1
Remote Control Instruction Manual
Preset Remote Control Quick Start Guide
Quick start guide ................................................ 1
Getting the most from your remote control ................. 3
Remote operation of other components .................... 11
In case of difficulty ............................................ 14
Thisquickstartguideexplainshowtosetuptheremote
control to operate audio and video components other
than the receiver.
In order to make full use of the functions of the remote
control, be sure to read the section of this manual
entitled “Getting the most from your remote control”.
It contains a detailed explanation of how to operate the
remote control and make the necessary settings.
The quick start guide describes the operation of the
following keys:
SHIFT
MACRO
MOVIE
1 Display operation 1 key
Use this key to go back to the previous display or initial
display.
MUSIC
TV
AV. POWER
SYS. POWER
2 Display operation 2 key
Gets you into and out of the preset code registration
mode.
3 Display
+
+
CH.
VOL.
The information for setup is displayed.
CH.
VOL.
–
–
4 5/∞keys
MUTE
DIMMER
BASS BOOST
Use these keys to select the source or setup code.
LISTEN M.
SOUND
SUB.W.
MENU
TITLE/GUIDE
TUNING
5 MOVIE, MUSIC, and TV keys
BAND
Use these keys to select the input you want to register.
ENTER
RETURN
/PAGE
OSD
/PAGE
6 AV.POWER
key
AUTO/MONO
F.SHIFT
Once you have entered the setup code for another
component, you can press this key to turn power to that
component on or off. This lets you confirm that you
entered the code properly.
REC
LEARN
REPEAT
1
RANDOM
2
INPUT SEL.
3
TV SELECT
4
DISPLAY
5
SELECT
6
AUDIO
7
THEME
8
FAVORITE
9
INFO.
+10
EXIT
0
LAST CHANNEL
+100
10
11
12
REMOTE CONTROL UNIT
RC-R0808
RmeCntrol
B60-4611-00 (EN)
Getting the most from your remote control
The remote control supplied with this receiver is also
Registering setup codes for other components
capable of controlling components from a variety of manu-
facturers once you register the appropriate setup codes
into the remote control unit.
Refer to "Remote operation of other components" for de-
tails about the operations available for each component.
!
3
Display
Display operation 1
Display operation 2
5/∞
+
–
+
–
Low battery warning
Replace all four batteries with new ones when you notice a shortening
of the distance from which the remote control will operate. The remote
control is designed to retain setup codes in memory while you change
batteries.
Press the display operation 1 key repeatedly until
“Menu” appears in the display.
1
How to use the display operation keys
To register the setup code, use the display operation 1 key, display
operation 2 key, or 5/∞keys.
Video1:
VCR
Menu
Display
Display operation 1
Display operation 2
For step 1 through step @, make sure you start the next step
within8secondsofcompletingthepreviousone. Ifmorethan
8 seconds elapses between any two steps, press the display
operation keys so that the display appears.
5/∞
+
–
+
–
Press the display operation 2 [Menu] key repeatedly until
2
“01.IR” appears in the display.
• The setup display appears.
The display operation 1 key and display operation 2 key work as the
function key displayed in the display above.
>01.IR
>02.Surround
Home Enter
The display operation 1 key
• [Back]
Go back to the previous display.
• [Home]
Go back to the initial display.
Press the 5/∞keys to select “01.IR,” then press the
3display operation 2 [Enter] key.
• The input selecting display appears.
>05.VCR
>06.Cable
Back Enter
• [Clr]
Erase the internal memory.
>03.Video1
>04.Video2
Back Enter
The display operation 2 key
• [Enter]
Enter the selected item.
• [Menu]
Display the menu.
• [Setup]
• At this time all inputs become available regardless of any earlier
registration.
Go to the setup display.
• [Exit]
Press the 5/∞keys to select the input that you want to
4register.
Exit from the current operation.
• [Sel]
Select the item.
• Each time you press the 5/∞key, the input changes as follows:
01:
02:
03:
04:
05:
06:
07:
08:
09:
10:
CD/DVD
MD/Tape
Video1
Video2
Video3
DVD
When the display goes off
The display goes off automatically when you do not operate for more than
8 seconds. In this case, press the display operation 1 key, display
operation 2 key, or 5/∞keys.
TV1
When you are confused about what’s being displayed
Press the display operation 1 key repeatedly until “Menu” appears in the
TV2
Cable
Phono
display.
