Portable Speaker Station for iPod & iPhone
INSTRUCTION MANUAL
JiSS-250i
(iPod & iPhone not included)
Please read this Instruction Manual carefully before
using the unit and retain it for future reference
COMPLIANCE WITH FCC REGULATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
PROTECT YOUR FURNITURE!!
This system is equipped with non-skid rubber ‘feet’ to prevent the product from moving when you
operate the controls. These ‘feet’ are made from non-migrating rubber material specially formulated
to avoid leaving any marks or stains on your furniture. However certain types of oil based furniture
polishes, wood preservatives, or cleaning sprays may cause the rubber ‘feet’ to soften, and leave
marks or a rubber residue on the furniture.
To prevent any damage to your furniture we strongly recommend that you purchase small self-
adhesive felt pads, available at hardware stores and home improvement centers everywhere, and
apply these pads to the bottom of the rubber ‘feet’ before you place the product on fine wooden
furniture.
2
LOCATION OF CONTROLS
1
2
3
4
5
6
1.
2.
3.
4.
5.
6
7.
8.
9.
LEFT SPEAKER
Docking Tray
Docking Connector
RIGHT SPEAKER
STANDBY BUTTON
VOLUME +/- BUTTON
AUX IN JACK
DC IN JACK
FOLDABLE STAND
10. BATTERY DOOR
7
8
9
10
9
POWER SOURCE
This Portable Speaker System is designed to operate on 4 x 1.5V ‘AAA’ (UM-4) batteries (Not
included) or with the included AC Adaptor.
GETTING STARTED
A. DC OPERATION
For better performance and longer operating time, we recommend using alkaline-type batteries.
1. Remove the battery door on bottom of the cabinet.
2. Observe the polarity markings inside the compartment and install 4 x 1.5V ‘AAA’ (UM-4)
batteries correctly.
3. Replace the battery door.
.
IMPORTANT: Be sure that the battery is installed correctly. Wrong polarity may damage the unit.
BATTERY CARE
I.
Do not mix old and new batteries.
II.
Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.
III. If the unit is not to be used for an extended period of time, remove the battery. Any old or leaking
battery can cause damage to the unit and may void the warranty.
IV. Do not dispose batteries in fire. Batteries may leak or explode.
3
B. AC POWER CONNECTION
1. Plug the AC adaptor into a household 120V AC ~ 60Hz power source.
2. Insert the other plug into the DC INPUT Jack on the back of JiSS-250i.
Note: The batteries will be automatically disconnected once the AC adaptor is plugged into the DC
Jack and the System will operate on AC power.
iPod ADAPTORS
Below are the iPod Adaptors included in the package.
iPod classic
iPod touch
iPod Nano 2nd
Gen.
iPod nano 3rd
gen.
iPod Nano 4th
Gen.
iPhone
Note: No iPod adaptor is needed if you are using an iPod (5th generation) or iPod (4th generation).
4
DOCKING YOUR IPod
1. Fold out the STANDS located on the bottom of JiSS-250i.
2. Select a suitable adaptor attachment for your iPod/iPhone and insert it into the docking tray.
Your iPod/iPhone can now be inserted onto the dock connector by aligning the connector on
the bottom of the iPod onto the connector in the docking bay as shown below.
For iPod/iPhone Landscape Viewing (iPod nano (4th gen), iPod touch, iPhone 2G,
and iPhone 3G) proceed as below:
3. Choose the Correct adaptor to hold the iPod/iPhone and embed it at the iPod docking tray.
4. Extend the Speaker by pulling out the Left and Right Speaker
5. Insert the iPod firmly on the docking, now the iPod can be rotated freely into the Landscape
position to the Left as shown.
Note: - Please be careful when seating the iPod/iPhone into the docking to avoid damaging the
30-pin connector on the iPod or in the docking system.
-The iPod/iPhone will start charging immediately when it is docked.
- The iPod/iPhone will only be charged when the device is powered by an AC adaptor.
