COMPONENT
#840271
1/2" VARIABLE SPEED ELECTRIC
HAMMER DRILL
INSTRUCTION MANUAL
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION,
MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND
UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS. FAILURE
TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.
FOR CUSTOMER SERVICE
POUR LE SERVICE APRÉS VENTE
OU DU CONSOMMATEUR
IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE
PRODUCT, DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER
SERVICE DEPARTMENT AT 1-800-590-3723. BEFORE YOU CALL, HAVE THE FOLLOWING
INFORMATION AVAILABLE: MODEL NO., DATE PURCHASED AND STORE LOCATION. AN
ALLTRADE REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU
WOULD LIKE TO MAKE A SUGGESTION OR COMMENT, GIVE US A CALL OR EMAIL US AT:
INFO@ALLTRADETOOLS.COM. YOUR FEEDBACK IS VITAL TO US.
87-1904-60957
KAWASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™ MOTORS CORP.,
U.S.A., WHICH DOES NOT MANUFACTURE OR DISTRIBUTE THIS PRODUCT.
CONSUMER INQUIRES SHOULD BE DIRECTED TO:
PARA EL SERVICIO
PARA EL CONSUMIDOR
©COPYRIGHT 2007 ALLTRADE TOOLS, LLC.
1431 VIA PLATA
1-800-590-3723
LONG BEACH, CA 90810-1462 USA
Printed in China
840271 – 1/2" Variable Speed Hammer-Drill_Rev 3/26/07
WORK AREA
CAUTION
indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury.
Keep your work area clean and well lit.
areas may cause accidents or injury.
Cluttered work benches and dark work
CAUTION
used without the safety alert symbol
indicates a potentially hazardous situation which,
if not avoided, may result in property damage.
Do not operate power tools in explosive areas, such as in the presence of
flammable liquids, gases or dust.
the dust or fumes.
Power tools create sparks which may ignite
NOTE
provides additional information that is useful
for proper use and maintenance of this tool. If a
NOTE is indicated make sure it is fully understood.
Keep bystanders, children and visitoors away while operating a power tool.
Distractions can cause you to lose control.
IMPORTANT SAFEGUARDS
ELECTRICAL SAFETY
Double insulated tools are equipped with a polarized plug (one blade is
wider than the other.) This plug will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician to installl a polarized outlet. Do not change the
People with electronic devices, such as pacemakers, should consult their
physician(s) before using this product. Operation of electrical equipment in
close proximity to a heart pacemaker could cause interference or failure of
the pacemaker.
plug in any way.
Double insulation eliminates the need for the three wire
grounded power cord and grounded power supply system.
WARNING:
Some dust created by power sanding, sawing, grinding, drilling and
other construction activities contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm.
Avoid body contact with grounded surfaces such as pipes, radiators, ranges and
refrigerators
. There is an increased risk of electric shock if your body is grounded.
Some examples of these chemicals are:
• Lead from lead-based paints.
Don’t expose power tools to rain or wet conditions.
tool will increase the risk of electric shock.
Water entering a power
• Crystalline silica from bricks and cement and other masonry products,
and arsenic and chromium from chemically-treated lumber.
Do not abuse the cord. Never use the cord to carry the tool or pull the plug
from an outlet. KKeep the cord away from heat, oil, sharp edges, or moving
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as dust masks that are
specially designed to filter out microscopic particles.
parts. Replace damaged cords immediately
. Damaged cords increase the risk
of electric shock.
When operating the tool outside, use an outdoor extension cord marked “W-A”
or “W.”
These cords are rated for outdoor use and reduce the risk of electric shock.
WARNING:
Handling the power cord on this product may expose you to lead, a
chemical known to the State of California to cause cancer and birth defects or
other reproductive harm. Wash hands after handling.
PERSONAL SAFETY
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Stay alert, watch what you are doing, and use common sense when operat-
ing a power tool. Do not use tool while tired or under the influence of drugs,
alcohol or medication.
A moment of inattention while operating power tools
may result in serious personal injury.
3
4
SERVICE
Tool service must be performed only by qualified repair personnel.
maintenance by unqualified personnel could result in a risk of injury.
Service or
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts.
jewelry or long hair can be caught in moving parts.
Loose clothes,
When servicing a tool, use only identical replacement parts. Follow instructions
in the Maintenance section of this manual.
Use of unauthorized parts or failure to
Avoid accidental starting. Be sure switch is off before plugging in
. Carrying tools with
follow Maintenance Instructions may create a risk of shock or injury.
your finger on the switch or plugging in tools that have the switch on invites accidents.
