempt to make such connections themselves, but

should contact the appropriate electric inspection authority, or electrician, as

appropriate.

NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal

device provides an indication of the maximum number of terminals allowed to

be connected to a telephone interface. The termination on an interface may

consist of any combination of devices subject only to the requirement that the

sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.

REN: See back of unit.

D-4 PRO/100 LAN+Modem PC Card User’s Guide

Manufacturer declaration

This certifies that Intel EtherExpress PRO/100 Mobile Adapters

comply with the EU Directive 89/336/EEC, using the EMC standards

EN55022 (Class B) and EN50082-1. This product also meets or exceeds

EN60950 safety requirements.

This product has been tested and verified to meet CISPR 22 Class B

requirements.

Intel Corporation

Network Products Division - MS JF3-446

2111 N.E. 25th Ave.

Hillsboro, Oregon 97124

APPENDIX E

Software License Agreement

BY USING THIS SOFTWARE, YOU ARE AGREEING TO BE

BOUND BY THE TERMS OF THIS AGREEMENT. DO NOT USE

THIS SOFTWARE UNTIL YOU HAVE CAREFULLY READ AND

AGREED TO THE FOLLOWING TERMS AND CONDITIONS. IF

YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT,

PROMPTLY RETURN THE SOFTWARE PACKAGE AND ANY

ACCOMPANYING ITEMS.

LICENSE: Intel Corporation (“Intel”) grants you the non-exclusive

right to use the enclosed software program (the “Software”). You will

not use, copy, modify, rent, sell or transfer the Software or any portion

thereof except as provided in this Agreement.

You may:

1. Install/use the Software on a single computer or on a single local

area network (“LAN”) server;

2. Copy the Software solely for backup or archival purposes,

including copying the Software into memory.

RESTRICTIONS:

You Will Not:

1. Sublicense the Software;

2. Reverse engineer, decompile, or disassemble the Software;

3. Copy the Software, in whole or in part, except as provided in this

Agreement.

E-2 PRO/100 LAN+Modem PC Card User’s Guide

TRANSFER: You may transfer the Software to another party if the

receiving party agrees to the terms of this Agreement and you retain no

copies of the Software and accompanying documentation. Transfer of

the Software terminates your right to use the Software.

OWNERSHIP AND COPYRIGHT OF SOFTWARE: Title to the

Software and all copies thereof remain with Intel or its vendors. The

Software is copyrighted and is protected by United States and

international copyright laws. You will not remove the copyright notice

from the Software. You agree to prevent any unauthorized copying of

the Software.

DUAL MEDIA SOFTWARE: If the Software package contains

multiple media, you may only use the disks appropriate for your single-

user computer or LAN.

WARRANTY: The Software is provided “AS IS.” Intel warrants that

the media on which the Software is furnished will be free from defects

in material and workmanship for a period of one (1) year from the date

of purchase. Upon return of such defective media, Intel’s entire liability

and your exclusive remedy shall be the replacement of the Software.

THE ABOVE WARRANTIES ARE THE ONLY WARRANTIES

OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR

ANY PARTICULAR PURPOSE.

LIMITATION OF LIABILITY: NEITHER INTEL NOR ITS

VENDORS SHALL BE LIABLE FOR ANY LOSS OF PROFITS,

LOSS OF USE, LOSS OF DATA, INTERRUPTIONS OF

BUSINESS, NOR FOR INDIRECT, SPECIAL, INCIDENTAL OR

CONSEQUENTIAL DAMAGES OF ANY KIND WHETHER

UNDER THIS AGREEMENT OR OTHERWISE, EVEN IF

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

AUDIT: Intel reserves the right to have audits conducted to verify your

compliance with this Agreement.

TERMINATION OF THIS LICENSE: Intel may terminate this

license at any time if you are in breach of any of its terms and

conditions. Upon termination, you will immediately destroy the

Software or return all copies of the Software and documentation to

Intel.

Software License Agreement E-3

U.S. GOVERNMENT RESTRICTED RIGHTS: The Software and

documentation were developed at private expense and are provided

with “RESTRICTED RIGHTS.” Use, duplication, or disclosure by the

Government is subject to restrictions as set forth in FAR 52.227-14 and

DFAR 252.227-7013 et seq. or its successor.

EXPORT LAWS: You agree that the distribution and export/re-export

of the Software is in compliance with the laws, regulations, orders or

other restrictions of the U.S. Export Administration Regulations.

