JVC Computer Drive MC D207U User Manual

DVD-ROM DRIVE  
INSTRUCTIONS  
MC-D207U  
For Customer Use:  
Enter below the Model No. and Serial  
No. which are located at the top of the  
unit. Retain this information for future  
reference.  
Model No. MC-D207U  
Serial No.  
This instruction manual has been manufactured from 100% recycled paper.  
LST0038-001B  
 
This unit is a DVD-ROM drive with a 7x speed capability. It especially designed for the JVC CD-ROM Library or CD/DVD  
Library. It is not compatible with the MC-7000 series “DVD-RAM Library”.  
The MC-D207U cannot be operated separately.  
A DVD videodisk playback is not possible with the MC-D207U.  
ROM Replacement  
When this drive is mounted in the MC-1200U/1600U or MC-2200U/2600U CD-ROM Library, certain serial numbers may  
require to replace the ROM.  
Read the section “ROM REPLACEMENT IN THE CD-ROM LIBRARY” on page 6 for the first time.  
ACCESSORIES AND DOCUMENTATION  
Accessories  
Drive locking screw (M3 with washer) ......................... 2 (including one spare)  
Documentation  
Instructions .............................................................. 1  
INSTALLATION  
Please refer to the instruction manual of your Library for more information about the CD-ROM or CD/DVD Library.  
Drive locking section  
1. How to Open the Door of the JVC Library  
In order to open the door, please also refer to the section  
Drive locking screw  
mounting hole  
“HOWTO OPENTHE DOOR DURING OPERATIONin the in-  
structions for the JVC CD-ROM or CD/DVD Library.  
1. Select the [DOOR OPEN MODE] on the MENU screen of the  
• Figure shows the MC-1200U/E  
LCD display section.  
2. Press and hold the “SELECT” switch for five seconds.  
Drive locking section  
3. Turn off the power of the JVC Library when the [YOU MAY OPEN  
THE DOOR] or [THE DOOR CAN BE OPENED] message is  
displayed on the LCD display section.  
Drive locking screw  
mounting hole  
4. Insert the key in the key cylinder located at the center of the  
door and turn it 90 degrees counterclockwise to unlock and open  
the door.  
• Figure shows the MC-2200U  
or MC-8200U  
Drive locking screw  
mounting hole  
Before you start installing the DVD-ROM Drive, be sure to  
turn off the power of the host computer, all peripheral de-  
vices and the Library.  
Drive locking section  
• Figure shows the MC-2100U  
or MC-8100U  
3
 
INSTALLATION  
2. How to Open the Drive Storage Cover  
Drive No.6  
Drive No.5  
Drive No.4  
Drive No.3  
Drive No.2  
Drive No.1  
Figure shows the MC-2200U  
or MC-8200U  
Please also refer to the corresponding sections in the  
Drive storage  
section  
Library instructions.  
1. Remove the screws from the drive section cover,  
which is located at the rear of the Library.  
2. Remove the drive storage cover.  
Drive storage cover  
Screws  
Figure shows the MC-2100U  
or MC-8100U  
Drive No.4  
Drive No.3  
Drive No.2  
Drive No.1  
Drive storage  
section  
Drive storage  
section  
Drive No.6  
Drive storage  
section  
Drive No.5  
Drive No.4  
Screws  
Screws  
Drive storage  
cover  
Drive No.3  
Drive No.2  
Drive No.1  
Screws  
To be reused when  
refitting the cover later.  
Drive storage  
cover  
Figure shows the MC-1200U/E  
3. How to Determine the Installation Position of the DVD-ROM Drive  
1. Install drive from the No.1 to No.6 slot in that order without skipping.  
Starting installation from the lowest No.1 slot will simplify future installation work.  
Drive storage section  
4. How to Install the DVD-ROM Drive  
Sensor slit  
•Beware of damage  
1. Insert the drive from the rear of the JVC CD-ROM or CD/DVD Library.  
Pay attention not to damage the sensor slit.  
Always insert the DVD-ROM Drive correctly.  
Check that cables connected on the rear of the unit are not caught  
or pinched when inserting the DVD-ROM Drive.  
2. Insert the DVD-ROM Drive slowly until the screw installation hole  
located on the side of the DVD-ROM Drive and the screw installation  
hole located on the drive locking section are aligned.  
3. Lock the DVD-ROM Drive in place by using the drive locking screw  
on the door panel side of the drive.  
Drive locking section  
Tighten the screw firmly.  
If the drive locking screw is loose, the drive and/or CD-ROM, CD/  
DVD Library could suffer damage.  
Drive locking  
screw  
4
 