Remove adjusting keys or wrenches before turning the power tool “ON”.
A wrench or a key that is left attached to a rotating part of the power tool may
result in personal injury.
SPECIFIC SAFETY RULES AND/OR SYMBOLS
Hold tool by insulated gripping surfaces when perform-
ing an operation where the cutting tool may contact hidden wiring.
with a “live” wire will also make exposed metal parts of the tool “live” and shock
the operator.
Do not overreach. Keep proper footing and balance at all times.
Proper footing
and balance enables better control of the power tool in unexpected situations.
Use safety equipment. Always wear eye protection.
Contact
Dust mask, non-skid
safety shoes, hard hat or hearing protection must be used for appropriate
conditions.
IMPORTANT SAFETY RULES FOR HAMMER DRILLS
TOOL USE AND CARE
This tool is supplied with a fitted electrical plug.
Do not use an extension cord or
replacement electrical plug. Replace damaged or worn power cords immediately.
For safety and better control, always use both hands to hold tool.
Use clamps or other practical ways to secure and support the workpiece to a
If the bit jams
and kicks back, having both hands on the drill will make it easier to handle.
Always use the side handles supplied with the tool.
stablle platform.
Holding the work by hand or against your body is unstable and
may lead to loss of control.
Keep a firm grip on the tool
at all times. Do not attempt to operate this tool without holding it in both hands.
Do not force tool. Use the correct tool for your application.
The correct tool
will do the job better and safer at the rate for which it is designed.
Always wear eye protection and an OSHA-approved dust mask when drilling.
Do not use the tool if the power switch does not turn it “ON” or “OFF”. Any tool
that cannot be controlled with the switch is dangerous and must be repaired.
Wear safety goggles or other eye protection.
Hammering and drilling opera-
tions cause chips to fly. Flying particles can cause permanent eye damage.
Disconnect the power cord plug from the power source before making any
Wear ear protection when hammering for extended periods of time.
Temporary hearing loss or serious drum damage may result from high sound
levels generated by hammer drilling.
adjustments, changing accessories or storing the tool.
Such preventive safe-
ty measures reduce the risk of starting the tool accidentally.
Store idle tools oout of reach of children and other untrained persons.
are dangerous in the hands of untrained users.
Tools
Never hold the work piece in your hand or against your body.
the work piece to a stable base. Never drill material too small to be secured properly.
Use clamps to anchor
Never run the drill while carrying it at your side.
Maintain tools with care. Keep cutting tools sharp and clean.
Properly maintained
tools with a sharp cutting edge are less likely to bind and are easier to control.
Keep hands and drill cord away from the rotating bit.
Check for misalignment or binding of moving parts, breakage of parts, and
Make sure there are no nails, staples or other foreign objects in the work piece
.
any oother condition that may affect the tool’s operation.
tool serviced before using.
If damaged, have the
To prevent accidental starting, always disconnect the plug from the power source
before making any adjustments or changing accessories.
Use only accessories that are recommended by the manufacturer for your
model.
Accessories that may be suitable for one tool, may become hazardous
when used on another tool.
6
FUNCTIONAL DESCRIPTION
8
If the bit becomes bound in the work piece, release the trigger immediately
and prepare for the tooll to kickback toward you.
Reverse the direction of rota-
tion, then back out the bit by slowly squeezing the trigger.
1
Make sure all accessories are rated for the recommended speed of the drill.
Brushes, grinding wheels and other accessories may fall apart if run at too high
a speed, sending dangerous debris flying at the operator.
3
7
5
2
Never wear gloves when operating the drill.
hot bits and accessories to avoid burns.
Use gloves only when changing
6
4
Hammer bits and tools get hot during operation.
Wear gloves when touching them.
DDo not use in damp or wet locations. Do not operate tool in an explosive
atmosphere
11
, such as in the presence of flammable liquids, gases or dust.
9
Power tools create sparks, which may cause an explosion or fire.
10
SYMBOLS
IMPORTANT:
Some of the following symbols may be used on your tool. Please
study them and learn their meaning. Proper interpretation of these symbols will
allow you to operate the tool better and safer.