APPLICABLE LAW: This Agreement is governed by the laws of the

State of California and the United States, including patent and

brought in Santa Clara County, California.

E-4 PRO/100 LAN+Modem PC Card User’s Guide

Index

Symbols

100Base-TX Ethernet 1-4

10Base-T Ethernet network 1-4

56Kbps

connections 1-1

technology 1-1

Advanced Look-ahead Pipelining 4-45

Alphabetical reference, NOSes 4-3

America Online 5-8

Analog telephone line 1-5

Artisoft LANtastic 4-4

installation 4-4

AT Command Reference 6-4

AT commands

reference 6-1

AT&T StarGROUP

installation 4-4

auto-sensing, speed 1-2

Banyan VINES

installation 4-5

Banyan VINES Dial-In 5-10

CAB files, Windows 95 2-2

Cabling

data grade 1-2

Card and Socket Services 4-51

Card Information Structure (CIS) 4-48

CARRIER message 6-3

Category 5 cabling 1-2

Index-2

COM port

automatic detection 4-33

setting with COMx 4-33

COM Port Monitor 5-5

COMBASE keyword 4-35, 4-43, 4-48, 4-57

COMIRQ keyword 4-35, 4-43, 4-48, 4-57

Communications application notes 5-6

CompuServe WINCIM 5-10

Computer-specific application notes 4-60

COMx keyword 4-33, 4-43

Conflicts, memory 4-35

CONNECT message 6-1

Country Identifier utility 5-1

Country of installation codes 6-21

Customer Support A-1

Data compression 4-31

DCOMPVLM.BAT 4-19, 4-26, 4-30

DEC PATHWORKS 4-6

Default values 4-3

Diagnostics 5-3

Dial modifiers 6-6

Dial-Up Product Registration 5-2

Digital telephone line 1-5

Digital telephone lines 1-7

DOS modem software 4-57

Early receive (RX) 4-45

Early transmit (TX) 4-46

EMM386 4-35, 4-36, 4-51

EMMEXCLUDE= statement 4-36

Error control 4-31

Fax/modem 4-31

FRAME keyword 4-44

Index-3

FTP LANWatch

installation 4-9

NDIS driver 4-10

Packet driver 4-10

FTP PC/TCP 4-11

and NetWare 4-15

installation 4-11

Packet driver 4-14

Generic installation 4-16

Hardware installation requirements 1-3

Hayes 4-31

Hayes commands 6-1

Heat during normal use 1-6

HotSwap 1-3

HP LAN Manager

installation 4-16

IBM DOS LAN Requestor 4-19

IBM Local Area Network Support Program 4-16

installation 4-16, 4-17

IBM Local Area Support Program 4-16

IBM PC LAN 4-19

Indicator lights

LAN adapter cable 1-8

modem cable 1-7

Installation

generic 4-16

manual 4-19

Microsoft Windows 3.x 4-2

Novell NetWare 4-2

Program, Intel 4-2

Program, Xircom 4-22

VLM shell 4-2

Index-4

Installation Program 1-2, 4-3

Intel Web and Internet Sites B-2

INTERRUPT keyword 4-44, 4-48

INTERRUPTNUMBER keyword 4-44

IOADDRESS keyword 4-44

IOBASEADDRESS keyword 4-44

IOWAITSTATES keyword 4-44

K56flex technology 1-1

LAN card 4-31

LAN Manager

Microsoft LAN Manager 4-20

Ungermann-Bass Net/One 4-28

LANtastic, Artisoft 4-4

LANWatch, FTP 4-9

LapLink 5-11

LEDs

LAN adapter cable 1-8

modem cable 1-7

LINKDISABLE keyword 4-44

LINKINTEGRITY keyword 4-44

Lotus

cc:Mail 5-13

Notes 5-15

M16BTEST.EXE 5-3

Manual installation 4-19

Memory

conflicts 4-35

keyword 4-45

manager 4-35

MEMORYBASEADDRESS keyword 4-45

MEMWAITSTATES keyword 4-45

Microcom 4-31

Microsoft

Index-5

Windows for Workgroups. See Windows for Workgroups

Microsoft LAN Manager

installation 4-20

Microsoft Remote Access Server (RAS) 5-17

Microsoft Windows 3.x

installation 4-2

