6
A3 Laminator ULG 300 A1
A3 Laminator
Operating instructions
KOMPERNASS GMBH
BURGSTRASSE 21 · D-44867 BOCHUM
ID-Nr.: ULG300A1-04/10-V2
IAN: 61862
Content
Page
1. Intended use
2
2
2
2
3
4
4
5
6
6
7
7
7
8
8
8
9
2. Items supplied
3. Appliance description
4. Technical Data
5. Safety instructions
6. Suitable laminating pouches
7. Operating levels
8. Preparing for hot lamination
9. Preparing for cold lamination
10. Lamination process
11. Anti-Blocking Switch (ABS)
12. Trimming function
13. Cleaning and care
14. Storage
15. Disposal
16. Warranty and Service
17. Importer
Read the operating instructions carefully before using the appliance for the first time and preserve this
booklet for later reference. Pass the manual on to whomsoever might acquire the appliance at a later date.
- 1 -
A3 Laminator
3. Appliance description
Foil guide rails (rear)
Cutting rail
Cutting head
q
w
e
r
t
y
u
i
1. Intended use
This laminator is intended exclusively for use in priva-
te households and for the hot and cold lamination
of documents printed on paper or cardboard.
Additionally, the documents can be trimmed.
It is NOT intended for use with any other materials.
It is also NOT intended for commercial or industrial
applications.
Foil format restraint
Slot for manual foil feed
Indicator lamp "Ready"
ON/OFF Indicator lamp
Selector switch for hot and cold lamination
(HOT and COLD)
Anti-blockage switch and foil thickness switch
Foil slot (front)
Document support
o
a
s
d
The warranty does not provide compensation for
damage caused by improper use of the appliance!
Cutter attachment
2. Items supplied
4. Technical Data
1x Laminator with pluggable cutter attachment
8x DIN A3 size Laminating pouches for hot lamina-
tion (80 microns)
Rated voltage:
Current consumption: 1.4 A
Power consumption:
Lamination speed:
220 - 240 V 50 Hz
~
300 W
1x Operating instructions
Sheet size
80 Micron
125 Micron
A4
A3
approx. 52 s approx. 70 s
approx. 75 s approx. 105 s
Foil width:
max. 320 mm
Foil thickness hot lamination:
Foil thickness cold lamination: max. 200 Mikron
Protection class: II/
max. 125 Mikron
Cutting capacity of the cutter attachment
max. 3 Sheets of 80g/m2 or a laminated document
:
d
(80 micron).
- 2 -
Overheating Protection
• Do NOT laminate any document which, together
with the laminating pouch, would have a thickness
of more than 1,0 mm. Should you do so, the lami-
nating pouch could cant itself inside the laminating
appliance. This would damage the laminating pouch,
the document being laminated as well as the
laminator.
• Do not use an extension cable. Place the appliance
where the mains power socket is easily accessible,
so that in the event of an emergency the plug can
be quickly withdrawn.
This appliance is fitted with overheating protection.
Should the motor become too hot due to excessive
loading, the appliance switches itself off automati-
cally. In this case, disconnect the plug from the
mains power socket and wait until the appliance
has cooled down to room temperature. You can
then reconnect the plug to the mains power socket
and continue using the appliance. We recommend
that, after 2 hours continuous use, you allow the ap-
pliance to cool down for about 30 minutes.
• Do not use an external timing switch or a separate
remote control system to operate the appliance.
• Place the appliance where the power wall socket
is easily accessible, so that in the event of an
emergency the plug can be quickly withdrawn.
5. Safety instructions
• This appliance is not intended for use by individuals
(including children) with restricted physical, physio-
logical or intellectual abilities or deficiences in
experience and/or knowledge unless they are
supervised by a person responsible for their safety
or receive from this person instruction in how the
appliance is to be used.
ƽ Risk of electrical shock!
• Connect the appliance to a mains power socket
with a mains voltage of 220-240 V 50 Hz.
