Kenwood Two Way Radio TK 2360 User Manual

INSTRUCTION MANUAL  
VHF FM TRANSCEIVER  
TK-2360  
UHF FM TRANSCEIVER  
TK-3360  
© B62-2182-00 (K, K2)  
09 08 07 06 05 04 03 02 01 00  
 
One or more of the following statements may be applicable:  
FCC WARNING  
Th s equ pment generates or uses rad o frequency energy.  
Changes or modifications to this equipment may cause harmful  
interference unless the modifications are expressly approved in the  
instruction manual. The user could lose the authority to operate this  
equipment if an unauthorized change or modification is made.  
INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY  
THE FCC  
This equipment has been tested and found to comply with the limits  
for a Class B digital device, pursuant to Part 15 of the FCC Rules.  
These limits are designed to provide reasonable protection against  
harmful interference in a residential installation.  
This equipment generates, uses and can generate radio  
frequency energy and, if not installed and used in accordance  
with the instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that the  
interference will not occur in a particular installation. If this equipment  
does cause harmful interference to radio or television reception,  
which can be determined by turning the equipment off and on, the  
user s encouraged to try to correct the nterference by one or more of  
the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment to an outlet on a circuit different from  
that to which the receiver is connected.  
Consult the dealer for technical assistance.  
The RBRC Recycle seal found on Kenwood  
lithium-ion (Li-ion) battery packs indicates  
Kenwood’s voluntary participation in an industry  
program to collect and recycle Li-ion batteries  
after their operating life has expired. The RBRC  
program is an alternative to disposing Li-ion  
batteries with your regular refuse or in municipal  
waste streams, which is illegal in some areas.  
For information on Li-ion battery recycling in your area, call (toll  
free) 1-800-8-BATTERY (1-800-822-8837).  
Kenwood’s involvement in this program is part of our commitment  
to preserve our environment and conserve our natural resources.  
 
The RBRC Recycle seal found on Kenwood nickel  
metal hydride (Ni-MH) battery packs indicates  
Kenwood’s voluntary participation in an industry  
program to collect and recycle Ni-MH batteries after  
their operating life has expired. The RBRC program  
is an alternative to disposing Ni-MH batteries with  
your regular refuse or in municipal waste streams,  
which is illegal in some areas.  
For information on Ni-MH battery recycling in your area, call (toll  
free) 1-800-8-BATTERY (1-800-822-8837).  
Kenwood’s involvement in this program is part of our commitment  
to preserve our environment and conserve our natural resources.  
Precautions  
Do not charge the transceiver and battery pack when they are wet.  
Ensure that there are no metallic items located between the  
transceiver and the battery pack.  
Do not use options not specified by Kenwood.  
If the die-cast chassis or other transceiver part is damaged, do not  
touch the damaged parts.  
If a headset or headphone is connected to the transceiver, reduce  
the transceiver volume. Pay attention to the volume level when  
turning the squelch off.  
Do not place the microphone cable around your neck while near  
machinery that may catch the cable.  
Do not place the transceiver on unstable surfaces.  
Ensure that the end of the antenna does not touch your eyes.  
When the transceiver is used for transmission for many hours, the  
radiator and chassis will become hot. Do not touch these locations  
when replacing the battery pack.  
Always switch the transceiver power off before installing optional  
accessor es.  
The charger is the device that disconnects the unit from the AC  
mains line. The AC plug should be readily accessible.  
 