The display returns to the initial display.
• Example: To select the source connected the VIDEO1 jack, select
"Video1".
RmeCntrol
Continued to next page
Getting the most from your remote control
Press the display operation 2 [Enter] key.
• The display returns to the setup display.
5Press the display operation 2 [Enter] key.
• The source selecting display appears.
@
4
• When you select “Phono” in step 4, go to step 0.
>01.IR
>02.Surround
Home Enter
>05.VCR
>06.Cable
Back Enter
Repeat steps 3 to @ to register additional components
until all components have been registered.
Press the 5/∞keys to select the source you want to
6register.
• Each time you press the 5/∞key, the input changes as follows:
To returns to the initial display, press [Back] repeat-
01:
02:
03:
04:
05:
06:
07:
08:
09:
10:
11:
12:
13:
CD
edly until “Menu” appears in the display.
Tape
MD
CD-R
Video1:
VCR
VCR
Cable
Satellit
TV
Menu
LD
• Once registered, the display on the receiver shows the component
type instead of the default input name.
Example: if you register a VCR at the VIDEO 1 jacks, “Video1” and
DVD
DSS (U.S.A only)
No type
Delete
"VCR" appear in the display.
• Any VIDEO or TV (TV1, TV2, CABLE) inputs that have not been
programmed with a setup code or Non-IR code are deleted from the
cyclic list.
• Select “No type” when the desired source does not appear in the
display.
• The selected input does not appears when you select “Delete.”
When you mistake
7Press the display operation 2 [Enter] key.
• The maker selecting display appears.
Press the display operation 1 [Back] key repeatedly until the display
you want to re-operate appears.
For Europe and U.K
For other countries
Note
Although each setup code is designed to work with a number of different
models, certain codes may not work with some models. (Also, certain
codes may only operate some of the functions available on a given
model.)
>Kenwood
>Admidral
Back Enter
>Kenwood
>Aiwa
Back Enter
Press the 5/∞keys to select the maker you want to
8register.
• Press the 5/∞ keys until the desired maker appears in the display.
When the desired maker does not appear, select “Nothing.”
9Press the display operation 2 [Enter] key.
• The setup code selecting display appears.
>01:0056
>02:Nothing
Back Enter
Press the 5/∞keys to select the setup code.
0
!
Press the AV.POWER
key, and check to see that the
component you want to control turns on.
If the component does not react, and there is more than one
setup code, enter another setup code and try again.
• ‹or TUNING key can also be used instead of the AV. POWER
key.
RemCntrol
• If the component is already on, pressing the AV. POWER
key
will turn it off.
Getting the most from your remote control
Operating other components
Changing (confirming) the operation mode
5
This operation lets you operate the registered components.
KENWOOD audio components with system control turn on and off
automatically with the receiver via the system control connections.
Thisoperationletsyouchangetheremotecontroloperationmodewithout
changing the input selector.
You may find this useful when you want to control one component while
using another. (For example, if you want to rewind the tape deck while
listening to a CD.)
SHIFT
MUSIC, MOVIE,
AV.POWER I /
TV
+
–
+
–
SHIFT
MUSIC, MOVIE,
TV
+
–
+
–
During opration, make sure you start the next step within 8
seconds of completing the previous one. If more than 8
seconds elapses between any two steps, press the display
operation key so that the display appears.
During opration, make sure you start the next step within
8seconds of completing the previous one. If more than 8
seconds elapses between any two steps, press the display
operation key so that the display appears.
Use the MUSIC, MOVIE, or TV key to select the component
you desire.
1
• Pressing the MUSIC or MOVIE key also changes the input selector
on the receiver. If you do not want to change the current input, press
the SHIFT key before step 1.
1Press the SHIFT key.
• “Shift” appears in the display.
MUSIC key
1 CD/DVD
MOVIE key
1 Video1
TV key
1 TV1
Shift
VCR
Menu
2 TV2
3 CABLE
2 TAPE or MD
3 Tuner
4 PHONO
2 Video2
3 Video3
4 DVD 6CH
5 AV AUX
• To operate a TV, start form step 2.
Press the MUSIC, MOVIE, or TV key repeatedly to display
the remote control mode for the component you want to
control.
Press the MUSIC, MOVIE, or TV key until the desired source
appears.
