Jensen Clock Radio JCR 300 User Manual

MODEL JCR-300  
AM/FM TALKING DUAL ALARM CLOCK RADIO  
WITH TALK ’N SET®  
USER MANUAL  
PLEASE READ THIS USER MANUAL COMPLETELY BEFORE  
OPERATING THIS UNIT AND RETAIN THIS BOOKLET FOR  
FUTURE REFERENCE.  
 
11) Only use attachments/accessories specified by the manufacturer.  
12) Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with  
the apparatus. When a cart is used, use caution when moving the cart/apparatus combination  
to avoid injury from tip-over.  
13) Unplug this apparatus during lightning storms or when unused for long  
periods of time.  
14) Refer all servicing to qualified service personnel. Servicing is required  
when the apparatus has been damaged in any way, such as power-supply  
cord or plug is damaged, liquid has been spilled or objects have fallen into  
the apparatus, the apparatus has been exposed to rain or moisture, does  
not operate normally, or has been dropped.  
15) The apparatus shall not be exposed to dripping or splashing and that no objects filled with  
liquids, such as vases, shall be placed on apparatus.  
16) Main plug is used as disconnect device and it should remain readily operable during intended  
use. In order to disconnect the apparatus from the mains completely, the mains plug should  
be disconnected form the mains socket outlet completely.  
17) Battery shall not be exposed to excessive heat such as sunshine, fire or the like.  
18) The marking information is located at the bottom of apparatus.  
19) CAUTION  
Danger of explosion if battery is incorrectly replaced. Replace only with the same or  
equivalent type.  
CAUTION:  
TO PREVENT ELECTRIC SHOCK,  
MATCH WIDE BLADE OF AC PLUG TO WIDE SLOT.  
FULLY INSERT.  
SAVE THIS INSTRUCTIONS  
COMPLIANCE WITH FCC REGULATIONS  
This equipment has been tested and found to comply with the limits for a radio receiver, pursuant  
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against  
harmful interference in a residential installation. This equipment generates, uses and can radiate  
radio frequency energy and, if not installed and used in accordance with the instructions, may  
cause harmful interference to radio communications. However, there is no guarantee that  
interference will not occur in a particular installation. If this equipment does cause harmful  
interference to radio or television reception, which can be determined by turning the equipment off  
and on, the user is encouraged to try to correct the interference by one or more of the following  
measures:  
- Reorient or relocate the receiving antenna.  
- Increase the separation between the equipment and receiver.  
- Connect the equipment into an outlet on a circuit different from that to which the receiver is  
connected.  
- Consult the dealer or an experienced radio/TV technician for help.  
WARNING  
Changes or modifications to this unit not expressly approved by the party responsible for  
compliance could void the user's authority to operate the equipment.  
E-2  
 
DEAR JENSEN CUSTOMER  
Selecting fine audio equipment such as the unit you've just purchased is only the start of your musical  
enjoyment. Now it's time to consider how you can maximize the fun and excitement your equipment offers.  
This manufacturer and the Electronic Industries Association's Consumer Electronics Group want you to  
get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud  
and clear without annoying blaring or distortion and, most importantly, without affecting your sensitive  
hearing.  
Sound can be deceiving. Over time your hearing "comfort level" adapts to higher volumes of sound. So  
what sounds "normal" can actually be loud and harmful to your hearing. Guard against this by setting your  
equipment at a safe level BEFORE your hearing adapts.  
To establish a safe level:  
Start your volume control at a low setting.  
Slowly increase the sound until you can hear it comfortably and clearly, and without distortion.  
Once you have established a comfortable sound level:  
Set the dial and leave it there.  
Taking a minute to do this now will help to prevent hearing damage or loss in the future. After all, we want  
you listening for a lifetime.  
We Want You Listening For a Lifetime  
Used wisely, your new sound equipment will provide a lifetime of fun  
and enjoyment. Since hearing damage from loud noise is often  
undetectable until it is too late, this manufacturer and the Electronic  
Industries Association's Consumer Electronics Group recommend you  
avoid prolonged exposure to excessive noise.  
Customer's Record:  
The serial number of this product is found on its bottom. You should note the serial number of this unit in  
the space provided as a permanent record of your purchase to aid in identification in the event of theft of  
loss.  
