Installation Manual
Electric Range
LSC5622W / LSB5611S / LST5601S / LSC5633W
LSC5674W / LSC5683W / LSB5682S / LST5651S
LRE3091S / LSE3094S / LSE3092S
Please read these instructions thoroughly before
installing and operating the range.
P/No.: MFL55646202
Part 1
SAFETY
PREPARE TO INSTALL THE RANGE
WARNING
• The information in this manual
TOOLS NEEDED
should be followed exactly.
- A fire or electrical shock may result causing
property damage, personal injury or death.
WARNING
• DO NOT step or sit on the
door. Install the Anti-Tip
Bracket packed with range.
- The range could be tipped and
injury might result from spilled hot
liquid, food, or the range itself.
- If the range is pulled away from the
wall for cleaning, service, or any
other reason, ensure that the Anti-
Tip Device is properly reengaged
when the range is pushed back
against the wall.
Safety Glasses
Tape Measure
Gloves
Pencil
PARTS PROVIDED
CAUTION
• Put on gloves during installation
procedure.
- Failure to do so can result in bodily injury.
NOTE
• Read all instructions contained in these installation
instructions before installing range.
• Remove all packing materials from the oven
compartments before connecting the electrical
supply to the range.
Rear filler & 2 Screws
(LSE Series only)
• Observe all governing codes and ordinances.
•
Be sure to leave these instructions with the consumer.
NOTE
(For Anti-Tip Bracket Mounted
on Concrete Floors and Walls)
Keep these instructions with your owner’s manual for
future reference.
• As when using any appliance generating heat, there
are certain safety precautions you should follow.
• Be sure your range is installed and grounded
properly by a qualified installer or service technician.
• Make sure the wall coverings around the range can
withstand the heat generated by the range.
• To eliminate the need to reach over the surface
elements, cabinet storage space above the elements
should be avoided.
PARTS NOT PROVIDED
3
Part 2
PREPARE TO INSTALL THE RANGE
2 INSTALLATION DRAWINGS (LRE Series only)
NOTE
SAVE FOR THE USE OF THE LOCAL ELECTRICAL INSPECTOR.
CLEARANCES AND DIMENSIONS (Figure 1)
To install range refer to the following Figure 1.
For installation in CANADA, a Free-standing range is not to be installed closer than 12mm from any
adjacent surface.
CAUTION
CAUTION
• Make sure that the wall covering,
countertop and cabinets around the
range can withstand the heat (up to
• Cabinet storage space located above
the surface units should be avoided.
- The risk of burns or fire by reaching over
heated surface units can be eliminated.
194°F) generated by the range.
- Discoloration, delamination or melting may occur.
- This range has been designed to comply with the
maximum allowable wood cabinet temperatures
of 194°F.
• Install a range hood that projects
horizontally a minimum of 5 inches
beyond the bottom of the cabinets If
cabinet storage is to be provided.
- The risk can be reduced.
A = 30”(76.2 cm) For U.S.A
= 30”(76.2 cm) ~ 31”(78.7 cm) For CANADA
FIGURE 1
FIGURE 2
MINIMUM DIMENSIONS (FIG. 2)
* 30”(76.2cm) minimum clearance between the top of the cooking surface and the bottom of an
unprotected wood or metal cabinet; or 24”(60.9cm) minimum when bottom of wood or metal cabinet is
protected by not less than 1/4”(6.4cm) flame retardant millboard covered with not less than no. 28 MSG
sheet steel, 0.015”(0.381mm) stainless steel, 0.024”(0.610mm) aluminum or 0.020”(0.508mm) copper.
** 15”(38.1cm) minimum between countertop and adjacent cabinet bottom.
4
Part 2
PREPARE TO INSTALL THE RANGE
2 INSTALLATION DRAWINGS (LSE Series only)
NOTE
SAVE FOR THE USE OF THE LOCAL ELECTRICAL INSPECTOR.
CLEARANCES AND DIMENSIONS (Figure 1)
To install range refer to the following Figure 1.
For installation in CANADA, a Free-standing range is not to be installed closer than 12mm from any
adjacent surface.
CAUTION
CAUTION
• Make sure that the wall covering,
countertop and cabinets around the
range can withstand the heat (up to
• Cabinet storage space located above
the surface units should be avoided.
- The risk of burns or fire by reaching over
heated surface units can be eliminated.
194°F) generated by the range.
- Discoloration, delamination or melting may occur.
- This range has been designed to comply with the
maximum allowable wood cabinet temperatures
of 194°F.
• Install a range hood that projects
horizontally a minimum of 5 inches
beyond the bottom of the cabinets If
cabinet storage is to be provided.
- The risk can be reduced.
24”
(60.9cm)
A = 30”(76.2 cm) For U.S.A
= 30”(76.2 cm) ~ 31”(78.7 cm) For CANADA
FIGURE 1
FIGURE 2
MINIMUM DIMENSIONS (FIG. 2)
* 30”(76.2cm) minimum clearance between the top of the cooking surface and the bottom of an
unprotected wood or metal cabinet; or 24”(60.9cm) minimum when bottom of wood or metal cabinet is
protected by not less than 1/4”(6.4cm) flame retardant millboard covered with not less than no. 28 MSG
sheet steel, 0.015”(0.381mm) stainless steel, 0.024”(0.610mm) aluminum or 0.020”(0.508mm) copper.
** 15”(38.1cm) minimum between countertop and adjacent cabinet bottom.
5
Part 3
INSTALL THE RANGE
3 ELECTRICAL CONNECTION
REQUIREMENTS
The range must be installed in accordance with Local
and Canadian Electrical Codes (latest edition). See
rating plate for total connected Amp rating. This
model was shipped direct from the factory with
Service cord attached. There are no range
connections necessary.
Note: Cord replacement
Only a range cord rated at 40 amps with 120/240
minimum volt range is required. If a 50 amp range
cord is used, it should be marked for use with 13⁄8”
diameter connection openings.
Use a spirit level to check your adjustments. Place the
level diagonally on the oven rack, and check each
direction for level.
First check direction 1 .
After check direction 2 .
ANTI-TIP DEVICE INSTALLATION
4
WARNING
• DO NOT step or sit on the
door. Install the Anti-Tip
Bracket packed with range.
- The range could be tipped and
injury might result from spilled hot
liquid, food, or the range itself.
- If the range is pulled away from the
wall for cleaning, service, or any
other reason, ensure that the Anti-
Tip Device is properly reengaged
when the range is pushed back
against the wall.
If the spirit level doesn’t show
level on the rack, adjust the
leveling legs with a wrench.
5 FINAL INSTALLATION
• Move range close enough to the opening to plug
into the receptacle.
• Slide range into position insuring that the left back
leg slides under the anti-tip bracket. Range will sit 0”
away from the back wall when properly installed.
• Carefully tip range forward to insure that the anti-tip
bracket engages the range back brace and prevents
tip-over.
• Turn on electrical power. Check range for proper
operation as described in owner’s manual.
Optional rear filler
If the counter does not bridge the opening at the rear
wall the rear filler kit, that is provided with the slide in
range, will be needed.
1. Locate the bracket using the template
An Anti-tip bracket is packaged with template. The
instructions include necessary information to
complete the installation.
NOTE : If the countertop depth is greater than 25”
there will be a gap between the filler kit and the back
wall.
Read and follow range installation instruction sheet
(template).
2. Level the range
If the countertop depth is less than 24”, the control
panel will not sit flush with the countertop.
(See figure 1 on page 5)
Level the range by adjusting the leveling legs with a
wrench.
6
|