Turn the transceiver power off in the following locations:  
Near blasting sites.  
In airplanes. (Any use of the transceiver must follow the  
instructions and regulations provided by the airline crew.)  
Where restrictions or warnings are posted regarding the use of  
radio devices, including but not limited to medical facilities.  
Near persons using pacemakers.  
Do not disassemble or modify the transceiver for any reason.  
Do not place the transceiver on or near airbag equipment while  
the vehicle is running. When the airbag inflates, the transceiver  
may be ejected and strike the driver or passengers.  
Do not transmit while touching the antenna terminal or if  
any metallic parts are exposed from the antenna covering.  
Transmitting at such a time may result in a high-frequency burn.  
If an abnormal odor or smoke is detected coming from the  
transceiver, switch the transceiver power off immediately,  
remove the battery pack from the transceiver, and contact your  
Kenwood dealer.  
Use of the transceiver while you are driving may be against  
traffic laws. Please check and observe the vehicle regulations  
n your area.  
Do not expose the transceiver to extremely hot or cold  
cond t ons.  
Do not carry the battery pack (or battery case) with metal  
objects, as they may short the battery terminals.  
Danger of explosion if the battery is incorrectly replaced;  
replace only with the same type.  
 
information concerning the battery Pack  
The battery pack includes flammable objects such as organic solvent.  
Mishandling may cause the battery to rupture producing flames or  
extreme heat, deteriorate, or cause other forms of damage to the  
battery. Please observe the following prohibitive matters.  
Do not disassemble or reconstruct battery!  
The battery pack has a safety function and protection circuit to  
avoid danger. If they suffer serious damage, the battery may  
generate heat or smoke, rupture, or burst into flame.  
Do not short-circuit the battery!  
Do not join the + and – terminals using any form of metal (such  
as a paper clip or wire). Do not carry or store the battery pack  
in containers holding metal objects (such as wires, chain-  
necklace or hairpins). If the battery pack is short-circuited,  
excessive current will flow and the battery may generate heat  
or smoke, rupture, or burst into flame. It will also cause metal  
objects to heat up.  
Do not incinerate or apply heat to the battery!  
If the insulator is melted, the gas release vent or safety function  
is damaged, or the electrolyte is ignited, the battery may  
generate heat or smoke, rupture, or burst into flame.  
Do not use or leave the battery near fires, stoves, or other  
heat generators (areas reaching over 80°C/ 176°F)!  
If the polymer separator is melted due to high temperature,  
an internal short-circuit may occur in the individual cells and  
the battery may generate heat or smoke, rupture, or burst into  
flame.  
Avoid immersing the battery in water or getting it wet by  
other means!  
If the battery becomes wet, wipe it off with a dry towel before  
use. If the battery’s protection circuit is damaged, the battery  
may charge at extreme current (or voltage) and an abnormal  
chemical reaction may occur. The battery may generate heat or  
smoke, rupture, or burst into flame.  
iv  
 
Do not charge the battery near fires or under direct  
sunlight!  
If the battery’s protection circuit is damaged, the battery may  
charge at extreme current (or voltage) and an abnormal  
chemical reaction may occur. The battery may generate heat or  
smoke, rupture, or burst into flame.  
Use only the specified charger and observe charging  
requirements!  
If the battery is charged in unspecified conditions (under high  
temperature over the regulated value, excessive high voltage  
or current over regulated value, or with a remodelled charger),  
it may overcharge or an abnormal chemical reaction may occur.  
The battery may generate heat or smoke, rupture, or burst into  
flame.  
Do not pierce the battery with any object, strike it with an  
instrument, or step on it!  
This may break or deform the battery, causing a short-circuit.  
The battery may generate heat or smoke, rupture, or burst into  
flame.  
Do not jar or throw the battery!  
An impact may cause the battery to leak, generate heat  
or smoke, rupture, and/or burst into flame. If the battery’s  
protection circuit is damaged, the battery may charge at an  
abnormal current (or voltage), and an abnormal chemical  
react on may occur.  
Do not use the battery pack if it is damaged in any way!  
The battery may generate heat or smoke, rupture, or burst into  
flame.  
Do not solder directly onto the battery!  
If the insulator is melted or the gas release vent or safety  
function is damaged, the battery may generate heat or smoke,  
rupture, or burst into flame.  
Do not reverse the battery polarity (and terminals)!  
When charging a reversed battery, an abnormal chemical  
reaction may occur. In some cases, an unexpected large  
amount of current may flow upon discharging. The battery may  
generate heat or smoke, rupture, or burst into flame.  
v
 
