JBL® ON AIR
WEM-1
OWNER’S GUIDE
THANK YOU FOR CHOOSING
A JBL® PRODUCT
For more than 60 years, JBL, Inc., has been involved in every aspect of music
and film recording and reproduction, from live performances to the recordings
you play in your home, car or office.
UNPACKING THE SYSTEM
Carefully unpack the system. If you suspect damage from transit, report it imme-
diately to your dealer and/or delivery service. Keep the shipping carton and pack-
ing materials for future use. Open the package and verify the following contents:
Included:
®
You can be confident that the JBL system you have chosen will provide every
1 x Owner’s manual
note of enjoyment that you expected – and that when you think about purchasing
additional audio equipment, you will once again choose a JBL product.
1 x USA warranty sheet
1 x Receiver-amplifier module
on the latest JBL advancements. This also facilitates a better understanding
of JBL customers, allowing JBL engineers to design products that meet their
needs and expectations.
1 x Power supply for receiver-amplifier
1 x 120V AC power cord for receiver-amplifier power supply
1 x 230V AC power cord for receiver-amplifier power supply – Shuko plug
1 x 230V AC power cord for receiver-amplifier power supply – UK plug
1 x Handheld remote control
The JBL On Air WEM-1 is an advanced wireless system that allows you to
enjoy your favorite music in remote locations around your home, using almost
any loudspeaker. To ensure trouble-free performance, please carefully read
these instructions completely before connecting or using the system.
2 x Wall-mount brackets for receiver
1 x Pedestal – to be attached on receiver’s left side if receiver is to be
used vertically
1 x Transmitter module
1 x Power supply for transmitter
1 x 120V AC power cord for transmitter power supply
1 x 230V AC power cord for transmitter power supply – Shuko plug
1 x 230V AC power cord for transmitter power supply – UK plug
1 x 6' (1.8m) Audio stereo cable, RCA-RCA
1 x Wall-mount bracket for transmitter
2 x Panhead M3 x 4 machine screws for attaching wall-mount bracket
to transmitter
4 x Small, round, self-adhesive feet – to be attached on transmitter’s
left-side panel if transmitter is to be used vertically
1
MUTE
INPUT
0
2
3
VOL
Remote Control
Wireless Transmitter
Wireless Receiver
3
CONNECTIONS
NOTES: For the sake of simplicity, throughout this manual the term “source”
is used when describing connections and operation. This would apply to any
device such as an A/V receiver, audio component, computer or portable
music player.
Right Speaker
Left Speaker
The JBL On Air WEM-1 may be connected to your source in several ways.
First, determine how you would like to use the WEM-1; then follow the setup
instructions for that application.
Audio sources that can be used in this application may be an A/V receiver or
audio receiver, a portable audio player, or a computer featuring a sound card.
First, determine whether your source contains RCA-type preamp outputs for
the front/main channels or only speaker wire outputs. On an A/V or audio
receiver, the preamp outputs are usually indicated by RCA-type jacks on
the back of the receiver labeled as “pre-out” (please refer to your source’s
owner’s manual to confirm whether it includes preamp outputs). If your source
includes these RCA-type outputs, follow the steps in Connection Option A.
If your source features only speaker wire outputs, follow steps in Connection
Option B. If your receiver does not feature either type of outputs for the
front/main channels, it cannot be used with the WEM-1.
Figure 2.
Step 4.
Connection Option A
Plug the transmitter module and receiver module into the wall outlets, using
the power supply and correct power cord. Make sure the antennas 4E are
extended upward.
Connecting using the preamp outputs on your source:
NOTE: Make sure the power is turned off on all components.
Step 5.
Make sure the ID Code setting on the transmitter 6 is set to the same setting
as that on the receiver B. See page 5 for more information on ID codes. If
necessary, configure your receiver to activate the preamp level outputs for
the main/front channels (consult your source’s owner’s manual for specific
instructions).
Step 1.
Connect the interconnect cable (included) to the left and right front/main
preamp outputs, zone 2 outputs or REC outputs, and the inputs on the
transmitter module 7, as shown in Figure 1.
Source
When connected properly, the LED on the front of the receiver should be red
when first plugged in. When a button on the remote is pressed, the LED should
flash green until the transmitter and receiver “lock in.” It will then also light in
solid green. This LED will light in orange if the local input on the receiver is
selected (see page 5 under “Local Input” for more details).
