owner’s manual
Thank you for purchasing a JL Audio amplifier for
your automotive sound system.
Your amplifier has been designed and manufactured to exacting
standards in order to ensure years of musical enjoyment in your vehicle.
For maximum performance, we highly recommend that you have
your new amplifier installed by an authorized JL Audio dealer. Your
authorized dealer has the training, expertise and installation equipment
to ensure optimum performance from this product. Should you
decide to install the amplifier yourself, please take the time
to read this manual thoroughly so as to familiarize yourself
with its installation requirements and setup procedures.
If you have any questions regarding the instructions in this
manual or any aspect of your amplifier’s operation, please contact your
authorized JL Audio dealer for assistance. If you need further assistance,
please call the JL Audio Technical Support Department
at (954) 443-1100 during business hours.
ProteCt Your Hearing!
installation aPPliCations
Planning Your installation
We value you as a long-term customer. For
that reason, we urge you to practice restraint in
the operation of this product so as not to damage
your hearing and that of others in your vehicle.
Studies have shown that continuous exposure to
high sound pressure levels can lead to permanent
(irreparable) hearing loss. This and all other
high-power amplifiers are capable of producing
such high sound pressure levels when connected
to a speaker system. Please limit your continuous
exposure to high volume levels.
This amplifier is designed for operation in
vehicles with 12 volt, negative-ground electrical
systems. Use of this product in vehicles with
positive ground and/or voltages other than 12V
may result in damage to the product and will void
the warranty.
This product is not certified or approved for
use in aircraft.
Do not attempt to “bridge” the outputs of this
amplifier with the outputs of a second amplifier,
including an identical one.
It is important that you take the time to read
this manual and that you plan out your
installation carefully. The following are some
considerations that you must take into account
when planning your installation.
Mounting the amplifier upside down is
strongly discouraged.
If mounting the amplifier under a seat,
make sure there is at least 1 inch (2.5 cm) of
space above the amplifier’s outer shell to permit
proper cooling.
Cooling efficiency Considerations:
The outer shell of your JL Audio amplifier
is designed to remove heat from the amplifier
circuitry. For optimum cooling performance,
this outer shell should be exposed to as large a
volume of air as possible. Enclosing the amplifier
in a small, poorly ventilated chamber can
lead to excessive heat build-up and degraded
performance. If an installation calls for an
enclosure around the amplifier, we recommend
that this enclosure be ventilated with the aid
of a fan. In normal applications, fan-cooling
is not necessary.
safety Considerations:
Your amplifier needs to be installed in a dry,
well-ventilated environment and in a manner
which does not interfere with your vehicle’s safety
equipment (air bags, seat belt systems, ABS brake
systems, etc.). You should also take the time to
securely mount the amplifier so that it does not
come loose in the event of a collision or a sudden
jolt to the vehicle.
While driving, operate your audio system in
a manner that still allows you to hear necessary
noises to operate your vehicle safely (horns,
sirens, etc.).
serial number
In the event that your amplifier requires
service or is ever stolen, you will need to have
a record of the product’s serial number. Please
take the time to enter that number in the space
provided below. The serial number can be found
on the bottom panel of the amplifier and on the
amplifier packaging.
stupid mistakes to avoid
Chassis Ground
Connector
(pg. 5)
• Check before drilling any holes in your vehicle
to make sure that you will not be drilling
through a gas tank, brake line, wiring harness or
other vital vehicle system.
Speaker Outputs
(pg. 10)
+12 V Power
Connector
(pg. 5)
Remote Turn-On
Connector
(pg. 6)
• Do not run system wiring outside or underneath
the vehicle. This is an extremely dangerous
practice which can result in severe damage to
your vehicle and person.
Serial Number:
• Protect all system wires from sharp metal
edges and wear by carefully routing them,
tying them down and using grommets and
loom where appropriate.
