MODEL DVD-1002
PROGRESSIVE SCAN PLAY
•
(FOR TVS WITH APPROPRIATE INPUT JACKS)
PLAYS DVD VIDEOS
•
•
•
•
•
PLAYS ALL AUDIO CDS
PLAYS MP3 RECORDED DISCS
PLAYS CD-R & CD-RW DISCS
PLAYS JPEG PHOTO DISCS
PLEASE READ CAREFULLY BEFORE USE
IB-DVD1002 (AT)-WM-E-032706
IB-DVD1002(AT)-WM-E-032706.pmd
1
7/5/2006, 10:24 AM
SAFETY INSTRUCTIONS
Do not apply oil or petroleum products or solvents to any part of this set.
FCC NOTE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept
any interference received, including interference that may cause undesirable operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect this equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE
This product incorporates copyright protection technology that is protected by method claims of
U.S. patent numbers 4,631,603; 4,819,098; 4,907,093; 5,315,448; and 6,516,132 and other
intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this
copyright protection technology must be authorized by Macrovision Corporation, and is intended
for home and other limited viewing uses only, unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
CAUTION
INCLUDED ACCESSORIES
Use of controls or adjustments or
performance of procedures other than
those specified herein may result in
hazardous radiation exposure. Do not
open covers and do not repair yourself.
Refer servicing to qualified personnel.
This DVD VIDEO player is classified as
CLASS 1 LASER PRODUCT as stated on
the bottom of the set.
The following items are included with your
DVD player:
- Remote Control
- AAA Batteries (2)
- Audio/Video Cables
- User’s Guide
- Product Registration Card
IB-DVD1002 (AT)-WM-E-032706
2
IB-DVD1002(AT)-WM-E-032706.pmd
3
7/5/2006, 10:24 AM
TABLE OF CONTENTS
• Getting Started:
Safety Instructions ----------------------------------------------------------------------------------------1
Connections ------------------------------------------------------------------------------------------------4
Location of Controls --------------------------------------------------------------------------------------6
Remote Control Operation -----------------------------------------------------------------------------8
Notes on Discs ---------------------------------------------------------------------------------------------9
Precautions -------------------------------------------------------------------------------------------------10
• Initial Setting:
System Setup (TV System, Sleep Control, TV Type & Default)
Setting the TV System -----------------------------------------------------------------------------11
Setting the Sleep Control ------------------------------------------------------------------------11
Selecting the TV Type -----------------------------------------------------------------------------12
Default - Resetting the Functions to Factory Defaults -------------------------------------12
Language Setup (OSD, Audio, Subtitle & Menu) ------------------------------------------------13
Audio Setup
Setting the Digital Audio out --------------------------------------------------------------------13
Setting the Downmix Audio out ----------------------------------------------------------------14
Video Setup ------------------------------------------------------------------------------------------------14
• Basic Operation:
1. Basic Play --------------------------------------------------------------------------------------------15
2. Using the Search & Skip Functions ----------------------------------------------------16
3. Repeat Play ------------------------------------------------------------------------------------------16
4. Programmed Play --------------------------------------------------------------------------------17
5. Search for Preferred Play ---------------------------------------------------------------------18
6. Zoom Play ------------------------------------------------------------------------------------------18
7. Slow-Motion Play ---------------------------------------------------------------------------------19
8. Viewing from a Desired Angle ---------------------------------------------------------------19
9. Selecting Audio Mode --------------------------------------------------------------------------19
10. Change Subtitle Language -------------------------------------------------------------------19
11. Displaying Disc Information -------------------------------------------------------------------20
12. MP3 Disc Operation -----------------------------------------------------------------------------21
13. JPEG or Picture Disc Operation --------------------------------------------------------------21
• Trouble Shooting -----------------------------------------------------------------------------------------22
• Glossary ---------------------------------------------------------------------------------------------------24
• Specifications --------------------------------------------------------------------------------------------25
IB-DVD1002 (AT)-WM-E-032706
3
IB-DVD1002(AT)-WM-E-032706.pmd
4
7/5/2006, 10:24 AM
(TV set)
CONNECTIONS
Connect your player to TV using one of the 3 diagrams below.