Model Number: JCR-300  
Serial Number: ____________________  
E-3  
 
LOCATION OF CONTROLS  
Controls and Functions of Unit  
1. Volume Control  
12. On/Off Button  
2. ALARM 1 (AL1) On/Off Button  
3. Trigger On/Off Switch  
4. < (Down) Button  
13. LCD Panel  
14. Rating Label  
15. Reset Button  
5. Set Button  
6. > (Up) Button  
16. Battery Compartment Cover  
17. Speaker  
7. AM/FM Band Selector  
8. ALARM 2 (AL2) On/Off Button  
9. Tuning Control  
18. Line In Jack  
19. Display Hi/Lo Dimmer Button  
20. FM Wire Antenna  
21. AC Power Cord  
10. Sleep Button  
11. Snooze Bar (also works as Trigger Button  
for “Talk ’N Set”)  
LCD Panel Indicators  
22. PM Indicator  
23. Hour Digits  
24. Minute Digits  
25. AL1 and Sound Effect  
Indicators  
26. AL2 and Sound Effect  
Indicators  
27. SLEEP and Sound Effect  
Indicators  
28. SNOOZE Indicator  
29. Talk ’N Set Indicator  
E-4  
 
IMPORTANT NOTES  
Avoid installing the unit in locations described below:  
Places exposed to direct sunlight or close to heat radiating appliances such as electric heaters.  
Humid, moist or dusty places.  
Places subject to constant vibration.  
Noisy places.  
POWER REQUIREMENTS  
This unit operates on 120V~ 60Hz and requires 2 x CR2032 Lithium batteries (included) for system and time  
backup during power outage. Prior to first use, please remove the plastic battery insulator tab to activate the  
backup batteries. Do not attempt to operate the radio on any other power source. You could cause damage  
to the unit and void your warranty.  
REPLACING BACKUP BATTERIES  
1. Remove the screw from the BATTERY COMPARTMENT COVER and remove the compartment.  
2. Remove both batteries. Install 2 brand new CR2032 Lithium 3V batteries according to the polarity  
markings on the BATTERY COMPARTMENT COVER.  
3. Replace the BATTERY COMPARTMENT COVER and tighten the screw to secure the compartment.  
NOTE: The unit will operate without batteries installed, but your time and alarm settings will be lost and have  
to be reset in the event of a power interruption or failure.  
IMPORTANT: Be sure that the batteries are installed correctly.  
Wrong polarity may damage the unit and void the warranty.  
For best performance and longer operating time, we recommend the use of good quality  
batteries.  
CAUTIONS  
1. Do not mix old and new batteries.  
2. Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.  
3. If the unit is not to be used for an extended period of time, remove the batteries. Old or leaking batteries  
can cause damage to the unit and may void the warranty.  
4. Do not dispose of batteries in fire, batteries may explode or leak.  
5. Replace all the batteries at the same time, no matter exhausted or not, every 2 years at the same time  
to avoid possible battery leakage.  
CONNECTING THE UNIT TO AC POWER SOURCE  
Please be sure the outlet you plug this unit into is working and provides uninterrupted power.  
1. Insert the AC plug of the AC power cord into a 120V~ 60Hz outlet.  
2. Press the RESET BUTTON on the bottom of the unit with a pointed object (e.g. a straighten paper clip)  
to initialize. After a brief self test, the unit enters the clock mode.  
3. To listen to the radio, press On/Off Button.  
E-5  
 
WHAT IS TALK’N SET?  
Talk ’N Set is an innovative clock operating system using the latest voice recognition  
technology. It’s the HANDS-FREE way to set your alarm clock. No more fumbling with  
instructions or pressing multiple buttons to set the time and alarm. Once the system is  
activated by saying the trigger word “Hello Clock Radio”, you now simply say one of the  
preset voice commands and follow the voice prompts to set-up the clock using your voice!  
Setting the Time, Alarm, Sleep Time, Sleep Sound and Alarm Sounds are just a few of the  
features you can control with voice commands.  
As you become more familiar with this technical marvel you will understand that it has  
been specifically programmed for voice command of multiple functions. Depending on the  
surrounding ambience (potential noise influence) and how you speak its “language”, there  
may be instances of misunderstood commands. If this happens, just repeat them after  
checking the way to say your commands so that Talk ’N Set will obey and also talk to you  
properly. Finally this product can have all functions operated manually the same as all  
other clock radios.  
SETTING UP DAILY ALARMS AND CLOCK  
USING MANUAL SETTINGS  
In radio off mode, press SET BUTTON (#5) to enter AL1/AL2/Time setup mode.  
1. The HOUR DIGITS and AL1 indicator in the LCD panel will flash.  
2. Using the > (UP) (#6) or < (DOWN) (#4) BUTTONS, adjust to the desired hour for AL1.  
3. Press SET BUTTON (#5). The MINUTE DIGITS and AL1 indicator in the LCD panel will flash (#25).  
4. Using the > (UP) (#6) or < (DOWN) (#4) BUTTONS, adjust to the desired minute for AL1.  
5. Press SET BUTTON (#5). The SOUND EFFECT INDICATORS of AL1 will flash (#25).  
6. Use the > (UP) (#6) or < (DOWN) (#4) BUTTONS to choose a Wakeup Alarm Sound - Ocean, Rain,  
Brook, Radio or Beep Alarm.  
