TM
Leica DISTO D3
The original laser distance meter
1
2
3
5
4
6
7
8
9
11
10
19
13 15
11
16,17,18
12 14
10
20
1
2
4
MENU
21
22
23
UNIT RESET
TRIPOD
BEEP ONOFF
TIMER
a
?
3
27
5
max
a
b
b
24
28
25
29
26
b
6
min
7,8,9
30
EN
F
User Manual
Safety Instructions
Symbols used
English
E
The symbols used in the Safety Instructions have the
following meanings:
Congratulations on the purchase of your
Leica DISTO™ D3 .
P
WARNING:
Indicates a potentially hazardous situation or
an unintended use which, if not avoided, will result in
death or serious injury.
Carefully read the Safety Instruc-
ƽ
tions and the User Manual before
using this product.
The person responsible for the instrument must
ensure that all users understand these directions and
adhere to them.
CAUTION:
ƽ
Indicates a potentially hazardous situation or
an unintended use which, if not avoided, may result
in minor injury and/or in appreciable material, finan-
cial and environmental damage.
Measuring ............................................................9
Functions...........................................................10
Appendix............................................................15
Important paragraphs which must be adhered
to in practice as they enabled the product to be used
in a technically correct and efficient manner.
)
Use of the instrument
Permitted use
•
•
•
Measuring distances
Computing functions, e. g. areas and volumes
Measuring tilts
Prohibited use
•
•
•
Using the instrument without instruction
Using outside the stated limits
Deactivation of safety systems and removal of
explanatory and hazard labels
Leica DISTO™ D3 760498a en
1
Safety Instructions
•
•
Opening of the equipment by using tools (screw-
drivers, etc.), as far as not specifically permitted
for certain cases
Carrying out modification or conversion of the
product
Use after misappropriation
Use of accessories from other manufacturers
without the express approval of Leica Geosys-
tems.
Deliberate or irresponsible behaviour on scaf-
folding, when using ladders, when measuring
near machines which are running, or near parts of
machines or installations which are unprotected
Aiming directly into the sun
Deliberate dazzling of third parties; also in the
dark
EN
F
Areas of responsibility
Responsibilities of the manufacturer of the orig-
inal equipment Leica Geosystems AG, CH-9435
Heerbrugg (for short Leica Geosystems):
Leica Geosystems is responsible for supplying the
product, including the User Manual and original
accessories, in a completely safe condition. (addi-
tional language versions can be found at:
E
•
•
P
•
Responsibilities of the manufacturer of non-
Leica accessories:
•
•
The manufacturers of non-Leica accessories
)
for the Leica DISTO™ are responsible for developing,
implementing and communicating safety concepts for
their products. They are also responsible for the
effectiviness of these safety concepts in combination
with the Leica Geosystems equipment.
•
Inadequate safeguards at the surveying site (e.g.
when measuring on roads, construction sites,
etc.)
Limits of use
Responsibilities of the person in charge of the
instrument:
See section “Technical Data“.
)
WARNING
The person responsible for the instrument
ƽ
The Leica DISTO™ is designed for use in areas perma-
nently habitable by humans, do not use the product
in explosion hazardous areas or in aggressive envi-
ronments.
must ensure that the equipment is used in accor-
dance with the instructions. This person is also
accountable for the deployment of personnel and for
their training and for the safety of the equipment
when in use.
The person in charge of the instrument has the
following duties:
Leica DISTO™ D3 760498a en
2
Safety Instructions
•
•
•
To understand the safety instructions on the
product and the instructions in the User Manual.
To be familiar with local safety regulations
relating to accident prevention.
WARNING:
Flat batteries must not be disposed of with
household waste. Care for the environment and take
them to the collection points provided in accordance
with national or local regulations.
EN
F
ƽ
E
To inform Leica Geosystems immediately if the
equipment becomes unsafe.
The product must not be disposed of with
household waste.
Dispose of the product appropriately in
accordance with the national regulations in
force in your country.
Always prevent access to the product by
unauthorized personnel.
P
Hazards in use
CAUTION:
ƽ
Watch out for erroneous distance measure-
ments if the instrument is defective or if it has been
dropped or has been misused or modified.