Do not reverse-charge or reverse-connect the battery!  
The battery pack has positive and negative poles. If the battery  
pack does not smoothly connect with a charger or operating  
equipment, do not force it; check the polarity of the battery. If  
the battery pack is reverse-connected to the charger, it will be  
reverse-charged and an abnormal chemical reaction may occur.  
The battery may generate heat or smoke, rupture, or burst into  
flame.  
Do not touch a ruptured and leaking battery!  
If the electrolyte liquid from the battery gets into your eyes,  
wash your eyes out with fresh water as soon as possible,  
without rubbing your eyes. Go to the hospital immediately. If  
left untreated, it may cause eye-problems.  
Do not charge the battery for longer than the specified  
time!  
If the battery pack has not finished charging even after the  
regulated time has passed, stop it. The battery may generate  
heat or smoke, rupture, or burst into flame.  
Do not place the battery pack into a microwave or high  
pressure container!  
The battery may generate heat or smoke, rupture, or burst into  
flame.  
Keep ruptured and leaking battery packs away from fire!  
If the battery pack is leaking (or the battery emits a bad odor),  
immediately remove it from flammable areas. Electrolyte  
leaking from battery can easily catch on fire and may cause the  
battery to generate smoke or burst into flame.  
Do not use an abnormal battery!  
If the battery pack emits a bad odor, appears to have different  
coloring, is deformed, or seems abnormal for any other reason,  
remove it from the charger or operating equipment and do not  
use it. The battery may generate heat or smoke, rupture, or  
burst into flame.  
vi  
 
CONTENTS  
Unpac k ing and c hec k ing eq Uipment  
pr epar at io n  
2
7
8
o r ient at io n  
pr o g r ammabl e aUx il iar y FUnc t io ns  
bas ic o per at io ns  
sc an  
2
4
5
6
Fleets ync: al phanUmer ic 2-Way pag ing s y s t em  
Vo ic e o per at ed t r ans mis s io n (Vo x )  
bac k g r o Und o per at io ns  
UNPACKING AND CHECKING EQUIPMENT  
Note: t hese unpacking instructions are for use by your Kenwood  
dealer, an authorized Kenwood service facility, or the factory  
c arefully unpack the transceiver if any items are missing or  
damaged, file a claim with the carrier immediately.  
SUPPlIED ACCESSOrIES  
belt clip  
s peaker/ microphone jacks cap  
s peaker/ microphone locking bracket  
Stopper (4-channel: white)  
s topper (8-channel: gray)  
s topper ( 2-channel: black)  
instruction manual  
 
PrEPArATION  
INSTAllING/ rEMOvING THE (OPTIONAl) BATTEry PACK  
1
match the guides of the  
battery pack with the grooves  
on the upper rear of the  
transceiver, then firmly press  
the battery pack in place  
2
2
3
l ock the safety catch to  
prevent accidentally releasing  
the battery pack  
1
t o remove the battery pack,  
lift the safety catch, press the  
release latch, then pull the  
battery pack away from the  
transceiver  
3
Note:  
For battery pack charging procedures and useage, refer to the  
battery charger instruction manual  
before charging a battery pack that is attached to the  
transceiver, ensure that the safety catch is firmly closed.  
INSTAllING/ rEMOvING AlKAlINE BATTErIES  
Do not install batteries in a hazardous environment where  
sparks could cause an explosion  
Never discard batteries in fire; extremely high temperatures can  
cause batteries to explode  
do not short circuit the battery case terminals  
do not use rechargeable batteries  
 
2
Note:  
if you do not plan to use the transceiver for a long period,  
remove the batteries from the battery case  
t his battery case has been designed for transmitting at a  
power of approximately 1 W (the low power setting on your  
transceiver). If you want to transmit a stronger signal (using  
the high power setting on your transceiver), use an optional  
rechargeable battery pack  
1
2
t o open the battery case, press  
on the two tabs on the upper  
rear of the case, then pull the  
two halvs apart.  
insert 6 aa (l r 6) alkaline  
batteries into the battery case  
be sure to match the polarities  
with those marked in the bottom  
of the battery case  
3
Align the tabs of the cover with  
the base, then push down on  
the cover until it locks in place  
INSTAllING THE (OPTIONAl) ANTENNA  
Screw the antenna into the  
connector on the top of the  
transceiver by holding the antenna  
at its base and turning  
it clockwise until secure.  
 
