ENGLISH
DEUTSCH
FRANÇAIS
NEDERLANDS
DVD Burner
INSTRUCTIONS
DVD-brenner
BRUKSANVISNING
Записывающее устройство
для дисков DVD
ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ
DVD-Brenner
BEDIENUNGSANLEITUNG
Graveur de DVD
MANUEL D’UTILISATION
CASTELLANO
ESPAÑOL
Пристрій для запису DVD
ІНСТРУКЦІЯ
DVD-brander
GEBRUIKSAANWIJZING
Vypalovací jednotka DVD
PŘÍRUČKA K OBSLUZE
ITALIANO
DANSK
Grabador de DVD
MANUAL DE INSTRUCCIONES
Nagrywarka DVD
INSTRUKCJA OBSŁUGI
Masterizzatore di DVD
ISTRUZIONI
SUOMI
DVD-író
HASZNÁLATI UTASĺTÁSA
DVD-brænder
INSTRUKTIONSBOG
SVENSKA
NORSK
Gravador de DVD
INSTRUÇÕES
DVD-tallennin
KÄYTTÖOHJE
DVD 刻录机
使用说明书
РУССКИЙ
DVD-brännare
BRUKSANVISNING
DVD 燒錄器
УКРАЇНСЬКА
ČEŠTINA
POLSKI
CU-VD20
U/E/EK/ER/AA/AC/AG/AS/TW
MAGYAR
PORTUGUÊS
For Customer Use:
Enter the Model No. and Serial
No. (located on the bottom of the
burner) below. Retain this
information for future reference.
Model No.
Serial No.
LYT1728-001A
• Do not insert or remove the plug when your hands are wet.
• Fully insert the plug into the outlet.
DO be careful with glass panels or doors on equipment.
DON’T continue to operate the equipment if you are in any doubt
about it working normally, or if it is damaged in any way ^ switch
off, withdraw the mains plug and consult your dealer.
DON’T remove any fixed cover as this may expose dangerous
voltages.
DON’T leave equipment switched on when it is unattended unless
it is specifically stated that it is designed for unattended operation
or has a standby mode. Switch off using the switch on the
equipment and make sure that your family knows how to do this.
Special arrangements may need to be made for infirm or
handicapped people.
DON’T use equipment such as personal stereos or radios so that
you are distracted from the requirements of road safety. It is illegal
to watch television whilst driving.
DON’T listen to headphones at high volume, as such use can
permanently damage your hearing.
DON’T obstruct the ventilation of the equipment, for example with
curtains or soft furnishings. Overheating will cause damage and
shorten the life of the equipment.
DON’T use makeshift stands and NEVER fix legs with wood
screws ^ to ensure complete safety always fit the manufacturer’s
approved stand or legs with the fixings provided according to the
instructions.
DON’T allow electrical equipment to be exposed to rain or
moisture.
ABOVE ALL
• Keep dust and metal objects away from the plug.
• Do not damage the cord.
• Place the cord where it will not trip someone up.
• Do not use when thunder can be heard.
• Do not dismantle.
• Do not use for any product other than this one.
● Do not play the provided CD-ROM with an audio player. Doing so
may damage the circuits or speakers.
Safety Precautions for Discs
Do not use the following discs.
● Cracked discs
● Deeply scratched discs
Installation
Do not install in any of the following locations.
● Humid location
● Location of 60 °C or above
● Location subject to direct sunlight
● Location where overheating is likely
● Dusty or smoky locations
● Locations subject to oily smoke or steam such as a kitchen
counter or beside a humidifier
● Unstable location
● Bathroom
● Dusty places
● Slanted location
● NEVER let anyone especially children push anything into holes,
slots or any other opening in the case ^ this could result in a
fatal electrical shock;
● NEVER guess or take chances with electrical equipment of any
kind ^ it is better to be safe than sorry!
ATTENTION:
IMPORTANT (for owners in the U.K.)
On placing the unit:
Connection to the mains supply in the United Kingdom.
