Kenmore Lawn Mower 48624275 User Manual

Owner's Manual  
®
TRACTOR SNOW CAB  
Model No. 486.24275  
CAUTION:  
Safety  
Before using this product, read  
this manual and follow all  
Safety Rules and  
Assembly  
Operation  
Maintenance  
Parts  
Operating Instructions.  
IMPORTANT - READ THIS FIRST!!!  
For Missing Parts or Assembly Questions  
Please Call 866-576-8388  
Mon.-Fri. 7 am - 5 pm CST.  
FAX 217-728-2032 or e-mail [email protected]  
Missing parts will be sent UPS in 24 hours directly to your home.  
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.  
FORM NO. 48739 (REV. 7/04)  
PRINTED IN U.S.A.  
 
HARDWARE PACKAGE CONTENTS  
SHOWN FULL SIZE  
NOT SHOWN FULL SIZE  
E
A
G
B
D
F
C
REF. QTY.  
DESCRIPTION  
REF. QTY.  
DESCRIPTION  
D
E
F
2
2
4
2
Flat Washer, 5/16"  
Plug  
Rubber Pad  
Plastic Knob  
A
B
C
2
4
4
Carriage Bolt, 5/16 x 2"  
Hex Bolt, 1/4 x 1-1/2"  
Hex Lock Nut, 1/4"  
G
CARTON CONTENTS  
4. U-Tube  
1. Base Assembly  
2. Top Tubes (2)  
3. Upright Tubes (2)  
5. Support Rods (3)  
6. Front Brace Rod  
7. Vinyl Canopy  
5
4
3
6
7
2
1
3
 
ASSEMBLY  
Spread apart the slotted ends of the base assembly's  
TOOLS REQUIRED FOR ASSEMBLY  
front brackets just enough to fit them on the outside  
of the seat hinge bracket. Slide the slots over the bolt  
heads. See figure 3.  
IMPORTANT: The ends of the front brackets must fit  
snugly against the outside of the seat hinge bracket  
to keep the base assembly secured.  
Align the assembly's bottom brackets over the holes  
where you removed the seat springs. Check to see if  
the base assembly's tubing rubs against the fender. If  
the tubing rubs, apply the adhesive pads to the  
fender, under the tubing. See figure 3.  
(2)  
(1)  
7/16" Wrenches  
1/2" or 9/16" Socket Wrench  
REMOVAL OF PARTS FROM CARTON  
Remove all parts and hardware packages from the  
carton. Lay out all parts and hardware and identify.  
ASSEMBLING SNOW CAB  
SEAT HINGE BRACKET  
Your tractor fender style may differ from the one shown  
in the drawings. These instructions apply to all fender  
styles.  
FRONT BRACKET  
(BASE ASSEMBLY)  
Raise the tractor seat, unscrew the seat spring bolts  
and remove the springs from the rear fender. See  
figure 1.  
BOLT  
ADHESIVE PAD  
WASHER  
SPRING  
FIGURE 3  
Reassemble the seat springs on top of the base  
assembly's bottom brackets using the bolts and  
washers that you removed. Tighten securely, but do  
not to overtighten. See figure 4.  
FIGURE 1  
BOLT  
Push the plastic plugs into the ends of the base  
assembly tubes. See figure 2.  
WASHER  
SPRING  
PLASTIC PLUG  
FIGURE 2  
FIGURE 4  
4
 
Assemble the upright tubes to the base assembly  
using two 5/16-18 x 2" carriage bolts (on outside) and  
two 5/16" flat washers and plastic knobs (on inside).  
See figure 5.  
ALTERNATE  
MOUNTING  
HOLES  
5/16" x 2"  
PLASTIC  
KNOB  
CARRIAGE BOLT  
FRONT BRACE ROD  
5/16" FLAT  
WASHER  
FIGURE 5  
FIGURE 7  
Assemble the top tubes to the upright tubes using two  
1/4" x 1-1/2" hex bolts (from outside) and two 1/4" hex  
lock nuts (inside). Do not tighten yet. See figure 6.  
Fit the front U-tube onto the top tubes. Fasten the  
tubes together using two 1/4" x 1-1/2" hex bolts (on  
outside) and two 1/4" hex lock nuts (on inside).  
Tighten all loose bolts. See figure 6.  
Fit the three support rods into the holes in the top  
tubes, with the rods arching upward. Do not over  
bend the rods when installing. See figure 6.  
Raise the tractor's hood. Place the snow cab canopy  
onto the tubing frame, draping the front flap down in  
front of the tractor's dash panel. Lower the hood,  
trapping the front flap under the hood. Secure the  
sides of the canopy by fastening the elastic hooks to  
the bottom edge of the footrest and fender. Any  
levers or handles on snowthrowers or snow blades  
should be located outside of the cab. See figure 8.  
1/4" x 1-1/2"  
HEX BOLT  
SUPPORT ROD  
1/4" HEX  
LOCK NUT  
1/4" HEX  
LOCK NUT  
1/4" x 1-1/2"  
HEX BOLT  
FRONT FLAP  
FIGURE 6  
Insert the ends of the front brace rod into the holes in  
the U-tube and then swing the bottom of the rod  
down to rest on top of the dash panel. On newer "GT"  
tractors, use the holes at each end of the U-tube. On  
older "GT" tractors and on "LT" tractors, the alternate  
holes in the front section of the U-tube may provide  
the best fit. See figure 7.  
ELASTIC HOOK  
FIGURE 8  
5
 