7. Press SET BUTTON (#5) to proceed to AL2 settings following steps #1 to 6 above. AL2 indicators (#26)  
will respond to the features chosen.  
8. Press SET BUTTON (#5) to proceed to TIME settings following steps #1 to 4 above.  
9. Press SET BUTTON (#5) to proceed to Sleep Sound settings.  
10. Use the > (UP) (#6) or < (DOWN) (#4) BUTTONS to choose a Sleep Sound - Ocean, Rain, Brook or  
Radio.  
11. Except in alarm, snooze or sleep modes, you may cycle through and review the set alarm time, alarm  
sound and sleep sound settings by pressing the SET BUTTON (#5) repeatedly.  
USING TALK ’N SET  
For correct operation of TALK ’N SET, please be sure to operate the unit in the following conditions:  
-
-
-
-
The ambient condition is fairly quiet.  
The radio or alarm sound is not playing.  
The TRIGGER SWITCH (#3) is set to ON. It will say “On” and the “Voice” indicator (#29) will turn on.  
You are within 6 – 24 inches from the built-in MICROPHONE located on the top of the unit right behind the  
SET BUTTON (#5). (Remarks: the farther away from the mic, the louder you have to say the voice  
commands.)  
-
-
To turn off the TALK ’N SET function, slide the TRIGGER SWITCH (#3) to OFF. It will say “Off” and the  
“Voice” indicator (#29) will turn off.  
If the unit is placed in an area where there is continuous talking or ambient noises, like near a TV or  
radio, you may experience a false trigger (“OK” is heard from the speaker). Although rare, if this  
happens, you can say “Cancel” to stop the function or tap any of the control buttons on the top cabinet to  
prevent accidental changes in the time, alarm or other settings.  
TALK ’N SET COMMANDS  
COMMAND  
FUNCTION DESCRIPTION AND FACTORY PRESET  
PHRASE  
Hello Clock Radio  
Trigger word to activate the voice recognition system.  
E-6  
 
Time  
To check the current time.  
* Factory preset time is 12:00AM.  
Set Time  
Alarm  
To set the current time in AM or PM.  
To check the alarm time and status of AL1 & AL2. If the alarm is currently off,  
you have the option to turn it on or vice versa.  
* Factory preset alarm time is 7:00AM for AL1 and 8:00AM for AL2.  
Set Alarm  
To set the alarm time of AL1 & AL2 in AM or PM.  
Alarm Sound  
To set the alarm sound for AL1 & AL2. You can select from among 3 nature  
sounds (Ocean, Rain or Brook), radio or the beep alarm.  
* Factory preset alarm sound is beep alarm for both AL1 & AL2.  
To cancel current alarm for the day while alarming is sounding or clock is in  
snooze mode.  
To activate the 9 minute Snooze while an alarm is sounding. You must say the  
command word “Snooze” during the brief pause during the alarm (except radio  
mode in which you need to tap the SNOOZE BAR) for it to work correctly.  
To choose a sleep sound from among 3 nature sounds (Ocean, Rain or Brook),  
or radio and then to set sleep time for 15, 30, 45 or 60 minutes or to turn it off.  
The sleep time is default to 60 minutes. You can adjust sleep sound output  
between levels 1-4 by pressing the > (UP) (#6) or < (DOWN) (#4) BUTTONS.  
* Factory preset sleep sound is Ocean and its output level is “2”.  
To set the LCD backlight brightness to HI or LO.  
Alarm Off  
Snooze  
Play Sleep Sound  
Display  
Cancel  
* Factory preset LCD brightness is “High”.  
To terminate the Talk ’N Set function immediately after it is activated.  
It can also be used in the middle to terminate certain Talk ’N Set commands: Set  
Alarm, Alarm Sound, Play Sleep Sound and Display.  
CURRENT TIME SETTING AND REPORTING  
TO SET THE CURRENT TIME  
1. Start by saying the trigger word “Hello Clock Radio” or press the SNOOZE BAR (#11).  
2. The unit will reply “Yes” and will wait for your next command.  
3. Say “Set Time” and the unit will reply “Tell me the current time including AM or PM”.  
4. Say the current time you wish to set the clock to. Example: to set the clock to 3:23AM, say “Three  
Twenty Three AM”.  
5. When the time is successfully understood, the unit will reply, “The time is …” and repeat the time you  
gave. Example: if you said to set the time to 3:23AM, the reply will be “The time is three-twenty- three  
AM”.  
6. If the unit fails to understand the time given, it will reply, “I’m sorry. I didn’t get that. Please tell me  
the current time, for example, seven-thirty-five PM”. Now repeat step #4 above.  