Input Voltage
Selection
(pg. 7)
Left & Right
Preamp Output Jacks
(pg. 9)
Protection Status
Indicator
Bass EQ
On/Off Switch
(pg. 9)
Filter Mode
Selection
(pg. 7)
(pg. 11)
Jack for
Left & Right
Preamp Input Jacks
(pg. 6)
Power Status
Indicator
(pg. 11)
Remote Bass
Control Knob
(pg. 9)
Input Sensitivity
Control
(pg. 7)
Filter
Frequency Selector
(pg. 7)
• Do not mount the amplifier in the engine
compartment, under the vehicle, on the roof
or in any other area that will expose the
amplifier circuitry to the elements.
2
JL AUDIO G1300
JL AUDIO G1300
3
ProduCt desCriPtion
Power ConneCtions
The JL Audio G1300 is a monoblock,
full-range amplifier utilizing patented Absolute
Symmetry™ Class A/B technology.
The G1300 can be operated with a wide variety
of source units and system configurations.
6) Find a good, solid metal grounding point
close to the amplifier and connect the
negative power wire to it using appropriate
hardware (use of the JL Audio ECS master
ground lug, XB-MGLU is recommended).
Use the same size power wire as the wire
connected to the “+12VDC” connection
(minimum 8 AWG), no longer than 36 inches
(90 cm) from the amplifier to the ground
connection point. In some vehicles, it may be
necessary to upgrade the battery ground wire.
(See page 5 for important notice).
Before installing the amplifier, disconnect the
negative (ground) wire from the vehicle’s battery.
This will prevent accidental damage to the system,
the vehicle and your body during installation.
The ground connection should be made using
the same gauge wire as the power connection
and should be kept as short as possible, while
accessing a solid piece of sheet metal in the
vehicle. The surface of the sheet metal should
be sanded at the contact point to create a clean,
metal-to-metal connection between the chassis
and the termination of the ground wire. For
optimal grounding, we recommend the use of a
JL Audio ECS master ground lug (XB-MGLU).
Alternatively, a sheet metal screw or bolt can be
used with a star washer.
Any wires run through metal barriers (such
as firewalls), must be protected with a high
quality rubber grommet to prevent damage to the
insulation of the wire. Failure to do so may result
in a dangerous short circuit.
tYPiCal installation sequenCe
The following represents the sequence
for a typical amplifier installation, using an
aftermarket source unit or OEM Interface
processor (like the CleanSweep CL441dsp).
Additional steps and different procedures may
be required in some applications. If you have
any questions, please contact your authorized
JL Audio dealer for assistance.
7) Securely mount the amplifier.
8) Connect the positive and negative power
wires to the amplifier. A fuse near the
amplifier is not necessary.
9) Connect the remote turn-on wire
to the amplifier.
1) Disconnect the negative battery post
connection and secure the disconnected cable
to prevent accidental re-connection during
installation. This step is not optional.
2) Run power wire (minimum 8 AWG) from the
battery location to the amplifier mounting
location, taking care to route it in such a
way that it will not be damaged and will not
interfere with vehicle operation. Use 4 AWG
or larger power wire and a power distribution
block if additional amplifiers are being
installed with the G1300.
3) Connect power wire to the positive battery
post. Fuse the wire with an appropriate fuse
block (and connectors) within 18 inches (45
cm) wire length of the positive battery post.
This fuse is essential to protect the vehicle.
Do not install the fuse until the power wire
has been securely connected to the amplifier.
4) Run signal cables and remote turn-on wire
from the source unit to the final amplifier
mounting location.
The G1300’s “+12VDC” and “Ground”
connections are designed to accept 8 AWG -
4 AWG power wire. 8 AWG is a minimum power
wire size for this amplifier.
If you are installing the G1300 with other
amplifiers and wish to use a single main power
wire, use 4 AWG or larger main power wire
(depending on the overall current demands of all
the amplifiers in the system). This 4 AWG or
larger power wire should terminate into a
distribution block mounted as close to the
amplifiers as possible and should connect to the
G1300 with 8 AWG - 4 AWG power wire.