INSTALLATION  
5. How To Connect Cables To The DVD-ROM Drive  
1. Connect the power supply cable, control cable and SCSI cable to the connectors at the rear of the DVD-ROM Drive.  
Connect to the drive the power supply cable and control cable which extend from the side of the DVD-ROM drive  
installation slot.  
With the MC-2100U and the MC-8100U models be sure to connect a control cable with the same component No., as  
the drive bay No., otherwise proper operation may not be possible.  
Insert all connectors firmly.  
Rear section of the DVD-ROM Drive  
Control cable  
Dip switches  
14p  
W
N
Slide switch  
4p  
Power supply cable  
SCSI cable  
Connection example of a SCSI cable  
Internal SCSI ribbon cable  
Up to six drives can be connected normally.  
(But only four drives in the case of the MC-2100U  
and the MC-8100U)  
(Terminate here)  
DVD-ROM Drive  
DVD-ROM Drive  
DVD-ROM Drive  
Library SCSI board  
SCSI connector  
OUT 2  
IN  
OUT 1  
IN  
2
Connect an active terminator.  
1
To be connected with host  
computer's SCSI host adapter  
SCSI cables should be connected as a daisy chain connection. Each connector may be connected to the drive  
positions as illustrated in the diagram.  
Terminate the physical end of the SCSI bus. To use the built-in drive terminator, read 6 -1.  
It is recommended to use an external terminator to improve the stability of the SCSI bus communications.  
6. How To Set The Dip and Slide Switches  
Always turn OFF the power of Library when you set the dip switch modes.  
DIP switch  
Slide switch  
W
N
1
2
3
4
ON  
(Factory setting)  
OFF  
1. TERM : This selects the use of the built-in terminator.  
To use the built-in drive terminator, set the TERM of the drive to ON and the TERM of other drives to OFF.  
When not using the built-in terminator, attach an active SCSI terminator to the OUT side of the SCSI connector.  
In this case, set the TERM of all built-in drives to OFF.  
5
 
INSTALLATION  
2. ID2 - ID0 : This sets the SCSI ID No. on the drives.  
Switch  
ID1  
SCSI ID  
No.  
Remarks  
ID2  
OFF  
OFF  
OFF  
OFF  
ON  
ID0  
OFF  
ON  
0
1
2
3
4
5
6
7
OFF  
OFF  
ON  
Default factory setting  
OFF  
ON  
ON  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
Set the SCSI ID No. between 0 - 7 using only an ID No. that is not being used by other SCSI devices.  
For the details on default factory settings, please refer to the section SCSI ID No. SETTINGof the instructions for the  
JVC CD-ROM or CD/DVD Library.  
3. Set the slide switch.  
Be sure to set the slide switch to N for use. (The position W is provided for service use only.)  
7. How To Refit The Drive Storage Cover  
Always refit the drive storage cover before switching ON the JVC CD-ROM or CD/DVD Library.  
1. Fasten the cover with the screws that were removed in the procedure ( 2 -1).  
8. How To Close And Lock The Door Of The JVC CD-ROM or CD/DVD Library  
Always close and lock the door before switching ON the JVC CD-ROM or CD/DVD Library.  
1. Close the door and lock the key cylinder.  
2. Turn the power switch ON.  
Before you add, remove or replace drives, and/or change the SCSI ID No., turn OFF the power of the host computer.  
Remember to turn it ON again after completing the necessary operations.  
9. Automatic Drive Detection Mode  
Please also refer to the corresponding sections in the CD/DVD Library instructions.  
If using the CD/DVD Library MC-8100U/8200U/8600U, be sure to execute the auto drive detection mode after  
installing, adding, exchanging or removing drives, to prevent any malfunction.  
1. While holding the 8key on the control panel, turn on the power of the Library.  
2. When the LCD display shows DRIVE DETECTION COMPLETED, turn off the power of the Library.  
3. Turn the Library on again.  
6
 
