JVC Network Card IF CF01PNG User Manual

VIDEO INPUT CARD  
BEDIENUNGSANLEITUNG: VIDEO-EINGANGSKARTE  
MANUEL D’INSTRUCTIONS: CARTE D’ENTRÉE VIDÉO  
ISTRUZIONI:  
SCHEDA DI INGRESSO VIDEO  
MANUAL DE INSTRUCCIONES:TARJETA DE ENTRADA VIDEO COMPUESTO  
МОДУЛЬ VIDEO ВХОДОВ  
INSTRUCTIONS  
IF-CF01PNG  
LCT2108-001A  
 
Thank you for purchasing this JVC Input Card. In order to take full advantage of the  
card’s capabilities, please read and follow all instructions carefully before installing  
and using the card. Retain this booklet for future reference.  
Precautions  
Before installing this Input Card in your monitor, please read the Safety  
Precautions included in your monitor’s user manual.  
FCC NOTICE (U.S.A. only)  
CAUTION: Changes or modifications not approved by JVC could void the user’s authority to  
operate the equipment.  
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital  
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable  
protection against harmful interference when the equipment is operated in a commercial  
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not  
installed and used in accordance with the instruction manual, may cause harmful interference to  
radio communications. Operation of this equipment in a residential area is likely to cause harmful  
interference in which case the user will be required to correct the interference at his own expense.  
EUROPE EMC STANDARD NOTICE (Europe only)  
Warning: This is a class A product. In a domestic environment this product may cause radio  
interference in which case the user may be required to take adequate measure.  
EMC Supplement (Europe only)  
This equipment is in conformity with the provisions and protection requirements of the  
corresponding European Directives. This equipment is designed for professional video appliances  
and can be used in the following environments:  
• Controlled EMC environment (for example purpose built broadcasting or recording studio), and  
the rural outdoors environment (far away from railways, transmitters, overhead power lines, etc.)  
These input cards are only for use with specific monitors.  
Consult your dealer for the compatible monitors.  
2
 
Information for Users on Disposal of Old Equipment  
[European Union]  
This symbol indicates that the electrical and electronic equipment should not be  
disposed as general household waste at its end-of-life. Instead, the product should  
be handed over to the applicable collection point for the recycling of electrical and  
electronic equipment for proper treatment, recovery and recycling in accordance  
with your national legislation.  
Attention:  
This symbol is  
only valid in the  
European  
By disposing of this product correctly, you will help to conserve natural resources  
and will help prevent potential negative effects on the environment and human  
health which could otherwise be caused by inappropriate waste handling of this  
product. For more information about collection point and recycling of this product,  
please contact your local municipal office, your household waste disposal service  
or the shop where you purchased the product.  
Union.  
Penalties may be applicable for incorrect disposal of this waste, in accordance with  
national legislation.  
(Business users)  
If you wish to dispose of this product, please visit our web page  
[Other Countries outside the European Union]  
If you wish to dispose of this product, please do so in accordance with applicable  
national legislation or other rules in your country for the treatment of old electrical  
and electronic equipment.  
3
 
Before Installation  
7 Accessaries  
• Label (x 1):  
For placing to the rear panel and the remote control of the monitor after installing  
the Input Card.  
• Slot cover (x 1): For covering the blank slot.  
7 Preparation  
• Wear gloves to protect your hands from metal parts on the Input Card’s board.  
You will need a 6 mm Phillips screwdriver.  
Turn off the monitor’s main power and unplug the power cable from the AC outlet.  
• Place the monitor with its LCD panel side down on a soft cloth so as not to damage the LCD panel.  
7 Cautions  
• Do not touch the terminals or board pattern of the Input Card to keep it from being damaged by  
static electricity.  
• Do not damage the Input Card’s connection terminal.  
• Do not put anything into the Input Card’s holes or intakes.  
• Do not force the Input Card into the monitor’s slot.  
• Attach the slot cover on the monitor’s slot in which no Input Card is installed.  
• Attach the Input Card before mounting the monitor on the stand or wall mounting unit.  
Installation  
7 Installation procedure  
1. Remove the slot cover from the  
Slot cover  
slot on the bottom side of the  
monitor.  
The monitor in the illustration is GM-H40L2.  
4
 