OPERATION  
Read this owner's manual and safety rules before operating your tractor with the Snow Cab.  
Check the area of operation thoroughly before  
using the tractor with the snow cab. The added  
height of the snow cab and a reduced field of  
vision require extra caution during operation.  
CAUTION: Watch out for low tree  
limbs and other overhead objects which  
may interfere with the snow cab.  
Unfasten the elastic hooks on one side of the snow  
cab to get on or off the tractor.  
CAUTION: This cab provides foul  
weather protection only. It does not  
provide protection against exhaust  
fumes, collision, rollover or other acci-  
dents.  
Operate outside controls on a snowthrower or  
snow blade through the access flaps in the sides of  
the canopy.  
CAUTION: Never transport the tractor in  
an open truck or open trailer while the  
snow cab is attached.  
Remove the upper snow cab frame and canopy  
before you transport the tractor in an open truck or  
open trailer.  
MAINTENANCE/STORAGE  
CUSTOMER RESPONSIBILITIES  
Read and follow the maintenance schedule and the maintenance procedures listed in this section.  
MAINTENANCE SCHEDULE  
Fill in dates as you  
complete regular service.  
Service Dates  
Check for loose fasteners  
Cleaning  
X
X
X
CHECK FOR LOOSE FASTENERS  
STORAGE  
Before each use make a thorough visual check of  
the snow cab for any bolts and nuts which may  
have loosened. Retighten any loose bolts and nuts.  
Clean the vinyl canopy thoroughly with mild liquid  
soap and water. Allow to dry before storing. Refer  
to the Cleaning section.  
Store the snow cab in a clean, dry area away from  
direct sun light.  
CLEANING  
The vinyl portion of the canopy can be washed  
using water only, or a mild liquid soap and water.  
The plastic windows should only be washed using  
running water, or a mild liquid soap and water.  
Wash the windows with your bare hands only. A  
cloth, sponge or brush will scratch the clear plastic.  
IMPORTANT: Never clean the windows when the  
plastic is dry. The clear plastic will scratch.  
6
 
PARTS  
REPAIR PARTS FOR MODEL 486.24275 TRACTOR SNOW CAB  
5
3
3
4
12  
11  
14  
6
2
2
1
9
10  
8
7
13  
REF. PART  
QTY.  
DESCRIPTION  
Base Assembly  
Upright Tube  
Top Tube  
REF.  
NO.  
PART QTY.  
NO.  
DESCRIPTION  
NO.  
NO.  
1
2
3
4
5
6
7
8
64567  
25014  
25013  
25012  
25015  
48738  
47674  
43720  
1
2
2
1
3
1
2
2
9
44977  
43081  
43648  
43013  
48661  
48773  
25040  
48739  
2
2
4
4
4
1
4
1
Carriage Bolt, 5/16-18 x 2"  
Flat Washer, 5/16"  
Hex Bolt, 1/4-20 x 1-1/2"  
Hex Lock Nut, 1/4-20  
Adhesive Pad  
Front Brace Rod  
Elastic Hook  
10  
11  
12  
13  
14  
15  
U-Tube  
Support Rod  
Vinyl Canopy  
Plastic Plug  
Plastic Knob  
Owner's Manual  
7
 
Get it fixed, at your home or ours!  
For repair of major brand appliances in your own home…  
no matter who made it, no matter who sold it!  
1-800-4-MY-HOMESM Anytime, day or night  
(1-800-469-4663)  
To bring in products such as vacuums, lawn equipment and electronics  
Sears Parts & Repair Center.  
for repair, call for the location of your nearest  
1-800-488-1222 Anytime, day or night  
For the replacement parts, accessories and owner’s manuals  
that you need to do-it-yourself, call Sears PartsDirectSM  
!
1-800-366-PART 6 a.m. – 11 p.m. CST,  
(1-800-366-7278)  
7 days a week  
To purchase or inquire about a Sears Service Agreement:  
1-800-827-6655  
7 a.m. – 5 p.m. CST, Mon. – Sat.  
Para pedir servicio de reparación a domicilio,  
y para ordenar piezas con entrega a domicilio:  
Au Canada pour service en français:  
SM  
1-877-LE-FOYER  
SM  
1-888-SU-HOGAR  
(1-877-533-6937)  
(1-888-784-6427)  
SM  
HomeCentral  
® Registered Trademark / ™ Trademark of Sears, Roebuck and Co.  
® Marca Registrada / ™ Marca de Fábrica de Sears, Roebuck and Co.  
© Sears, Roebuck and Co.  
8
 

Ingersoll Rand Water Pump 6662AX X C User Manual
Invacare Oxygen Equipment IRC5PAW User Manual
IOGear TV Cables GCS62 User Manual
JVC Camcorder 0810YMH AL OT User Manual
JVC Car Stereo System FX240 User Manual
KEF Audio Speaker PSW 2500 User Manual
Kenwood CD Player KDC 5020 User Manual
Kenwood TV Mount 411 User Manual
KitchenAid Cooktop KECC508RPB01 User Manual
KoldFront Ice Maker KIM450S User Manual