LG Electronics Car Satellite TV System 20 23LS7DC User Manual

20/23LS7DC, 26/32LC7DC, 42/50PC5DC, 60PC1DC  
Integrated TVs  
PUBLIC DISPLAY MODE SETUP  
How to use the TLL-1100A TV-Link Loader  
to copy and clone a Master TV setup is  
provided in the operation manual supplied  
with the TV-Link Loader  
Note: Prior to cloning the Public Display Mode  
Setup, be sure to set up all the other TV features  
that should be included in the master TV setup.  
This includes channel adding-deleting, video and  
audio menu setups and other TV features that are  
clonable. Refer to the TV installation guide for  
specific details.  
P/NO : MFL34797021 (0707-REV01)  
Printed in Korea  
 
SAFETY INSTRUCTIONS  
IMPORTANT SAFETY INSTRUCTIONS  
Important safety instructions shall be provided with each apparatus. This information shall be given in a separate  
booklet or sheet, or be located before any operating instructions in an instruction for installation for use and  
supplied with the apparatus.  
This information shall be given in a language acceptable to the country where the apparatus is intended to be used.  
The important safety instructions shall be entitled “Important Safety Instructions. The following safety  
instructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safety  
information may be included by adding statements after the end of the following safety instruction list. At the  
manufacturer’s option, a picture or drawing that illustrates the intent of a specific safety instruction may be  
placed immediately adjacent to that safety instruction:  
Do not defeat the safety purpose of the polarized  
or grounding-type plug. A polarized plug has  
two blades with one wider than the other. A  
grounding type plug has two blades and a third  
grounding prong, The wide blade or the third  
prong are provided for your safety. If the provided  
plug does not fit into your outlet, consult an  
electrician for replacement of the obsolete outlet.  
Read these instructions.  
Keep these instructions.  
Heed all warnings.  
5
Follow all instructions.  
Do not use this apparatus near water.  
1
Clean only with dry cloth.  
2
Protect the power cord from being walked on  
or pinched particularly at plugs, convenience  
receptacles, and the point where they exit from  
the apparatus.  
6
Do not block any ventilation openings. Install in  
accordance with the manufacturer’s instructions.  
3
4
Only use attachments/accessories specified by  
the manufacturer.  
7
8
Owner Manual  
w
n
e
r
M
a
n
u
a
l
Do not install near any heat sources such as  
radiators, heat registers, stoves, or other apparatus  
(including amplifiers)that produce heat.  
Unplug this apparatus when unused for long  
periods of time.  
3
 
SAFETY INSTRUCTIONS  
Use only with the cart, stand, tripod, bracket,  
with an exact replacement part by an authorized  
servicer. Protect the power cord from physical  
or mechanical abuse, such as being twisted,  
kinked, pinched, closed in a door, or walked  
upon. Pay particular attention to plugs, wall  
outlets, and the point where the cord exits the  
appliance.  
9
or table specified by the manufacturer, or sold  
with the apparatus. When a cart is used, use  
caution when moving the cart/apparatus  
combination to avoid injury from tip-over.  
Outdoor use marking :  
Never touch this apparatus or antenna during  
a thunder or lighting storm.  
14  
15  
10  
11  
WARNING - To reduce the risk of fire or elec-  
tric shock, do not expose this appliance to rain  
or moisture.  
Do not allow a impact shock or any objects to  
fall into the product, and do not drop onto the  
screen with something.  
Refer all servicing to qualified service personnel.  
Servicing is required when the apparatus has  
been damaged in any way, such as power-supply  
cord or plug is damaged, liquid has been  
spilled or objects have fallen into the apparatus,  
the apparatus has exposed to rain or moisture,  
does not operate normally, or has been  
dropped.  
12  
Wet Location Marking : Apparatus shall not be  
exposed to dripping or splashing and no  
objects filled with liquids, such as vases, shall  
be placed on or over apparatus.  
GROUNDING  
16  
Ensure that you connect the earth ground wire  
to prevent possible electric shock. If grounding  
methods are not possible, have a qualified  
electrician install a separate circuit breaker.  
CAUTION concerning the Power Cord :  
Most appliances recommend they be placed  
upon a dedicated circuit; that is, a single outlet  
circuit which powers only that appliance and  
has no additional outlets or branch circuits.  
Check the specification page of this owner's  
manual to be certain.  
13  
Do not try to ground the unit by connecting it  
to telephone wires, lightening rods, or gas pipes.  
Power  
Supply  
Do not overload wall outlets. Overloaded wall  
outlets, loose or damaged wall outlets, extension  
cords, frayed power cords, or damaged or  
cracked wire insulation are dangerous. Any of  
these conditions could result in electric shock  
or fire. Periodically examine the cord of your  
appliance, and if its appearance indicates dam-  
age or deterioration, unplug it, discontinue use  
of the appliance, and have the cord replaced  
Short-circuit  
Breaker  
DISCONNECTING POWER:  
17  
Power is supplied to the Link-Loader if the  
power cord is connected. Unplug power cord  
from AC power outlet to remove power.  
4
 