INSTAllING THE BElT ClIP  
Note: When first installing the belt clip, you must remove the  
battery pack from the rear of the transceiver  
1
Remove the 2 screws from the  
rear of the transceiver, then  
remove the small, plastic black  
covering that was held in place.  
Plastic  
covering  
2
3
insert the belt clip mount into  
the space on the rear of the  
transceiver  
Using the 2 screws, affix the belt  
clip in place  
When the belt clip is not installed, leave the plastic covering in  
place  
Do not use glue which is designed to prevent screw loosening  
when installing the belt clip, as it may cause damage to the  
transceiver. Acrylic ester, which is contained in these glues, may  
crack the transceiver’s back panel  
INSTAllING THE CAP OvEr THE SPEAKEr/ MICrOPHONE JACKS  
Install the cap over the speaker/ microphone jacks when not  
using an optional speaker/ microphone  
Note: To keep the transceiver water resistant, you must cover the  
speaker/ microphone jacks with the supplied cap.  
1
place the cap over the jacks so that the  
locking tabs insert into the transceiver  
grooves  
 
4
2
While holding the cap in place, push it  
towards the bottom of the transceiver until  
the tabs on the cap click into place  
t o remove the cap, hold the top of the cap  
in place with your finger while inserting a 3  
mm or smaller flat blade screwdriver under  
the bottom of the cap. Slowly slide the  
screwdriver in until its tip touches the tab  
inside the cap, then gently pry the cap up  
(handle of screwdriver moving away from the  
transceiver) to remove the cap  
INSTAllING THE (OPTIONAl) SPEAKEr/ MICrOPHONE  
Note: The transceiver is not fully water resistant when using a  
speaker/ microphone or headset  
1 insert the speaker/ microphone plugs  
into the speaker/ microphone jacks of the  
transceiver  
2
3
place the locking bracket over the speaker/  
microphone plugs so that the locking tabs  
insert into the transceiver grooves  
While holding the locking bracket in  
place, push it towards the bottom of the  
transceiver until the tabs on the bracket  
click into place  
t o remove the locking bracket, push the  
bracket up from the base  
 
5
INSTAllING THE CHANNEl STOPPEr  
t here are types of stoppers available, depending on the  
number of channels used (4 channel type: white, 8 channel  
type: gray, and 2 channel type: black)  
1
s et the s elector knob to channel , then pull the s elector  
knob off the transciever  
if the s elector is not positioned at channel , the s elector knob  
may not install correctly and the channel may be unable to be  
changed  
2
3
insert the appropriate channel stopper  
r einsert the s elector knob  
3
1
2
 
6
OrIENTATION  
Channel Selector  
r otate to select a channel  
Power switch/ Volume control  
r otate to turn the transceiver o n/o FF and to adjust the  
volume  
Transmit/ Receive/ Battery low indicator  
If enabled by your dealer, lights red while transmitting,  
green while receiving a call, and orange when receiving an  
optional signaling call (2-tone, dt mF signaling, etc ) blinks  
red when the battery power is low while transmitting.  
Auxiliary key  
press or hold to activate its programmable function {page 8}  
PTT (Push-To-Talk) switch  
Press and hold this switch, then speak into the microphone  
to call a station  
 