Product specific treatment and waste
management information can be downloaded from
the Leica Geosystems home page at
Precautions:
Carry out periodic test measurements. Particularly
after the instrument has been subject to abnormal
ments.
received from your Leica Geosystems dealer.
Make sure the Leica DISTO™ optics is kept clean and
Electromagnetic Compatibility
(EMC)
that there is no mechanical damage to the bumpers.
CAUTION:
ƽ
The term "electromagnetic compatibility" is taken to
mean the capability of the product to function
smoothly in an environment where electromagnetic
radiation and electrostatic discharges are present,
and without causing electromagnetic interference to
other equipment.
In using the instrument for distance measure-
ments or for positioning moving objects (e.g. cranes,
building equipment, platforms, etc.) unforeseen
events may cause erroneous measurements.
Precautions:
Only use this product as a measuring sensor, not as
a control device. Your system must be configured and
operated in such a way, that in case of an erroneous
measurement, malfunction of the device or power
failure due to installed safety measures (e.g. safety
limit switch), it is assured that no damage will occur.
WARNING:
ƽ
The Leica DISTO™ conforms to the most strin-
gent requirements of the relevant standards and
regulations. Yet, the possibility of it causing interfer-
ence in other devices cannot be totally excluded.
Leica DISTO™ D3 760498a en
3
Safety Instructions
CAUTION:
WARNING:
Changes or modifications not expressly
approved by Leica Geosystems for compliance could
void the user’s authority to operate the equipment.
EN
F
ƽ
ƽ
Never attempt to repair the product yourself. In
case of damage, contact the local dealership.
E
FCC statement (applic. in U.S.)
Laser classification
Integrated distancemeter
The Leica DISTO™ produces a visible laser beam
which emerges from the front of the instrument.
It is a Class 2 laser product in accordance with:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful inter-
ference in a residential installation.
P
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be deter-
mined by turning the equipment off and on, the user
is encouraged to try to correct the interference by
one or more of the following measures:
•
IEC60825-1 : 2007 "Radiation safety of laser
products"
Laser Class 2 products:
Do not stare into the laser beam or direct it towards
other people unnecessarily. Eye protection is
normally afforded by aversion responses including
the blink reflex.
WARNING:
ƽ
Looking directly into the beam with optical aids
(e.g. binoculars, telescopes) can be hazardous.
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help
Precautions:
Do not look directly into the beam with optical aids.
•
CAUTION:
•
•
ƽ
Looking into the laser beam may be hazardous
to the eyes.
Precautions:
Do not look into the laser beam. Make sure the laser
is aimed above or below eye level. (particularly with
fixed installations, in machines, etc.)
Leica DISTO™ D3 760498a en
4
Safety Instructions
EN
F
Labelling
Start-up
Inserting/replacing batteries
Laser Radiation
E
See figure {A}
Do not stare into the beam
Laser class 2
1
Remove battery compartment lid and attach
handstrap.
Insert batteries, observing correct polarity.
Close the battery compartment again. Replace
P
acc. IEC 60825-1:2007
Maximum radiant power:
<1mW
Emitted wavelength:
620-690nm
2
3
Beam divergence: 0.16 x 0.6 mrad
-9
Pulse duration:
1 x 10
s
the batteries when the symbol
nently in the display.
flashes perma-
Use alkaline batteries only.
)
Remove the batteries before any long period
of non-use to avoid the danger of corrosion.
)
Multifunctional endpiece
See figure {B}
Position of the product label see last page!
The instrument can be adapted for the following
measuring situations:
•
For measurements from an edge, fold out the
positioning bracket until it first locks in place. See
figure {C}.
•
For measurements from a corner, open the posi-
tioning bracket until it locks in place, then push
the positioning bracket lightly to the right to fold
it out fully. See figure {D}.
Leica DISTO™ D3 760498a en
5
Start-up
A built-in sensor automatically detects the orienta-
tion of the positioning bracket and adjusts the zero
point of the instrument accordingly.