Better – S-Video
Good – Composite (Normal)
YOUR TV SET
YOUR TV SET
RED
WHITE
YELLOW
WHITE
RED
WHITE
RED
YELLOW
RED WHITE
YOUR DVD PLAYER
Cr/Pr
Cb/Pb
Y
S-VIDEO VIDEO OUT COAXIAL R - AUDIO -
L
YOUR DVD PLAYER
R - AUDIO - L
S-VIDEO VIDEO OUT COAXIAL
Cr/Pr
Cb/Pb
Y
For better picture quality, connect the DVD player
to your TV with an optional S-Video cable (not
included) and the supplied audio (red & white)
cables to your TV if your TV has an S-Video
input as above. In this connection, please set the
video output mode to S-VIDEO (see page 14).
Connect the DVD player to your TV with the
supplied video (yellow) and audio (red &
white) cables as above. In this connection,
please set the video output mode to S-VIDEO
(see page 14).
Best – Component
Y or Cb/Cr/Y) as shown. In this connection, please set
the video output mode to YUV (see page 14).
YOUR TV SET
COMPONENT VIDEO IN
Cr/Pr
Cb/Pb
Y
IMPORTANT
The progressive scan video quality is available only when
using component video inputs Pb/Pr/Y and a progressive
scan TV. Compared to interlaced video, progressive scan
video effectively doubles the scanning rate of the picture
and offers higher picture resolution and quality, resulting in a
very stable, flicker-free image. You can enter the Progressive
Scan Video mode with the following steps:
YOUR DVD PLAYER
1. Set the Video Output mode to YUV (see page 14).
2. Fully stop your DVD player.
R
- AUDIO
-
L
S-VIDEO VIDEO OUT COAXIAL
Cr/Pr
Cb/Pb
Y
3. Open the disc door.
4. Press the DISPLAY/P-SCAN button, the display will
show the tip of “ENABLE PROGRESSIVE”, use the
button to highlight “OK” option and press the OK button
to confirm.
Connect the DVD player to your
TV with the optional Component
video cables (not included) and
the supplied audio cables (red &
white) to your TV if your TV has
component video inputs (Pb/Pr/
NOTE: If you want to use Normal video or S-video
mode again, please open the disc door and press the
DISPLAY/P-SCAN button to get out of the Progressive
Scan Video mode and view in normal video mode. (If this
is not done, there will be no picture or a distorted picture.)
IB-DVD1002 (AT)-WM-E-032706
4
IB-DVD1002(AT)-WM-E-032706.pmd
5
7/5/2006, 10:24 AM
(Home Theater System)
CONNECTIONS
For theater quality sound, connect the audio cables directly to your home theater system for
maximum audio enjoyment.
Best
Better
YOUR TV SET
YOUR TV SET
YOUR DVD PLAYER
YOUR DVD PLAYER
Cr/Pr
Cb/Pb
Y
S-VIDEO VIDEO OUT COAXIAL
R
- AUDIO
-
L
R
- AUDIO
-
L
Cr/Pr
Cb/Pb
Y
S-VIDEO VIDEO OUT COAXIAL
HOME THEATER SYSTEM
WITH 5.1 CHANNEL INPUT
HOME THEATER SYSTEM
WITH 5.1 CHANNEL INPUT
For better sound, connect the DVD player to
your home theater system with the supplied
audio cables; For picture, connect the DVD
player to your TV with the supplied video cable.
In this connection, you can hear the amplified
sound through your home theater system.
For best sound, connect the DVD player to your
home theater system with a coaxial cable (not
included); For picture, connect the DVD player
to your TV with the supplied video cable.
In this connection, you can enjoy the dynamic
and realistic sound of Dolby Digital Surround
through your home theater system.
NOTE
This player is equipped with copy protection technology. Do not connect this player to your TV
via a VCR using AV cables, as the picture from this player will not appear properly on your TV.
