JLLFW1602
Fridge
Instruction manual
• The appliance is intended for keeping
foodstuff and/or beverages in a normal
household as explained in this instruction
booklet.
power plug may overheat and cause a
fire.
3. Make sure that you can come to the
mains plug of the appliance.
• Do not use a mechanical device or any
artificial means to speed up the thawing
process.
4. Do not pull the mains cable.
5. If the power plug socket is loose, do
not insert the power plug. There is a
risk of electric shock or fire.
• Do not use other electrical appliances
(such as ice cream makers) inside of
refrigerating appliances, unless they are
approved for this purpose by the
manufacturer.
6. You must not operate the appliance
without the lamp cover of interior
lighting.
• This appliance is heavy. Care should be
taken when moving it.
• Do not damage the refrigerant circuit.
• The refrigerant isobutane (R600a) is
contained within the refrigerant circuit of
the appliance, a natural gas with a high
level of environmental compatibility,
which is nevertheless flammable.
During transportation and installation of
the appliance, be certain that none of the
components of the refrigerant circuit
become damaged.
• Do not remove nor touch items from the
freezer compartment if your hands are
damp/wet, as this could cause skin
abrasions or frost/freezer burns.
• Avoid prolonged exposure of the
appliance to direct sunlight.
• Bulb lamps used in this appliance are
special purpose lamps selected for
household appliances use only. They are
not suitable for household room
illumination.
If the refrigerant circuit should become
damaged:
– avoid open flames and sources of
ignition
– thoroughly ventilate the room in which
the appliance is situated
• It is dangerous to alter the specifications
or modify this product in any way. Any
damage to the cord may cause a short-
circuit, fire and/or electric shock.
Daily Use
• Do not place hot items such as pans and
baking trays near the plastic components
of the appliance.
• Do not store flammable gas and liquid in
the appliance, because they may explode.
• Do not place food products directly
against the air outlet on the rear wall.1)
• Frozen food must not be re-frozen once it
has been thawed out.
Warning! Any electrical component
(power cord, plug, compressor) must
be replaced Service Force agent.
1. Power cord must not be lengthened.
• Store pre-packed frozen food in
accordance with the frozen food
manufacturer's instructions.
2. Make sure that the power plug is not
squashed or damaged by the back of
the appliance. A squashed or damaged
1) If the appliance is Frost Free
3
• Appliance's manufacturers storage
recommendations should be strictly
adhered to. Refer to relevant instructions.
• Please refer to the correct positioning and
location instructions that can be found in
the Installation section of this user guide.
• Do not place carbonated or fizzy drinks in • The appliance must not be located close
the freezer compartment as it creates
pressure on the container, which may
cause it to explode, resulting in damage to
the appliance.
to radiators or cookers.
• Make sure that the mains plug is
accessible after the installation of the
appliance.
• Ice lollies can cause frost burns if
consumed straight from the appliance.
Service
• Any electrical work required to do the
servicing of the appliance should be
carried out by a qualified electrician or
competent person.
Care and cleaning
• Before maintenance, switch off the
appliance and disconnect the mains plug
from the mains socket.
• Do not clean the appliance with metal
objects.
• This product must be serviced by an
authorised Service Centre, and only
genuine spare parts must be used.
• Do not use sharp objects to remove frost
from the appliance. Use a plastic scraper.
Environment Protection
• Regularly examine the drain in the
refrigerator for defrosted water. If
necessary, clean the drain. If the drain is
blocked, water will collect in the bottom
of the appliance.
This appliance does not contain
gasses which could damage the
ozone layer, in either its refrigerant
circuit or insulation materials. The
appliance shall not be discarded
together with the urban refuse and
rubbish. The insulation foam contains
flammable gases: the appliance shall
be disposed according to the
Installation
Important! For electrical connection
carefully follow the instructions given in
specific paragraphs.
applicable regulations to obtain from
your local authorities. Avoid
damaging the cooling unit, especially
at the rear near the heat exchanger.
The materials used on this appliance
marked by the symbol are
recyclable.
• Unpack the appliance and check if there
are damages on it. Do not connect the
appliance if it is damaged. Report possible
damages immediately to the place you
bought it. In that case retain packing.