~
• Do not take the appliance into use if the power
cable or the plug is damaged.
• Children should be supervised to ensure that they
do not play with the appliance.
• Unplug the power cable after every use and be-
fore cleaning, so as to prevent the appliance from
inadvertently switching itself on.
• Arrange for defective power plugs and/or cables
to be replaced at once by qualified technicians
or our Customer Service Department.
• NEVER immerse the appliance in water.
Wipe it only with a damp cloth.
• Check the appliance and all parts for visible
damages. The safety concept can work only if
the appliance is in a faultless condition.
• Never perform hot lamination on flammable,
heat-sensitive and/or meltable materials and do
not laminate drawings on temperature-sensitive
paper or material that will undergo changes in
colour or quality when subjected to heat.
• Never laminate valuable or unique documents.
Although the laminator satisfies all predominant
safety norms and standards, errors can never be
completely discounted - as with all electrical ap-
pliances. Errors with the laminator can result in
damage to the document being laminated.
• Do not expose the appliance to rain and never
use it in a humid or wet environment.
• Ensure that the power cable never becomes wet
during operation.
• Unplug the appliance immediately after use.
The appliance is free of electricity only when you
remove the plug from the mains power socket.
• Do not open the housing or attempt to repair the
appliance yourself. Should you do so, device safety
can no longer be assured and the warranty will
become void.
- 3 -
ƽ Risk of fire!
6. Suitable laminating pouches
• Do not use the appliance in the vicinity of hot
surfaces.
• For hot lamination you can use pouches with a
width of up to 230 mm and a maximum thickness
of 125 micron.
• Do not place the appliance at locations exposed
to direct sunlight.
This could lead to overheating and cause irrepa-
rable damage.
• Please note that each laminating pouch may only
be used once.
• Do not leave the appliance unattended when in
use.
• NEVER cover the ventilation slits on the top of the
appliance while it is switched on.
ꢀ For hot lamination, use only laminating
pouches that are expressly designated
for hot lamination.
For cold lamination, use only laminating
pouches that are expressly designated
for cold lamination.
ƽ Risk of injury!
•
Keep children away from the connecting cable and
the appliance. Children frequently underestimate the
dangers of electrical devices.
ꢀ Take note that the laminating pouches in-
cluded with the laminator are intended
exclusively for hot lamination.
• Ensure that the appliance stands with a safe and
secure positioning.
• Do not operate the appliance if it has sustained
a fall or is damaged. Arrange for the appliance
to be checked and, if necessary, repaired by a
qualified expert.
• Some parts of the appliance become very hot
during operation. To avoid burns, do not touch
these parts.
7. Operating levels
Position of
Laminating foil
Position of
pouch thickness
selector switch
i
thickness
switch
o
HOT
80
> 60 - 80
HOT
Cold
125
125
85 - 125
to 200
Tip: For high-gloss photos, you should select the switch
position “125” as well as the appropriate
pouch thickness.
- 4 -
8. Preparing for hot lamination
ꢀ Make certain that all corners of the docu-
ment have at least two millimetres of space
to the edge of the laminating pouch, as
shown in Fig. 1. Make certain that you use
only one pouch for laminating. First open
it up, as shown in Fig. 2.
➩ Insert the foil guide rails in the designated
q
holes on the rear of the laminator.
➩ Fold out the document supports , so that the
s
documents can be pulled in straight into the slot
for manual foil feed
.
t
➩ Insert the plug of the laminator into a mains
power socket.
Fig. 1
➩ Provide a firm location for the appliance.
➩ Set the selector switch for hot and cold lamina-
tion
to "HOT ".
i
➩ Set the foil thickness switch to the desired foil
o
thickness (80 or 125 microns). The red ON/OFF
indicator lamp
will now glow. The lami-
u
nator heats itself up to its operating temperature.
•
As soon as the green indicator lamp "Ready"
glows, the laminator has reached its
ꢀ For information about the lamination
y
operating temperature.
process, please read section 10.