(This player may also not be compatible with some combination TV/VCRs for the same reason.
Refer to your TV’s manufacturer for more information.)
IB-DVD1002 (AT)-WM-E-032706
5
IB-DVD1002(AT)-WM-E-032706.pmd
6
7/5/2006, 10:24 AM
LOCATION OF CONTROLS
TOP PANEL
PREVIOUS
NEXT
7
6
STOP
5
4
PLAY
PAUSE
ON
STANDBY
3
2
1
1. OPEN button - Press to open the door.
2. DISC DOOR - Open and put the DVD disc inside with label side up.
3. ON/STANDBY button - Press to switch the set on or switch to standby (off).
4. PLAY/PAUSE button - Press to start playing a disc or to pause play.
5. STOP button - Stops playing the DISC, press this twice for full stop.
6. NEXT SKIP button - Skips to the next chapter (forwards).
7. PREVIOUS SKIP button - Skips to the previous chapter (backwards).
FRONT PANEL
1
2
3
4
1. POWER indicator - The indicator lights up when the player is on.
2. STANDBY indicator -The indicator lights up when the player is in standby mode (off).
3. PLAY indicator - The indicator lights up when the disc starts playing.
4. REMOTE CONTROL SIGNAL sensor - Receives the signal from the REMOTE CONTROL
(Aim the REMOTE towards this sensor).
IB-DVD1002 (AT)-WM-E-032706
6
IB-DVD1002(AT)-WM-E-032706.pmd
7
7/5/2006, 10:24 AM
LOCATION OF CONTROLS
1. MUTE button - Instantly turns off the sound,
press again to restore sound.
2. MENU button - Press to display the disc’s menu
(if your disc has a menu).
3. TITLE button - Displays the title menu if
present in the disc.
REMOTE CONTROL
ON/STANDBY
MUTE
11
12
1
2
3
TITLE
MENU
SETUP
STOP
4.
/
button - Press to skip to previous
title, chapter or track / press and hold more than
1 second to fast backward playback.
DISPLAY
P-SCAN
4
5
13
14
5.
/
button - Press to skip to next title,
chapter or track / press and hold more than 1
second to fast forward playback.
6. DIRECTION buttons - Used in DVD menus &
audio MP3 track selection.
7. OK button - Press to start/pause play or enter a
command or confirm a selection.
6
7
PLAY/PAUSE
SUBTITLE
AUDIO
15
16
17
8
SEARCH
REPEAT
8 . NUMERIC buttons - Used in DVD menus
PROGRAM
ANGLE
ZOOM
SLOW
18
19
& audio CD/MP3 track selection.
9
9. ANGLE / PROGRAM button - In DVD mode,
press to display angle menu (if present on the
DVD disc); In STOP mode, press to program
your favorite track in CD/MP3 mode.
10
VOLUME
10. VOLUME buttons - Press to adjust the volume
level (remember to adjust your TV’s volume).
11. ON/STANDBY button - Press to turn the set ON or STANDBY.
12. SETUP button - In STOP mode, press to display the DVD player’s setup menu.
13. DISPLAY/P-SCAN button - Press this button to view the elapsed time, title or chapter
information and the track numbers during play; Press to set Progressive Scan function. (This
only works when disc door is in the open mode.)
14. STOP button - Stops play, press twice to full stop.
15. SUBTITLE button - Press to setup the subtitle (if available on your disc).
16. AUDIO button - Press to select the desired audio channel.
17. SEARCH button - Allows you to select the desired disc starting time, track or title or
select the point in time to start playback.
18. REPEAT button - Press this button to repeat the current track, chapter, title, a chosen
section (A to B), or all of the disc.
19. SLOW/ZOOM button - Press to zoom the playing picture in DVD mode or hold more than 1
second to view slow motion playback.
IB-DVD1002 (AT)-WM-E-032706
7
IB-DVD1002(AT)-WM-E-032706.pmd
8
7/5/2006, 10:24 AM
REMOTE CONTROL OPERATION
Battery Installation
Tips on Battery Use
Reversing polarities will damage the
•
batteries and possibly your REMOTE. Be
sure to follow polarity ( + and –) as indicated.