7. If the unit fails to understand the time given a second time, it will reply, “I’m sorry. I did not  
understand you, please start over or set the time manually”. If this occurs, repeat steps #1 - 4  
above again making sure you speak clearly in a normal voice and avoid pauses between words.  
TO CHECK THE CURRENT TIME  
1. Start by saying the trigger word “Hello Clock Radio” or press the SNOOZE BAR (#11).  
2. The unit will reply “Yes” and will wait for your next command.  
3. Say “Time” and the unit will reply “The time is ...” followed by the present time.  
ALARM TIME AND ALARM SOUND SETTING / CHECKING  
TO SET THE ALARM TIME (AL1/AL2)  
1. Start by saying the trigger word “Hello Clock Radio” or press the SNOOZE BAR (#11).  
2. The unit will reply “Yes” and will wait for your next command.  
3. Say “Set Alarm” and the unit will reply “Say Alarm One or Alarm Two”.  
4. To set Alarm One, say “Alarm One”. You can also say the command “Cancel” during this step if you  
wish to cancel setting the alarm and the unit will reply “OK” to confirm..  
5. If the unit fails to understand the alarm source given, it will reply, “Please Repeat”. Now repeat step  
#4 above.  
6. If the unit fails to understand the alarm source given a second time, it will reply “I’m sorry. I did not  
understand you, please start over or set the alarm time manually”. If this occurs, repeat steps #1 -  
4 above again making sure you speak clearly in a normal voice.  
E-7  
 
7. When the alarm source is successfully understood, the unit will reply, “Please say the time you would  
like the alarm to sound, including AM or PM” while the current alarm time is displayed.  
8. Say the time you wish Alarm One to sound in a clear, normal voice without any pause between words.  
Example: to set Alarm One to 10:19AM, say “Ten Nineteen AM”.  
9. When the alarm one time is successfully understood, the unit will reply “Alarm One is now set to …”  
and repeat the time you gave. Example: if you said to set the alarm time to 10:19AM, the reply will be  
“Alarm One is now set to ten-nineteen AM”. The Alarm One indicator on the display (#25) will now light.  
10. If the unit fails to understand the alarm time given, it will reply, “I’m sorry, I didn’t get that. Please tell  
me the time you would like the alarm to set, for example, eight-thirty AM”. Now repeat step #8  
above.  
11. If the unit fails to understand the alarm time given a second time, it will reply “I’m sorry. I did not  
understand you, please start over or set the alarm time manually”. If this occurs, repeat steps #1 –  
4 and 8 above again making sure you speak clearly in a normal voice and avoid pauses between words.  
12. To set Alarm Two, repeat steps #1 - 4 above and say “Alarm Two” when prompted (step #4). The  
Alarm Two indicator on the display (#26) will light once complete.  
TO SET THE ALARM WAKE SOUNDS (AL1/AL2)  
1. Start by saying the trigger word “Hello Clock Radio” or press the SNOOZE BAR (#11).  
2. The unit will reply “Yes” and will wait for your next command.  
3. Say “Alarm Sound” and the unit will reply “To set alarm sound, please say Alarm One or Alarm  
Two”.  
4. To set Alarm One, say “Alarm One”. You can also say the command “Cancel” during this step if you  
wish to cancel setting the alarm sound.  
5. If the unit fails to understand the alarm source given, it will reply, “Please Repeat”. Now repeat step  
#4 above.  
6. If the unit fails to understand the alarm source given a second time, it will reply “I’m sorry. I did not  
understand you, please start over or set the alarm sound manually”. If this occurs, repeat steps  
#1 - 4 above again making sure you speak clearly in a normal voice.  
7. When the alarm source is successfully understood, the unit will reply, “To choose an alarm sound,  
say Ocean, Rain, Brook, Radio or Beep”.  
8. Say Ocean, Rain, Brook, Radio or Beep. You can also say the command “Cancel” during this step if  
you wish to cancel setting the alarm sound and the unit will reply “OK” to confirm.  
9. When the alarm sound is successfully understood, the unit will reply “Alarm One sound is set to…”  
and repeat the alarm sound you have chosen. The alarm one sound selected will light in the display  
(#25).  
10. If the unit fails to understand the alarm sound given for the first and second times, it will reply “Please  
Repeat”. Now repeat step #8 above.  
11. If the unit fails to understand the alarm sound given a third time, it will reply “I’m sorry. I did not  
understand you, please start over or set the alarm sound manually”.  
12. To set Alarm Two Sound, repeat steps #1 – 4 and 8 above and say “Alarm Two” when prompted  
(step #4). The alarm two sound selected will light in the display (#26) when completed.  
NOTE:  
-
-
-
When the preset alarm time is reached, the chosen alarm sound will start sounding at a fairly low  
volume level and gradually increase to a very loud volume level in 60 seconds. It will last for 60 minutes  
if uninterrupted.  