ꢀ Attainment of the operating temperature
Fig. 2
is indicated by the lighting up of the green
LED indicator lamp "Ready"
. For a
y
more uniform laminating result we recom-
mend, especially for thinner foils (below
125 Micron) and after adjustment to a dif-
ferent foil thickness, to first wait an addi-
tional 2-3 minutes before beginning with
lamination.
➩ Lay the document to be laminated into a lami-
nating pouch of the appropriate size.
- 5 -
9. Preparing for cold lamination 10. Lamination process
ꢀ If you have previously performed hot lami-
nation:
➩Lay the laminating pouch onto the pouch guide
.
q
Lay the right or left edge of the laminating pouch
After hot laminating, allow the laminator
to cool down completely before beginning
with cold lamination. Remember, the rollers
inside the laminator will still be hot. These
can damage the laminating pouch and the
document to be laminated!
against the pouch format lock (closed side
r
leading). Slide the pouch format lock together
r
until the selected format size is reached. This pre-
vents the laminating pouch from being pulled in
at an angle.
ꢀ Should the laminating pouch be pulled in
at an angle, use the "Anti-Blocking Funk-
tion" as described in chapter 11.
➩ Insert the foil guide rails in the designated
q
holes on the rear of the laminator.
➩ Pull out the document supports so that the
s
documents can be pulled in straight into the slot
➩Now slide the laminating pouch slowly into the
for manual foil feed
.
slot for manual pouch input
.
t
t
➩ Insert the plug of the laminator into a mains
power socket.
➩When you have slid the laminating pouch several
➩ Provide a firm location for the appliance.
➩ Set the selector switch for hot and cold lamina-
centimetres into the slot , it will start to be pulled
t
in automatically. Release the laminating pouch
as soon as you notice it being pulled in auto-
matically.
tion
to "COLD".
i
ꢀ Take note: For cold lamination, ALWAYS place
the foil thickness switch at 125 microns.
ꢀ Ensure there is at least 45 cm of open space
in front of the laminator. If you do not, the
laminating pouch will not be completely
ejected from the laminator after lamina-
tion. This could damage the laminated
pouch.
o
The red ON/OFF indicator lamp
the green indicator lamp "Ready"
now glow.
and
u
y
➩ Place the document to be laminated into a
laminating pouch of the matching size.
➩The finished laminated pocket is now ejected
ꢀ Make certain that all corners of the docu-
ment have at least two millimetres of space
to the edge of the laminating pouch, as
shown in Fig. 1.
ꢀ Make certain that you use only one pouch
for laminating. First open it up, as shown
in Fig. 2.
from the foil slot
Only after hot lamination:
➩Remove them immediately from the appliance,
as hot foil pockets can still be easily deformed.
Place them on a flat surface to cool down.
of the laminator.
a
ꢀ To improve the lamination result, you can
weigh down the still hot foil bag with a
book, a file folder or other heavy, smooth
object. This will give it a smooth and flaw-
less surface.
ꢀ For information about the lamination pro-
cess, please read section 10.
- 6 -
➩If you do not want to start another lamination
process, turn the foil thickness switch to ABS
➩ Hold the paper in a secure position with your
left hand.
o
(OFF) and withdraw the plug from the mains
power socket.
➩ To trim, press the cutting head down with
e
the right hand and then slide it with one pull or
push over the document.
11. Anti-Blocking Switch (ABS)
13.Cleaning and care
At the start of the lamination process, the pouch
may be pulled in at an angle or jam itself inside the
appliance.
Potentially fatal electrical shock:
• Never open the appliance housing. There
are no user-serviceable elements inside.
• Never submerse the appliance into water
or other liquids!
➩ Turn the anti-blocking switch (ABS) to the
o
position ABS.
•
The laminate pouch is not pulled any further in.
Cleaning the housing:
➩ Remove the laminate pouch.
➩ Turn the anti-blocking switch (ABS) back to
ꢀ Clean the surface of the housing with a
o
the desired foil thickness.
slightly moistened cleaning cloth.