CONTENTS  
WARNING / CAUTION  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
2
3
SAFETY INSTRUCTIONS  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
INSTALLATION MENU  
Entering the Installation Menu  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
6
Public Display Settings  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7  
TV Link-Loader  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
9
10  
11  
Password Change  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
TV Link-Loader Key Functions  
5
 
INSTALLATION MENU  
ENTERING THE INSTALLATION MENU  
The feature set up available on this LG commercial TV which features ‘TV link’ are shown on the ‘Installation  
Menu . This simple menu is designed to make it easy and efficient for the system integrator to install and set up  
the institution’s communications system.  
Public Display Mode controls operation and functionality of the TV. Once set up, these settings are clonable; they  
can be copied and transferred to another identical TV. See the TV Link-Loader section for cloning details.  
Accessing the Installation Menu with  
the Menu Button  
EZ Scan  
With an LG installer remote, press and hold down the  
Menu key for five seconds. The TV screen will show  
the Enter Password display.  
Manual Scan  
1
Channel Edit  
DTV Signal  
Input Source  
Input Label  
Set ID  
ENTER  
Key in “1-1-0-5” and press  
button. This is  
2
the initial password. The password can be changed as  
required.  
Enter Password  
Accessing the Public Display Mode Menu  
*
*
*
*
Use the D or E button to select the Public Display  
Settings option and press the G button.  
3
Installation Menu (V1.0)  
Public Display Settings  
G
TV Link-Loader  
Password Change  
Set ID setup  
G
G
G
Once in the Public Display Settings menu, use the D  
button to select and adjust the menu options  
4
E F G  
to your requirements. If you want Public Display mode  
to be enabled, select ‘Yes’ for that option.  
Accessing the Public Display Mode  
Menu with the Mode Button  
MODE  
Press and hold the  
button for more that 3  
1
seconds. The TV will automatically display the  
Installation Menu after about 5-7 seconds.  
6
 
PUBLIC DISPLAY SETUP  
Set item to act TV with standalone.  
Installation Menu (V1.0)  
Public Display Settings  
Use the D or E button to select desired menu options.  
1
G
TV Link-Loader  
Password Change  
Set ID setup  
G
G
G
Use the F or G button to adjust the menu option settings.  
2
Public Display Settings  
Public Display Mode  
Start Channel  
Ch. Type  
No  
No  
DTV  
12  
2
Major  
Public Display Mode Menu Items  
Minor  
Minimum Volume  
Maximum Volume  
Start Volume  
Level  
0
01. Public Display Mode  
100  
No  
15  
No  
7
If ‘Public Display Mode is set to Yes (Enabled), all functions of Public Display  
Settings are active. If ‘Public Display Mode is set to No (Disabled), all functions  
of Public Display mode are not active.  
Power Management  
Setting  
02. Start Channel  
Key Management  
Factory Reset  
Aspect Ratio  
0
This function allows you to determine the initial channel number when the TV  
is turned On. This feature is useful for an in-house information channel, since  
the TV would always select that channel when it is turned On. Setting this to  
255 causes the last channel viewed when the TV was turned Off, to be the  
tuned to channel when the TV is turned On again.  
0
0
03. Minimum Volume  
This function determines the minimum volume level allowable with the VOLUME  
(VOL) Up/Down control. In this way, for example, someone cannot set the vol-  
ume too low to hear. The value range is from 0 to 63 — change values with ADJ  
Left/Right arrow. The factory default is 0, which provides the full range of vol-  
ume control, if item 009 MAX VOLUME is also set to 63. It may be best to set  
the same value on every TV.  
NOTE: The minimum volume level cannot have a value setting higher than the  
MAX VOLUME level (described below).  
04. Maximum Volume  
This function determines the maximum volume level allowable with the VOL-  
UME (VOL) Up/Down controls. In this way, for example, someone can not set  
the volume level high enough to disturb others. The value range is 0 to 63, with  
63 as the default, which gives the user the full range of volume control, if item  
008 MIN VOLUME is also set at 0. Change values with ADJ Left/Right arrow  
keys. It may be best to set the same value on every TV.  
NOTE: The maximum volume level cannot have a value setting lower than the  
MIN VOLUME level (described previously).  
7
 