When the alarm is sounding, there will be a periodic pause in the alarm sound if you chose a nature  
sound (Ocean, Rain or Brook) or the Beep for your wake alarm. This is normal and the point where the  
unit is listening for one of the two Talk ’N Set commands (“Snooze” or “Alarm Off”).  
If radio is chosen as the alarm sound, you will not be able to use Talk ’N Set commands to activate  
snooze or turn the alarm off. This will need to be done manually by pressing either AL1 ON/OFF (#2),  
AL2 ON/OFF (#8) or ON/FF (#12) BUTTON.  
-
-
-
If the latter alarm time is reached before the first sounding alarm has ended, the first alarm will be  
instantly overridden and the new alarm session will sound for 60 minutes if uninterrupted.  
An active alarm will always sound no matter the unit is off, in sleep mode or playing through a  
radio/external MP3 player.  
If you choose the radio alarm but an external audio device remains to be connected to the LINE IN  
JACK (#18) by a stereo cord (not included) when the alarm time is reached, the beep alarm will  
automatically switch in to substitute the radio alarm.  
TO CHECK THE ALARM TIME (AL1/AL2)  
E-8  
 
1. Start by saying the trigger word “Hello Clock Radio” or press the SNOOZE BAR (#11).  
2. The unit will reply “Yes” and will wait for your next command.  
3. Say “Alarm” and the unit will announce the Alarm One time, play a brief sample of the alarm sound  
and also ask if you want to turn the alarm off if on.  
4. Alarm Two settings will be announced in the same way once the Alarm One setting checks are  
completed.  
a. Example: You say “Alarm”.  
b. The unit will reply, “Alarm One is set to …” and announce the time alarm one is set to.  
c. If Alarm one is on, the unit will continue, “The Alarm is On” and play a brief sample of the alarm  
sound for it.  
d. The unit will now ask “Would you like to turn off the Alarm?”  
e. If you say “Yes”, the unit will reply “Alarm One is Off” and proceed to announce the Alarm Two  
settings. If you say “No”, it will proceed to Alarm Two.  
f. Alarm Two check will be announced in the same way as alarm one above.  
SNOOZE FUNCTION  
When the preset alarm time is reached, the chosen alarm sound will start. You can momentarily stop the  
alarm sound for 9 minutes by using the snooze function. The snooze function can be repeated for a  
maximum of 6 times within 60 minutes from the original preset alarm time.  
MANUAL OPERATION  
1. When any alarm is sounding, press the SNOOZE BAR (#11) for a 9-minute snooze.  
2. The SNOOZE INDICATOR (#28) will turn on.  
3. When snooze expires, the alarm sound will resume.  
4. You can repeat snooze operation for a maximum of 6 times within 60 minutes from the original preset  
alarm time.  
5. You can cancel snooze any time by pressing the ON/OFF BUTTON (#12).  
6. The SNOOZE INDICATOR (#28) will go off.  
7. The alarm will now be off and ready to sound the next day at the preset time.  
USING TALK ’N SET  
1. When the designated alarm time is reached, there will be a periodic pause in the alarm sound if you  
have chosen a nature sound (Ocean, Rain or Brook) or the Beep for your wake alarm. This is normal  
and during the pause is where the unit is listening for the “Snooze” command.  
Note: If radio is chosen as the alarm sound, it will play without interruption and therefore you will not be  
able to use Talk ’N Set “Snooze” command to activate the snooze. This will need to be done manually  
by pressing the SNOOZE BAR (#11).  
2. Say “Snooze” during one of the pauses in the alarm sound to activate the 9-minute snooze.  
3. If your command is correctly recognized, the SNOOZE INDICATOR (#28) will turn on.  
4. When snooze expires, the alarm sound will resume.  
5. You can repeat snooze operation for a maximum of 6 times within 60 minutes from the original preset  
alarm time.  
6. You can cancel snooze any time by saying “Alarm Off” or manually pressing ON/OFF BUTTON (#12).  
7. If you press the SLEEP BUTTON (#10) once, snooze and only the alarm in effect will be cancelled at  
once and go into sleep mode directly. The desired sleep time can be adjusted by pressing the SLEEP  
BUTTON (#10) repeatedly.  
8. If the “Alarm Off” command is correctly recognized, the unit will reply “Yes” and SNOOZE  
INDICATOR (#28) will go off.  
9. The alarm will now be off and ready to sound the next day at the preset time.  
TURNING OFF THE ALARM  
You can turn the alarm off for the day only so that it will sound again on the following day or you can turn the  
alarm completely off by disabling it.  
MANUAL OPERATION  
1. When an alarm is sounding, press the ON/OFF button (#12) to turn the alarm off only for the day. The  
alarm will sound again the next day at the same preset time. The alarm indicators on the display (#25 &  
#26) will remain on.  