10) Connect the input cables to the amplifier.
11) Connect the speaker cables to the amplifier.
12) Carefully review the amplifier’s control
settings to make sure that they are set
according to the needs of the system.
13) Install the power wire fuse (30A for a
single G1300) and reconnect the negative
battery post terminal.
14) Turn on the source unit at a low level
to double-check that the amplifier is
configured correctly. Resist the temptation
to crank it up until you have verified the
control settings.
15) Make necessary adjustments to the input
sensitivity controls to obtain the right
overall output and the desired balance
in the system. See Appendix A (page 12)
for the recommended input sensitivity
setting method.
Many vehicles employ small (10 AWG -
6 AWG) wire to ground the battery to the
vehicle chassis and to connect the alternator’s
positive connection to the battery. To prevent
voltage drops, these wires should be upgraded
to 4 AWG when installing amplifier systems
with main fuse ratings above 60A.
Fuse requirements
It is absolutely vital that the main power
wire(s) to the amplifier(s) in the system be
fused within 18 inches (45 cm) of the positive
battery post connection. The fuse value at each
power wire should be high enough for all of the
equipment being run from that power wire.
If only the G1300 is being run from that power
wire, we recommend a 30A fuse be used.
AFS (small blade fuse), AGU (big glass fuse)
or MaxiFuse™ (big plastic-body fuse) types are
recommended.
Note: Smaller AWG numbers mean bigger wire
and vice-versa (1/0 AWG is the largest, 2 AWG is
smaller, then 4 AWG, then 8 AWG, etc.).
To connect the power wires to the amplifier,
first back out the set screw on the top of the
terminal block, using the supplied 2.5 mm hex
wrench. Strip 1/2 inch (12 mm) of insulation from
the end of each wire and insert the bare wire into
the terminal block, seating it firmly so that no
bare wire is exposed. While holding the wire in
place, tighten the set screw firmly, taking care not
to strip the head of the screw.
16) Enjoy the fruits of your labor with your
favorite music.
5) Run speaker cables from the speaker systems
to the amplifier mounting location.
No fuse is required or recommended directly
before the amplifier power connection. If one is
desired, we recommend the use of a 30A AGU,
AFS or MaxiFuse™ type.
4
JL AUDIO G1300
JL AUDIO G1300
5
turn-on lead
inPut seCtion
inPut Voltage range:
amPliFier Controls
The G1300 uses a conventional +12V remote
turn-on lead, typically controlled by the source
unit’s remote turn-on output. The amplifier will
turn on when +12V is present at its “Remote”
input and turn off when +12V is switched off. If
a source unit does not have a dedicated remote
turn-on output, the amplifier’s turn-on lead can
be connected to +12V via a switch that derives
power from an ignition-switched circuit.
The G1300’s “Remote” turn-on connector is
designed to accept 18 AWG – 12 AWG wire. To
connect the remote turn-on wire to the amplifier,
first back out the set screw on the top of the
terminal block, using the supplied 2.5 mm hex
wrench. Strip 1/2 inch (12mm) of wire and insert
the bare wire into the terminal block, seating it
firmly so that no bare wire is exposed. While
holding the wire in the terminal, tighten the set
screw firmly, taking care not to strip the head of
the screw and making sure that the wire is firmly
gripped by the set screw.
The G1300’s input section allows you to send
signal to the amplifier section through the use
of two differential-balanced inputs, one for the
left channel signal and one for the right channel
signal. Connection is via RCA-type jacks.
A wide range of signal input voltages can be
accommodated by the G1300’s input section
(200mV – 8V). This wide range is split up into
two sub-ranges, accessible via a switch located to
the left of the Input Connectors.
The “Low” position on the “Input Voltage”
switch selects an input sensitivity range between
200mV and 2V. This means that the “Input
Sens.” rotary control will operate within that
voltage window. If you are using an aftermarket
source unit or an OEM interface processor with
conventional preamp-level outputs, this is most
likely the position that you will use.