12
SYMBOL
NAME
EXPLANATION
Voltage (Potential)
Current
Frequency (Cycles per Second)
Power
Weight
Type of Current
Type of Current
CONTROLS AND COMPONENTS:
1. 1/2" Variable Speed Hammer-Drill
V
A
Hz
W
Kg
Volts
Amperes
Hertz
10. Chuck Key
2. 13mm (1/2") Chuck
3. Speed Control Adjusting Switch
4. On/Off Switch
11. Chuck Key Holder
12. Power Cord
Watt
Kilograms
Alternating Current
Direct Current
5. Lock-On Switch
6. Forward/Reversing Switch Lever
7. Adjustable Side Handle
8. Hammer/Drill Selector
9. Depth Gauge
Alternating or Direct Current Type of Current
Earthing Terminal
Class II Construction
Minutes
Seconds
Diameter
Grounding Terminal
Denotes Double Insulation
Time
Time
Size of Drill Bits,
min
s
ASSEMBLY
Grinding Wheels, etc.
No-load Rotational Speed
Revolutions, Surface Speed,
Strokes, etc. per Minute
Speed, Torque or Position Settings
Disconnect the power plug from the AC power source
before any assembly, adjustments, or adding/removing accessories.
Following this preventative step reduces the risk of the drill coming on acciden-
tally and the risk of damage to the workpiece and injury to the operator.
No load speed
.../min
Revolutions per Minute
1,2,3, …
Ring Selector Settings
7
8
DRILL BIT INSERTION / REMOVAL
• Unplug the drill. Never
change bits on a live drill.
• Make sure the bit is
undamaged, sharp and
free from wood or metal
shavings. Foreign
material on the bit may keep the chuck from tightening
fully. A loose bit may cause injury.
• Push the bit into the chuck as far as it will go.
OPERATING THE ON/OFF SWITCH
Squeeze the trigger switch to turn
• Make sure the bit is in the center of the chuck.
the tool “ON”. Release the trigger
switch to turn the tool “OFF”.
If the bit is off-center, it will not be held securely
and may fly loose during use causing serious
injury.
When drilling for extended
periods, the “Lock-On” switch
may be used, but do not use this
switch in situations where the drill
is likely to bind or kickback. If
kickback does occur, the sudden
motion of the tool may make it
difficult to release the “Lock-On”
switch and turn the drill off.
• Insert the chuck key into one of the three chuck
holes. Rotate the chuck key clockwise to lock the
bit in place.
• Remove the chuck key.
• Store the Chuck Key after each use in its holder
located at the power cord stem.
SPEED CONTROL ADJUSTING SWITCH
Always run the drill for one minute before drilling to make
sure the bit is properly seated. If the bit needs to be adjusted, unplug the drill
before touching the bit.
To increase the operating speed of
the drill, turn the variable speed
control clockwise. To decrease the
speed, turn the variable speed
control counterclockwise.
OPERATING THE DRILL
In certain situations, the bit may bind and the drill will kick-
back in the opposite direction. This sudden reaction could lead to loss of con-
trol and possible serious injury. Always be prepared for the possibility of kick-
back, especially when breaking through material to complete a hole.
9
10
REVERSING SWITCH LEVER
The reversing switch lever revers-
es the rotation of the drill bit. It is
located just above the trigger
switch. ALWAYS turn the motor off
and let the bit come to a
complete stop before moving the
switch.
USING THE DEPTH GAUGE
When drilling to a preset depth, use the adjustable depth gauge to mark the exact
depth needed.
• Insert depth gauge into
the hole in the side of
the handle.
F
R
• Determine drilling depth needed.
• Loosen the handle and lower the gauge until
the distance between the end of the depth
gauge and the end of the drilling bit equals the
required depth. Tighten the handle.
Move the switch to the right for a
forward rotation of the bit. Move
the switch to the left to put the bit
into reverse.
• Drill until the material touches the end of the
depth gauge. The hole will be the desired depth.
Do not change the direction of a moving bit. Make sure the
bit comes to a complete standstill before moving switch. Changing direction
while the bit is moving can cause damage to the drill.
DRILLING WOOD
• Always clamp the work piece to a steady base. Never hold in your hand or
across your legs.
HAMMER /DRILL SELECTOR
• To use the tool as a hammer,
move the hammer/drill selector
switch to the left.
• Apply pressure in line with the bit. Applying pressure at an angle could cause
the bit to bind or break.
• Thin materials that may splinter should be drilled with another piece of wood
placed underneath.
• To use the tool as a drill, move the
hammer/drill selector switch to
the right.
• Twist bits can be used for wood drilling but will overheat if the flutes are not
cleared of wood chips periodically.
• To prevent splintering when finishing holes, stop drilling just before the hole
breaks through and complete the hole from the other side.
DRILLING MASONRY
• Always use carbide tip bits for drilling masonry.