2
Video1:
VCR
Menu
Select source
• You cannot select the source that is not registered.
Shift
DVD
Press the AV. POWER
key.
Menu
2
• The selected component turns on or off.
The component to be controlled
• Pressing any other keys after the SHIFT key cancels the shift function
and sends the normal code associated with the respective key.
• The input selector does not change during this operation.
• If you press MUSIC or MOVIE key more than 3 seconds after
pressing the SHIFT key, the input selector changes together with the
operation mode.
3Press the operation keys you desire.
• See "Remote operation of other components" at the end of this
manual for a list of keys available with each component.
RC!
The remote control mode remains in the set at the component
selected in step 1 mode until you select another component.
3Execute the desired operations.
• See "Remote operation of other components" for a list of keys
available with each component.
RC!
Note
The operation mode remains set at the component specified in
step 2.
To return control to the original component, press SHIFT and
then press the MUSIC or MOVIE key to return to the original
control mode.
Be sure to point the remote control at the remote sensor on the receiver
when you want to operate KENWOOD components connected by
system control cords. Otherwise, point the remote control at the compo-
nent you want to operate.
RmeCntrol
Getting the most from your remote control
Preparing for automatic operations
(MACRO play)
Press the MUSIC, MOVIE, or TV key to select the macro
location. (MACRO1, 2, and 3 respectively)
3
6
• You can store up to 3 different macros, one at each key:
MOVIE ="MACRO 1", MUSIC ="MACRO 2", TV ="MACRO 3"
• The light flashes once when you select the macro location.
• Pressing a key other than MUSIC, MOVIE, or TV cancels the macro
program mode.
The macro play function allows you to set the remote to control several
components in succession. After completing this setup, you can perform
a series of operations automatically. Enter the setup codes for the
components you want to control beforehand.
MACRO1
Select MACRO
Menu
MACRO
MUSIC, MOVIE,
TV
+
–
+
–
When MOVIE is pressed
Press the keys to be operated in order.
4
EXAMPLE:
This example shows you how to create a macro that; turns on the TV,
setstheTVtotheappropriateinput, selectsthereceiver'sinputselector
to LD, and turns on the LD player. All you have to do is insert the laser
disc!
During opration, make sure you start the next step within 8
seconds of completing the previous one. If more than 8
seconds elapses between any two steps, the remote control
unit exits from the MACRO play mode.
1 Press the TV key, then press the AV.POWER
key to turn
on the TV.
1Make a plan of the macro play you want to Setup.
2 Press the F. SHIFT key, then press the "3" (INPUT SEL.) key
The order of the operations may be fairly complex and you may
not be remember all of the necessary commands during the
setup procedure.
to set the TV to the appropriate video input.
Use the space provided below to write down the operations in
the order you are going to enter them.
3 Press the MOVIE key to select the LD player registered at
VIDEO 2.
4 Press the AV.POWER
key to turn on the LD player.
• Up to 20 steps can be memorized for each macro.
• Make sure you start the next operation within 8 seconds of complet-
ingthepreviousone. Ifmorethan8secondselapsesbetweenanytwo
steps, exit the macro programming mode.
• In order to allow verification of the remote control mode, the name of
the selected input appears in the receiver's display when the MUSIC,
MOVIE, or TV key is pressed. When the MUSIC or MOVIE key is
pressed the receiver's input also changes.
1
2
3
4
5
6
7
8
9
0
!
@
#
$
%
^
&
*
(
)
5Press the MACRO key so that the light flashes twice.
• The macro is stored at the locations specified in step 3. If another
macro was previously stored at the same location, it is erased.
• The example below shows the plan for step 4 (which occupies a total
of 6 steps) :
Repeat steps 1 through 5 to program up to 3 macros.
This completes the macro programming procedure.
1 TV + AV. POWER
2 FUNCTION SHIFT + 3
3 MOVIE
2 steps
2 steps
1 steps
1 steps
4 AV. POWER
Total
6 steps
• If you attempt to store more than 20 steps, “Full” appears and exit
the macro programming mode.
• Enter channel numbers (for the monitor TV, etc.) exactly as you would
using the original remote.
• When you select the input by using the MUSIC, MOVIE, or TV key,
it is count 1 step even if you press these keys several times.
RemCntrol
2Press and hold the MACRO key for more than 2 seconds.
• “MACRO MEMORY” appears in the display.