Front/Main/Second Room
Preamp Outputs
R
L
Connection Option B
Connecting using the speaker-level outputs from your receiver:
NOTE: Make sure power is turned off on all components.
Step 1.
Connect the speaker wire to the receiver’s speaker outputs and the inputs
on the transmitter module 8, as shown in Figure 3.
Receiver
Figure 1.
Step 2.
Place the receiver module in the desired location in your home near an
AC outlet, as it needs to plug into the wall.
Step 3.
Connect speaker wire (not included) to the push terminals on the receiver
module A and to the connectors on your speakers, as shown in Figure 2.
Please note that speaker wire features some form of a polarity indicator to
help distinguish its two conductors. Use this polarity indicator to ensure that
you are connecting the positive (+) terminal on one speaker to the positive (+)
terminal on the other, and the negative (–) to the negative (–).
Figure 3.
Step 2.
Place the receiver module in the desired location in your home near an
AC outlet, as it needs to plug into the wall.
4
Step 3.
When using the WEM-1 to power surround speakers in
a home theater system:
Connect the speaker wire to the push terminals on the receiver module A
and the terminals on the rear of your speakers, as shown in Figure 4. Please
note that the speaker wire features a polarity indicator to help distinguish its
two conductors. Use this polarity indicator to ensure that you are connecting
the positive (+) terminal on one speaker to the positive (+) terminal on the
other, and the negative (–) to the negative (–).
In this application, the output level of your WEM-1 will not only be dependent
on the volume setting of your A/V source; it will also need to be properly
adjusted after installation and before use in order to be able to work correctly
with the other speakers in your multichannel surround system. To adjust the
output level, turn your A/V source on, set your A/V source’s volume control
about a third of the way up, and activate the speaker-level-adjustment test
tone. Make sure that the WEM-1 transmitter and receiver are on, both of the
speakers are connected, and there is RF lock (i.e., the LED on the receiver is
solid green). Using the remote control 1 and 2, adjust the volume level of
the WEM-1 until its output level is balanced with the rest of the speakers in your
surround system. From this point on, you will not be using the WEM-1 remote
control for volume settings. You will be increasing and decreasing the output level
for the entire surround sound system using your A/V source’s volume control.
Please note that the WEM-1 will retain its volume setting when it is in standby,
so there is no need to set its volume level every time the system is turned on.
Right Speaker
Left Speaker
Local Input
The JBL On Air WEM-1 receiver module also includes a local input on the front
of the receiver module. This input allows you to hook up a portable audio player
directly to the WEM-1, wherever you may happen to be. For example, you could
have the system connected to your audio receiver, listening to a local FM station,
and then hook up your portable music player to the local input, switching
between the two different sources.
Figure 4.
Step 4.
To connect a portable audio player to the receiver module, simply connect the
preamp-out, line-out or headphone jack to the line-in on the front of the receiver
module using a 1/8-inch mini-jack – 1/8-inch mini-jack cable (not included).
Plug the transmitter module and receiver module into the wall outlets, using
the correct power supplies and power cords. Make sure the antennas 4E
are extended upward.
To switch between the two sources, push the Input button 3 on the
remote control.
Make sure the ID Code setting on the transmitter 6 is set to the same setting
as that on the receiver B. See the “ID Codes” section for more information
on ID codes. When connected properly, the LED on the front of the receiver
should be red when first plugged in. When a button on the remote is pressed,
the LED should flash green until the transmitter and receiver “lock in.” It will
then light in solid green. This LED will light orange if the local input on the
receiver is selected (see the “Local Input” section for more details).
ID Codes
In the unlikely event that you experience interference when operating the
system, or if you have more than one set of WEM-1 transmitters and receivers
in operation, you may change the channel in which the system operates. On
both the transmitter and receiver modules, there is a four-position ID Code
selector 6B. Simply set each of the selectors to one of the other positions.
The transmitter and receiver must be set to the same position in order for the
system to function correctly. You can also set up a maximum of two receiver
modules to be receiving from the same transmitter by setting the channel
selector on the transmitter and the receiver to the same channel. Please
note that the two receiver modules need to be at least 10' (3m) apart, or
reception and operating range in one or both units may be degraded.