• Use an even pressure, hard enough to keep the drill biting, but not so hard that
the bit spins in the hole. Spinning the bit will dull it quickly. Bricks and similar
soft materials will take less pressure than a hard material like concrete.
11
12
DRILLING METAL
SPECIFICATIONS
• Use an even pressure, hard enough to keep the drill biting, but not so hard that
the bit spins in the hole. Spinning the bit will dull it quickly. Soft metals like
copper, cast iron, brass or aluminum will take less pressure than harder
materials like steel.
SPECIFICATIONS
Voltage
Rated Current
No-Load Speed
Impact
120V
6.6 A
0-3000/min
48000/min
60 Hz
• When drilling harder metals, use lubricating oil on the tip of the bit.
Chuck Capacity (max.)
13mm (1/2")
MAINTENANCE AND CLEANING
OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS
Unplug the drill before performing maintenance or cleaning.
Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would
like further information on the following products, please contact Alltrade Customer
Service Department at 1-800-590-3723.
• Never immerse tool in liquid. Never let any liquid inside tool housing.
• Clean with a damp cloth and mild soap. Do not use solvents or harsh detergents.
Cordless Drills/Screwdrivers
Impact Wrenches
Sanders
• Check brushes periodically. Worn brushes should be replaced by qualified serv-
ice personnel.
• Keep air vents clean and free from debris. Blocked air vents can lead to over-
heating.
Jigsaws
ACCESSORIES
Circular Saws
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become hazardous when used on
another tool.
Angle Grinders
Reciprocating Saws
Routers
Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets.
Rotary Tools
If you must use an extension cord, be sure that the gauge is large enough to carry
the amount of current necessary for your power tool.
ence a loss of power, excessive voltage drop or overheating. The smaller the gauge
number, the heavier the cord (see table below).
If not, your tool may experi-
Corded and Cordless Multi-Purpose Tools
Wide Range of Accessories and more
RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS
TOOL CURRENT RATING
CONDUCTOR SIZE IN A.W.G
AMPERE
3-6
6-8
8-10
10-12
12-16
16-20
10FT.
18
18
18
16
25FT.
18
18
18
16
50FT.
18
18
18
14
100FT.
18
16
14
14
-
14
12
12
12
12
12
-
13
14
to determine whether any item or part is nonconforming and, if so, whether the
item and/or part will be repaired and/or replaced. If the unit is repaired, new or
reconditioned replacement parts may be used. If Alltrade chooses to replace
the product, it may replace it with a new or reconditioned one of the same or
comparable design. The repaired or replaced unit will be warranted under the terms
of the remainder of the warranty period. Typically, a defective product that is
returned within the first 30 days after the purchase date will be replaced; for items
returned after the first 30 days and within the warranty period, covered defective
parts not subject to normal wear and tear or other exclusions will be repaired or
replaced, at Alltrade’s option. During the warranty period, Alltrade will be responsi-
ble for the return shipping charges. Alltrade’s repair and/or replacement of any non-
conforming item and/or part thereof shall constitute fulfillment of all
obligations to the purchaser. Alltrade shall not be responsible or liable for any
expense, including freight charges, or repairs made outside Alltrade’s facility, unless
expressly agreed to by Alltrade in writing. Under no circumstances shall Alltrade
bear any responsibility for loss of the unit, loss of time or rental, inconvenience,
commercial loss or consequential damages.
3 YEAR LIMITED WARRANTY
Express and Exclusive Limited Warranty to Original Retail Buyer
Alltrade Tools LLC (hereinafter "Alltrade") expressly warrants to the original retail
purchaser of the accompanying KAWASAKI™ power tool and no one else all parts
of the product (except those parts referred to below which are specifically exclud-
ed from such warranty (see Exclusions)) to be free from defects in materials and
workmanship for a period of three years from original date of purchase, except that
such warranty with regard to the battery shall be for a period of two years from
original date of purchase, unless the tool is used for commercial or rental
purposes.
SPECIAL WARRANTY NOTE FOR COMMERCIAL OR RENTAL USE:
The above
warranty for this Kawasaki™ power tool, including the battery, shall be effective for
only 90 days from the original date of purchase if this tool is used for any
COMMERCIAL OR RENTAL PURPOSE.
The date of purchase shall be the date of shipment to the original purchaser, or the
date the original purchaser took possession, custody or control of the product,
whichever occurred first. This warranty shall be null and void if the product or any
component thereof is modified or altered. This warranty does not apply to any
other product and/or component thereof manufactured or distributed by Alltrade,
and does not apply to products and/or components thereof designed, manufactured
and/or assembled by others, for which Alltrade makes no warranties whatsoever.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON
THE FACE HEREOF.
