Kenwood Carpet Cleaner SC300 User Manual

Instruction manual  
Model SC300  
Model SC400  
 
Model SC300  
DESCRIPTION OF THE APPLIANCE  
A
B
C
D
E
F
G
H
I
Floorcloth  
Main part of the appliance  
On/Off switch  
Safety Filling Cap  
On/Off pilot light  
Power cable  
Telescopic tube  
165ml measuring cup  
Funnel  
L
Preheating/cool down stand  
L
 
INSTRUCTIONS FOR USE MODEL SC300  
Using KENWOOD STEAM MOP is really very simple:  
1. After having taken the appliance out of its box, screw the telescopic tube onto the main part of the appliance (Fig.1). Then  
turn the two ends and pull them out to the desired length. Lock the upper part by turning clockwise (Figs 1a-1b).  
2. Secure the cable onto the hook at the top of the tube (Fig.2).  
3. Rest the base of KENWOOD STEAM MOP on the floorcloth, secure the floor cloth to the KENWOOD STEAM MOP using  
the Velcro straps, making sure the cloth is secured on the base (Fig.3).  
4. Unscrew the Safety cap (D) and pour 2 measuring cups (H) (330 ml) into the tank using the provided funnel, then screw  
the Safety cap back on (Fig 4).  
5. Place the Steam mop on the provided preheat tray. Plug the power cord into the power supply. Press switch (C) and wait  
for about 3 minutes (Fig.5). Do not leave the device unattended during the waiting period.  
6. As soon as steam appears from your KENWOOD STEAM MOP you can start to use it. Slowly run the KENWOOD STEAM  
MOP over the surfaces to be cleaned. DO NOT LEAVE in one spot for more than 15 seconds as it may cause a whitish  
halo to form on the surface. This is no call for concern as it may be removed using a normal decalcifying product or with  
a few drops of vinegar directly onto the floor.  
7. When KENWOOD STEAM MOP SC300 no longer emits steam it means that there is no more water (this will take place  
approximately every 15 minutes when in use).Turn off the appliance, take out the plug, and supply more water as  
described in Point 4 above.  
8. Turn your KENWOOD STEAM MOP on again and steam will start to be produced as before.  
9. When finished wash the cloth with water and soap or in washing machine. Every time you replace the cloth, turn off the  
switch (C) and do not touch the appliances hot parts.  
10. After using and before putting the appliance away, wind the power cord around the provided hooks (see Fig. 6) and empty  
any water left in the tank of the Steam Mop. Before using the appliance again, unwind the power cord completely. Be sure  
the power cord is completely unwound before you plug it in.  
CLEANING AND MAINTENANCE  
The following operation must be carried out only if the appliance is unplugged from its power source.  
In order to guarantee perfect functioning over a long period of time the tank needs to be rinsed out at least once a week with  
cold water to eliminate any accumulated calcium deposits.  
DO NOT USE VINEGAR OR OTHER DECALCIFYING SUBSTANCES.  
KENWOOD STEAM MOP does not need to be used with its own specially developed floor cloths but can be used with the  
floor cloths that you normally use in your home.  
Spare floor cloths are available by mail order from Hagemeyer.  
Attention.  
Before washing the Magic Cloth, Kenwood recommends the Magic Cloth straps be neatly joined together  
to avoid lint clogging the magic tape hooks.  
PROBLEM  
CAUSE  
SOLUTION  
Appliance  
won’t start  
* Electric plug  
*Push plug securely into outlet  
*Try another outlet  
*Check circuit breaker  
* Power switch not turned on  
* No water in tank  
*Make sure power switch is on  
*Check the tank for water  
Appliance won’t make steam  
*No water in tank  
*Check the tank for water  
Appliance leaves water on the floor  
*Floorcloth is too wet  
*Change floorcloth  
*If wood floor, dry the floor before proceeding.  
*Too much water in tank, Do not overfill  
*Turn off, unplug from electrical outlet, change  
floorcloth and reheat appliance.  
*Appliance did not remain flat on surface  
while turned on  
Appliance leaves a whitish halo on  
floor  
*Left in one spot too long  
*Remove with few drops of vinegar.  
*If above step doesn’t remove halo, then reheat  
area for one minute and discoloration will be  
removed. Do not overheat area.  
 