1. Push door tab
to open the battery door.
Do not mix different types batteries together
•
(Alkaline, Carbon-Zinc, Nickel-Cadmium
etc.), or old batteries with new ones.
When not in use for an extended period of
•
time (over 60 days) remove the batteries to
prevent possible acid leakage or corrosion
resulting in damage to your remote.
When the batteries have become discharged,
•
they must be disposed of in a safe manner
that complies with all applicable laws.
Installation of batteries should only be done
•
by an adult (for safety).
Remote Control Operation Range
2. Insert 2 size “AAA” alkaline batteries
(included) into the battery compartment
according to the + and – markings
inside the battery compartment.
Point the REMOTE CONTROL unit from less
than 20 feet from the remote control sensor
and within about 600 of the front of the DVD
player (not your TV set).
REMOTE SENSOR RANGE
30o 30o
Distance
within 20 feet
Remember to point the
3. Push here to close the battery door.
REMOTE CONTROL
in the direction of the
DVD player, not the TV
set.
ON/STANDBY
MUTE
TITLE
MENU
SETUP
STOP
DISPLAY
P-SCAN
PLAY/PAUSE
SUBTITLE
AUDIO
SEARCH
REPEAT
PROGRAM
ANGLE
ZOOM
SLOW
VOLUME
Tips on Remote Control Operation
The operating distance may vary according
•
to the brightness of the room.
Do not point bright lights at the remote
•
control sensor (like laser pointers).
Do not place objects between the remote
•
control unit and the remote control sensor.
IB-DVD1002 (AT)-WM-E-032706
8
IB-DVD1002(AT)-WM-E-032706.pmd
9
7/5/2006, 10:24 AM
NOTES ON DISCS
Discs that can be played
DISC TYPE & LOGO MARK
RECORDED CONTENT
DVD Video
(Region 1)
Video + Audio
DVD-R
Video + Audio
Video only
JPEG disc
“.JPG” or “JPEG”
or Audio / Video
Audio only
Music CD
Audio only
CD-R disc
or Audio / Video
Audio only
CD-RW disc
or Audio / Video
MP3 disc
Audio only
MP-3
NOTE: A hand symbol “
” may appear on the TV screen when pressing some buttons. A “
”
means that the operation is not permitted by the DVD player of the disc in that mode or at
that time, sometimes the set needs to be in stop mode or other mode for that button to
work.
Discs that cannot be played
CD-Is, CD-ROMs (including computer software discs and game discs), Data part of CD-Extras,
DVD-ROMs, DVD Audio discs, DIVX, MPEG 4 DVD discs, HD layer on SACDs or discs recorded
in another format such as SECAM, and regions other than your region. This set will also not play
damaged, scratched or dirty discs.
IB-DVD1002 (AT)-WM-E-032706
9
IB-DVD1002(AT)-WM-E-032706.pmd
10
7/5/2006, 10:24 AM
PRECAUTIONS
Safety
Operation
As the laser beam used in the DVD player
•
If the player is brought directly from a cold
•
may be harmful to the eyes, do not attempt
to disassemble the cabinet. Refer servicing
to qualified personnel only (it is perfectly
safe if you don’t unscrew and open the
cabinet).
to a warm location, or is placed in a very
damp room, moisture may condense on the
lens inside. Should this occur, the player
may not operate properly. In this case,
remove the disc and wait about an hour for
the moisture to evaporate. If the player has
not been used for a long time, turn the set
to ON to warm it up for a few minutes before
inserting a disc.
Should any solid object or liquid fall into
•
the player, unplug the player, and have it
checked by qualified personnel before
operating it any further.
This DVD player is designed to be played
•
Placement of Your DVD Player
on a stable non vibrating position. If you bump
the set during DVD play, the picture or music
may stop or skip for several seconds. This
is normal for this type of player.