MACRO MEMORY
Select MACRO
Menu
Getting the most from your remote control
Executing an automatic operation
To delete the setup code
7
Display operation 1
Display operation 2
MACRO
5/∞
MUSIC, MOVIE,
TV
+
–
+
–
+
–
+
–
During opration, make sure you start the next step within 8
seconds of completing the previous one. If more than 8
seconds elapses between any two steps, press the display
operation key so that the display appears.
During opration, make sure you start the next step within 8
seconds of completing the previous one. If more than 8
seconds elapses between any two steps, press the display
operation key so that the display appears.
Press the display operation 1 key repeatedly until
1
2
1Press the MACRO key.
“Menu” appears in the display.
• “MACRO EXE” appears in the display.
Video1:
VCR
MACRO EXE
Select MACRO
Menu
Menu
Press the [Menu] key repeatedly until “01.IR” appears
in the display.
Press the MUSIC, MOVIE, or TV key to execute the
2corresponding macro play.
• The setup display appears.
• "MACRO EXE"appearsinthedisplayandthepre-programmedmacro
is performed:
>01.IR
>02.Surround
Home Enter
MUSIC ="MACRO 1", MOVIE ="MACRO 2", TV ="MACRO 3"
• Some devices take up to 1 second to power on. The macro function
has an automatic delay after any power function output.
• Pressing a key other than MUSIC, MOVIE, or TV cancels the macro
program mode.
Press the 5/∞keys to select “01.IR,” then press the
3[Enter] key.
• The input selecting display appears.
MACRO1 EXE
Select MACRO
Menu
>03.Video1
>04.Video2
Back Enter
When MUSIC is pressed
Press the 5/∞keys to select the input that you want to
4delete, then press the [Enter] key.
Press the 5/∞keys to select “Delete.”
5
>13:Delete
>01:CD
Back Enter
6Press [Enter].
• The setup code is deleted.
RmeCntrol
Getting the most from your remote control
4 Press the desired key of the remote control unit.
Storing the remote control cord of the other
components
8
• The remote control is ready for receiving the remote control code.
The remote control unit can store the remote control cord of the other
components and you can operate the other components from the remote
control unit. The remote control cord is stored on the key or memory of
the remote control unit.
Waiting
>Extend1
Clr
Exit
5 Press the key of the same operation that you want to store.
5/∞
Display operation 2
• The remote code is send to the remote control unit.
• “Complete” appears when finished.
MUSIC, MOVIE,
TV
+
–
+
–
Complete
>Extend1
LEARN
• When it takes for more than 5 seconds or the remote control unit does
not receive the remote control code well, “Error” appears in the
display. In this case, re-operate from the step 1.
Storing on the key
You can store the remote control code to the key as shown below:
6 The remote control code is stored on the key of the remote
control unit.
To delete the memory stored on the key
Press the [Clr] key in step 4. “Cleared” appears in the display.
‹ Play
*Pause
&Stop
Tne memory previously stored is cleared.
SHIFT
MACRO
MOVIE
$Rewind/skip
MUSIC
TV
To operate other components
1 Press the MUSIC, MOVIE, or TV key to select desired input
AV. POWER
SYS. POWER
› Fast forward/skip
AV.POWER I /
CH +/-
source.
+
+
Cursor 5/∞/2/3
ENTER
CH.
VOL.
CH.
VOL.
–
–
2 Press the desired key.
MUTE
DIMMER
BASS BOOST
LISTEN M.
SOUND
SUB.W.
MENU
TITLE/GUIDE
TUNING
TITLE/GUIDE
RETURN/PAGE
REC
MENU
BAND
ENTER
RETURN
/PAGE
OSD
/PAGE
AUTO/MONO
F.SHIFT
OSD/PAGE
Storing on the memory
REC
LEARN
REPEAT
1
RANDOM
2
INPUT SEL.
3
TV SELECT
4
DISPLAY
5
SELECT
6
You can store on the remote control unit up to 5 memories.
AUDIO
7
THEME
8
FAVORITE
9
Numeric keys
INFO.
+10
EXIT
0
LAST CHANNEL
+100
1 Point the infrared ray system part of the other remote control
10
11
12
unit to the remote sensor of the remote control unit .
Remote control
unit of the other
source.
1 Pointtheinfraredraysystempartofanotherremotecontrolunit
to the remote sensor of the remote control unit .