DO NOT cut off the mains plug from this equipment.
If the plug fitted is not suitable for the power points in your home or the
cable is too short to reach a power point, then obtain an appropriate
safety approved extension lead or consult your dealer.
In the unlikely event of the plug fuse failing be sure to replace the
fuse only with an identical approved type, as originally fitted, and
to replace the fuse cover. If the fuse fails again consult your
nearest JVC dealer.
Some TVs or other appliances generate strong magnetic fields. Do not
place such appliances on top of the unit as it may cause picture
disturbance.
When moving the product:
Press C/B to turn off the power, and wait at least 30 seconds before
unplugging the power cord. Then, wait at least 2 minutes before
moving the product.
Cleaning Procedure
If nonetheless the mains plug is cut off be sure to remove the fuse and
dispose of the plug immediately, to avoid possible shock hazard by
inadvertent connection to the mains supply.
IMPORTANT:
● Be sure to unplug the burner before beginning cleaning.
● Do not use liquid or aerosol cleaners.
● Ensure that no moisture or liquid comes into contact with the
drive during cleaning.
Exterior of the Burner:
Wipe dirt off with a dry cloth.
Disc Tray:
Wipe off dirt with a soft dry cloth.
If this product is not supplied fitted with a mains plug then follow the
instructions given below:
DO NOT make any connection to the Larger Terminal coded E or
Green.
The wires in the mains lead are coloured in accordance with the
following code:
Blue to N (Neutral) or Black
Brown to L (Live) or Red
If these colours do not correspond with the terminal identifications of
your plug, connect as follows:
Blue wire to terminal coded N (Neutral) or coloured black.
Brown wire to terminal coded L (Live) or coloured Red.
If in doubt — consult a competent electrician.
Disc:
Gently wipe from the inner edge to
the outer edge with a soft cloth.
Storage:
Make sure that discs are kept in their cases. If discs are piled on
top of one another without their protective cases, they can be
damaged. Do not put discs in a location where they may be
exposed to direct sunlight, or in a place where the humidity or
temperature is high. Avoid leaving discs in your car!
The C/B button does not completely shut off mains power from the unit,
but switches operating current on and off. ABB shows electrical power
standby and ACB shows ON.
Safety Precautions for the Burner
Be sure to observe the following precautions. Failing to do so may
result in electric shock, fire, injury, or malfunction.
● Do not disassemble, dismantle, or modify the equipment.
Requests for repair and inspection should be made to the dealer.
● Do not insert metal or combustible objects or pour water or other
liquids inside the burner.
Region Codes
Region codes are numbers for restricting DVD video playback. The
world is separated into six regions and each region is identified by
a number. If the number for a disc does not match the number for
the player, the disc cannot be played on the player. (The initial
region code is indicated on the label on the bottom of the burner.)
● Turn off the power when connecting equipment.
Changing the region codes
● Remove the plug when the burner will not be used for a
prolonged time or prior to cleaning (electricity flows through the
equipment even when the power is off).
You can change the region code to play a DVD that has a different
code. (The code cannot be changed for some playback software.)
When you insert the disc, the Caution screen appears. Follow the
on-screen instructions to change the code.
● Do not block the ventilation holes of the burner.
● Do not use where there is condensation. Suddenly carrying the
burner from a cold location to a hot location may result in the
formation of drops, which may cause a malfunction or failure.
● Do not cause the burner to vibrate when discs are in.
The region code for the burner can be changed 4 times only. The
code set the fourth time becomes the final code, so be sure to set
a frequently used code. Take sufficient care when changing the
code.
Safety Precautions for Accessories
● When using the AC adapter, the power cord, and the USB cable,
be sure to observe the following precautions. Failing to do so may
result in electric shock, fire, injury, or malfunction.
Disclaimer
JVC accepts no liability whatsoever for loss of data resulting from
inappropriate connections or handling.
EN 3
Accessories
AC Adapter (AP-V400U )
Power Cord
USB Cable
*
CD-ROM
Blank Disc
(DVD-R)
Stand
CAUTION:
Do not use AC adapter, power cord and USB cable other than those provided with this burner. Doing so may result in electric shock or fire.