Adjusting the Volume
Depending on the type of connection and the specific source that you are
using, the volume setting on your audio receiver may affect the sound output
level of your WEM-1. To check whether the output from your source is volume-
dependent, turn the volume level on your audio receiver to approximately
halfway. Turn on your WEM-1 transmitter and receiver modules. Once the LED
on the receiver module lights in solid green, indicating that RF lock has been
achieved, verify that there is sound output from the speakers. Then increase
and decrease the volume control on your receiver and observe whether this
affects the sound output from your speakers. If it does not, then the volume
control on your source unit can be set at any position that you may desire,
as it does not affect the performance of the WEM-1. If changing the volume
setting on your source does affect the output from the WEM-1, then you will
need to always keep your source’s volume control at about halfway up with audio
receivers or A/V receivers. From this point on, you will use the remote control
included with the WEM-1 to adjust Volume 1 and 2.
EQ Switch
The WEM-1 offers a choice of EQ positions for use with select JBL speakers.
This circuit optimizes the performance of the system when connected to the
loudspeakers indicated. If your specific loudspeaker is not listed below, simply
set the EQ Switch C to position 1.
EQ Position
Loudspeaker Model
No EQ; use with any loudspeaker not listed below
JBL CSB5
1
2
3
4
5
6
JBL CST55
JBL CS600 satellites
JBL CS400 satellites
™
®
JBL Control NOW, JBL Control Monitor
5
Auto On/Standby
The JBL On Air WEM-1 will automatically enter the Standby mode after
approximately 10 minutes, when no signal is detected from your system. The
WEM-1 will then power on instantly when a signal is detected. When Mute 0
is engaged, auto turn-off is deactivated.
LED Color
Green
Transmitter Module
Receiver Module
Transmitter and receiver module Transmitter and receiver module
are communicating (RF lock) are communicating (RF lock)
Blinking Green Transmitter and receiver are
Transmitter and receiver are
(Slow)
not communicating (no RF lock) not communicating
(no RF lock)
Blinking Green Not applicable
(Fast)
Receiving IR command
from remote control*
Figure 5.
Red
Standby
Standby
Step 2.
(no signal being received)
(no signal being received)
Attach the transmitter module with wall bracket to the wall, using two suitable
screws (and wall anchors, if necessary).
Orange
Not applicable
Local input is selected
Blinking Orange Not applicable
(Slow)
System muted (when local
input is selected)
Wall-Mounting the Receiver Module
Blinking Orange Not applicable
(Fast)
Receiving IR command
from remote control* (when
local input is selected)
CAUTION:
The customer is responsible for proper selection and use of mounting hardware
(available through hardware stores), to properly and safely wall-mount the module.
* Blinking stops when unit reaches minimum or maximum volume setting
Step 1.
Subwoofer Output
Turn receiver module over and remove all four corner screws,
as shown in Figure 6.
The JBL On Air WEM-1 includes a subwoofer output 9 on the receiver module.
This output allows you to feed the low-frequency sounds to a separate powered
subwoofer. A powered subwoofer will deliver deeper bass response than is
possible with speakers alone.
To connect a powered subwoofer to the receiver module, simply connect the
Sub Out 9 on the receiver module to the line-in on the rear of the powered
subwoofer, using a 1/8-inch stereo mini-jack/RCA cable (not included). Please
note that this output is full-range and not filtered or low-passed. Make sure that
your powered subwoofer features a low-pass crossover network and that this
crossover is indeed selected. Do not use the LFE input on a powered subwoofer,
as it is not filtered and you will be hearing a lot of undesirable higher-frequency
information from your subwoofer.
Figure 6.
Step 2.
Attach the wall bracket to the left and right side, as shown in Figure 7.
A Word About Wireless Products
The JBL On Air WEM-1 utilizes advanced wireless transceivers operating in the
2.4GHz frequency band. This is the same frequency band that is used for wireless
home networks and high-quality cordless phones. It also allows the transmission of
high-performance, full-spectrum sound to remote locations, wirelessly.
Step 3.
Reattach the four screws removed in Step 1 through the brackets into the
receiver module, as shown in Figure 7.
Like all wireless devices, the WEM-1 wireless speaker’s operating range may
vary, depending upon variables such as building construction methods and
materials, atmospheric conditions and other sources of interference. Please
information or assistance.