INSTALLATION MENU  
05. Start Volume  
08. Factory Reset  
Set to 0 for normal.  
This function allows the Installer to determine the initial volume  
level setting when the TV is turned ON. This feature is useful  
for an in-house information channel, since the TV would always  
select that Volume level when it is turned on. The range of values  
are 0 - 63, 255. If 255 is selected, the current volume level will  
be retained in memory when the TV is turned Off. At TV turn  
On, Volume level is automatically set to the previous level.  
Setting is retained in non-volatile memory.  
Set to 1 to load presets to all of the previous item settings and  
exit menu.  
WARNING: Setting this to 1 will reload the factory defaults.  
Setting is retained in non-volatile memory.  
09. Aspect Ratio  
Selects default aspect ratio at power up, see settings below.  
Set to 0 to disable. Aspect Ratio will stay at previous state.  
Set to 1 “Set By Program.  
06. Power Management  
Determines hours of no activity before automatic shutoff. The  
POWER MANAGE function is for saving energy. If set to No,  
Power Manage is disabled. Settings range from 1 ~ 7, repre-  
senting the hours that the unit will remain On, unless there has  
been activity from either the control panel or remote control.  
Setting is retained in non-volatile memory.  
Set to 2 for 4:3.  
Set to 3 for 16:9 (Factory Default).  
Setting is retained in non-volatile memory.  
Item  
Enable  
Disable  
Initial  
07. Key Management  
Public Display Mode Yes  
No  
No  
No  
No  
TV  
2
If set to 1, key defeat prevents the end user from accessing the  
on-screen menus with the display front panel-MENU, SELECT,  
and F or G button do not function. If set to 0, those keys do  
function.  
Start Channel  
Ch. Type  
Yes  
TV/CATV/DTV/CADTV  
Subject to Ch. Type  
Subject to Ch. Type  
0 ~ 100  
Major No.  
Note: The menus can always be accessed by pressing MENU  
button on the remote.  
Minor No.  
0
Minimum Volume  
Maximum Volume  
Start Volume  
Level  
0
Key management when enabled determines the level of control  
that the guest has over the television. Key management has  
four modes: (default is ‘0’)  
0 ~ 100  
100  
No  
Yes  
Yes  
No  
0 ~ 100  
No  
0 = Television is unrestricted and responds to all commands.  
1 = Key defeat ”prevents the television from responding  
to “MENU”key presses on the front panel.  
Power Management  
Setting  
No  
1
1 ~ 7  
0 ~ 3  
0 ~ 1  
0 ~ 3  
2 = “Key Lock ”prevents the television from responding to  
any front panel key press.  
Key Management  
Factory Reset  
Aspect Ratio  
0
0
3 = “System provider ”mode allows access to the menu  
system from the front panel or remote control but  
access is controlled as follows  
0
* TV Guide if equipped – no access  
* “Setup” – only access to main/pip input select screens  
* “Video” – no access  
* “Audio” – no access  
* “Time” – only access to sleep timer  
* “Option”– only access to aspect ratio, closed caption,  
SimpLink  
* “Lock” – full access  
Setting is retained in non-volatile memory.  
8
 