• It is advisable to wait at least four hours
before connecting the appliance to allow
the oil to flow back in the compressor.
• In order to prevent over heating there
must be adequate circulation around the
appliance.
4
Contents
For the user
For the installer
Safety information
2
Technical Information 15
Control Panel
Display
Switching on
6
6
6
6
6
7
7
7
7
7
Installation
Location
Levelling
15
15
16
16
16
17
17
Switching off
Positioning
Temperature regulation
Functions Menu
Eco Mode Function
Shopping Function
Child Lock Function
Holiday Function "H"
Electrical Connection
Rear spacers
Door reversibility
First use
Cleaning the interior
8
8
Daily use
8
8
8
9
9
9
Use of the fridge compartment
Movable shelves
Guide to use the
instruction
manual
Vegetable Drawer
Bottle rack
Positioning the door shelves
Helpful hints and tips
Hints for energy saving
Hints for fresh food refrigeration
Hints for refrigeration
9
10
10
10
The following symbols will be
found in the text to guide you
throughout the instructions:
Safety instructions
Hints and tips
Care and Cleaning
Periodic cleaning
Defrosting of the refrigerator
Periods of non-operation
10
10
11
11
What to do if…
Replacing the lamp
12
14
Environmental
information
5
Control Panel
A B
C
D E
A - Appliance button ON/OFF
D - Function button
B - Temperature regulation button
C - Temperature and function indicator
E - Confirmation button
Display
If on the Eco Mode function is on
Positive Temperature indicator
Temperature indicator
If on the Shopping function is on
If on the Child Lock function is on
Switching on
Insert the plug into the power outlet. If the
display is not illuminated, press button (A),
to start the appliance.
Switching off
The appliance is shut off by pressing key (A)
for more than 1 second.
During this, a countdown of the
For optimal food storage select the Eco
Mode and the temperature is set to +5°C in
the fridge.
To select a different temperature refer to
"Temperature regulation".
temperature from -3 -2 -1 will be shown.
Temperature regulation
The temperature may be changed by
pressing the button (B).
The current temperature setting flashes and
by pressing button (B) again the set
temperature is possible to change in steps of
one degree.
After some seconds is shown the set default
temperature.
Important! If the door remains open for
some minutes, the light will turn off
automatically. The light is reset by closing
and opening the door itself.
6
The Shopping function shuts off
automatically after approximately 6 hours. It
is possible to de-activate the function at any
time by pressing key (D) until the
corresponding icon will flash and then key
(E).
Functions Menu
By activating the key D the functions menu is
operating. Each function could be confirmed
by pressing button E. If there is no
confirmation after some seconds the display
will go out from the menu and return in
normal condition. The following functions
are indicated:
Child Lock Function
The Child Lock function is activated by
pressing key (D) (several times if necessary)
Eco Mode function
Shopping function
Child Lock function
until the corresponding icon appears
.
You must confirm the choice by pressing key
(E) within few seconds. You will hear the
buzzer and the icon remains lighted. In this
condition any possible operation through
the keys does not cause any change as long
as this function is activated.
It is possible to de-activate the function at
any time by pressing key (D) until the
corresponding icon will flash and then key
(E).
Eco Mode Function
The Eco Mode function is activated by
pressing key D (several times if necessary)
until the corresponding icon appears
setting the temperature at +5°C).
You must confirm the choice by pressing key
E within few seconds. You will hear the
buzzer and the icon remains lighted.
In this condition the chosen temperatures
are automatically set (+ 5°C), in the best
conditions for storing food.
(or
Holiday Function "H"
The holiday function sets the temperature at
+ 15°C.
It is possible to de-activate the function at
any time by changing the selected
temperature in the compartment.
This function allows you to keep the
refrigerator shut and empty during a long
holiday period ( e. g. the summer holidays)
without the formation of a bad smell.
To turn on the holiday function operate as
per modift the selected temperature. The
temperature indicator can modify the
displayed temperature up to + 8 °C, 1 °at a
tim. + 2 °C will be followed by the letter "H
". Press key E to confirm.
