45406
Home Monitoring
Wired Color
Camera
User Manual
For indoor/outdoor use. Do not use in wet locations
1-800-654-8483
3
PACKAGE CONTENTS
Please check and identify all the parts before
proceeding with the installation.
1. 45406 Wired Color Camera with desktop mount
2. AC/DC Adapter
3. Wall Mounting Kit (wall mount, 1 screw, 1 plastic
anchor, 20 cord clips)
4. 60’ Camera connection cable (not rated for in-
wall use.)
INSTALLING AND VIEWING THE CAMERA
Before starting the installation, we recommend
you temporarily connect the camera to your TV to
help determine the best location for installing the
camera.
• The camera will connect to RCA audio/video
jacks on your TV/VCR/DVR.
• There are two connection methods shown.
Choose the best one for your requirements.
CONNECTION METHOD 1
To view the 45406 Color Camera picture:
1. Switch on the TV and set the volume to
midpoint. Connect power to the 45406 Wired Color
Camera.
4
TV
Power
Video In
Audio In
2. Select the AV channel on your TV by pressing
the button labeled “AV” (sometimes also labeled
as “Input”, “Mode”, or “Function”) on your TV or its
remote control. You should now be able to see and
hear the output from the camera.
CONNECTION METHOD 2
If you are using a VCR/DVR with RCA jacks, connect
the camera as shown on next page:
To view the 45406 Wired Color Camera picture:
1. Switch on the TV, the VCR or DVR and set the
volume to midpoint. Connect the power adapter to
the camera, and the other end to an AC outlet.
2. Select the AV channel on your TV by pressing
the button labeled “AV” (sometimes also labeled
5
TV
Power
Audio Video
In In
VCR
Audio
In
Video
In
Audio Video
Out Out
as “Input”, “Mode”, or “Function”) on your TV or its
remote control. This should be the channel you
normally use for watching the VCR or DVR. You
should now be able to see and hear the output from
the camera.
WHERE TO POSITION THE CAMERA
The 45406 Wired Color Camera is suitable for
indoor or outdoor use. Remember the following
points when choosing a mounting position:
• When installing camera outside, mount it in a
sheltered location such as under an eave.
• The camera must be positioned so it will not
point directly into the sun or any bright light,
as this may damage the camera.
6
• Avoid viewing areas where half the area is
in bright sunlight and the other half is dark,
such as the shadow of a building. All types of
cameras have difficulty in “seeing” with such a
large light-level variation.
• The camera will work in low light conditions,
but it will function better if a light, (such as a
100W incandescent lamp) is present near the
camera for good visibility at night.
• The camera cable may be extended up to
300 ft. with additional cable (not supplied.)
Remember this when choosing a location for
the camera. An additional 60 ft. extension
cable is available; contact Customer Service at
800-654-8483.
COMPLETING THE INSTALLATION
Once the camera position is chosen, complete the
installation as follows:
1. Disconnect the power to the camera.
2. Attached the camera to the wall as shown.
-
-
Audio hole
of camera
indicates bottom
7
3. The bracket can also be attached to the camera
in two different ways, choose the method which
suits you best.
Ceiling mount
Desktop mount
Wall mount
4. Run the 60’ cable from the TV/VCR/DVR location
to the camera and reconnect to the camera cable.
Use the cord clips provided to keep the cable in
place.
5. If you disconnected the camera leads from the
TV/VCR/DVR, reconnect the cable.
6. Switch on the power to the TV/VCR/DVR.
7. Select the AV channel on the TV/VCR/DVR to
which the camera is connected. You should hear
and see the camera output.
8. Any slight adjustments can now be made to
the camera viewing angle by carefully tilting and
panning the camera head.
8
NOTES ON CABLE INSTALLATION
• Keep the camera cable away from other cables
where possible, in order to reduce the risk of
picture and audio interference.
• Avoid laying the cable next to any heat sources.
• If the cable is run along the ground, a protective
covering must be used to prevent the cable from
being damaged.
• Do not run the cable inside walls.
• Do not pierce, puncture, or cut cable when
installing.
If you have any questions or feel the camera
system is not operating correctly, or you simply
need additional information, please visit our
Customer Service Group at 1-800-654-8483.
SPECIFICATIONS (Subject to change without notice.)
AC/DC Adapter
Power supply operating voltage................................................120V 60Hz
Output voltage...............................................................................................9V DC
Output current.............................................................................................100mA
Camera
Camera operating voltage......................................................................9V DC
Current consumption..........................................................45mA maximum
9
Camera type..............................................................................color 1/4” CMOS
Horizontal resolution.....................................................................360 TV lines
Lens....................................................................................................................5.6mm
Minimum illumination...................................................................................3 lux
Video signal output.......................................... NTSC 1 Vp-p into 75 Ohm
Audio signal output.....................................................2 Vp-p into 47k Ohm
Operating temperature ................................-10°~+40° C (14° to 104° F)
Overall size.....................................................................................Diameter: 1.6”
Pre-connected Cable type...........................................6 conductor cable
Lead Connectors .............................................................6 pin mini-DIN plug
60’ Lead Cable type..........................................................6 conductor cable
Connectors.....................................................................6 pin mini-DIN socket
WARRANTY
ONE-YEAR LIMITED WARRANTY: Jasco Products Company
warrants this product to be free from manufacturing defects
for a period of one year from the original date of consumer
purchase. This warranty is limited to the repair or replacement
of this product only and does not extend to consequential or
incidental damage to other products that may be used with
this unit. This warranty is in lieu of all other warranties express
or implied. Some states do not allow limitations on how long an
implied warranty lasts or permit the exclusion or limitation of
incidental or consequential damages, so the above limitations
may not apply to you. This warranty gives you specific rights,
and you may also have other rights which vary from state to
state. If unit should prove defective within the warranty period,
return prepaid with dated proof of purchase to:
Jasco Products Company
10 E. Memorial Road, Oklahoma City, OK 73114
10
WARNING
Risk of fire and shock
• Only use the supplied cUL listed AC to DC adapter.
• The supplied adapter is for indoor use only.
• Do not run the camera cable inside walls; when securing the
cable, do not cut or puncture
• Do not use in wet locations
FCC STATEMENT
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician
for help.
11
Made in China
is a trademark of General Electric Company
and is used under license to Jasco Products Company LLC,
10 E. Memorial Road, Oklahoma City, OK 73114
|