NOTE:
043-124000-I2 (AC Adapter) is also available for customer using CU-VD20AC/AG/AS.
*
Guide to Parts and Controls
Front
Rear
A
B C
D
EF
A Power Button (C/B)
B Eject Button
C Power Lamp
D Disc Tray
E DC Connector
F USB Connector
Placing the Burner
This burner can be used either in the horizontal or vertical orientation. When using in the vertical orientation, align the vent of the burner and
the provided stand then place and fix the burner securely on the stand.
Bottom Surface
Stand (provided)
Vent
Inserting A Disc
When handling a disc, be sure not to touch the playback/recording side of the disc.
8 Horizontal orientation
8 Vertical orientation
4 EN
Connections
AC Adapter
(provided for the burner)
B
Power Cord
(Provided)
Hard Disk Camera
G
F
C
D
Rear of burner
To AC Outlet
To DC Connector
H
A
To USB Connector
USB Cable (Provided)
AC Adapter (provided for the camera)
E
Connecting to the Camera
A Connect the AC adapter to the burner.
B Connect the power cord to the AC adapter.
C Connect the power cord to an AC outlet.
D Connect the provided USB cable to the USB connector of the burner.
E Connect the camera to an AC outlet. (੬ Refer to the instruction manual for the camera.)
F Turn on the camera.
G Press the power button (C/B) on the front to turn on the burner. The power lamp lights in green.
H Connect the provided USB cable to the USB connector of the camera.
NOTES:
● Insert a disc after [INSERT DISC] is displayed on the camera.
● Be sure to use the provided USB cable to connect the burner and the camera.
● When using a camera, make sure the power is provided with the AC adapter, not the battery.
● Do not subject the camera or burner to vibration or mechanical shock while writing to a disc. Be especially careful if the camera is placed
on the burner during writing.
● Refer to “Dubbing Video Files To DVD Discs” in the manual for writing discs.
● The DVD discs that are written with this unit cannot be played with some DVD recorders/players. In that case, use [PLAY DVD] of the
camera to playback discs.
Connecting to PC
A Connect the AC adapter to the burner.
B Connect the power cord to the AC adapter.
Power Cord
C Connect the power cord to an AC outlet.
D Press the power button (C/B) on the front to turn on the burner.
The power lamp lights in green.
E Turn on the PC.
AC Adapter
(provided for the burner)
F Connect the burner to the PC with the USB cable.
NOTE:
To connect the burner to a PC, use the USB cable provided with the camera.
USB Cable
(provided for the camera)
EN 5
Writing Software — CyberLink Power2Go 5.5 Lite —
Power2Go 5.5 Lite is software for writing video, image, audio, and
other data files to data DVDs.
5. Enter the user information and
then click [Next].
System Requirements
The following shows the system requirements for installation.
®
®
Operating
system
Windows XP Home Edition [XP] (pre-installed) or
Windows XP Professional [XP] (pre-installed)
®
®
®
®
Intel Pentium III, at least 800 MHz
CPU
Follow the on-screen instructions.
(Intel Pentium 4, at least 2 GHz recommended)
6. Installation starts.
Free hard disk At least 50 MB for installation
space
At least 5 GB recommended for making DVDs
7. The screen on the right appears
RAM
At least 128 MB (at least 256 MB recommended)
USB 2.0/1.1* connector
when the installation is complete.
Connector
Display
Select the desired checkbox and
then click [Finish].
Must be capable of displaying 800 x 600 dots
* If you use USB1.1 cable, it will take approximately 3 hours to write.
● If you select [No, I will restart
my computer later.], the setup
complete screen in step 8.
appears.
Installation Procedure
1. Insert the installation CD-ROM in the CD-ROM drive.
8. Click [Finish].
2. The language selection screen
appears.
3. The installation start screen
appears.
Click [Next].
The installation is now finished.