➩ Re-start the lamination process.
➩ First remove the plug.
➩ Allow the appliance to cool down completely.
➩ Ensure that no moisture can permeate into the
appliance.
12. Trimming function
Should you wish to use the trimming function on the
pouch guide , dismantle the pouch guide
.
Cleaning the interior of the appliance:
q
q
➩ If necessary, fold the documents supports
With every lamination, contaminants are deposited
on the rollers inside the laminator. Over time, this re-
duces the performance of the laminator. You should
therefore clean the rollers inside the laminator after
use.
s
down.
➩ Adjust the cutter attachment so that it forms
d
a straight face with the foil guide rails
.
q
➩ Slide the cutting head to the end stop (the
e
cutting head
can be slid to both ends of the
e
cutting rail ).
➩ Flap the cutting rail upwards with the rounded
➩ Prepare the appliance as described in Chapter
8 "Preparing for hot lamination", up to the point
where the green indicator lamp "Ready"
w
w
grip and position the document on the pouch
guide . Restrain the document by sliding the
glows.
q
y
pouch format locks
together until they touch
r
both sides of the document.
➩ Use the markings on the measurement table to
align the document precisely.
➩ Flap the cutting rail downwards so that it
w
engages.
- 7 -
➩ Then run a sheet of DIN A3 paper, folded in
15. Disposal
the middle (maximum thickness 1.0 mm) …
Do not dispose of the appliance with
• without a laminating pouch and
• with the fold first
your normal domestic waste. This
product is subject to the provisions of
European Directive 2002/96/EC.
… slowly into the slot for manual pouch input
.
t
Dispose of the appliance through an approved waste
disposal centre or at your community waste facility.
Observe the currently applicable regulations.
In case of doubt, please contact your waste disposal
centre.
➩ Release the sheet as soon as you notice it
being pulled in automatically.
• The contaminants on the rollers inside the lami-
nator now firmly attach themselves to the sheet
of paper. The paper is discharged from the foil
Dispose of all packaging materials in an
environmentally friendly manner.
slot
of the laminator.
a
➩ Repeat this cleaning process several times.
Use a fresh clean sheet of paper each time.
When you no longer see any contaminants on
the paper, the rollers inside the laminator are
clean.
16. Warranty and Service
The warranty for this appliance is for 3 years from
the date of purchase. The appliance has been ma-
nufactured with care and meticulously examined be-
fore delivery. Please retain your receipt as proof of
purchase. In the event of a warranty claim, please
make contact by telephone with our Service Depart-
ment. Only in this way can a post-free despatch for
your goods be assured.
14. Storage
Allow the appliance to cool down completely
before putting it into storage.
ꢀ Do not store the laminator in damp loca-
tions where moisture could enter inside
the appliance (e.g. cellars)!
The warranty covers only claims for material and
maufacturing defects, but not for transport damage,
for wearing parts or for damage to fragile compo-
nents, e.g. buttons or batteries. This product is for
private use only and is not intended for commercial
use. The warranty is void in the case of abusive and
improper handling, use of force and internal tampe-
ring not carried out by our authorized service
branch. Your statutory rights are not restricted in
any way by this warranty.
The warranty period will not be extended by repairs
made under warranty. This applies also to replaced
and repaired parts. Any damage and defects extant
on purchase must be reported immediately after un-
packing the appliance, at the latest, two days after
the purchase date. Repairs made after the expira-
tion of the warranty period are subject to payment.
- 8 -
DES UK LTD
Tel.: 0871 5000 700 (£ 0.10 / minute)
E-Mail: [email protected]
17. Importer
KOMPERNASS GMBH
BURGSTRASSE 21
Kompernass Service Ireland
Tel.: 1850 930 412 (0,082 EUR/Min.)
Standard call rates apply. Mobile operators may vary.
E-Mail: [email protected]
D-44867 BOCHUM, GERMANY
- 9 -
|