The “High” position on the “Input Voltage”
switch selects an input sensitivity range between
800mV and 8V. This is useful for certain high-
output preamp level signals as well as speaker-level
output from source units and small amplifiers.
To use speaker-level sources, splice the speaker
output wires of the source unit or small amplifier
onto a pair of RCA plugs. No line output
converter is needed in most cases.
1) “Input Sens.”: Once the appropriate “Input
Voltage” range has been selected, the control
labeled “Input Sens.” located in the “Amplifier
Controls” section can be used to match the
source unit’s output voltage to the input
stage of the amplifier for maximum clean
output. Rotating the control clockwise will
result in higher sensitivity (louder for a given
input voltage). Rotating the control counter-
clockwise will result in lower sensitivity
(quieter for a given input voltage.)
You may run a stereo or a mono signal into
the inputs of the amplifier. The amplifier’s input
section automatically sums stereo signals to mono
for the internal amplifier section.
The amplifier will operate with only one input
connection (left or right), but will require an
increase in input sensitivity to overcome the loss
of signal. If a mono input signal is to be run, we
recommend that you use a “Y-adaptor” to split the
mono signal into both inputs of the amplifier.
To properly set the amplifier for maximum
clean output, please refer to Appendix A (page
12). After using this procedure, you can then
adjust the “Input Sens.” level downward if this is
required to achieve the desired system balance.
The output of the amplifier will decrease for
a given input voltage when the “Input Range”
switch is placed in the “High” position.
Conversely, the output will be higher with the
switch in the “Low” position. While this may
sound counter-intuitive, it is consistent with
the descriptions above.
Left Channel Only or Right Channel Only
Information: If you wish to send a Left-only or
Right-only signal to the G1300, use a “Y-Adaptor”
to split the single channel signal into both left
and right RCA inputs. This option is useful
when using one G1300 to drive the left channel
speakers only and another G1300 to drive right
channel speakers only.
Do not increase any “Input Sens.” setting
for any channel(s) of any amplifier in the
system beyond the maximum level established
during the procedure outlined in Appendix
A (page 12). Doing so will result in audible
distortion and possible speaker damage.
If you plan to use the “Pre-Outs” to feed
a stereo amplifier, you must connect a
stereo signal to the input of the amplifier.
A mono signal into the amplifier will result
in a mono signal out of the preamp output.
(It’s a great amplifier, but it doesn't do magic).
6
JL AUDIO G1300
JL AUDIO G1300
7
bass boost Controls
Pre-outs
Filter Controls
2) “Filter Mode” Control: The G1300 employs
a 12dB per octave filter. This filter can be
configured into one of two filter types or
defeated completely by way of the three-
position “Filter Mode” switch:
“Off”: Defeats the filter completely, allowing
the full range of frequencies present at the inputs
to feed the amplifier. This is useful for systems
utilizing outboard crossovers or requiring full-
range reproduction from the G1300.
“LP” (Low-Pass): Configures the filter to
attenuate frequencies above the selected filter
frequency at a rate of 12dB per octave. Useful
for connection of subwoofer(s) to the G1300 in
a bi-amplified system.
“HP” (High-Pass): Configures the filter to
attenuate frequencies below the selected filter
frequency at a rate of 12dB per octave. Useful
for connection of a coaxial or component
satellite speaker system to the G1300 in a
bi-amplified system.
The G1300’s “Pre-Outs” connectors output
unprocessed (pass-through) left and right channel
preamp level signals, permitting connection of
additional amplifiers in a system.
Most speakers are not designed to reproduce
the full range of frequencies audible by the
human ear. For this reason, most speaker
systems are comprised of multiple speakers, each
dedicated to reproducing a specific frequency
range. Filters are used to select which frequency
range is sent to each section of a speaker system.