E-9  
 
2. If you do not wish the alarm to sound again, you can disable it by pressing either the AL1 ON/OFF  
BUTTON (#2) or AL2 ON/OFF BUTTON (#8). The corresponding alarm indicators on the display (#25 &  
#26) will go off.  
3. To enable the alarms again, press either the AL1 ON/OFF BUTTON (#2) or AL2 ON/OFF BUTTON (#8).  
The corresponding alarm indicators on the display (#25 & #26) will turn on.  
USING TALK ’N SET  
1. When the designated alarm time is reached, there will be a periodic pause in the alarm sound if you  
chose a nature sound (Ocean, Rain or Brook) or the Beep for your wake alarm. This is normal and  
during the pause is where the unit is listening for the “Alarm Off” command.  
2. Say “Alarm Off” during one of the pauses in the alarm sound to turn the Alarm off for the day. If the  
“Alarm Off” command is correctly recognized, the unit will reply “Yes” and the alarm sound will stop.  
The alarm will sound again the next day at the same preset time.  
3. If radio is chosen as the alarm sound, it will play without interruption and therefore you will not be able  
to use Talk ’N Set “Alarm Off” command to turn it off. The radio alarm will have to be turned off by  
pressing either AL1 ON/OFF (#2), AL2 ON/OFF (#8) or ON/FF (#12) BUTTON.  
4. Follow the steps in the above Talk ’N Set section “TO CHECK THE ALARM TIME (AL1/AL2)” to turn  
the specific alarm off with voice commands if it is initially on. The corresponding alarm indicator on the  
display (#25 and/or #26) will turn off to confirm.  
SETTING UP THE SLEEP SOUND AND TIME  
You can choose either a nature sound (Ocean, Rain or Brook) or the radio as a sleep sound.  
The sleep time can be adjusted from: 15, 30, 45 or 60 minutes and OFF.  
MANUAL SETTING  
SETTING THE SLEEP SOUND  
1. The Sleep Sound can be set by repeatedly pressing the SET BUTTON until you get to the to Sleep  
Sound settings.  
2. Use the > (UP) (#6) or < (DOWN) (#4) BUTTONS to choose a Sleep Sound (Ocean, Rain, Brook or  
Radio).  
3. The display will show the chosen Sleep sound (#27).  
ACTIVATE SLEEP MODE AND SETTING SLEEP TIME  
1. Press the SLEEP BUTTON (#10) to start the sleep mode.  
2. The default Sleep Time is 60 minutes and “60” will show on the display (#24).  
3. Press the SLEEP BUTTON (#10) repeatedly to cycle through shorter sleep time options of 45, 30, 15  
minutes or OFF.  
USING TALK ’N SET  
SETTING THE SLEEP SOUND, TIME AND STARTING THE SLEEP FUNCTION  
1. Start by saying the trigger word “Hello Clock Radio” or press the Snooze Bar (#11).  
2. The unit will reply “Yes” and will wait for your next command.  
3. Say “Play Sleep Sound” and the unit will reply “To Choose a Sleep Sound, Say Ocean, Rain,  
Brook or Radio”.  
4. Say “Ocean”, “Rain”, “Brook” or “Radio”. You can also say the command “Cancel” during this step  
if you wish to cancel setting the sleep sound and the unit will reply “OK” to confirm.  
5. The unit will now say “Please choose a Sleep Time, say Fifteen, Thirty, Forty-Five or Sixty  
Minutes”.  
6. Say “Fifteen”, “Thirty”, “Forty-Five” or “Sixty”. You can also cancel the Sleep time by saying the  
command “Cancel”. The unit will reply “OK” to confirm.  
7. When the sleep time is successfully understood, the unit will say “The Sleep Sound will turn off in …  
Minutes”. The number you chose in step #6 will be said.  
8. The sleep time chosen will also show on the display (#24).  
9. When the sleep sound and time settings are successfully understood, the chosen sleep sound will show  
on the display (#27) and be played for the selected sleep time.  
10. If the unit fails to understand the sleep time given, it will reply “Please Repeat”. Now repeat step #6  
above.  
NOTE:  
-
During sleep, you may press the SLEEP BUTTON (#10) to check the remaining sleep time.  
E-10  
 
-
-
When sleep sound is playing, its volume can be adjusted from low to high (level 1-4) by pressing the >  
(UP) (#6) or < (DOWN) (#4) BUTTONS. The selected sleep sound volume will be displayed.  
To change the sleep sound during sleep, press the SNOOZE BAR (#11) and use “Play Sleep Sound”  
voice command to change it as usual. Say “Cancel” when asked to choose the sleep time to keep the  
current sleep time.  