7
Side 1 key  
press or hold to activate its programmable function {page 8}  
Side 2 key  
press or hold to activate its programmable function {page 8}  
Speaker/ microphone jack  
c onnect a speaker/ microphone or headset here {page 5}  
Otherwise, keep the supplied cap in place.  
PrOGrAMMABlE AUXIlIAry FUNCTIONS  
your dealer can program the Auxiliary, Side 1, and Side 2  
keys each with 1 or 2 of the following functions. Because each  
key can be programmed with up to 2 functions, there are 2  
methods of accessing the programmed functions Functions  
can be accessed by either pressing the key or by pressing and  
holding the key ask your dealer for details  
n None  
no function has been programmed  
n 2-tone  
press this key to send the 2-tone code assigned to it  
n Autodial  
press this key to call the dt mF number that has been  
programmed onto your selected channel your dealer may  
program different dt mF numbers on different channels  
n Battery Indicator  
press this key to announce the current battery energy level  
battery level 4 (green l ed) means the battery is full, level  
3 (orange LED) is sufficient, level 2 (red LED) is low, and  
level 1 (flashing red LED) is very low.  
 
8
n Emergency  
press and hold this key to enter emergency mode When  
the transceiver enters Emergency mode, it will change to  
the emergency channel and begin transmitting based on  
your dealer settings  
Note: t his function can be programmed only on the auxiliary  
key  
n Key lock  
press this key to lock and unlock the transceiver keys  
While k ey l ock is activated, you cannot use the Auxiliary,  
Side 1, Side 2, and microphone pF keys  
Note: You can still use the following key functions when Key  
l ock is activated: emergency, l one Worker, monitor, monitor  
momentary, s quelch o ff, s quelch o ff momentary, k ey l ock,  
pt t + autodial, pt t + 2-tone  
n lone Worker  
press this key to toggle the l one Worker function o n or  
o FF if the transceiver is not operated for the  
pre-programmed time, it will emit a Lone Worker tone.  
Subsequently, if no operation is performed while the tone is  
emitted, the transceiver will enter Emergency mode.  
n low Transmit Power  
Press this key to change the transmit power on the current  
channel to low power, to conserve battery energy.  
n Monitor  
press this key to deactivate q t or dq t signaling press  
this key again to return to normal operation  
 
n Monitor Momentary  
press and hold this key to deactivate q t or dq t signaling  
r elease the key to return to normal operation  
n Paging  
after selecting your desired Fleets ync channel, press this  
key to transmit your pt t l ist id, to request a call  
n Priority Channel Select  
press this key to set the currently selected channel as  
the Priority channel. During Scan, the transceiver will  
automatically change to the Priority channel when a call is  
received on that channel, even if a call is being received on  
a normal channel  
n Scan  
press this key to toggle s can o n and o FF While  
scanning, the transceiver checks for a signal on each  
channel and only stops if a signal is present  
n Scan Temporary Delete  
When scan pauses at an undesired channel, you can  
temporarily remove that channel from the scanning  
sequence by pressing this key  
n Scrambler  
press this key to toggle the s crambler function o n and  
OFF. The Scrambler allows you to hold conversations in  
complete privacy by encrypting your transmitted signals  
n Squelch Off  
press this key to hear background noise press this key  
again to return to normal operation  
 
0
n Squelch Off Momentary  
press and hold this key to hear background noise press  
this key again to return to normal operation  
n Status 1/ Status 2  
press the Status 1 or Status 2 key to transmit the status  
message assigned to them  
n Talk Around  
press this key to toggle the t alk around function o n and  
OFF. Talk Around allows you to communicate directly with  
other transceivers without the use of a repeater, as long  
they are not too far away or there are no geographical  
obstacles in the way.  
BASIC OPErATIONS  
SWITCHING POWEr ON/OFF  
t urn the Power switch/ Volume control clockwise to switch the  
transceiver o n  
t urn the Power switch/ Volume control counterclockwise fully  
to switch the transceiver OFF.  
ADJUSTING THE vOlUME  
r otate the Power switch/ Volume control to adjust the volume  
Clockwise increases the volume and counterclockwise  
decreases it  
SElECTING A CHANNEl  
s elect your desired channel using the s elector knob each  
channel is programmed with settings for transmitting and  
receiving  
 