Shopping Function
If you need to insert a large amount of warm
food, for example after doing the grocery
shopping, we suggest activating the Shopping
function to chill the products more rapidly
and to avoid warming the other food which
is already in the refrigerator.
Now the refrigerator is in the "holiday
"function in the energy- saving mode.
The Shopping function is activated by
pressing key (D) (several times if necessary)
Important! The fridge compartment must
be empty with holiday function on.
until the corresponding icon appears
.
You must confirm the choise by pressing key
(E) within few seconds. You will hear the
buzzer and the icon remains lighted.
7
First use
Important! Do not use detergents or
abrasive powders, as these will damage the
finish.
Cleaning the interior
Before using the appliance for the first time,
wash the interior and all internal accessories
with lukewarm water and some neutral soap
so as to remove the typical smell of a brand-
new product, then dry thoroughly.
Daily use
Important! If the ambient temperature is
high or the appliance is fully loaded, and the
appliance is set to the lowest temperatures,
it may run continuously causing frost to form
on the rear wall. In this case the
Temperature regulator must be set to a
higher temperature to allow automatic
defrosting and therefore reduced energy
consumption.
Use of the fridge
compartment
The temperature of this compartment may
be regulated between +2°C and +8°C.
During normal functioning the indicator
shows the temperature inside the fridge.
A medium setting is generally the
most suitable.
The exact setting should be chosen keeping
in mind that the temperature inside the
appliance depends on:
Movable shelves
The walls of the refrigerator are equipped
with a series of runners so that the shelves
can be positioned as desired.
• room temperature
• how often the door is opened
• the quantity of food stored
• the location of the appliance.
8
Bottle rack
Place the bottles (with the opening facing
front) in the pre-positioned shelf.
Important! If the shelf is positioned
horizontally, place only closed bottles.
This bottle holder shelf can be tilted in order
to store previously opened bottles. To
obtain this result, pull the shelf up so it can
rotate upwards and be placed on the next
higher level.
Important!
Do not move the glass shelf above the
vegetable drawer to ensure correct air
circulation
Vegetable Drawer
The drawer is suitable for storing fruit and
vegetables.
Some models have a separator inside the
drawer that can be placed in different
positions to allow for the subdivision best
suited to personal needs.
Positioning the door
shelves
To permit storage of food packages of
various sizes, the door shelves can be placed
at different heights.
All parts inside the drawer can be removed
for cleaning purposes.
Helpful hints and tips
is not a fault with the appliance and is a
completely normal operating sound.
Normal Operating
Sounds
• You may hear a faint gurgling and a
bubbling sound when the refrigerant is
pumped through the coils or tubing. This
• When the compressor is on, the
refrigerant is being pumped around and
you will hear a whirring sound and a
pulsating noise from the compressor. This
is correct.
9
• The thermic dilatation might cause a
sudden cracking noise. This is not a fault
with the appliance and is a completely
normal operating sound.
• position food so that air can circulate
freely around it
Hints for refrigeration
Useful hints:
Meat (all types) : wrap in polythene bags and
place on the glass shelf above the vegetable
drawer.
Hints for energy saving
• Do not open the door frequently or leave
it open longer than absolutely necessary.
For safety, store in this way only one or two
days at the most.
Cooked foods, cold dishes, etc..: these
should be covered and may be placed on
any shelf.
Fruit and vegetables: these should be
thoroughly cleaned and placed in the special
drawer(s) provided.
Butter and cheese: these should be placed in
special airtight containers or wrapped in
aluminium foil or polythene bags to exclude
as much air as possible.
• If the ambient temperature is high and the
Temperature Regulator is set to low
temperature and the appliance is fully
loaded, the compressor may run
continuously, causing frost or ice on the
evaporator. If this happens, set the
Temperature Regulator toward warmer
settings to allow automatic defrosting and
so a saving in electricity consumption.
Hints for fresh food
refrigeration
Milk bottles: these should have a cap and
should be stored in the bottle rack on the
door.
Bananas, potatoes, onions and garlic, if not
packed, must not be kept in the refrigerator.
To obtain the best performance:
• do not store warm food or evaporating
liquids in the refrigerator
• do cover or wrap the food, particularly if
it has a strong flavour
Care and Cleaning
• clean the inside and accessories with
lukewarm water and some neutral soap.