Model SC400  
DESCRIPTION OF THE APPLIANCE  
A
B
C
D
E
F
G
H
I
Floorcloth  
Main part of the appliance  
On/Off switch  
Safety Filling Cap  
On/Off pilot light  
Water exhaustion light  
Power cable  
Telescopic tube  
165ml measuring cup  
Funnel  
H
I
L
F
E
D
C
L
M
B
G
Preheating/cool down stand  
A
M
Fig. 3  
Fig. 1  
Fig. 2  
Fig. 4  
Fig. 5  
Fig. 6  
Fig. 7  
 
INSTRUCTIONS FOR USE MODEL SC400  
Using KENWOOD STEAM MOP is really very simple:  
1. Once the appliance has been unpacked, fit the extension tube in the appliance’s body and then extend it to the desired  
length (fig. 1).  
2. Fix the top part of the tube by turning it in a clockwise direction (fig. 2).  
3. Fix the cord into the hook which is provided along the tube (fig. 3)  
4. Rest the base of KENWOOD STEAM MOP on the floorcloth, secure the floor cloth to the KENWOOD STEAM MOP using  
the Velcro straps, making sure the cloth is secured on the base (fig. 4).  
5. Unscrew the cap (D) and pour 2 measuring jugs (I) of water into the tank using the provided funnel (L) (fig. 5). Then screw  
the safety cap on tightly. Now insert the plug into the power outlet.  
6. Place the Steam Mop on the provided preheat tray. Press the switch (C), the pilot light (E) will go on (fig. 6). Do not leave  
the appliance unattended while you are waiting for the Steam Mop to heat up.  
7. When steam starts coming out, slowly run the appliance over the surfaces to be cleaned. This way your floors will  
become perfectly clean.DO NOT LEAVE in one spot for more than 15 seconds as it may cause a whitish halo to form on  
the surface. This is no call for concern as it may be removed using a normal decalcifying product or with a few drops of  
vinegar directly onto the floor.  
8. When Steam Mop stops producing steam and the water exhaustion light (F) goes on it means that the water has run  
out (approximately every 15 minutes use). In this case, press the switch (C), unplug the appliance and refill with water as  
described at point 5. During this operation, mind not to touch the appliances hot parts.  
9. Press the switch (C) again. Steam Mop will restart producing steam.  
10. When finished wash the cloth with water and soap or in washing machine.Every time you replace the cloth, turn off the  
switch (C) and do not touch the appliances hot parts.  
11. After using and before putting the appliance away, wind the power cord around the provided hooks (see fig. 7) and empty  
any water left in the tank of the Steam Mop. Before using the appliance again, unwind the power cord completely. Be sure  
the power cord is completely unwound before you plug it in.  
CLEANING AND MAINTENANCE  
The following operation must be carried out only if the appliance is unplugged from its power source.  
In order to guarantee perfect functioning over a long period of time the tank needs to be rinsed out at least once a week with  
cold water to eliminate any accumulated calcium deposits.  
DO NOT USE VINEGAR OR OTHER DECALCIFYING SUBSTANCES.  
KENWOOD STEAM MOP does not need to be used with its own specially developed floor cloths but can be used with the  
floor cloths that you normally use in your home.  
Spare floor cloths are available by mail order from Hagemeyer.  
Attention.  
Before washing the Magic Cloth, Kenwood recommends the Magic Cloth straps be neatly joined together  
to avoid lint clogging the magic tape hooks.  
PROBLEM  
CAUSE  
SOLUTION  
Appliance  
won’t start  
* Electric plug  
*Push plug securely into outlet  
*Try another outlet  
*Check circuit breaker  
* Power switch not turned on  
* No water in tank  
*Make sure power switch is on  
*Check the tank for water  
Appliance won’t make steam  
*No water in tank  
*Check the tank for water  
Appliance leaves water on the floor  
*Floorcloth is too wet  
*Change floorcloth  
*If wood floor, dry the floor before proceeding.  
*Too much water in tank, Do not overfill  
*Turn off, unplug from electrical outlet, change  
floorcloth and reheat appliance.  
*Appliance did not remain flat on surface  
while turned on  
Appliance leaves a whitish halo on  
floor  
*Left in one spot too long  
*Remove with few drops of vinegar.  
*If above step doesn’t remove halo, then reheat  
area for one minute and discoloration will be  
removed. Do not overheat area.  
 
HAGEMEYER AUSTRALASIA B.V.  
104 Vanessa street  
Kingsgrove  
NSW 2208  
Ph: (02) 93.70.88.77  
LIMITED  
New Lane. Havant. Hants. P09 2NH  
 

IRiver MP3 Player iFP 300 Series User Manual
Jasco Universal Remote RM24948 User Manual
Jensen Car Video System VM9312HD User Manual
JVC Camcorder LYT2044 001C M User Manual
JVC CRT Television AV 27320 User Manual
JVC Portable CD Player 0404SKMCREORI User Manual
Kenmore Slow Cooker 68332 User Manual
KitchenAid Blender KSB1570 User Manual
KitchenAid Microwave Oven 3828W5A0969 User Manual
Kramer Electronics Speaker SPK C613 User Manual