NOTES:
● The above procedure is just a brief explanation on installing the
software. For details on operating Power2Go 5.5 Lite, refer to the
User’s guide, Help, and ReadMe installed at the same time as the
software. You can view the User’s guide, Help, and ReadMe from
the start menu of the PC.
4. Confirm the contents and then
click [Yes].
● This product does not apply to write files into CD-R or CD-RW.
Also, it is not responded to all the functions of Power2Go 5.5 Lite.
● To get customer support and to register the software, you need
the following product key (CD-Key):
PXNVM-NWE4G-XQD9Q-CU9DX-3FQFN-NAKUS
● Power2Go 5.5 Lite does not support conversion of audio files to
MP3 format.
● When the [Enter Activation Key] screen appears while using
Power2Go 5.5 Lite, close the screen without entering the
activation key.
CyberLink Power2Go 5.5 Lite Contact Information
For information on CyberLink Power2Go 5.5 Lite or other products, use the following contact information.
Telephone/fax support
Location
Language
Office hours (Mon. to Fri.)
Phone #
Fax #
Germany
English / German / French /
Spanish / Italian / Dutch
9:00 am to 5:00 pm
+49-700-462-92375
+49-241-70525-25
Taiwan
Mandarin
9:00 am to 6:00 pm
+886-2-8667-1298
ext. 333
+886-2-8667-1300
Paid voice support
Location
Language
Lines are open (Mon. to Fri.)
URL
U.S.A.
English
1:00 pm to 10:00 pm CST
new_site/voice_support.jsp
Support web/e-mail
Language
URL/e-mail address
English
German / French / Spanish / Italian
6 EN
Troubleshooting
If you think there is a malfunction, first check the following items. If you are still unable to solve the problem, consult your local JVC dealer.
Trouble
Cause/Action
● Make sure the AC adapter is connected properly.
Cannot turn the power on.
The camera/PC is not recognized.
The burner or AC adapter is hot.
● Make sure the USB cable is connected properly.
● This is not a malfunction. If the burner is abnormally hot, remove the AC adapter and consult the
dealer from which you purchased the burner.
Cannot open the disc tray.
● A disc cannot be ejected by pressing the eject button if data is being written to the disc. Wait until
writing finishes.
● If a disc cannot be ejected with the eject button because of a failure or a malfunction caused by,
for example, the burner being dropped, use the force eject hole to eject the disc. (See below.)
Writing fails.
● Make sure an appropriate disc is being used. (A pg. 3, 8)
● Use discs recommended for the burner. (A pg. 8)
● Insert the disc with the label facing up.
● Make sure the writing surface of the disc is not damaged.
● Make sure the disc tray is not dirty.
● Writing to irregularly shaped discs such as heart-shaped discs or octagonal discs is not possible.
● Check the writing speed of the disc being used.
Reading fails.
● Insert the disc with the label facing up.
● Make sure the writing surface of the disc is not damaged.
● Writing to irregularly shaped discs such as heart-shaped discs or octagonal discs is not possible.
● Any CD recorded using the packet-write method cannot be played.
● Any CD that does not comply with standards such as the CD-DA standard (copy-control CDs)
cannot be played.
Writing/reading at maximum speed ● Reading at maximum speed may not be possible if a non-standard disc is used.
is not possible.
● Use discs recommended for the burner. (A pg. 8)
Commercial DVDs cannot be played ● Check the region code. (A pg. 3)
when the burner is connected to PC.
It is impossible to dub the DVD discs, ● Connect the burner to the camera, playback using [PLAY DVD] function of the camera, and dub
which were written with this burner,
with DVD recorder with HDD.
the DVD discs with the DVD recorder.
(Refer to “Connecting to a TV, VCR or DVD Recorder” or “Using a DVD Burner for Dubbing” in the
camera’s manual.)
Force Eject Hole
If a disc cannot be ejected with the eject button because of a malfunction, use this hole to eject the disc.
Procedure
A Turn off the burner and disconnect the USB cable and AC adapter.