Caution! Unplug the appliance
before carrying out any maintenance
operation.
• regularly check the door seals and wipe
clean to ensure they are clean and free
from debris.
This appliance contains hydrocarbons
in its cooling unit; maintenance and
recharging must therefore only be
carried out by authorised technicians.
• rinse and dry thoroughly.
Periodic cleaning
The equipment has to be cleaned regularly:
10
Important! Do not pull, move or damage
any pipes and/or cables inside the cabinet.
Never use detergents, abrasive powders,
highly perfumed cleaning products or wax
polishes to clean the interior as this will
damage the surface and leave a strong
odour.
Clean the condenser (black grill) and the
compressor at the back of the appliance
with a brush or a vacuum cleaner. This
operation will improve the performance of
the appliance and save electricity
consumption.
It is important to periodically clean the
defrost water drain hole in the middle of the
refrigerator compartment channel to
prevent the water overflowing and dripping
onto the food inside. Use the special cleaner
provided, which you will find already
inserted into the drain hole.
Important! Take care of not to damage
the cooling system.
Many proprietary kitchen surface cleaners
contain chemicals that can attack/damage
the plastics used in this appliance. For this
reason it is recommended that the outer
casing of this appliance is only cleaned with
warm water with a little washing-up liquid
added.
Periods of non-operation
When the appliance is not in use for long
periods, take the following precautions:
After cleaning, reconnect the equipment to
the mains supply.
• disconnect the appliance from
electricity supply
• remove all food
defrost2) and clean the appliance and all
accessories
• leave the door/doors ajar to prevent
unpleasant smells.
If the cabinet will be kept on, ask somebody
to check it once in a while to prevent the
food inside from spoiling in case of a power
failure.
Defrosting of the
refrigerator
Frost is automatically eliminated from the
evaporator of the refrigerator compartment
every time the motor compressor stops,
during normal use. The defrost water drains
out through a trough into a special container
at the back of the appliance, over the motor
compressor, where it evaporates.
•
2) If foreseen.
Download from Www.Somanuals.c1om1. All Manuals Search And Download.
What to do if…
During operation of the appliance some
smaller but annoying trouble can often
occur, which does not require calling a
technician out. In the following chart
information is given about them to avoid
unnecessary charges on service.
Important! The appliance operates
discontinuously, so the stopping of
compressor does not mean being no
current. That is why you must not touch the
electrical parts of the appliance before
breaking the circuit.
Important! The operation of the appliance
goes with certain sounds (compressor and
circulating sound). This not means a trouble,
but a normal operation.
Problem
Possible cause
Solution
The appliance is noisy.
The appliance is not supported
properly.
Check if the appliance stands
stable (all feet and wheels should
be on the floor). Refer to
"Levelling".
The spacers located between the Put them back in place again.
back of the cabinet and the pipes
come loose.
An error has occurred in
measuring the temperature
Call your service representative
(the cooling system will continue
to keep food products cold, but
temperature adjustment will not
be possible)
is displayed in the
temperature display
The compressor
operates continually.
The Temperature regulator may Set a warmer temperature.
be set incorrectly.
The door is not closed correctly. Refer to "Closing the door".
The door has been opened too
frequently.
Do not keep the door open
longer than necessary.
The food temperature is too
high.
Let the food temperature
decrease to room temperature
before storage.
The room temperature is too
high.
Decrease the room temperature.
Water flows on the rear During the automatic defrosting This is correct.
plate of the
refrigerator.
process, frost defrosts on the
rear plate.
12
Problem
Possible cause
Solution
Water flows into the
refrigerator.
The water outlet is clogged.
Clean the water outlet.
Food prevent that water flows
into the water collector.
Make sure that food do not touch
the rear plate.
Water flows on the
ground.
The melting water outlet does
not flow in the evaporative tray
above the compressor.
Attach the melting water outlet to
the evaporative tray.
There is too much frost Food are not wrapped properly. Wrap the food better.
and ice.
The door is not closed correctly. Refer to "Closing the door".
The Temperature regulator may Set a higher temperature.
be set incorrectly.
The temperature in the The Temperature regulator may Set a higher temperature.
appliance is too low.
be set incorrectly.