Installation (continued)  
Ex.: When installing only one Input Card  
Insert 1, then 2.  
2. Insert the Input Card into the slot,  
fitting into the guides inside the  
slot, so that its panel touches the  
bottom of the monitor.  
Guide  
You can install the Input Card(s) into  
either left or right slot. When installing,  
follow the procedure below.  
When installing two Input Cards:  
Install either of Input Cards into the left  
slot first.  
When installing only one Input Card:  
You need to attach the supplied slot  
cover to the blank slot.  
Panel  
Slot cover (supplied)  
or  
Install either Input Card or the supplied  
slot cover into the left slot first as  
illustrated on the right.  
Slot cover (supplied)  
Guide  
Panel  
3. Secure the Input Card by using the  
screws removed in Step 1 on the  
previous page.  
After installation  
On the rear panel  
• Place the supplied labels on the rear panel and the  
remote control of the monitor as illustrated on the right.  
On the rear panel: Place the label on the name of the  
slot into which you have installed the Input Card.  
On the remote control: Place the label on the printing  
of the corresponding input select buttons.  
• Make sure the Input Card is correctly recognized by  
“INPUT CONFIGURATION” (“INPUT C” – “INPUT F”) on  
the main menu of the monitor.  
On the remote control  
5
 
Controls and Features  
Front view  
Label  
Rear view  
6
 
1 Audio signal input terminals  
Accepts analog audio signals.  
Connect only the L/MONO terminal for monaural sound.  
2 Composite signal input/output terminals  
Accepts composite signals.  
See page 8 for the signal formats compatible with this input card.  
Select input by using the button on the monitor.  
Input select: INPUT C (SLOT-1)/E (SLOT-2)  
NTSC and PAL are switched by setting “COLOR SYSTEM” on the monitor. Refer to  
your monitor instruction manual for more information.  
NOTE:  
• The IN and OUT terminals are bridge-connected (auto termination).  
3 Synchronized signal input/output terminals  
Accepts the synchronized signals (Black burst signals).  
When using these terminals, set “SYNC SELECT” to “EXT.” on the monitor. Refer to  
your monitor instruction manual for more information.  
NOTE:  
• The IN and OUT terminals are bridge-connected (auto termination).  
4 Label (see page 5)  
1 On the rear panel: Place the label on the name of the slot into which you have  
installed the Input Card.  
2 On the remote control: When the input signal type for input B is fixed (RGB,  
COMPO., or DVI), place the corresponding label on the printing of the input select  
buttons A and B.  
3 On the remote control: Place the label on the printing of the input select buttons  
(C/D or E/F) for the slot into which you have installed the Input Card. (“NO CARD” is  
for a blank slot.)  
5 Connection terminal (on the rear side)  
Attach to the connection terminal in the slot of your monitor.  
7
 
Specifications  
Model name:  
IF-CF01PNG  
Type:  
Video Input Card  
Target monitors:  
Inputs/Outputs:  
Consult your dealer.  
Composite signal input/output:  
VIDEO: 1 line, BNC x 2, 1.0 V(p-p), 75  
• The IN and OUT terminals are bridge-connected (auto  
termination).  
Synchronized signal (Black burst signal) input/output:  
EXT. SYNC: 1 line, BNC x 2, 0.3 V(p-p), 75 Ω  
• The IN and OUT terminals are bridge-connected (auto  
termination).  
Audio signal input:  
AUDIO (L/MONO, R): 1 line, RCA x 2, 0.5 V(rms)  
Compliant signal format: NTSC, PAL, SECAM, PAL60, NTSC4.43, PAL M, PAL N,  
BW (50 Hz/60 Hz)  
Required slots:  
Weight:  
1
0.4 kg (0.9 lbs)  
Dimensions (W x H x D): 133 mm x 34.5 mm x 185 mm  
(5 1/4 inch x 1 3/8 inch x 7 3/8 inch)  
7 Dimensions  
Unit: mm (inch)  
Front View (Terminal Side)  
133 (5 1/4)  
Top View  
113 (4 1/2)  
34.5  
(1 3/8)  
185  
(7 3/8)  
22 (7/8)  
8
 
© 2006 Victor Company of Japan, Limited  
0306MKH-MW-VP  
 

Indesit Washer IWC 81481 User Manual
Insignia Flat Panel Television 20ED310NA15 User Manual
Intel Network Card 21143 User Manual
Jackson Gas Heater Heater Replacement User Manual
JVC DVD VCR Combo 3834RP0093F User Manual
JVC Flat Panel Television GR D73 User Manual
Kawasaki Utility Trailer Model ZX1200 B3H 2004 User Manual
Kenwood Two Way Radio TK 390 User Manual
KitchenAid Microwave Oven KMHP519ESS User Manual
Kowa Inflatable Bouncy Toy fm600 User Manual