Exclusions
This warranty does not cover parts damaged due to normal wear, abnormal
conditions, misapplication, misuse, abuse, accidents, operation at other than
recommended pressures or temperatures, improper storage or freight damage.
Parts damaged or worn by operation in dusty environments are not warranted.
Failure to follow recommended operating and maintenance procedures also
voids warranty.
This limited warranty does not apply to accessory items such as drill bits,
screwdriving bits, circular saw blades, jigsaw blades, grinding wheels, sanding
sheets and other related items.
Warranty Performance
By purchasing the product, purchaser expressly acknowledges and agrees that their
sole and exclusive remedy under this warranty shall be strictly limited to the repair
or replacement of any covered nonconforming items or parts thereof provided that
any such nonconforming item and/or part is promptly returned to Alltrade’s facility
postage pre-paid and insured (address: ALLTRADE Warranty Claims & Repair,
1431 Via Plata, Long Beach, CA 90810, Attn: Customer Service #1-800-590-3723)
within the applicable warranty period, with a written request by purchaser that
Alltrade repair and/or replace the nonconforming item and/or part. We recommend
that you keep the original product packaging in the event you need to ship the unit.
We suggest the package be insured against loss or in transit damage. When
sending your product include your name, address, phone number, dated proof
of purchase (or copy), and a statement about the nature of problem. Warranty
coverage is conditioned upon purchaser furnishing Alltrade with adequate written
proof that they are the original purchaser and of the original purchase date. Parts
returned, freight prepaid and insured, to Alltrade’s facility (see above address) will
be inspected and, at Alltrade’s option, repaired and/or replaced free of charge if
found to be defective and subject to warranty. Alltrade retains the sole discretion
DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE,
NEGLIGENCE, FAILURE TO FOLLOW INSTRUCTIONS, UNAUTHORIZED REPAIRS
OR ALTERATIONS, DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY,
USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES,
COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO
PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS
WARRANTY.
Alltrade will not be liable for the following: labor charges, loss or damage resulting
from improper operation, maintenance or repairs made by other persons;
pre-delivery services such as assembly, oil or lubricants, and adjustment;
maintenance services that are normally required to maintain the product.
The use of other than genuine Alltrade Repair Parts will void warranty.
15
16
Warranty Disclaimers
REPRESENTATIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH
DAMAGES. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT,
WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL
ALLTRADE’S AND/OR ITS REPRESENTATIVE(S)’ LIABILITY EXCEED THE PRICE OF
THE PRODUCT. ANY AND ALL LIABILITY CONNECTED WITH THE USE OF
THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY
PERIODS SPECIFIED ABOVE.
EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES,
GUARANTIES AND/OR REPRESENTATIONS. EXCEPT FOR THE LIMITED WARRANTY
PROVIDED ABOVE, ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR
REPRESENTATIONS BY ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING
THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE
PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF
WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION,
WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY
ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE
BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE
AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY
WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR
CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON. PURCHASER’S
SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.
Limitations on Warranty Disclaimers
Some states do not allow limitations on how long an implied warranty lasts
and some states do not allow the exclusion or limitation of the incidental or
consequential damages, so part or all of the above limitations or exclusions may not
apply to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
If your product is not covered by this warranty, please call our Customer Service
Department toll free at 1-800-590-3723 for general repair information and charges.
EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE ABOVE
WARRANTY IS MADE WITH REGARD TO THIS PRODUCT. ALL EXPRESS AND/OR
IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY ALLTRADE
AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE,
PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COMPONENT
THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY,
GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY
OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF
ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE PURCHASER, INCLUDING
BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY
EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR ITS REPRESENTATIVES.
PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH
WARRANTIES AND RIGHTS, CLAIMS AND/OR CAUSES OF ACTION ARISING
THEREFROM OR BASED THEREON. PURCHASER’S SOLE AND EXCLUSIVE
REMEDY IS AS STATED ABOVE.
Limitation Of Liability
IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR
INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL DAMAGES OF ANY
KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH
OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND/OR ITS
REPRESENTATIVE(S) AND PURCHASER, ANY WARRANTY HEREUNDER,
AND/OR THE EXISTENCE, DESIGN, MANUFACTURE, PURCHASE, USE AND/OR
OPERATION OF ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS
17
18
|