LISTENING TO RADIO  
1. Select your desired radio band using the BAND SELECTOR (#7) for AM or FM.  
2. Press the ON/OFF BUTTON (#12) to turn radio on.  
3. Rotate the TUNING CONTROL (#9) to your desired radio station according to the dial scale on the unit.  
4. Rotate the VOLUME CONTROL (#1) to adjust to the desired output level.  
5. To turn off the radio, press the ON/OFF BUTTON (#12).  
TIPS FOR BEST RECEPTION  
AM – The AM antenna is located inside the cabinet of the unit. If AM reception is weak, change the position  
of unit until the internal antenna picks up the strongest signal.  
FM – During FM reception, always keep the FM WIRE ANTENNA (#21) fully extended for best performance.  
However, if FM reception is weak, try repositioning the unit until you get the best reception.  
USING THE LINE IN TO LISTEN TO EXTERNAL AUDIO PLAYER  
You may playback your favorite music from your iPod or a portable digital audio player using the Line in  
function.  
1. Connect the headphone jack of your external device to the LINE IN JACK (#18) at the rear cabinet of  
this unit using a stereo cord with a 3.5mm phone plug on either ends. (Note: the stereo cord is not  
included)  
2. Press the ON/OFF BUTTON (#12) to turn on the radio. It will automatically switch to Line In mode  
when a suitable stereo cord is correctly connected.  
3. Start playing your external audio device.  
4. Slowly increase the volume control of the unit until the desired level is obtained. To avoid output sound  
distortion due to overloading, you may need to lower the volume output of your audio device.  
Note: the stereo music from your audio device will be converted to a monaural audio output.  
5. Turn off your external audio device first when you finish listening.  
6. Then unplug the stereo cord from the LINE IN JACK (#18) and normal radio reception will resume.  
Note: If the unit is set for wake to radio but with an external player connected to the LINE IN JACK, it will revert  
to the beep alarm sound instead.  
DIMMER CONTROL  
MANUAL SETTING  
The display HI/LO DIMMER BUTTON (#19) is located on the back of the unit. Pressing it will toggle between  
bright and dim backlight options for the display.  
USING TALK ’N SET  
1. Start by saying the trigger word “Hello Clock Radio” or press the Snooze Bar (#11).  
2. The unit will reply “Yes” and will wait for your next command.  
3. Say “Display” and the unit will reply “Say Display Low or Display High”.  
4. Say “High” or “Low” to set the display brightness accordingly. You can also say the command  
“Cancel” and the display will stay at it’s current setting.  
5. If you do not say the command word correctly, the unit will prompt you to repeat or start all over again.  
RESETTING THE UNIT  
After you have installed backup batteries and connected the unit to AC power source for the first time, we  
recommend you to press the RESET Button (#15) at the bottom of the cabinet to correctly initialize it.  
In case of an erroneous display or prolonged abnormal behavior during normal use, you can also safely  
restore it to its factory preset conditions by pressing the RESET Button (#15). Please note that all personal  
settings including current time, alarm time and sleep session will be cleared. So, be sure to set up the clock  
again according to previous sections above.  
E-11  
 
Note: In very rare case (such as an electrostatic discharge on a dry cold winter day), if the unit still fails to reset  
after pressing the RESET Button, you should unplug it from the AC power and then remove the  
backup batteries from the battery compartment at the bottom of the unit for at least 10 minutes.  
SPECIFICATIONS  
Frequency Range:  
AM 530 - 1710 kHz  
FM 88 - 108 MHz  
AC Power Source:  
Backup Battery:  
Clock Accuracy:  
120V~ 60Hz 5W  
2 x 3V type CR2032 Lithium batteries (included)  
up to +/- 60 seconds per month  
CARE AND MAINTENANCE  
1. Children should be supervised when using this appliance.  
2. Never wrap the ac power cord around any animal or person. Special care should be taken with long wire.  
3. Clean your unit with a damp (never wet) cloth. Solvent or detergent should never be used.  
4. Avoid leaving your unit in direct sunlight or in hot, humid or dusty places.  
5. Keep your unit away from heating appliances and sources of electrical noise such as fluorescent lamps or  
motors.  
6. Always keep the microphone area clean and free from foreign matters for best voice recognition accuracy.  
TROUBLESHOOTING GUIDE  
Symptom  
Possible Cause  
Solution  
The clock does not  
recognize your voice  
commands correctly  
- Surrounding is too noisy.  
- Change to a quieter place or speak  
closer to the unit’s mic at louder  
voice.  
- The radio is playing.  
- Voice recognition is not designed to  
work in radio mode, you need to use  
manual settings instead.  
Talk ’N Set accidentally  
triggers without saying  
the trigger word  
- The unit is located in a noisy room  
or near a radio or TV.  
- Set the Trigger Switch (#3) to the  
OFF position to temporarily disables  
the Talk ’N Set feature.  
