JVC Speaker System SP XF10S User Manual

SATELLITE SPEAKER SYSTEM  
SATELLITEN-LAUTSPRECHER-SYSTEM  
SYSTEME HAUT-PARLEURS SATELLITE  
SATELLIET LUIDSPREKERSYSTEEM  
SYSTEMA DE ALTAVOZ DE SATÉLITE  
SISTEMA DI ALTOPARLANTI SATELLITE  
SATELLITHÖGTALARSYSTEM  
SATELLIITTIKAIUTINJÄRJESTELMÄ  
SATELLIT HØJTTALERSYSTEM  
SYSTEM G¸OÂN∏KÓW SATELITARNYCH  
SZATELIT HANGSZÓRÓ REND  
SATELITNÍ REPRODUKTOROV¯ SYSTÉM  
САТЕЛЛИТНАЯ АКУСТИЧЕСКАЯ СИСТЕМА  
SP-XF20  
INSTRUCTIONS  
BEDIENUNGSANLEITUNG  
MANUEL DINSTRUCTIONS  
GEBRUIKSAANWIJZING  
MANUAL DE INSTRUCCIONES  
ISTRUZIONI  
BRUKSANVISNING  
KÄYTTÖOHJE  
INSTRUKTIONSBOG  
INSTRUKCJA OBS¸UGI  
HASZNÁLATI UTASÍTÁSA  
P¤ÍRUâKA K OBSLUZE  
ИНСТРУКЦИИ ПО ЭКСПЛУАТАЦИИ  
LVT1201-001A  
[E]  
 
Thank you for purchasing JVC speakers.  
Before you begin using them, please read the instructions carefully.  
English  
Speaker units  
Connections  
1
Speaker cord  
Center speaker (1)  
Surround speaker (2)  
Front speaker (2)  
Connect the speaker cords to the speaker terminals.  
2
Precautions for installation and daily use  
Be sure to have the speakers installed on the wall by a qualified  
personnel to avoid unexpected damage from falling off the wall due to  
incorrect installation or weakness in the wall structure.  
Care must be taken in selecting the location of installation on the wall.  
Injuries or damages may result if the speakers installed interfere with  
daily activities.  
Press  
Insert  
Release  
Red (+)  
Black ()  
The speakers are magnetically shielded to avoid color distortions on  
TVs if they are installed properly.  
SP-XF20C  
(Rear)  
Copper  
Black striped  
When placing the speakers near a TV set, turn off the TVs main  
power switch or unplug it before installing the speakers.  
Then wait at least 30 minutes before turning on the TVs main power  
switch again. If there are still distortion, move the speakers further  
away from the TV.  
Do not reproduce sounds at so high a volume that they are distorted;  
otherwise, the speakers may be damaged by internal heat buildup.  
When moving the speakers, do not pull the speaker cords; otherwise,  
the speakers may fall over, causing damage or injury.  
SP-XF20F  
(Rear)  
Press  
Red (+)  
Black ()  
Connecting the speaker system to the amplifier  
Before connecting—  
Insert  
Turn off the power to the amplifier before connecting the speaker  
system; otherwise, the speakers may be damaged.  
The impedance of each speaker is 6 . Before connecting them to your  
amplifier, check the speaker impedance range of your amplifier. If the  
impedance of this speaker is out of the speaker impedance range  
indicated on the amplifier, you cannot connect this system to the amplifier.  
The maximum power handling capacity of the speakers are 100 W.  
Excessive input will result in abnormal noise and possible damage.  
Be sure to turn down the volume level to prevent unwanted noise  
before performing following operations:  
Black striped  
Copper  
Release  
SP-XF10S  
(Bottom)  
Turning on or off other components,  
Operating the amplifier,  
Tuning FM stations,  
Fast-forwarding a tape,  
Black striped  
Copper  
Continuously reproducing high frequency oscillation or high pitch  
electronic sounds,  
Through the hole  
Connecting or disconnecting a microphone.  
Connecting the speakers to the amplifier.  
When using a microphone, do not aim it at the speakers or use it near  
the speakers; otherwise, the howling which occurs may damage the  
speakers.  
Before replacing the cartridge, always turn off the power to the  
turntable; otherwise, the clicking noise may damage the speakers.  
3
Front left  
Front right  
Center  
Amplifier  
Subwoofer  
Specifications  
Type (magnetically-shielded type):  
SP-XF20F/SP-XF20C:  
SP-XF10S:  
2-way 3-speaker Bass-reflex type  
1-way Bass-reflex type  
Speaker units:  
Surround left  
Surround right  
SP-XF20F/SP-XF20C:  
SP-XF10S:  
Power handling capacity/Impedance: 100 W/6 Ω  
5.5 cm cone (× 2), 3.0 cm dome  
8.0 cm cone  
Connect the speakers to the speaker terminals of the amplifier  
with the speaker cords by referring to the diagram below.  
Make sure to match the polarity (ª and ·) when connecting  
the speaker cords.  
Frequency range:  
SP-XF20F/SP-XF20C:  
SP-XF10S:  
Sound pressure level:  
SP-XF20F/SP-XF20C:  
SP-XF10S:  
Dimensions (W × H × D): SP-XF20F: 84 mm × 211 mm × 88 mm  
SP-XF20C: 209 mm × 85 mm × 92 mm  
90 Hz to 40 000 Hz  
80 Hz to 20 000 Hz  
The diagram below is an example of a typical connection.  
FRONT LEFT  
CENTER  
81 dB/Wm  
75 dB/Wm  
FRONT RIGHT  
FRONT CENTER SURROUND SURROUND  
BACK  
SPEAKERS  
RIGHT LEFT  
RIGHT  
LEFT  
Recommended to use  
SP-SB100 (optionally  
purchased).  
SP-XF10S: 111.5 mm × 139 mm × 106.5 mm  
Mass:  
SP-XF20F/SP-XF20C:  
SP-XF10S:  
0.87 kg each  
0.52 kg each  
4 m (× 3); 10 m (× 2)  
SURROUND RIGHT  
SURROUND LEFT  
Accessories: Speaker cords:  
Design and specifications are subject to change without notice.  
– 3 –  
 
EN, GE, FR, NL, SP, IT, SW, FI, DA, PO, HU, CZ, RU  
© 2004 Victor Company of Japan, Limited  
0404NSMMDWHCE  
 

Insignia Flat Panel Television NS L42X 10A User Manual
JVC Car Video System KV MR9010 User Manual
JVC DVD Player XV S60BK User Manual
JVC Flat Panel Television LT WX84 User Manual
JVC Security Camera LWT0254 001B H User Manual
JVC VCR HR J259EE User Manual
Kenmore Cooktop 318201439 User Manual
Kenwood Stereo Amplifier B64 2562 00 00 User Manual
KitchenAid Cooktop KICU500 User Manual
Krell Industries CD Player KAV 300cd User Manual