11 Save constant value, call up constant value
12 Historical memory, call up values
13 Battery status
EN
F
14 Timer
E
15 Area/volume
16 Tilt
17 Horizontal distance measurement using tilt
18 Room corner angle function
19 Menu
20 Continuous laser
21 Reset
22 Reference (tripod)
23 Beep
24 Circumference
25 Wall area
26 Ceiling area
Keypad
P
See figure {E}:
1
2
3
4
5
6
7
8
9
ON / DIST (On/measuring) button
Plus (+) button
Minus (-) button
Area / volume button
Indirect measurement (Pythagoras) button
Reference button
Functions button
Timer button
Storage button
10 Menu/equal button
11 Clear/off button
27 Intermediate line 1
28 Intermediate line 2
29 Intermediate line 3
30 Summary line
Display
See figure {F}
1
2
3
4
5
6
7
8
9
Laser active
Reference (front)
Reference (rear)
Reference (corner stop)
Measuring with the tripod
Stake out function
Single Pythagorean measurement
Double Pythagorean measurement
Double (partial height) measurement
10 Illumination
Leica DISTO™ D3 760498a en
6
Start-up
EN
F
Setting the unit for distance mea-
Menu functions
surements
Settings
The following units can be set:
E
The menu allows settings to be altered and perma-
nently stored. After switching off the device or
replacing the batteries the settings are stored.
Distance
Area
Volume
0.000 m³
P
0.000 m²
0.000 m²
0.000 m²
0.00 ft²
0.00 ft²
0.00 ft²
0.00 ft²
0.00 ft²
0.00 ft²
0.00 ft²
0.00 ft²
1.
2.
3.
4.
5.
6.
7.
8.
0.000 m
0.0000 m
0.00 m
0.000 m³
0.000 m³
0.00 ft³
0.00 ft³
0.00 ft³
0.00 ft³
0.00 ft³
0.00 ft³
0.00 ft³
0.00 ft³
Navigation in the menu
0.00 ft
The menu allows settings to be made at the user
level. The instrument can be specifically configured to
your personal requirements.
0'00'' 1/32
0'00'' 1/16
0'00'' 1/8
0.0 in
General description
button (pressed long) brings up the
, the
9.
10.
11.
0 1/32 in
0 1/16 in
0 1/8 in
MENU
set units and the
symbol are displayed.
button (pressed short) pages through each
menu item. See figure {G}.
Setting the unit for tilt measure-
or
button (pressed short) brings up the next menu
item.
A long press on the
the new settings made in the submenu items .
Pressing the button for longer in the menu
button to make changes in menu items.
ments
The following units can be set for tilt measurements:
Units for tilt
button in the menu confirms
1.
2.
+/- 0.0°
0.00%
Beep (BEEP
)
allows you to quit the settings function without
saving.
You can switch the beep on or off.
Leica DISTO™ D3 760498a en
7
Menu functions
A reset returns the following values to their factory
settings:
EN
F
Continuous laser (
)
You can switch the continuous laser function on or
off.
•
•
•
•
•
Reference (rear)
Display illumination (ON)
Beep (ON)
Unit (m(mm))
Stack and memory are erased
E
With the continuous laser function set on, each press
P
of the
button triggers a measurement. The laser
automatically switches off after 15 minutes.
All customised settings and stored values are
also lost.
Measuring with the tripod ( TRIPOD
)
)
The reference must be appropriately adjusted in
order to be able to take correct measurements with
a tripod. To do this select the TRIPOD symbol in this
menu item. You can switch the reference on the
tripod on or off. The setting can be seen on the
Operation
Switching on and off
display
.
Switches on the instrument and laser. The
display shows the battery symbol until the
next button is pressed.
Pressing this button for longer switches the
instrument off.
The instrument switches off automatically
after 6 minutes of inactivity.
Display - keypad illumination ( )
Automatic illumination of the display and the keypad
can be switched on or off.
Reset - returning the instrument to CLEAR button
the factory settings (
)
The last action is cancelled. While making area or
volume measurements, each single measurement can
be deleted and remeasured in series.
The instrument has a RESET function. When you
select the menu function RESET and confirm, the
instrument defaults to the factory settings.
Leica DISTO™ D3 760498a en
8
Operation
EN
F
Display / keypad illumination
The instrument has a sensor that automatically
switches the display and keypad illumination on or off
in response to lighting conditions.
Measuring
Single distance measurement
E
Press to activate the laser. Press again to trigger
the distance measurement.
P
Reference setting
The result is displayed immediately.
The default reference setting is from the rear of the
instrument.