TV LINK-LOADER  
The TLL-1100A TV TV Link-Loader is not supplied with this TV. It is available for purchase from your LG dealer as  
an optional item. See your LG dealer.  
The TV Link-Loader allows a Master TV setup with Public Display Mode Setup to be copied and transferred into  
other identical TVs. Once copied into another identical TV, the Target TV will function exactly like the original.  
Note: Please see TLL-1100A Installation and Operating Guide for complete TV Link-Loader Setup and Cloning  
Operating Instructions.  
TV / Link-Loader Setup  
Connections  
Connect the MPI cord provided with the TLL-1100A TV Link-Loader into the TV RS-232C port. Connect the other end of the cable  
with the stereo mini-plug into the RS-232C input port which is located on the right side of the Link-Loader.  
On-Off Switch  
Just below the RS-232C input on the Link-Loader is the On-Off Switch. Set the switch to the On position. The display should read  
‘TLL-1100A Ready.  
TV Setup  
Turn the TV display panel on. Tune to an analog channel.  
TLL-1100A TV Link-Loader Operation  
Point the unit toward the lower center of the TV screen (IR receiver). While holding the unit steadily in this position, press and hold  
the Mode button in until the TV Link Loader LCD display changes from “Ready” to “Mode in. Continue to hold Mode in as the LED  
on TV blinks while the TV goes through the access sequence and shows the Setup menu, the Password Menu and finally the Installation  
menu. Release the Mode button. Use the Down arrow button to select ‘TV Link-Loader’ and press the Enter button. ‘Ready to Download’  
display will appear on the TV screen.  
Receiving Master TV Setup Data  
Press the Receive button to put the Link-Loader into Receive mode. The LCD will show Receive. Press the Enter button to begin receiving.  
The LCD will show 0XX Prg the progress bar. Check the TV Volume OSD to show receiving progress. The Link-Loader will record the  
TV setup data in its internal memory. If an error occurs, press Receive to cancel receiving.  
Sending Master TV Setup Data  
Press the Send button to put the Link-Loader into Send mode. When IR Send or RS Send appears on the LCD, press Enter. The Link-  
Loader will transfer the TV setup data in its internal memory to the Target TV. If an error occurs, press Send to cancel sending. After  
the transfer is complete, the OSD is removed from the screen and the TV turns off. TV turn off indicates that the transfer is complete.  
Refer to the TLL-1100A User’s Manual for more detailed information.  
9
 
INSTALLATION MENU  
PASSWORD CHANGE  
If security for the system is a critical issue, the password can  
be changed.  
Changing the Password  
Installation Menu (V1.0)  
Public Display Settings  
Password Change  
button.  
Use the D or Ebutton to select the  
option and then press the G or  
1
2
ENTER  
G
TV Link-Loader  
Password Change  
Set ID setup  
G
G
G
Key in 1-1-0-5 or the old password.  
I
If the password is incorrect, the unit will return to the  
Installation menu.  
New  
Key in a new four digit password, key in the password  
again for confirmation.  
*
*
*
*
*
*
*
*
Confirm  
I
Password cannot be “8-7-4-1. That sequence of  
number is used to enter the calibration menu.  
SET ID SETUP  
Installation Menu (V1.0)  
Public Display Settings  
Set ID Setup  
button.  
Use the  
option and then press the Gor  
or  
button to select the  
ENTER  
D
E
1
G
TVLink-Loader  
Password Change  
Set ID setup  
G
G
G
Select Yes to enable set ID Lock or No to disable set  
ID Lock.  
2
3
Set ID setup  
Set ID Lock  
Set ID  
No  
Key in a set ID number 1 ~ 99.  
1
10  
 
TV LINK-LOADER KEY FUNCTIONS  
(See Users Manual for Key Functions)  
TV LINK  
Loader  
Shows current operating function.  
LCD FUNCTION  
DISPLAY WINDOW  
TLL 1100A  
Ready  
Selects ‘Ready’ and ‘Mode In’ functions.  
MODE  
MODE  
MENU  
Brings up the main menu to the screen.  
Enters or exits menus and submenus.  
MENU  
Use to navigate menus and submenus.  
UP/DOWN/LEFT  
/RIGHT/ENTER  
ENTER: Functions like an Enter key on a regular  
remote control.  
Up: Channels Up.  
ENTER  
Down: Channels Down.  
Left: Controls Volume Down.  
Right: Controls Volume Up.  
RECEIVE  
SEND  
See Users Manual for send key functions.  
SEND  
Send key functions change depending on operating  
mode.  
RECEIVE See Users Manual for receive key functions.  
Receive key functions change depending on  
operating mode.  
11  
 
For Customer Support/Service Please call:  
1-888-865-3026  
Marketed and Distributed in the United States by LG Electronics U.S.A., Inc.  
1000 Sylvan Avenue  
Englewood Cliffs, NJ 07632  
©Copyright 2007, LG Electronics U.S.A., Inc.  
 

Kustom Musical Instrument Amplifier KG100HFX User Manual
LG Electronics Computer Monitor W2252TQ User Manual
Life Fitness Elliptical Trainer 95XE 0XXX 02 User Manual
Little Wonder Edger 6232 User Manual
Mackie Music Mixer CFXMKII User Manual
Magnavox CRT Television MS3252S MS3652S User Manual
Magnavox Flat Panel Television 22MF339B F7 User Manual
Makita Cordless Drill 6202D User Manual
Marantz Car Stereo System CD5005 User Manual
Microsoft Computer Accessories 5908400 User Manual