The division of frequency ranges to different
speakers can be done with passive filters (coils
and/or capacitors between the amplifier outputs
and the speakers), which are acceptable and
commonly used for filtering between mid-
range speakers and tweeters. Filtering between
subwoofer systems and satellite speaker systems
is best done with active filters, which cut off
frequency content at the input to the amplifier.
Active filters are more stable than passive filters
and do not introduce extraneous resistance,
which can degrade subwoofer performance.
The active filter built into the G1300 can be
used to eliminate potentially harmful and/or
undesired frequencies from making their way
through the amplifier section to the speaker(s).
This serves to improve tonal balance and to avoid
distortion and possible speaker failure. Correct
use of this filter can substantially increase the
longevity and fidelity of your audio system.
1) “Bass Boost”: This switch allows the user
to activate a 6 dB boost centered at 48 Hz.
The “Filter Mode” switch in the “Amplifier
Controls” section must be in the “LP” position
for the bass boost to be functional.
The preamp output signals are identical to
the input signals and are not affected by any
settings in the “Amplifier Controls” or “Bass
Boost Controls” sections. The signal level of
the “Preamp Output” is line-level (low voltage),
regardless of the position selected via the G1300’s
“Input Voltage” switch. An additional amplifier
connected to these preamp outputs should have
its input voltage switch set to the “Low“ position.
2) “Remote Bass Port”: This port allows you to
connect an optional remote boost knob (sold
separately, JL Audio Model RBC-1) that can
be mounted in the front of the vehicle. With
the RBC-1 connected, the boost is no longer
limited to 0 or +6 dB, allowing a range of
0 - 12 dB of boost to be selected.
3) “Filter Freq. (Hz)” The filter frequency
markings surrounding this rotary control
are for reference purposes and are generally
accurate to within 1/3 octave or better. If you
would like to select the filter cutoff frequency
with a higher level of precision, consult the
chart in Appendix B (page 13).
Tuning Hint: If you are using the G1300 to drive
a subwoofer system (“LP” mode) or a component
satellite speaker system (“HP” mode), 80 Hz is a
good baseline “Filter Freq. (Hz)” setting. After
properly adjusting the “Input Sens.”, as outlined
in Appendix A (page 12), you can fine tune the
“Filter Freq. (Hz)” control to achieve the desired
system frequency response.
8
JL AUDIO G1300
JL AUDIO G1300
9
sPeaker outPuts
The G1300’s speaker outputs are designed to
accept 8 AWG - 16 AWG wire.
amPliFier status indiCator ligHts &
ProteCtion CirCuitrY
There are two status indicator lights on the
input / control end of the amplifier.
Do not attempt to “bridge” the outputs of this
amplifier with the outputs of a second amplifier,
including an identical one.
low-Voltage protection:
If the car’s supply voltage drops below 10
volts, the entire amplifier will shut itself off to
protect its internal circuitry. The green “Power”
indicator will turn off when this occurs. The
amplifier will turn back on when voltage climbs
back above 10 volts. This may happen in a rapid
cycle when bass-heavy program material causes
a weak charging system to dip below 10 volts
momentarily. If this is happening in your system,
turn your audio system off and have your power
wiring, ground connections and charging
system inspected.
The G1300 is designed to deliver power into
speaker loads equal to or greater than 2 ohms.
To connect the speaker wires to the amplifier,
first back out the set screws own the top of the
terminal block, using the supplied 2.5 mm hex
wrench. Strip 1/2 inch (12 mm) of insulation from
the end of each wire and insert the bare wire into
the terminal block, seating it firmly so that no
bare wire is exposed. While holding the wire in
place, tighten the set screw firmly, taking care not
to strip the head of the screw.
serViCing Your Jl audio amPliFier
If your amplifier fails or malfunctions, please
return it to your authorized JL Audio dealer so
that it may be sent in to JL Audio for service.