Infrared ray system part
Remote control
unit of the other
source.
2 Press the MUSIC, MOVIE, or TV key to select the input of the
desired remote control unit.
Infrared ray system part
Video1:
VCR
2 Press the MUSIC, MOVIE, or TV key to select the input of the
desired remote control unit.
Menu
Selected input
Video1:
VCR
3 Press the LEARN key.
• The Extend selecting display appears.
Menu
Selected input
When the setup code is registered
3 Press the LEARN key.
RemCntrol
>Extend1
>Extend2
Home Enter
When the setup code is registered
>Extend1
>Extend2
Home Enter
• When the setup code is not registered, any messages do not appear.
• When the setup code is not registered, any messages do not appear.
Getting the most from your remote control
4 Press the 5/∞keys to select the location.
Restoring the original factory settings
9
• Extend1 – Extend5 are available.
You can restore the setup codes or memories to their original default
settings.
5 Press the [Enter] key.
• The remote control is ready for receiving the remote control code.
5
Waiting
>>EExxtteenndd11
+
–
+
–
Clr
Exit
TUNING
BAND
ENTER
6 Press the key of the same operation that you want to store.
• The remote code is send to the remote control unit.
• "Complete" appears when finished.
Complete
>Extend1
Insert the batteries during pressing and holding the [5]
2
keys and [
] key.
1
Extend
1
• "Cleared" appears in the display, and the remote settings return to
their original default settings.
• When it takes for more than 8 seconds or the remote control unit does
not receive the remote control code well, "Error" appears in the
display. In this case, re-operate from the step 1.
• "Full" appears when the memory is full. Re-operate from the step
1 after deleting some memories.
7 The remote control code is stored on the memory (Extend1 –
Extend5) of the remote control unit.
To delete the stored memory
Press the [Clr] key in step 5. "Cleared" appears in the display
and the memory that is selected in step 4 is erased.
To operate other components by using the stored memory
1 Press the MUSIC, MOVIE, or TV key to select desired input
source.
• The Menu display appears.
2 Press the [Menu] key .
3 Press the 5/∞keys to select the memory you want to operate.
4 Press the [Enter] key.
RmeCntrol
Getting the most from your remote control
Displaying the CD TEXT data
4 Press the [Text] key.
10
When you connect a KENWOOD CD player (CD-425M, CD-4700M, CD-
4260M, DPF-J6030), you can display the CD TEXT data in the display of
the remote control unit.
• The display for selecting disc appears.
>050.D.Title
>051.
Home Sel
Press the 5/∞keys to select the desired disc, then press
Display operation 1
Display operation 2
5
5/∞
the [Sel] key.
+
–
+
–
>01.T.Title
>02.T.Title
Back Sel
Press the 5/∞keys to select the desired track, then press
6 the [Sel] key.
Before operation, regiser the setup code of the CD player.
1Load the CD TEXT data to the CD player.
1 Press the MUSIC key to select "CD".
2 Press the [Menu] key repeatedly until "SetUp" appears in the
display.
3 Press the 5/∞keys to select "All Read" and press the [Enter]
key.
• The loading time may take a few moments.
Load the CD TEXT data of the CD player to the remote
control unit.
2
1 Press the MUSIC key to select "CD".
2 Press the [Menu] key repeatedly until "SetUp"s appears in the
display.
3 Press the 5/∞ keys to select "Disc Title" and press the
[Enter] key.
• The remote control unit starts reading the CD TEXT data (disc titles
are also read).
•
appears during reading.
3 Press the [Home] key.
• "Text" appears when the CD TEXT data is read.
CD/DVD
CD
Text Menu
• When "Text" does not appears, select "Track Title" in the
"SetUp" display and press the [Enter] key.
RemCntrol
Remote operation of other components
You can operate other components by pressing keys or using the display.
The setup code for each component must be entered beforehand.
RC3
11
When you operate by using the keys
• To execute a FUNCTION SHIFT command written above the numeric
keys, press the F. SHIFT key, then press the corresponding key.
• When pressing keys in succession, press each key firmly and be sure to
wait at least 1 second before pressing the next key.
1 Press the MUSIC, MOVIE, or TV key to select the component
you want to control.
2 Press the keys corresponding to the operations you desire.
When you operate by using the display
Notes
1. Although each setup code is designed to work with a number of different
models, certain codes may not work with some models. (Also, certain
codes may only operate some of the functions available on a given
model.)
