UDR-Stereo Receiver
UDS-Stereo Sender
UR-Stereo Receiver
US-Stereo Sender
Stereo Balun Specifications:
Models and Dimensions:
UDR-Stereo (in-wall Decora™ version): 4.1"h x 1.4" w x 2.0"d.
UDS-Stereo (in-wall Decora™ version): 4.1"h x 1.4" w x 2.0"d.
UR-Stereo (black enclosure): 1.1"h x 2.6"w x 2.8"d (28 x 66 x 71 mm).
US-Stereo (black enclosure): 1.1"h x 2.6"w x 2.8"d (28 x 66 x 71 mm).
Installation Instructions v1.1
Input and Outputs:
Warning: To be installed and/or used in accordance with
appropriate electrical codes and regulations. If you are not sure
about any part of these instructions, consult a qualified
electrician.
Send Unit: two stereo input RCA jacks, one 3.5mm mono
infrared emitter jack, one RJ-45 out-jack, one-DC power input.
Receive Unit: Three RCA output jacks, one RJ-45 in-jack, one-
DC power input.
Audio Input Impedance:
Receive Unit: 20k ohms, max 3 Vp-p.
Frequency Response: 10Hz-50kHz +/- 3 dB
Caution: Do not install this product in an electrical junction box
with 110V or higher unless an approved barrier separates the
high and low voltage sections.
Power:
Introduction: Thank you for your purchase of a Knoll active
balun system. This system is specifically designed to send a
stereo line level and an infrared signal safely down a cat 5 or cat
5e wire up to 1000 feet without encountering noise problems.
Balun is an acronym for:
Send Unit: 12 VDC unregulated (one PS1202 will power one
each send and receive).
Receive Unit: 12 VDC unregulated (one PS1202 will power one
each send and receive).
Infrared:
BALance – UNbalance
Send Unit: One stereo 3.5mm jack to connect one single or one dual
emitter.
The send module takes a conventional stereo line level signal
and balances it (signal is not tied to a ground reference) then
sends it via cat 5 to the receive module (with power from the
send module). The receive module unbalances the stereo signal
back to its former state. This process does not allow any stray
magnetism of any sort to contaminate the signal while it is
being transported.
Receive Unit: One triple 3.5 mm jack to connect a three wire Knoll or
other infrared receiver. Supplies 12 VDC power for infrared receiver
without requiring another power supply.
Warranty
Knoll Systems warrants balun products sold in the USA and Canada by
authorized Knoll dealers to be free of defects in materials and workmanship.
This warranty extends for three full years from the date of purchase by the
original consumer. Any products returned to Knoll Systems and found to be
defective by Knoll Systems within the warranty period will be repaired or
replaced at Knoll System’s option, at no charge. Knoll Systems will not be
responsible for the actual cost of installation or removal of the product, nor for
any incidental or consequential damages. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above
limitation may not apply to you. This warranty gives you specific legal rights.
You may have additional legal rights that vary from state to state.
Features:
•
•
•
•
•
Tabletop box design or Decora™ style available.
Safely sends stereo signals up to 1000’ (300 m).
Sends infrared signal from receiver back to sender.
PS1202 power supply required on send side only.
Mix and match tabletop and decora style.
145 Tyee Drive Point Roberts, WA 98281
12140 Horseshoe Way, Richmond BC V7A 4V4
tel (604) 272 4555, fax (604) 272 5595
Made in Canada Knoll Systems All Rights Reserved
|