Do not leave the player in a location near a
•
heat source, or in a place subject to direct
sunlight, excessive dust or mechanical
shock.
Handling Discs
Do not place the player on an inclined or
•
Do not touch the playback side of the disc.
•
unstable place.
Every fingerprint can cause playback
problems. Do not scratch the disk.
Do not place anything within 1 inch of the
•
sides or back of the cabinet. The ventilation
holes must not be covered for the player
to operate properly and prolong the life of
its components.
Do not store the Discs in a place subject
•
to direct sunlight or near heat sources.
Cleaning Discs
Don’t place this DVD player on lacquered
•
Before playing, make sure the disc is
•
finished furniture without a wood or glass
protector.
clean. If not, clean the DISC with a cleaning
cloth. Wipe the DISC in a straight motion
from the center out.
If the player or discs will be left in a car
•
parked in the sun, put the player in the trunk
or where the player will not be subjected
to the direct rays and heat of the sun.
Cleaning the Cabinet
Clean the cabinet, panel and controls with
•
a soft cloth slightly moistened with a very
mild detergent solution or a plain damp
cloth. Do not use any type of abrasive pad,
scouring powder, or solvent, such as
alcohol or benzine.
Do not use solvents such as benzine,
•
thinner, commercially available cleaners or
anti-static spray intended for vinyl LPs.
IB-DVD1002 (AT)-WM-E-032706
10
IB-DVD1002(AT)-WM-E-032706.pmd
11
7/5/2006, 10:24 AM
INITIAL SETTING
For the first time use, you may need to set some of the settings and adjustments according to your
TV and favorite preferences, but most people will not adjust the following functions and
will go directly to Page 15 for basic play.
You can adjust the SYSTEM SETUP, LANGUAGE SETUP, AUDIO SETUP and VIDEO SETUP in
the menu by following the steps below.
1 In STOP mode, press the SETUP button on the
SYSTEM SETUP
TV SYSTEM
TV TYPE
SLEEP CONTROL
DEFAULT
remote control, a SETUP menu like this will appear
NTSC
on the TV screen.
4:3 PS
B
OFF
RESTORE
A
2 Use these
/
/
/
buttons to highlight your
selection.
EXIT SETUP
3 Press the OK button to confirm your selection.
THEN OK
TO SET PRESS
TO QUIT PRESS
SETUP
4 When the setting has been finished, press the
SETUP button to exit the SETUP mode.
SYSTEM SETUP (TV SYSTEM, SLEEP CONTROL, TV TYPE & DEFAULT)
Setting the TV SYSTEM
1 In STOP mode, press the SETUP button on the
SYSTEM SETUP
remote control, “
” (System Setup) is selected.
TV SYSTEM
TV TYPE
SLEEP CONTROL
DEFAULT
NTSC
PAL
AUTO
2 Press
button to highlight “TV SYSTEM”.
B
A
3 Press button and use
/
buttons to highlight
EXIT SETUP
your preferred option.
4 Press the OK button to confirm.
THEN OK
TO SET PRESS
TO QUIT PRESS
5 Press the SETUP button to exit the SETUP mode.
SETUP
- NTSC
A USA video standard. If your TV is NTSC system, select this mode.
- PAL
A video standard in Europe. If the connected TV is PAL system, select this mode.
- AUTO
If the connected TV is multi-system, select this mode. The output format will be in accordance
with the video signal of the disc.
Setting the SLEEP CONTROL
This allows you to fall asleep to a movie or music disc and the DVD player will stop itself at a
set time.
1 In STOP mode, press the SETUP button on the
SYSTEM SETUP
remote control, “
” (System Setup) is selected.
TV SYSTEM
TV TYPE
SLEEP CONTROL
DEFAULT
120 MIN
90 MIN
60 MIN
45 MIN
30 MIN
15 MIN
2 Press
button and use
button to highlight
B
A
“SLEEP CONTROL”.
EXIT SETUP
3 Press button and use
/
buttons to highlight
your preferred option.