Minimum/maximum measurement
This function allows the user to measure the
minimum or maximum distance from a fixed
measuring point. It can also be used as to determine
spacings. See figure {I}
Press this button to take the next measurement
from the front edge
. A special beep sounds when-
ever the reference setting is changed.
After a measurement the reference returns automat-
ically to the default setting (rear reference). See
figure {H}.
It is commonly used to measure room diagonals
(maximum values) or horizontal distances (minimum
values).
Press this button for longer the front reference
Press and hold down this button until you hear
a beep. Then slowly sweep the laser back and forth
and up and down over the desired target point - (e.g.
into the corner of a room).
is set permanently.
Press this button, the rear reference is set again.
Press to stop continuous measurement. The
values for maximum and minimum distances are
shown in the display as well as the last measured
value in the summary line.
Leica DISTO™ D3 760498a en
9
Measuring
appears in the display.
EN
F
Functions
Press this button to take the first length
measurement (e.g. length).
Addition / subtraction
E
Distance measuring.
Press this button to take the second length
measurement (e.g. width).
The next measurement is added to the previous
one.
P
Press this button to take the third length
measurement (e.g. height). The value is shown in the
second line.
The next measurement is subtracted from the
previous one.
The volume then appears in the summary line.
This process can be repeated as required. The result
is always shown in the summary line with the
previous value in the second line.
Press the
button for longer to display additional
room information such as ceiling/floor area, surface
area of the walls, circumference.
The last step is cancelled.
Tilt measurement
Area
Press once. The
symbol appears in the
The inclination sensor measures tilts between
)
)
display.
45°.
Press this button to take the first length
measurement (e.g. length).
During tilt measurement the instrument
should be hold without a transverse tilt ( 10°).
Press this button once to activate the tilt
Press it again to take the second length
measurement (e.g. width).
sensor. The
symbol appears in the display. The
tilt is continuously shown as ° or % depending on the
setting.
The result is displayed in the summary line.
Press the
circumference.
button for longer to calculate the
Press to measure the inclination and the
distance. See figure {J}.
Volume
Press this button twice. The
symbol
Leica DISTO™ D3 760498a en
10
Functions
EN
F
Direct horizontal distance
Stake out function
Two different distances (a and b) can be entered into
the instrument and can then be used to mark off
defined measured lengths, e.g. in the construction of
wooden frames.
Press this button twice and the following
symbol appears in the display
.
E
P
Press this button to measure tilt and distance.
The summary line displays the result as the direct
horizontal distance.
See figure {L}.
Entering stake out distances:
Press this button four times and the stake out
Room corner angle function
The angles in a triangle can be calculated by
measuring the three sides. This function can be used
e. g. to check a right-angled room corner. See figure
{K}.
a
function symbol appears in the display
.
b
b
The value (a) and the corresponding intermediate line
flash.
By using
and
, you can adjust the values
Press this button three times and the room
(first a and then b) to suit the desired stake out
distances. Holding the buttons down increases the
rate of change of the values.
corner symbol appears in the display
.
Mark the reference points to the right and left (d1/
d2) of the angle to be measured.
Once the desired value (a) has been reached it can be
confirmed with the
button.
Press this button to measure the first (short)
side of the triangle (d1 or d2).
The value (b) and the intermediate line flashes (the
defined value (a) is automatically adopted). Value (b)
can be entered using
Press this button to measure the second (short)
side of the triangle (d1 or d2).
and
.
The defined value (b) is confirmed with the
button.
Press this button to measure the third (long)
side of the triangle (d3).
Pressing the
button starts the laser measure-
The result is displayed in the summary line as the
room corner angle.
ment. The display shows required stake out distance
Leica DISTO™ D3 760498a en
11
Functions
in the summary line between the stake out point
(first a and then b) and the instrument (rear refer-
ence).
positioning bracket fully folded out and the
instrument placed on a wall).
EN
F
•
The minimum/maximum function can be used -
see explanation in "Measuring -> Minimum/
maximum measurement". The minimum value
must be used for measurements at right angles to
the target; the maximum distance for all other
measurements.
If the DISTO™ is then moved slowly along the stake
out line the displayed distance decreases. The instru-
ment starts to beep at a distance of 0.1m from the
E
P
next stake out point.
a
b
b
Make sure that the first measurement and the
distance to be measured are at right angles. Use the
Minimum/maximum function, as explained in
"Measuring -> Minimum/maximum measurement".