- Say “Cancel” if you hear the unit  
saying “Yes” on its own.  
Clock does not always  
recognize “Alarm Off”  
command during alarm  
and snooze  
- The surrounding is relatively noisy.  
- Your voice level is too low.  
- Repeat the command clearly at  
louder voice while facing the unit.  
Noise or distorted sound - Station not tuned properly for AM or - Retune the AM or FM broadcast  
on AM or FM broadcast  
FM.  
station.  
- FM: FM wire antenna is not  
extended.  
- FM: Fully extend FM wire antenna.  
- AM: The unit is not placed in best  
reception point.  
- AM: Reposition the unit until the best  
reception is obtained.  
AM or FM no sound  
- Unit not in “RADIO” function mode.  
- Volume set at minimum  
- Press On/Off Button until radio is on.  
- Increase Volume.  
- An external non playing digital audio - Unplug the line in cord  
player is connected to the line in  
jack  
Sound appears  
distorted at high volume  
setting  
- Volume control of this unit is set to  
maximum.  
- Adjust Volume Control to a lower  
comfortable level.  
LCD brightness is too  
dim  
- Display brightness set to dim mode  
- Set display brightness to HI manually  
or by Talk ’N Set command.  
E-12  
 
90 DAY LIMITED WARRANTY AND SERVICE  
VALID IN THE U.S.A ONLY  
SPECTRA MERCHANDISING INTERNATIONAL, INC. warrants this unit to be free from defective materials  
or factory workmanship for a period of 90 days from the date of original customer purchase and provided the  
product is utilized within the U.S.A. This warranty is not assignable or transferable. Our obligation under this  
warranty is the repair or replacement of the defective unit or any part thereof, except batteries, when it is  
returned to the SPECTRA Service Department, accompanied by proof of the date of original consumer  
purchase, such as a duplicated copy of a sales receipt. You must pay all shipping charges required to ship  
the product to SPECTRA for warranty service. If the product is repaired or replaced under warranty, the  
return charges will be at SPECTRA’s expense. There are no other express warranties other than those  
stated herein.  
This warranty is valid only in accordance with the conditions set forth below:  
1. The warranty applies to the SPECTRA product only while:  
a. It remains in the possession of the original purchaser and proof of purchase is demonstrated.  
b. It has not been subjected to accident, misuse, abuse, improper service, usage outside the  
descriptions and warnings covered within the owner’s manual or non-SPECTRA approved  
modifications.  
c. Claims are made within the warranty period.  
2. This warranty does not cover damage or equipment failure caused by electrical wiring not in compliance  
with electrical codes or SPECTRA owner’s manual specifications, or failure to provide reasonable care  
and necessary maintenance as outlined in the owner’s manual.  
3. Warranty of all SPECTRA products applies to residential use only and is void when products are used in a  
nonresidential environment or installed outside the United States.  
This warranty gives you specific legal rights, and you may also have other rights which vary from state to  
state. TO OBTAIN SERVICE, please remove all batteries (if any) and pack the unit carefully and send it  
prepaid by insured parcel post or UPS to SPECTRA at the address shown below. IF THE UNIT IS  
RETURNED WITHIN THE WARRANTY PERIOD shown above, please include a proof of purchase (dated  
cash register receipt) so that we may establish your eligibility for warranty service and repair of the unit  
without cost. Also include a note with a description explaining how the unit is defective. A customer service  
representative may need to contact you regarding the status of your repair, so include your name, address,  
phone number and e-mail address to speed the process.  
IF THE UNIT IS OUTSIDE THE WARRANTY PERIOD, please include a check for $15.00 to cover the cost  
of repair, handling and return postage. All out of warranty returns must be sent prepaid. It is recommended  
that you contact SPECTRA first at 1-800-777-5331 or by e-mail at [email protected] for updated  
information on the unit requiring service. In some cases the model you have may be discontinued and  
SPECTRA reserve the right to offer alternative options for repair or replacement.  
SPECTRA MERCHANDISING INTERNATIONAL, INC.  
4230 North Normandy Avenue,  
Chicago, IL60634, USA.  
1-800-777-5331  
To register your product, visit the link below on the website to enter your information.  
Printed in China  
E-13  
 

Indesit Oven FIE 56 KB GB 1 User Manual
JVC Camcorder DVL820 User Manual
JVC Car Stereo System GET0137 001A User Manual
JVC Car Stereo System KD A615 User Manual
JVC Flat Panel Television LT Z32SX4B User Manual
KitchenAid Dishwasher KDB 21B User Manual
KitchenAid Refrigerator KBCS24LSBS02 User Manual
Kodak Digital Camera Z612 User Manual
Kowa Inflatable Bouncy Toy fm600 User Manual
Kowa Saw VK 2 User Manual