6. Turn the JiSS-250i on by pressing the STANDBY Button on the front panel.
7. Follow the iPod/iPhone operation instructions to operate your iPod/iPhone.
8. Adjust the sound level by pressing the VOL +/- buttons on the JiSS-250i.
Note: The volume level cannot be adjusted using the volume control on your iPod after docking.
9. To remove the iPod/iPhone from the unit, press and hold the PLAY/PAUSE Button for few
5
seconds to switch off the device and then gently remove it from the docking connector.
10. To turn JiSS-250i off, press the STANDBY Button again.
Note:
i.
The System will automatically enter sleep mode 5 minutes after playback stops and switch to
standby mode automatically after 30 minutes of no activity. In Sleep mode the LED will flash
and in standby mode, the LED will go off.
ii.
iii.
The AUX In function is in higher priority than the iPod function. Make sure the AUX IN Jack is
unplugged when you are going to enjoy the iPod music, otherwise the music of the iPod won’t
be heard.
Your iPod/iPhone will only be charged when the System is powered by AC.
AUX IN OPERATION
You can play other music sources (MP3 or other digital audio players) through the speakers of this
System by connecting the AUX IN Jack to your external player’s audio out jack or headphone jack.
1.
2.
To turn the JiSS-250i on, press the STANDBY Button on the front panel.
Plug one end of an audio cable (included) into the AUX IN Jack and the other end of the cable
into the headphone jack of your digital audio player.
3.
4.
Start playing the device plugged into the AUX IN jack.
Adjust both the volume controls on the JiSS-250i and your external player for a comfortable
listening level.
5.
Turn off your external player when you have finished listening. Turn the JiSS-250i off and
unplug the AUX IN jack.
CARE AND MAINTENANCE
1. Avoid operating your unit under direct sunlight or in hot, humid or dusty places.
2. Keep your unit away from heating appliances and sources of electrical noise such as fluorescent
lamps or motors.
3. For better Display clarity, avoid operating the unit under direct sunlight or in strong room
illumination.
4. Unplug the unit from the electrical power outlet immediately in case of malfunction.
6
TROUBLESHOOTING GUIDE
Should you experience any difficulties in the use of this player please refer to the following chart or
call 1 800 777 5331 for Product Service and Support.
Symptom
Possible Problem
Solution
Cannot dock iPod Using a wrong iPod adaptor Make sure the adaptor properly fits for your iPod.
properly
iPod is not installed
properly.
Remove your iPod from the dock and check for any
obstruction on the connectors in the dock and on your
iPod, then reseat it in the dock.
iPod does not
respond to the unit. properly.
iPod is not installed
Remove your iPod from the dock and check for any
obstruction on the connectors in the dock and on your
iPod, then reseat in the dock.
Your iPod software is too
Update software on your iPod. For details, please visit
Unplug the audio connection cable.
old
No sound when AUX IN Jack is plugged
iPod plays
No sound from
speaker in AUX
mode
Input source is low
Increase the volume level on the audio source device.
Switch on the power of the external source.
Power to external source
(MP3, Laptop etc) not
switched on.
No sound when
played in the AUX
Mode
Master Volume is at
minimum.
Adjust the master volume
Too much distortion
Batteries are low. change
the New Batteries
Replace all batteries by fresh ones.
SERVICE
Please refer to the instructions on the enclosed warranty card for returning your unit for service.
When returning the unit, please remove any batteries to prevent damage to the unit in transit and/or
from possible battery leakage. Please note that we are not responsible for batteries returned with
the unit or for the cost of replacement of batteries.
Distributed by:
Spectra Merchandising International, Inc.
4230 North Normandy Avenue
Chicago IL 60634, U.S.A.
Please have model number ready, for Customer service, call 1-800-777-5331
iPod is a trademark of Apple Inc., registered in the U.S. and other countries.
iPhone is a trademark of Apple Inc.
"Made for iPod" means that an electronic accessory has been designed to connect specifically to
iPod and has been certified by the developer to meet Apple performance standards.
"Works With iPhone" means that an electronic accessory has been designed to connect specifically
to iPhone and has been certified by the developer to meet Apple performance standards.
Apple is not responsible for the operation of this devise or its compliance with safety and regulatory
standards.
Printed in China
7
|