The arrows in the display
indicate in which direc-
)
tion the DISTO™ needs to be moved in order to
achieve the defined distance (either a or b). As soon
as the stake out point is reached the beep changes
and the intermediate line starts to flash.
Indirect measurement - determining a dis-
tance using 2 auxilliary measurements
The function can be stopped at any time by pressing
the
button.
See figure {M}
e.g. for measuring building heights or widths. It is
helpful to use a tripod when measuring heights that
require the measurement of two or three measure-
ments.
Indirect measurement
The instrument can calculate distances using Pythag-
oras’ theorem.
This method is especially helpful if the distance to be
measured is difficult to reach.
Press this button once, the display shows
.
The laser is switched on.
Make sure you adhere to the prescribed
sequence of measurement:
Aim at the upper point (1) and trigger the
)
measurement. After the first measurement the value
is adopted. Keep the instrument as horizontal as
possible.
•
All target points must be in a horizontal or vertical
plane.
•
The best results are achieved when the instru-
ment is rotated about a fixed point (e.g. with the
Press and hold down this button to trigger
Leica DISTO™ D3 760498a en
12
Functions
continuous measurement, sweep the laser back and
forth and up and down over the ideal target point.
Indirect measurement - determining a chain
value using 3 measurements
EN
F
Press to stop continuous measurement (2). The
result is displayed in the summary line, the partial
results in the secondary line.
See figure {O}
E
e.g. determining the height between point 1 and
point 2 using three target points.
P
Press this button three times ; the display
Indirect Measurement - determining a dis-
tance using 3 measurements
shows the following symbol
switched on.
. The laser is
See figure {N}
Aim at the upper point (1).
Press this button twice; the display shows the
Press this button and trigger the measurement.
After the first measurement the value is adopted. The
display flashes (2).
following symbol
. The laser is switched on.
Aim at the upper point (1) and trigger the
measurement. After the first measurement the value
is adopted. Keep the instrument as horizontal as
possible
Triggers the measurement. After the second
measurement the value is adopted. The display
flashes (3).
Press and hold down this button to trigger
continuous measurement, sweep the laser back and
forth and up and down over the ideal target point.
Press and hold down this button to trigger
continuous measurement. Sweep the laser back and
forth and up and down over the ideal target point.
Press to stop continuous measurement (2). The
value is adopted. Aim at the lower point and
Press this button to end continuous measure-
ment. The result is displayed in the summary line, the
partial results in the secondary lines.
Press this button to trigger the measurement
(3). The result is displayed in the summary line, the
partial results in the secondary lines.
Leica DISTO™ D3 760498a en
13
Functions
EN
F
Storage of constants/historical
storage
Timer (self-triggering)
Press this button to set a 5-second time delay.
or
E
Storage of a constant
Press and hold down this button until the
desired time delay is reached (max. 60 seconds).
You can store and recall a frequently used value e.g.
height of a room. Measure the desired distance,
P
Once the key is released the remaining seconds until
measurement (e.g. 59, 58, 57...) are displayed in a
countdown. The last 5 seconds are counted down
with a beep. After the last beep the measurement is
taken and the value is displayed.
press and hold the
to confirm storage.
button until the device beeps
Recalling the constant
Press this button once to recall the constant
and make it available for further calculations by
The timer can be used for all measurements.
)
pressing button
.
Historical storage
Press this button twice and the previous 20
results (measurements or calculated results) are
shown in reverse order.
The
and
Press this button to use a result from the
summary line for further calculations.
Pressing the and buttons at the same time
buttons can be used for navigation.
erases all the values in historical storage.
Leica DISTO™ D3 760498a en
14
Functions
Error
Cause
Remedy
EN
F
Appendix
Error Hardware error
Switch on/off the
device several times. If
the symbol still
Message codes
E
appears, then your
instrument is defective.
Please call your dealer
for assistance.