The temperature in the The Temperature regulator may Set a lower temperature.
appliance is too high.
be set incorrectly.
The door is not closed correctly. Refer to "Closing the door".
The food temperature is too
high.
Let the food temperature
decrease to room temperature
before storage.
The temperature in the There is no cold air circulation in Make sure that there is cold air
refrigeration is too high. the appliance.
circulation in the appliance.
Large quantities of food to be
cooled were put in at the same
time.
Insert smaller quantities of food to
be cooled at the same time.
The appliance does not The appliance is switched off.
Switch on the appliance.
operate.
The mains plug is not connected Connect the mains plug to the
to the mains socket correctly.
mains socket correctly.
The appliance has no power.
Connect a another electrical
There is no voltage in the mains appliance to the mains socket.
socket.
Check fuse. Contact a qualified
electrician.
The lamp does not
work.
The lamp is in stand-by.
Close and open the door.
The door has been open to long. Close the door.
The lamp is defective. Refer to "Replacing the lamp".
Download from Www.Somanuals.c1om3. All Manuals Search And Download.
As much as the advice does not lead to result, call the nearest brand-mark service.
Replacing the lamp
1. Disconnect the mains plug from the
mains socket.
2. Press on the rear hook and at the same
time slide the lamp cover in the direction
of the arrow.
3. Replace the lamp with one of the same
power and specifically designed for
household appliances. (the maximum
power is shown on the light lamp cover)
4. Install the lamp cover by sliding it into its
original position.
5. Connect the mains plug to the mains
socket.
6. Open the door. Make sure that the lamp
comes on.
Closing the door
1. Clean the door gaskets.
2. If necessary, adjust the door. Refer to
"Installation".
3. If necessary, replace the defective door
gaskets. Contact the Service Force
Centre.
14
Technical Information
Dimension
Height
Width
Depth
1600 mm
600 mm
650 mm
230-240 V V
50 Hz
Voltage
Frequency
The technical information are situated in the
rating plate on the internal left side of the
appliance and in the energy label.
Installation
Read the "Safety Information"
carefully for your safety and correct
operation of the appliance before
installing the appliance.
50mm
Location
To ensure best performance, if the appliance
is positioned below an overhanging wall unit,
the minimum distance between the top of
the cabinet and the wall unit must be at least
40 mm . Ideally, however, the appliance
should not be positioned below overhanging
wall units.
If the cabinet is placed in a corner and the
side with the hinges facing the wall, the
distance between the wall and the cabinet
must be at least 10 mm to allow the door to
open enough so that the equipment can be
removed.
The ventilation space can be:
• directly above the appliance
• behind and above the top cupboard.
In this case, the space behind the top
cupboard must be at least 50 mm deep.
Download from Www.Somanuals.c1om5. All Manuals Search And Download.
Levelling
When placing the appliance ensure that it
stands level. This can be achieved by two
adjustable feet at the bottom in front.
Climate Ambient temperature
class
N
ST
T
+16°C to + 32°C
+16°C to + 38°C
+16°C to + 43°C
Electrical Connection
Caution! Any electrical work
required to install this appliance
should be carried out by a qualified
electrician or competent person.
Warning! This appliance must be
earthed.
The manufacturer declines any
liability should these safety measures
not be observed.
Important! The wires in the mains lead are
coloured in accordance with the following
code:
Positioning
GREEN & YELLOW
13 AMP. FUSE
Warning! If you are discarding an
old appliance that has a lock or catch
on the door, you must ensure that it
is made unusable to prevent young
children being trapped inside.
Important! The appliance should have the
plug accessible after installation.
BROWN
Install this appliance at a location where the
ambient temperature corresponds to the
climate class indicated on the rating plate of
the appliance:
BLUE
CORD CLAMP
Green and Yellow:
Brown:
Earth
Live
1
3
5
Climate Ambient temperature
class
Blue:
Neutral
SN
+10°C to + 32°C
16
As the colours of the wires in the mains lead
of this appliance may not correspond with
the coloured markings identifying the
terminals in your plug, proceed as follows:
1. Connect the wire coloured green and
yellow to the terminal marked either
with the letter “E“ or by the earth
symbol or coloured green and yellow.