2. The charts below show the typical functions available for each compo-
nent. Some manufacturers use different key combinations to perform
similar functions.
1 Press the MUSIC, MOVIE, or TV key to select the component
you want to control.
2 Press the display operation 2 [Menu] key so that the Menu
display appears.
3 Press the 5/∞ keys to select desired item or memory, then
press the display operation 2 [Enter] key.
Tuner operations
Cassette deck operations
TUNING
TUNING
REPEAT
1
RANDOM
2
INPUT SEL.
3
Display operation
01-05: Extend 1 - 5
BAND
BAND
TV SELECT
4
DISPLAY
5
SELECT
6
ENTER
ENTER
AUDIO
7
THEME
8
FAVORITE
9
AUTO/MONO
AUTO/MONO
INFO.
+10
EXIT
0
LAST CHANNEL
+100
10
11
12
‹ (Play A)
ENTER (Play B)
8 (Pause B)
REC
$
* (Pause A)
BAND
(P. CALL fi)
›
& (Stop A)
$ (Rewind A)
› (Fast forward A)
7 (Stop B)
AUTO/MONO
TUNING 2
TUNING 3
REC (Recording)
Numeric keys
1 (Rewind B)
¡ (Fast forward B)
(P. CALL %)
FUNCTION SHIFT commands
‹ (Reverse play A), ENTER (Reverse play B)
CD player operations
Display operation
REPEAT
1
RANDOM
2
INPUT SEL.
F.SHIFT
TUNING
3
REPEAT
1
RANDOM
2
INPUT SEL.
3
TV SELECT
4
DISPLAY
5
SELECT
6
+
01: Disc Sel
02: Set
BAND
CH.
ENTER
TV SELECT
4
DISPLAY
5
SELECT
6
CH.
AUDIO
7
THEME
8
FAVORITE
9
–
AUDIO
7
THEME
8
FAVORITE
9
INFO.
+10
EXIT
0
LAST CHANNEL
+100
03: P.Mode
04: Check
05: Clear
06: Disc Title
07: Track Title
08: All Read
09: Subout Monitor
10: Continuous Play
11: All Info.
INFO.
+10
EXIT
0
LAST CHANNEL
+100
10
11
12
‹ (Play)
+
1 (Rewind)
¡ (Fast forward)
FUNCTION SHIFT
commands
REPEAT
RANDOM
DISPLAY
* (Pause)
& (Stop)
(DISC SKIP %)
Numeric keys
$ (Skip)
› (Skip)
12-16: Extend1-5
MD recorder operations
REPEAT
1
RANDOM
2
INPUT SEL.
3
F.SHIFT
TUNING
Display operation
01-05: Extend1-5
REPEAT
1
RANDOM
2
INPUT SEL.
3
TV SELECT
4
DISPLAY
5
SELECT
6
REC
BAND
ENTER
TV SELECT
4
DISPLAY
5
SELECT
6
AUDIO
7
THEME
8
FAVORITE
9
AUDIO
7
THEME
8
FAVORITE
9
INFO.
+10
EXIT
0
LAST CHANNEL
+100
REC
(Recording)
INFO.
+10
EXIT
0
LAST CHANNEL
+100
10
11
12
‹ (Play)
* (Pause)
& (Stop)
$ (Skip)
› (Skip)
1 (Rewind)
¡ (Fast forward)
FUNCTION SHIFT
commands
REPEAT
Numeric keys
RmeCntrol
RANDOM
DISPLAY
Remote operation of other components
TV operations
12
REPEAT
1
RANDOM
2
INPUT SEL.
3
TUNING
F.SHIFT
Display operation
01: -/--
02: >12
+
REPEAT
1
RANDOM
2
INPUT SEL.
3
CH.
BAND
TV SELECT
4
DISPLAY
5
SELECT
6
ENTER
CH.
TV SELECT
4
DISPLAY
5
SELECT
6
AUDIO
7
THEME
8
FAVORITE
9
–
AUDIO
7
THEME
8
FAVORITE
9
AUTO/MONO
INFO.
+10
EXIT
0
LAST CHANNEL
+100
CHANNEL +
CHANNEL -
INFO.