There are no user serviceable parts or fuses inside
the amplifier. The unique nature of the circuitry
in the JL Audio amplifiers requires specifically
trained service personnel. Do not attempt
to service the amplifier yourself or through
unauthorized repair facilities. This will not only
void the warranty, but may result in the creation
of more problems within the amplifier.
1) “Power” (Green): lights to indicate that the
amplifier is turned on and operating normally.
2) “Protect” (Red): Indicates that the amplifier
protection circuitry has been activated to
prevent product failure due to a short-circuit
or a dangerously low impedance connected
to the amplifier output(s). Connecting the
speaker outputs to an impedance lower than
2 ohms stereo (4 ohms bridged) will cause
this protection mode to activate. When this
protection mode is activated, the amplifier will
reduce it maximum power output to protect its
circuitry, which will manifest itself as increased
distortion. When the problem is corrected, the
amplifier will return to normal operation.
Speaker loads below 2 ohms nominal are not
recommended and may cause the amplifier
to initiate a protection mode which reduces
power output.
If you have any questions about the installation or
setup of the amplifier not covered in this manual,
please contact your dealer or technical support.
You will notice that there are two “+” positive
connections and two “–” negative connections.
This is to facilitate multiple speaker wiring.
The two positive and two negative connections
are connected in parallel inside the amplifier.
Connecting two speakers, each to one set of
positive and negative terminals, will result in a
parallel speaker connection. If only connecting
one pair of speaker wires, it is not necessary to
use both sets of connections.
advanced rollback thermal protection
Unlike conventional thermal protection
systems, which shut down an amplifier when it
overheats, this system protects the amplifier by
gradually reducing power output if the amplifier’s
safe operating temperature is exceeded. The
amplifier will continue to operate and return
to normal power output once its temperature
returns to a normal range.
Jl audio technical support:
(954) 443-1100
9:00 AM – 5:30 PM (Eastern Time Zone)
Monday - Friday
10
JL AUDIO G1300
JL AUDIO G1300
11
aPPendix a:
aPPendix b:
aPPendix C:
input sensitivity level setting
8) Increase the “Input Sens.” control until the
target voltage is observed with the voltmeter.
9) Once you have adjusted the G1300 to its
maximum low-distortion output level,
reconnect the speaker(s). The “Input Sens.”
controls can now be adjusted downward if the
amplifier requires attenuation to achieve the
desired system balance.
Precise Frequency Selection Chart
g1300 specifications
Following the directions below will allow the
installer to adjust the input sensitivity of each
amplifier channel pair simply and easily in just a
few minutes using equipment which is commonly
available in installation bays.
“Filter Freq” amP Filter
general specifications:
Recommended Fuse Value: 30A
detent
number
Panel
marking
actual
Freq.
Recommended Fuse Type: AGU, AFS or MaxiFuse™
Full counter-clockwise: 53
01 . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
02 . . . . . . . . . . . “50” . . . . . . . . . . . .53
03 . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
04 . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
05 . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
06 . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
07 . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
08 . . . . . . . . . . . “55” . . . . . . . . . . . .56
09 . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
10 . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
11 . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
12 . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
13 . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
14 . . . . . . . . . . . “60” . . . . . . . . . . . .65
15 . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
16 . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
17 . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
18 . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
19 . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
20 . . . . . . . . . . . “80” . . . . . . . . . . . .81
21 . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
22 . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
23 . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
24 . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
25 . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
26 . . . . . . . . . . “120” . . . . . . . . . . 115
27 . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
28 . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
29 . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
30 . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
31 . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
32 . . . . . . . . . . “150” . . . . . . . . . . 177
33 . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
34 . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
35 . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
36 . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
37 . . . . . . . . . . . . . . . . . . . . . . . . . . . 216
38 . . . . . . . . . . “200” . . . . . . . . . . 218
39 . . . . . . . . . . . . . . . . . . . . . . . . . . . 225
Full-clockwise: 225
input sections:
No. of Inputs: One Stereo Pair
necessary equipment
• Digital AC Voltmeter
Input Type: Differential-balanced with RCA jack inputs
Input Range: Switchable from 200mV - 2V RMS to
800mV - 8V RMS
• CD with a sine-wave test tone recorded at
0 dB reference level in the frequency range
to be amplified for that set of channels
(50 Hz for subwoofer channels, 1 kHz for a
midrange application). Do not use attenuated
test tones (-10 dB, -20 dB, etc.).