2. Connect the wire coloured blue to the
terminal either marked with the letter
“N“ or coloured black.
3. Connect the wire coloured brown to
the terminal either marked with the
“L“ or coloured red.
4. Check that no cut, or stray strands of
wire is present and the cord clamp
secure over the outer sheath.
4
is
5. Make sure the electricity supply voltage
is the same as that indicated on the
appliance rating plate.
6. Switch on the appliance.
The appliance is supplied with a 13 amp plug
Slacken the screws and insert the spacer
under the screw head, then retighten the
screws.
fitted
2
. In the event of having to change
the fuse in the plug supplied, a 13 amp ASTA
approved (BS 1362) fuse must be used.
Door reversibility
Warning! A cut off plug inserted
into a 13 amp socket is a serious
safety (shock) hazard. Ensure that it is
disposed of safely.
Warning! Before carrying out any
operations, remove the plug from the
power socket.
To carry out the following operations, we
suggest that this be made with another
person that will keep a firm hold on the
door of the appliance during the operations.
Gently lay the appliance on its back.
To change the opening direction of the
door, do these steps:
Rear spacers
Inside the appliance you find two
spacers which must be fitted as shown
in the figure.
1. Remove the clip-in ventilation grille,
remove the plug (e) from the ventilation
grille and install it on the opposite side.
2. Remove the bottom hinge (A) by
unscrewing the fixing screws.
Download from Www.Somanuals.c1om7. All Manuals Search And Download.
accessory bag the two plugs and cover
the holes left open after having
removed the handle.
f
A
A
e
3. Remove the door.
4. Unscrew the pin (f) of the bottom hinge
and install it on the opposite side.
5. Unscrew the pin of the upper hinge and
install it on the opposite side.
9. Make sure that the front board of the
door is parallel to the front board of the
top.
10. Reposition, level the appliance, wait for
at least four hours and then connect it
to the power socket.
Do a final check to make sure that:
• All screws are tightened.
• The magnetic seal adheres to the cabinet.
• The door opens and closes correctly.
If the ambient temperature is cold (i.e. in
Winter), the gasket may not fit perfectly to
the cabinet. In that case, wait for the natural
fitting of the gasket.
6. Install the door in the upper hinge.
7. Install the ventilation grille, clipping it
into place.
8. Unscrew the handle. Remove the plug
with a punch. Install the handle and the
plug on opposite side. Take from the
Repairs-After Sales Service
If the unlikely event of your appliance
requiring service, or if you wish to purchase
spare parts, please contact our extended
warranty administrators by telephoning:
0870 010 7887
They will give you details of your local
Service Force Centre.
18
Before calling out an engineer, please ensure S.No. : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
you have read the details under the heading
''What to do if''.
. . . .
Your appliance is covered by a 3 year parts
and labour guarantee (see separate details
given at point of sale). Please retain your
purchase receipt safely for the service
engineer to verify the purchase details.
When you contact your local repair agent
you will need to give the following details:
1. Your name, address and post code.
2. Your telephone number.
3. Clear and concise details of fault.
Spare parts
4. The purchase date (found on your
receipt).
An authorised service engineer should
service this product and only genuine spare
parts should be used.
5. The model and serial number of the
appliance (found on the rating plate).
So that you always have these numbers at
hand, we recommend that you make a note
of them here:
Mod. : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . .
PNC : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . .
Under no circumstances should you attempt
to repair the machine yourself. Repairs
carried out by inexperienced persons may
cause injury or serious malfunctioning.
Contact your local repair agent by
telephoning:
0870 010 7887
Environmental concerns
The symbol on the product or on its
packaging indicates that this product may
not be treated as household waste. Instead
it should be taken to the appropriate
collection point for the recycling of electrical
and electronic equipment. By ensuring this
product is disposed of correctly, you will
help prevent potential negative
consequences for the environment and
human health, which could otherwise be
caused by inappropriate waste handling of
this product. For more detailed information
about recycling of this product, please
contact your local council, your household
waste disposal service or the shop where
you purchased the product.
Download from Www.Somanuals.c1om9. All Manuals Search And Download.
|