TrANSMITTING/ rECEIvING  
1
2
s elect your desired channel  
press the key programmed as Monitor or Squelch Off to  
check whether or not the channel is free.  
If the channel is busy, wait until it becomes free.  
3
press the PTT switch and speak into the microphone.  
r elease the PTT switch to receive.  
For best sound quality, hold the transceiver approximately  
5 inches ( ~ 4 cm) from your mouth  
If signaling has been programmed on the channel, you will  
hear a call only if the received signal matches your transceiver  
settings  
SCAN  
s can monitors for signals on the transceiver channels While  
scanning, the transceiver checks for a signal on each channel  
and only stops if a signal is present  
t o begin scanning, press the key programmed as Scan  
When a signal is detected on a channel, s can pauses at that  
channel. The transceiver will remain on the busy channel until the  
signal is no longer present, at which time Scan resumes.  
t o stop scanning, press the Scan key again  
Note: t o use s can, there must be at least 2 channels in the scan  
sequence  
 
2
PrIOrITy SCAN  
if a priority channel has been programmed, the transceiver  
will automatically change to the Priority channel when a call is  
received on that channel, even if a call is being received on a  
normal channel  
if the priority channel has been set as o perator s electable by  
your dealer, you can set a new channel as the Priority channel  
by selecting your desired channel and pressing the key  
programmed as Priority Channel Select  
TEMPOrAry CHANNEl lOCKOUT  
During scan, you can temporarily remove specific channels  
from the scanning sequence by pressing the key programmed  
as Scan Temporary Delete while Scan is paused at the  
undesired channel  
The channel is no longer scanned. However, when scanning is  
ended and restarted, the channels are reset and deleted channels  
will again be in the scanning sequence.  
SCAN rEvErT  
The Scan Revert channel is the channel selected when you  
press the PTT switch to transmit during scan. Your dealer can  
program one of the following types of Scan Revert channels:  
Selected: t he last channel selected before scan  
Selected + Talkback: s ame as “s elected”, plus you can  
respond to calls on the channel at which scan is paused.  
Priority: t he priority channel  
Priority + Talkback: s ame as “priority”, plus you can  
respond to calls on the channel at which scan is paused.  
Last Called + Selected: The last channel on which you  
receive a call or the last channel selected before scan,  
whichever operation occured latest.  
 
FleetSync: AlPHANUMErIC 2-WAy PAGING FUNCTION  
FleetSync is an Alphanumeric 2-way Paging Function, and is a  
protocol owned by Kenwood c orporation  
Note: if set up by your dealer, your transceiver may use the  
mdc - 200 feature in place of Fleets ync mdc - 200 and Fleets ync  
cannot be operated simultaneously  
SElCAll (SElECTIvE CAllING)  
a s elcall is a voice call to a station or group of stations  
n Transmitting  
1
s elect your desired Fleets ync channel  
your dealer can program different id codes on different  
channels  
2 press the PTT switch and begin your conversation.  
n receiving  
If enabled by your dealer, an alert tone will sound and the  
LED will blink when a Selcall has been received.  
t o respond to the call, press the PTT switch and speak into  
the microphone  
n Identification Codes  
an id code is a combination of a -digit Fleet number and a  
4-digit ID number. Each transceiver has its own ID.  
PAGING CAll  
1
2
s elect your desired Fleets ync channel  
press the key programmed as Paging to transmit your pt t  
l ist id, to request a call  
 
4
STATUS MESSAGE  
you can transmit pre-programmed s tatus messages by  
pressing the keys programmed as Status 1 or Status 2  
s tatus messages are 2-digit codes ranging from 0 to  
(80 ~  
are reserved for special messages)  
vOICE OPErATED TrANSMISSION (vOX)  
VOX operation allows you to transmit hands-free. This feature  
can be activated or deactivated by your dealer  
vOX GAIN lEvEl  
1
2
c onnect a headset to the transceiver  
With the transceiver power off, press and hold the Side 1  
key for 2 seconds while turning the transceiver power ON.  
The LED flashes red and green.  
3
4
press the Side 1 key to increase the Vo x g ain level, and  
the Side 2 key to decrease the level  
t he Vo x g ain can be adjusted from levels to 0 and off  
While adjusting the level, speak into the headset  
microphone to test the sensitivity level (your voice is not  
trasmitted during this test procedure )  
When sound is recognized, the l ed lights orange  
5
press the PTT switch to save the setting.  
 