Do not increase any “Input Sens.” setting for
any amplifier channel or channel pair in the
system beyond the maximum level established
during this procedure. Doing so will result in
audible distortion and possible speaker damage.
amplifier section:
Amplifier Topology: Class A/B with patented Absolute
Symmetry™ dual N-Channel MOSFET output design
Power Supply: Unregulated MOSFET switching type
Rated Power @ 14.4V with less than
the nine-step Procedure
1) Disconnect the speaker(s) from the
It will be necessary to re-adjust the
“Input Sens.” for the affected channels if any
equalizer boost is activated after setting the
“Input Sens.” with this procedure. This applies
to any EQ boost circuit, including source unit
tone controls or EQ circuits. EQ cuts will not
require re-adjustment.
1% THD + Noise (20Hz - 20 kHz):
amplifier’s speaker output connectors.
2) Turn off all processing (bass/treble, loudness,
EQ, etc.) on the source unit, processors (if
used) and amplifier. Set fader control to center
position and subwoofer level control to 3/4 of
maximum (if used to feed the G1300).
3) Switch the “Input Voltage” switch to “Low”
and turn the “Input Sens.” control all the
way down.
4) Set the source unit volume to 3/4 of full
volume. This will allow for reasonable gain
overlap with moderate clipping at full volume.
5) Using the chart on this page, determine the target
voltage for input sensitivity adjustment according
to the nominal impedance of the speaker system
connected to the amplifier outputs.
6) Verify that you have disconnected the speakers
before proceeding. Play a track with an
appropriate sine wave (within the frequency
range to be amplified by the G1300) at 3/4
source unit volume.
7) Connect the AC voltmeter to the speaker output
connectors of the amplifier. Make sure you test
the voltage at the correct connectors (+ and –).
150W RMS x 1 @ 4 ohms, 300W RMS x 1 @ 2 ohms
Rated Power at 12.5V with less than
1%THD+Noise (20Hz - 2 kHz):
120W RMS x 1 @ 4 ohms, 220W RMS x 1 @ 2 ohms
Signal to Noise Ratio: >104 dB referred to rated power
(A-weighted, 20 Hz-20 kHz noise bandwidth)
Frequency Response: 10 Hz - 25 kHz (+0, -1dB)
Damping Factor: >200 @ 4 ohms/50 Hz,
>100 @ 2 ohms/50 Hz
nom. impedance
target aC Voltage
24.5 V
Slew Rate: 22V/µs
4Ω
3Ω
2Ω
24.5 V
amplifier Filter:
24.5 V
Filter Type: State-variable, 12dB/octave Butterworth with
continuously variable cutoff frequency selection from
50-200 Hz. Configurable as Low-Pass or High-Pass.
Defeatable.
Preamp output:
Buffered pass-through type.
dimensions(lxwxH):
9.8" x 9.25" x 2.50" (250mm x 235mm x 63.5mm)
Due to ongoing product development, all specifications are subject to
change without notice.
12
JL AUDIO G1300
JL AUDIO G1300
13
aPPendix d: troublesHooting
“How do i properly set the input sensitivity on my amplifier”
Please refer to Appendix A (page 12) to set the input sensitivity for
“my amplifier shuts off once in a while, usually at higher volumes”
Check your voltage source and grounding point. The power supply
maximum, low-distortion output.
“my amplifier doesn’t turn on”
of the G1300 will operate with charging system voltages
down to 10V. Shutdown problems at higher volume levels
can occur when the charging system voltage drops below
10V. These dips can be of very short duration making them
extremely difficult to detect with a common DC voltmeter.