+10
EXIT
0
LAST CHANNEL
+100
03: Wide
Cursor
5/∞/2/3
ENTER
10
11
12
04: Picture in Picture
05: Text/Mix/TV
06: Text Off
07: Mix
08: Exit
09-13: Extend1-5
Numeric keys
FUNCTION SHIFT
commands
INPUT SEL.
TV SELECT
AUDIO
VOLUME + ›
VOLUME - $
& (Mute)
VCR operations
REPEAT
1
RANDOM
2
INPUT SEL.
3
F.SHIFT
Display operation
01: Thumb Up
02: Thumb Down
03: Jump
04: Instant
Replay
05: Quick Skip
06: Exit
07-11: Extend1-5
+
CH.
REPEAT
1
RANDOM
2
INPUT SEL.
3
TV SELECT
4
DISPLAY
5
SELECT
6
CH.
–
TV SELECT
4
DISPLAY
5
SELECT
6
AUDIO
7
THEME
8
FAVORITE
9
AUDIO
7
THEME
8
FAVORITE
9
INFO.
+10
EXIT
0
LAST CHANNEL
+100
CHANNEL +
CHANNEL -
INFO.
+10
EXIT
0
LAST CHANNEL
+100
‹ (Play)
* (Pause)
& (Stop)
10
11
12
TUNING
Numeric keys
FUNCTION SHIFT
commands
INPUT SEL.
BAND
ENTER
$ (Skip)
› (Skip)
MENU
AUTO/MONO
Cursor
5/∞/2/3
ENTER
TITLE/GUIDE
MENU
REC
REC (Recording)
TITLE/GUIDE
LD player operations
REPEAT
1
RANDOM
2
INPUT SEL.
3
F.SHIFT
Display operation
01: Frame/Time
02: Side A or A/B
03: Side B
+
REPEAT
1
RANDOM
2
INPUT SEL.
3
CH.
TV SELECT
4
DISPLAY
5
SELECT
6
CH.
TV SELECT
4
DISPLAY
5
SELECT
6
–
AUDIO
7
THEME
8
FAVORITE
9
AUDIO
7
THEME
8
FAVORITE
9
INFO.
+10
EXIT
0
LAST CHANNEL
+100
+ (Slow)
- (Slow)
INFO.
+10
EXIT
0
LAST CHANNEL
+100
‹ (Play)
* (Pause)
& (Stop)
$ (Skip)
› (Skip)
10
11
12
04-08: Extend1-5
Numeric keys
FUNCTION SHIFT
commands
REPEAT
TUNING
BAND
OSD
/PAGE
ENTER
RANDOM
DISPLAY
OSD/
PAGE
ENTER
1
(Rewind)
¡ (Fast forward)
DVD player operations
REPEAT
1
RANDOM
2
INPUT SEL.
3
F.SHIFT
Display operation
01: Chapter/Time
02: Angle
+
CH.
REPEAT
1
RANDOM
2
INPUT SEL.
3
TV SELECT
4
DISPLAY
5
SELECT
6
CH.
–
TV SELECT
4
DISPLAY
5
SELECT
6
AUDIO
7
THEME
8
FAVORITE
9
AUDIO
7
THEME
8
FAVORITE
9
INFO.
+10
EXIT
0
LAST CHANNEL
+100
03: PGM
+ (Fast forward)
INFO.
+10
EXIT
0
LAST CHANNEL
+100
‹ (Play)
* (Pause)
& (Stop)
10
11
12
04: DVD Set
05: Memory
06: Clear
07: Repeat A-B
08: Sub Title
09: Title Search
10: Aspect
- (Rewind)
Numeric keys
FUNCTION SHIFT
commands
RANDOM
REPEAT
DISPLAY
RemCntrol
TUNING
$ (Skip)
› (Skip)
MENU
BAND
ENTER
MENU
TITLE/GUIDE
AUTO/MONO
OSD
/PAGE
Cursor
5/∞/2/3
ENTER
RETURN
/PAGE
AUDIO
11: On/Off
12-16: Extend1-5
OSD/
PAGE
RETURN
GUIDE
Remote operation of other components
DSS receiver operations
13
TUNING
REPEAT
1
RANDOM
2
INPUT SEL.
3
MENU
F.SHIFT
Display operation
REPEAT
1
RANDOM
2
INPUT SEL.
3
+
BAND
TV SELECT
4
DISPLAY
5
SELECT
6
CH.
ENTER
01: Exit
CH.