Wall-Mounting
Adjustable wall brackets are included for the transmitter and receiver modules.
The included brackets are for wall-mounting only; they are not to be used for
ceiling-mounting. Ceiling-mounting of the WEM-1 transmitter and/or speakers
is not recommended, regardless of bracket used.
Figure 7.
Step 4.
Attach the receiver module with wall bracket to the wall, using four suitable
screws (and wall anchors, if necessary).
Wall-Mounting the Transmitter Module
Caution
The customer is responsible for proper selection and use of mounting hardware
(available through hardware stores), to properly and safely wall-mount the module.
Step 1.
Insert the two M3 x 4 machine screws through the wall bracket and into the
rear of the transmitter module, as shown in Figure 5.
6
Vertically Stand-Mounting the
Receiver Module
MAINTENANCE AND SERVICE
All wiring connections should be inspected and cleaned or remade periodically.
The frequency of maintenance depends on the metals involved in the connec-
tions, atmospheric conditions and other factors, but once per year is the minimum.
Step 1.
Remove the corner screws located on the left side of the receiver module
when viewed from the bottom, looking at the front, as shown in Figure 8.
In the event that your system ever needs service, contact your local JBL dealer
or distributor, or visit www.jbl.com for a service center near you.
SPECIFICATIONS
Frequency Range:
(+0dB, –1dB)
20Hz – 20kHz
Amplifier Output:
50 Watts per channel
Figure 8.
Signal-to-Noise Ratio:
Operating Range:
80dBA
Step 2.
Up to 70' (22m), depending upon conditions
Rest the receiver module on top of the stand and reattach the two screws that
were removed in Step 1 through the holes in the stand into the bottom of the
receiver module, as shown in Figure 9.
RF Operating Frequency: 2.4GHz
Power Requirement:
Dimensions
100V – 240V AC, 50/60Hz
Transmitter Module:
(H x W x D)
1-1/8" x 6" x 3-7/8" (29mm x 154mm x 98mm)
3-3/4" (95mm) high with antenna extended
Receiver Module:
(H x W x D)
1-1/8" x 6-3/16" x 4-5/8" (29mm x 158mm x 116mm)
3-3/4" (95mm) high with antenna extended
Weight
Transmitter Module:
Receiver Module:
0.6 lb (0.3kg)
0.9 lb (0.4kg)
Figure 9.
Step 3.
Rotate the JBL logo 90˚ by gently pulling it out and turning it.
Features, specifications and appearance are subject to change without notice.
Vertically Mounting the
Transmitter Module
Step 1.
Attach the four included self-adhesive rubber feet in the recesses on the side
of the transmitter module.
Step 2.
Rotate the JBL logo to a vertical orientation.
Remote Control Battery Replacement
CAUTION:
When replacing the lithium battery in the remote, make sure that the
replacement battery is inserted in correct polarity. Place the battery so that
its positive (+) side faces up with the tray held so that the surface with the
dot and/or with a (+) mark next to the part number is facing up.
Declaration of Conformity
Remote control battery installation
We, Harman Consumer Group, Inc.
2, route de Tours
72500 Château du Loir
France
declare in own responsibility that the product described
in this owner’s manual is in compliance with technical
standards:
Pull battery
drawer out.
Insert new battery
with “+” side up, and
slide battery drawer
back into remote.
Push small tab
toward battery slot.
EN 55013:2001+A1:2003
EN 55020:2002+A1:2003
EN 61000-3-2:2000
EN 61000-3-3:1995+A1:2001
EN 60065:2002
CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED.
REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE (CR2025).
WARNING: DO NOT EXPOSE BATTERIES TO EXCESSIVE HEAT SUCH AS
DIRECT SUNLIGHT, FIRE OR THE LIKE.
Laurent Rault
Dispose of dead batteries in accordance with local regulations.
Harman Consumer Group, Inc.
Château du Loir, France 10/08
JBL and Control are trademarks of Harman International Industries, Incorporated, registered in the United States
and/or other countries. JBL Control NOW is a trademark of Harman International Industries, Incorporated.
Harman Consumer Group, Inc., 250 Crossways Park Drive, Woodbury, NY 11797 USA
8500 Balboa Boulevard, Northridge, CA 91329 USA
© 2008 Harman International Industries, Incorporated. All rights reserved.
Part No. 406-000-05960-E 10/08
|