To ensure proper voltage, inspect all wiring and termination
points. It may also be necessary to upgrade the ground
wire connecting the battery to the vehicle’s chassis and the
power wire connecting the alternator to the battery. Many
vehicles employ small (10 AWG - 6 AWG) wire to ground the
battery to the vehicle’s chassis and to connect the alternator to
the battery. To prevent voltage drops, these wires should be
upgraded to 4 AWG when installing amplifier systems with
main fuse ratings above 60A. Grounding problems are the
leading cause of misdiagnosed amplifier “failures.”
Check the fuse, not just visually, but with a continuity meter. It is
possible for a fuse to have poor internal connections that
cannot be found by visual inspection. It is best to take the
fuse out of the holder for testing. If no problem is found with
the fuse, inspect the fuse-holder.
Check the integrity of the connections made to each of the
“+12VDC”, “Ground”, and “Remote” terminals. Ensure
that no wire insulation is pinched by the terminal set screw
and that each connection is tight.
Check to make sure there is +12V at the “Remote” connection of the
amplifier. In some cases, the turn-on lead from the source unit
is insufficient to turn on multiple devices and the use of a relay
is required. To test for this problem, jump the “+12VDC” wire
to the “Remote” terminal to see if the amplifier turns on. If this
does not work, proceed to the next step.
“my amplifier turns on, but there is no output”
“i get a distorted / attenuated sound coming out of the speaker(s)”
Check the speaker wires for a possible short, either between the
Check the input signal using an AC voltmeter to measure the
voltage from the source unit while an appropriate test tone is
played through the source unit (disconnect the input cables
from the amplifier prior to this test). The frequency used
should be in the range that is to be amplified by the amplifier
(example: 50 Hz for a sub bass application or 1 kHz for a full
range / high-pass application). A steady, sufficient voltage
(between 0.2 and 8.0-volts) should be present at the output of
the signal cables.
Check the output of the amplifier. Using the procedure explained in
the previous check item (after plugging the input cables back
into the amplifier) test for output at the speaker outputs of
the amplifier. Unless you enjoy test tones at high levels, it is
a good idea to remove the speaker wires from the amplifier
while doing this. Turn the volume up approximately half
way. 5V or more should be measured at the speaker outputs.
This output level can vary greatly between amplifiers but it
should not be in the millivolt range with the source unit at
half volume. If you are reading sufficient voltage, check your
speaker connections as explained below.
positive and negative leads or between either speaker lead
and the vehicle’s chassis ground. If a short is present, you
will experience distorted and/or attenuated output. The
“Protect” light will illuminate in this situation. It may be
helpful to disconnect the speaker wires from the amplifier
and use a different set of wires connected to a test speaker.
Check the nominal load impedance to verify that of the amplifier is
driving a load equal to or greater than 2 ohms.
Check the input signal and input signal cables to make sure signal
is present at the “Amplifier Inputs” and the cables are not
pinched or loose. It may be helpful to try a different set of
cables and/or a different signal source to be sure.
“my amplifier’s output fluctuates when i tap on it or hit a bump”
Check the connections to the amplifier. Make sure that the
insulation for all wires has been stripped back far enough to
allow a good contact area inside the terminal block.
Check the input connectors to ensure that they all are making good
contact with the input jacks on the amplifier.
Check to ensure that the speaker wires are making a good
connection with the metal inside the terminal block. The
speaker wire connectors are designed to accept up to 8 AWG
wire. Make sure to strip the wire to allow for a sufficient
connection with the metal inside the terminal block.
14
JL AUDIO G1300
JL AUDIO G1300
15
installation notes:
Use this diagram to document your amplifier’s switch and control positions.
16
JL AUDIO G1300
JL AUDIO G1300
17
installation notes:
installation notes:
18
JL AUDIO G1300
JL AUDIO G1300
19
|