5
vOX OPErATION  
1
2
c onnect a headset to the transceiver  
t o transmit, simply speak into the microphone  
t he transceiver recognizes sound levels depending on the  
VOX Gain level. If it is too sensitive, it will transmit when there  
is noise in the background. If it is not sensitive enough, it will  
not pick up your voice when you begin speaking.  
3
When you finish speaking, transmission ends.  
BACKGrOUND OPErATIONS  
your dealer can activate a variety of transceiver functions to  
perform without any additional operation on your part.  
TIME-OUT TIMEr (TOT)  
t he t ime-out t imer is used to prevent you from using a  
channel for an extended duration if you continuously transmit  
for a preset time, the transceiver will stop transmitting and an  
alert tone will sound. Release the PTT switch.  
BATTEry SAvEr  
The Battery Saver decreases the amount of power used when  
a signal is not being received and no operations are being  
performed  
lOW BATTEry WArNING  
Low Battery Warning alerts you when the battery needs to be  
recharged your dealer can set an alert tone to sound and  
the LED indicator to blink red when the battery power is low.  
r echarge or replace the battery pack at this time  
 
6
PTT ID  
PTT ID is the transceiver unique ID code which is sent each  
time the PTT switch is pressed and/or released.  
COMPANDEr  
if programmed by your dealer for a channel, the compander  
will remove excessive noise from transmitted signals, to  
provide higher clarity of signals  
BUSy CHANNEl lOCKOUT (BCl)  
If BCL is set up by your dealer, you will be unable to transmit if  
the channel is already in use. Use a different channel or wait  
until the channel becomes free  
vOICE ANNOUNCEMENT  
When turning on the transceiver power and when changing the  
channel, an audio voice will announce the selected channel  
and the channel’s Vo x and scrambler settings  
QUIET TAlK (QT)/ DIGITAl QUIET TAlK (DQT)  
your dealer may have programmed q t or dq t signaling on  
your transceiver channels a q t tone/ dq t code is a  
sub-audible tone/code which allows you to ignore (not hear)  
calls from other parties who are using the same channel.  
STUN CODE  
This function is used when a transceiver is stolen or lost.  
When the transceiver receives a call containing a stun code,  
the transceiver becomes disabled t he stun code is cancelled  
when the transceiver receives a call with a revive code.  
 
7
OPTIONAl SIGNAlING  
your dealer may also program several types of optional  
signaling for your transceiver channels  
2-tone Signaling: 2-tone Signaling opens the squelch only when  
your transceiver receives a call containing matching 2 tones  
DTMF Signaling: dt mF s ignaling opens the squelch only  
when the transceiver receives a call containing a matching  
dt mF code  
FleetSync Signaling: r efer to “s el c al l (s el ec t iVe  
c al l ing )” on page 4  
MDC-1200: mdc - 200 is a data system using audio  
Frequency s hift k eying (aFs k )  
 
8

Insignia MP3 Docking Station NS S4000 User Manual
Insignia Speaker NS P2000 User Manual
Insignia Speaker NS PLTPSP User Manual
Invacare Bathroom Aids H190 User Manual
IOGear Computer Keyboard GKM512 User Manual
Kenmore Microwave Oven 72180412 User Manual
Kenmore Oven 7904717 User Manual
Kenwood Car Stereo System KAC 749S User Manual
KitchenAid Mixer KSM7586P User Manual
Kodak Film Camera 65MM User Manual