MODE keyword 4-45, 4-47

Models 1-2

Modem

driver 4-36

driver example 4-37

driver parameters 4-36

reference information 4-31

sound 4-60

volume levels 4-60

Modem commands 6-4

Modem result codes 6-1

Modem script files 5-6

Modem setup 5-7

Modem Test utility 5-2

MODEMLOG.TXT 2-12

NDIS 3.0 driver

parameters 2-13, 3-8

NDIS driver

Artisoft LANtastic 4-4

FTP LANWatch 4-9

FTP PC/TCP 4-11

generic 4-16

Microsoft LAN Manager 4-20

Microsoft Windows for Workgroups 4-21

parameters 4-40

SunSoft PC-NFS 4-27

Ungermann-Bass Net/One LAN Manager 4-28

Wollongong PathWay Access for DOS 4-29

NET.CFG file 4-38

example 4-38

Index-6

NetWare. See Novell NetWare

installation with Windows 95 2-8

Network

drivers 4-3

operating system 1-2, 4-3

network node address 5-4

NETX shell support 4-2

NO CARRIER message 6-1

NOCHECK keyword 4-45

NOCOM keyword 4-45

NOLEDS keyword 4-46

Novell NetWare 4-26

and FTP PC/TCP 4-15

installation 4-2

ODI driver

FTP PC/TCP 4-11

generic 4-16

loading sequence 4-39

Microsoft Windows for Workgroups 4-21

parameters 4-38

Wollongong PathWay Access for DOS 4-29

OEM Service Release Version 2 2-1

OK message 6-1

OnNet with FTP PC/TCP 4-11, 4-13

OSR2 2-1

PABX systems 1-7

Package contents 1-4

Packet driver

FTP LANWatch 4-9

FTP PC/TCP 4-11

loading sequence 4-42

parameters 4-41

Parameters, driver 2-13, 3-8, 4-1, 4-11, 4-19, 4-37

PATHWORKS, DEC 4-6

PC Card slot 1-5

PC Card Standard 1-2

Index-7

PC-NFS 4-27

PC/TCP, FTP 4-11

PCMCIA 1-2

PORT keyword 4-46

Power management 1-3

Power-saving modes

under Windows 95 2-9

Prodigy 5-19

PROTOCOL.INI file 4-40

Registry

Windows 95 2-16, 3-8

Windows NT 2-13

Required Equipment 1-4

Result codes, modem 6-1

Retail version, Windows 95 2-1

S-Register Reference 6-25

S-Registers 6-25

Script files, modem 5-6

Self test 5-3

SHAREIRQ keyword 4-35, 4-46, 4-57

Shutdown and restart 2-11

SINT keyword 4-46

SLOT keyword 4-46

SOCKET keyword 4-46, 4-47

Software supplied 1-2

Software updates B-1

SunSoft PC-NFS

installation 4-27

SYSTEM.INI file 4-36

TELSEL.EXE 5-1

Troubleshooting

Windows 95 2-9

Type II PC Card 1-3

Index-8

Ungermann-Bass Net/One

installation 4-28

Update Device Driver Wizard 2-5

Utilities 5-1

Version

Windows 95 2-1

VINES, Banyan 4-5

VLM file decompression 4-19

VLM shell 4-2

Volume, modem speaker 4-60

WinCim 5-10

Windows 3.1

installation 4-2

Windows 95 2-1

installation 2-1

troubleshooting 2-9

NetWare installation 2-8

OEM (OSR2) version 2-4

retail version 2-2

Windows NT

installation 3-3

Windows for Workgroups 4-21

ODI driver 4-22

removing old installation 4-25

with NetWare 4-22

Wizard, Update Device 2-5

Wollongong PathWay Access

installation 4-29

Wollongong PathWay Access for DOS 4-29

NDIS driver 4-30

ODI driver 4-30

WORDSIZE keyword 4-46, 4-47

World Wide Web B-1

IOGear Computer Drive GUH224 User Manual
IOGear Switch GCS614A User Manual
JBL Speaker System ECS300 User Manual
Jenn Air Cooktop 0VG4280 User Manual
Jensen Marine Radio VR209 User Manual
John Deere Spreader LPBST 35JD User Manual
JVC CRT Television AV 30W777 User Manual
JVC Speaker System CA UXZ7MDR User Manual
Kenmore Double Oven 66578002700 User Manual
Kramer Electronics TV Cables 2900 000483 User Manual