B Insert a thin rod of about 10 cm long into the force eject hole
located on the left side of the burner. The disc tray will be ejected
for about 10 mm.
C Pull out the disc tray manually and take out the disc.
NOTE:
Be sure to place the burner horizontally.
Force eject hole
Copyrights and Trademarks
Copyrights
Duplicating copyright protected material, for other than personal use, without the permission of the copyright holder is prohibited by
copyright law.
Registered Trademarks and Trademarks
®
● Windows is either registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.
● Other company and product names mentioned herein are registered trademarks and/or trademarks of their respective holders.
EN 7
Specifications
For general
Power supply
DC 12 V
Power consumption (during data transfer)
Dimensions of main unit (W x H x D)
Weight of main unit
Operating temperature
Operating humidity
Approx. 5.2 W/1.4 A
171 x 56 x 262 mm (6-3/4" x 2-1/5" x 10-3/10")
Approx. 1.4 kg (3.1 lbs)
0 °C to 40 °C (32 °F to 104 °F)
35 % to 80 %
Storage temperature
–20 °C to 50 °C (–4 °F to 122 °F)
653 to 663 nm
1.0 mW
770 to 810 nm
0.4 mW
Wavelength
Output
Wavelength
Output
For DVD
Laser Power
For CD
When connected to the camera
Interface
Supported discs
High Speed USB 2.0
DVD-R, DVD-RW
Everio
High definition Everio
DVD video (motion picture only)
Data DVD (motion picture, still picture)
Recording format
Everio
(for each 4.7 GB disc)
High definition Everio
Approx. 30 minutes (approx. 90 minutes of video recorded in fine mode)
Recording time
Interface cable
Refer to the instruction manual for the high definition Everio.
Provided USB cable
When connected to a PC
Interface
High Speed USB 2.0
DVD-R
Maximum 8x
Writing
DVD-RW
DVD-R DL
DVD-R
Maximum 4x
Maximum 4x
Maximum 12x
Writing speed
(for USB 2.0)
DVD-RW
DVD-R DL
DVD-ROM
CD-R/RW/ROM
Writing
Maximum 12x
Maximum 8x
Maximum 5x
Maximum 10x
Reading
DVD-R, DVD-R DL, DVD-RW
DVD-ROM, DVD-VIDEO, DVD-R, DVD-R DL, DVD-RW
CD-ROM, CD-DA, CD Extra, Video-CD, Mixed-CD, CD-R, CD-RW
DVD
CD
Supported disc
Reading
Reading
®
Supported operating systems
Interface cable
Windows XP Home Edition/Professional (pre-installed)
USB cable provided with the camera
Provided for the camera CyberLink PowerProducer 3 NE/PowerCinema NE for Everio (Authoring)
Supported software
Provided for the burner
CyberLink Power2Go 5.5 Lite (data writing)
Recommended discs
DVD-R
DVD-R DL
DVD-RW
JVC, TDK, Verbatim, SONY
JVC, Verbatim
JVC
Interface cable
Mini USB type A and type B, USB 1.1 and 2.0 compliant
AC adapter (AP-V400U)
Power requirement AC 110 V to 240 Vd, 50 Hz/60 Hz
Output
DC 12 V
, 4 A
NOTES:
● Only 12 cm discs can be used with this burner.
● DVD-R DL discs can be used when the burner is connected to a high definition Everio or a PC.
● A double-layer DVD-RW disc cannot be used.
● Optimal performance of the burner may not be possible depending on the disc used. Using discs of manufacturers for which compatibility
has been confirmed is recommended.
● The appearance and specifications of the product may change without notice.
● Any CD recorded using the packet-write method cannot be played.
● Operation is not guaranteed for any CD not compliant with the CD-DA standard (copy control CD).
● When connected to the PC, it may not be possible to read the audio files depending on the music CDs (CD-DA). In this case, make use of
applications such as Windows Media Player.
8 EN
© 2007 Victor Company of Japan, Limited
Printed in China
0107MNH-SW-BJ
|