TV SELECT
4
DISPLAY
5
SELECT
6
AUDIO
7
THEME
8
FAVORITE
9
–
MENU
02-06: Extend1-5
AUTO/MONO
AUDIO
7
THEME
8
FAVORITE
9
INFO.
+10
EXIT
0
LAST CHANNEL
+100
INFO.
+10
EXIT
0
LAST CHANNEL
+100
Cursor
5/∞/2/3
ENTER
CHANNEL +
CHANNEL -
10
11
12
FUNCTION SHIFT
commands
INPUT SEL.
SELECT
TITLE/GUIDE
Numeric keys
CHANNEL
GUIDE
AUDIO
THEME
FAVORITE
INFO.
Cable tuner operations
TUNING
REPEAT
1
RANDOM
2
INPUT SEL.
3
MENU
F.SHIFT
Display operation
REPEAT
1
RANDOM
2
INPUT SEL.
3
+
BAND
TV SELECT
4
DISPLAY
5
SELECT
6
CH.
ENTER
01: A - B - C
CH.
TV SELECT
4
DISPLAY
5
SELECT
6
AUDIO
7
THEME
8
FAVORITE
9
–
MENU
04-08: Extend1-5
AUTO/MONO
AUDIO
7
THEME
8
FAVORITE
9
INFO.
+10
EXIT
0
LAST CHANNEL
+100
INFO.
+10
EXIT
0
LAST CHANNEL
+100
Cursor
5/∞/2/3
ENTER
CHANNEL +
CHANNEL -
10
11
12
FUNCTION SHIFT
commands
INPUT SEL.
SELECT
TITLE/GUIDE
Numeric keys
GUIDE
RETURN
/PAGE
OSD
/PAGE
THEME
VOLUME + ›
VOLUME - $
FAVORITE
INFO.
EXIT
PAGE DOWN (fi)
PAGE UP (%)
LAST CHANNEL
Satellite tuner operations
TUNING
OSD
/PAGE
REPEAT
1
RANDOM
2
INPUT SEL.
3
F.SHIFT
Display operation
01-05: Extend1-5
+
BAND
REPEAT
1
RANDOM
2
INPUT SEL.
3
TV SELECT
4
DISPLAY
5
SELECT
6
CH.
ENTER
CH.
TV SELECT
4
DISPLAY
5
SELECT
6
AUDIO
7
THEME
8
FAVORITE
9
–
OSD
AUTO/MONO
AUDIO
7
THEME
8
FAVORITE
9
INFO.
+10
EXIT
0
LAST CHANNEL
+100
INFO.
+10
EXIT
0
LAST CHANNEL
+100
Cursor
5/∞/2/3
ENTER
CHANNEL +
CHANNEL -
10
11
12
FUNCTION SHIFT
commands
INPUT SEL.
SELECT
Numeric keys
AUDIO
RmeCntrol
In case of difficulty
Remote control unit
14
Symptom
Cause
Remedy
The battery indicator flashes during opera-
tion.
• The batteries are nearing exhaustion.
• Replace with new batteries to preserve the
currently registered setup information.
$
Subwoofer volume cannot be adjusted.
• Subwoofer is OFF.
• Turn the subwoofer ON.
%
Certain inputs cannot be selected using the
remote control.
• No setup codes registered at for the respec-
tive input(s).
• Register a setup code or Non-IR code at the
respective input(s). RC3
Remote control operation is not possible.
• The remote control is set to a different
operation mode.
• Press the MUSIC, MOVIE, or TV keys to
select the appropriate operation mode.
• Batteries are exhausted.
• Replace with new batteries.
• Operate the remote control unit within the
controllable range.
$
• The remote control unit is too far away from
the main system, controlling angle is too
large, or there is an obstacle between the
receiver and the remote.
• The audio cords and system control cords are • Connect properly referring to “Setting up the
not connected properly.
• No software is loaded in the source
component.
system”.
8
• Place software in the source component you
want to play.
• Wait until recording has completed.
• An attempt is made to play a tape which is
being recorded in the cassette deck.
• The remote control has not been set to the
operation mode for the component you wish
to control.
• Press the MUSIC, MOVIE, or TV keys to
activate the operation mode for the
component you want to control before
operation.
RC5
• The microprocessor of the remote control
malfunctions.
• Reset the microprocessor.
§
RemCntrol
|