ROM REPLACEMENT IN THE CD-ROM LIBRARY  
If the DVD-ROM drive is being mounted in a MC-2200U/2200PU/2600U/2600PU or MC-1200U/1600U CD-ROM Library and  
does not meet the following conditions, the ROM is required to be replaced in the Library.  
Please consult your dealer or nearest JVC-authorized service agent for ROM replacement.  
The library already has a MC-D207U mounted within the unit.  
The library already has a MC-D104U or a MC-R18U drive mounted within the unit.  
The library is a MC-2200U/2200PU/2600U/2600PU CD-ROM Library and has the last four digits of the serial number as  
follows.  
MC-2200U: 0092 or after. MC-2200PU: 0081 or after. MC-2600U: 0387 or after. MC-2600PU: 0061 or after.  
For the ROM replacement method, please consult your dealer or nearest JVC-authorized service agent.  
SPECIFICATIONS  
Applicable discs  
(Playback only)  
: CD, CD-ROM Mode-1, CD-ROM Mode-2 (XA, CD-I, Photo-CD, Video CD) and CD-R/RW written in accord-  
ance withYELLOW BOOK, RED BOOK, GREEN BOOK and ORANGE BOOK regulations may be applicable.  
DVD-ROM (Single layer: 4.7 GB/single-sided, double layer: 8.5 GB/single-sided)  
DVD-R (4.7 GB or 3.95 GB, disc at once)  
DVD-RAM (Ver. 2.1: single-sided 4.7 GB or double-sided 9.4 GB)  
DVD-RAM (Ver. 1.0: single-sided 2.6 GB)  
* Note 1: The following formatted media may not perform satisfactorily depending on the write conditions:  
CD-R, CD-RW, DVD-R and DVD-RAM.  
* Note 2: In order to prevent problems when using the DVD-RAM, a system that has the two features de-  
scribed below should be adopted. Please inquire about details for establishing this system at your  
dealer or the nearest JVC-authorized service agent.  
The feature that allows the disc to be re-loaded to the disc-drive a second time. The machine  
may recognize a disc after having failed to recognize it at the first loading.  
The feature that permits the timeout period for disc recognition to be set.  
* Note 3: Only the discs with a diameter of 120 mm are applicable.  
Interface  
: SCSI-2  
Data transfer speed  
: Sustained (When the host adapter is set to the maximum sync transfer rate of 20 Mbytes/s)  
CD-ROM:  
Approx. 6 Mbytes/s max. (40X max., CAV)  
DVD-ROM (Single layer):  
Approx. 10 Mbytes/s max. (7X max., CAV)  
DVD-ROM (Double Layer):  
Approx. 10 Mbytes/s max. (7X max., CAV)  
DVD-R (3.95 GB or 4.7 GB):  
Appr ox. 3.46 Mbytes/s max. (2.3X max., CAV)  
DVD-RAM (Single-sided 4.7 GB, single-sided 2.6 GB):  
Approx. 2.77 Mbytes/s typ. (2X max., CAV)  
Burst  
05 Mbytes/s (asynchronous)  
10 Mbytes/s (synchronous)  
Average access time  
(1/3 stroke, typ)  
: DVD-ROM 135 ms  
CD-ROM  
125 ms  
The above values were measured using JVCs measurement method.  
Buffer capacity  
: 512 kbytes  
Operating environment  
: Temperature 5 °C to 35 °C  
Humidity 10 % to 80 % (without condensation)  
External dimension  
Weight  
: 171 mm x 47 mm x 243 mm (W x H x D)  
: 1.7 kg  
The specifications and appearance of this unit are subject to change without notice.  
7
 
VICTOR COMPANY OF JAPAN, LIMITED  
is a registered Trademark owned by VICTOR COMPANY OF JAPAN, LTD.  
is a registered Trademark in JAPAN, the U.S.A., the U.K. and many other countries.  
Printed in Japan  
LST0038-001B  
© 2002 VICTOR COMPANY OF JAPAN, LIMITED  
 

Indesit Washer Dryer WIDXL 146 User Manual
Indesit Washer Dryer WIL 144 SP User Manual
Indesit Washer Dryer WIL163UK User Manual
Init TV Video Accessories NT MG302 User Manual
Intel Switch 82550 User Manual
Jackson Dishwasher Tempstar GP User Manual
Janome Sewing Machine MB 4 User Manual
JVC DVD VCR Combo HR XVS20AA User Manual
Kenmore Double Oven 7907890 User Manual
Kompernass Power Hammer PFBS 96V User Manual