All message codes are displayed with either
"Error". The following errors can be corrected:
or
P
Cause
Remedy
Technical data
156
160
Transverse tilt
Hold the instrument
without any transverse
tilt
greater than 10°
Distance
measurements:
Measuring accuracy
up to 30 m
typically:
1.5 mm*
1/16 ’’*
Main tilt direction,
angle too high
(> 45°)
Measure angle up to
max. 45°
(2 σ, standard deviation)
204
252
Calculation error
Repeat procedure
Power Range
Temperature too
Cool down instrument
Technology™:
0.05 m to 100 m
high
Range (use target plate
from about 80m)
253
255
Temperature too
low
Warm up instrument
Smallest unit displayed
Distance measurement
Minimum/maximum
measurement, Continuous
measurement
0.1 mm
Receiver signal too Use target plate
9
weak, measurement
time too long,
9
distance > 100 m
256
257
Received signal too Target too reflective
Area/volume calculation of
strong
(use target plate)
9
9
9
room data
Wrong measure-
Darkentarget(measure
Addition / subtraction
ment, background
in different lighting
brightness too high conditions)
Indirect measurement
260
Laser beam inter-
Repeat measurement
using Pythagoras
rupted
Leica DISTO™ D3 760498a en
15
Appendix
Tilt measurements:
Tilt sensor:
Dimensions
Weight (with batteries)
125 x 45 x 25 mm
110 g
EN
F
Accuracy
Temperature range:
(2 σ, standard deviation)
Storage
-25°C up to +70°C
(13°F up to +158°F)
-10°C up to +50°C
(14°F up to +122°F)
- to laser beam
- to the housing
0.3°
0.3°
E
Operation
Indirect measurement
using tilt sensor (direct
horizontal distance)
P
9
9
* maximum deviation occurs under unfavourable conditions such
as bright sunlight or when measuring to poorly reflecting or very
rough surfaces. Measuring accuracy may deteriorate by approx.
0.1 mm/m for distances above 30 m.
Angle measurement using
tilt sensor( 45°)
General:
Laser class
II
Measuring conditions
Laser type
635 nm, < 1 mW
Ø laser point
6 / 30 / 60 mm
Measuring range
(at distances)
(10 / 50 / 100 m)
The range is limited to 100 m.
Autom. laser switch-off
after 3 min
At night or dusk and if the target is in shadow the
measuring range without target plate is increased.
Use a target plate to increase the measurement
range during daylight or if the target has poor reflec-
tion properties.
Autom. instrument switch-
after 6 min
off
Display illumination
Keypad illumination
Multifunctional endpiece
Timer (self-triggering)
Save constant value
9
9
9
9
9
Target surfaces
Historical storage
Measuring errors can occur when measuring toward
colourless liquids (e.g. water) or dust free glass,
Styrofoam or similar semi-permeable surfaces.
9
(20 values)
Tripod thread
9
Battery life,
up to
Type AAA, 2 x 1.5V
5 000 measurements
Aiming at high gloss surfaces may deflect the laser
beam and lead to measurement errors.
Protection against
IP 54, dust-proof,
splashes and dust
splash-proof
Leica DISTO™ D3 760498a en
16
Appendix
Against non-reflective and dark surfaces the
measuring time may increase.
EN
F
Care
E
Do not immerse the instrument in water. Wipe off dirt
with a damp, soft cloth. Do not use aggressive
cleaning agents or solutions. Handle the instrument
as you would a telescope or camera.
P
Warranty
The Leica DISTO™ D3 comes with a three* year
warranty from Leica Geosystems AG.
More detailed information can be found at:
All illustrations, descriptions and technical specifica-
tions may be subject to change without prior notice.
* To receive the three year warranty, the product must be regis-
purchase date. If the product is not registered, a two year
warranty applies.
Leica DISTO™ D3 760498a en
17
Appendix
1
7
2
EXIT
6
3
1
2
3
4
5
max.
Leica DISTO™ D3
Leica Geosystems AG, Heerbrugg, Switzerland has been certified as being equipped
with a quality system which meets the International Standards of Quality
Management and Quality Systems (ISO standard 9001) and Environmental
Management Systems (ISO standard 14001).
Total Quality Management - Our commitment to total customer satisfaction. Ask
your local Leica Geosystems agent for more information about our TQM program.
Printed in Switzerland - Copyright Leica Geosystems AG, Heerbrugg,
Switzerland 2007
Translation of original text (760150)
Pat. No.: WO 9427164, WO 9818019, WO 0244754, WO 0216964,
US 5949531, EP 1195617, US 7030969, WO 03104748
Leica Geosystems AG
CH-9435 Heerbrugg
(Switzerland)
|