OFF
THEN OK
TO SET PRESS
TO QUIT PRESS
4 Press the OK button to confirm.
SETUP
5 Press the SETUP button to exit the SETUP mode.
NOTE: When the selected sleep time is reached after play, the system will go into STANDBY
mode.
IB-DVD1002 (AT)-WM-E-032706
11
IB-DVD1002(AT)-WM-E-032706.pmd
12
7/5/2006, 10:24 AM
INITIAL SETTING
Selecting the TV TYPE
Select the aspect ratio of the movie to match your TV set. There are three types of screen
sizes you may select. (NOTE: If your DISC is not encoded to allow you to change the aspect
ratio, the TV display cannot be changed.)
1 In STOP mode, press the SETUP button on the
remote control, “
” (System Setup) is selected.
SYSTEM SETUP
TV SYSTEM
2 Press
button and use
button to highlight
4:3 PS
4:3 LB
16:9
TV TYPE
SLEEP CONTROL
“TV TYPE”.
B
A
DEFAULT
3 Press button and use
/
buttons to highlight
EXIT SETUP
your preferred option.
4 Press the OK button to confirm.
THEN OK
TO SET PRESS
TO QUIT PRESS
SETUP
5 Press the SETUP button to exit the SETUP mode.
4 X 3 Standard (4:3 PS) - Choose this setting if you want to see
movies to fill the entire screen of your TV. This might mean that
parts of the picture (the left and right edges) won’t be seen.
Most discs produced in a WIDESCREEN format can’t be cropped
in this fashion.
4X3 Standard
4X3 Letterbox
4 X 3 Letterbox (4:3 LB) - Choose this setting if you want to see
movies in their original aspect ratio (width-to-height ratio). You’ll
see the entire frame of the movie, but it will take up a smaller
portion of the screen vertically. The movie will appear with black
bars at the top and bottom of the screen, but you will see everything
to the right & left of the center as in a movie theater.
16 X 9 Widescreen (16:9) - Choose this setting if your DVD Player
is connected to a WIDESCREEN TV. If you choose this setting and
you don’t have a widescreen TV, the images on the screen may
appear distorted due to vertical compression (faces may seem
long and thin or wider than normal).
If you play a disc recorded in 4 X 3 format on a widescreen TV, the
left and right side of the screen will appear black. Press STOP and
SETUP buttons to change to 4:3 ratio or match the type of TV you have.
16X9 Widescreen
Default - Resetting the functions to factory defaults
In case you fiddled around with your set’s controls and you cannot return the set to its normal
operation; we have made re-setting the major options on this set very easy for you.
1 In STOP mode, press the SETUP button on the
SYSTEM SETUP
TV SYSTEM
TV TYPE
remote control, “
” (System Setup) is selected.
2 Press
button and use
button to highlight
SLEEP CONTROL
DEFAULT
B
A
RESTORE
THEN OK
“DEFAULT”.
EXIT SETUP
3 Press
button to select “RESTORE”.
4 Press the OK button to confirm.
TO SET PRESS
TO QUIT PRESS
5 Press the SETUP button to exit the SETUP mode.
SETUP
NOTE: If you set “DEFAULT”, all items in the setup menu will be reset to default setting.
IB-DVD1002 (AT)-WM-E-032706
12
IB-DVD1002(AT)-WM-E-032706.pmd
13
7/5/2006, 10:24 AM
INITIAL SETTING
LANGUAGE SETUP (On Screen Display, AUDIO, SUBTITLE & MENU)
These items allow you to preset the OSD language (OSD = On Screen Display), audio language,
subtitle language, and menu language that will always be used for every disc (the language selected
is available).
1 In STOP mode, press the SETUP button on the
remote control, “
” (System Setup) is selected.
LANGUAGE SETUP
OSD LANGUAGE
B
ENGLISH
SPANISH
FRENCH
A
2 Use button to highlight “
3 Press button and use
” (Language Setup).
AUDIO LANG
SUBTITLE LANG
MENU LANG
B
/
buttons to highlight
A
the item which you want to change.
EXIT SETUP
4 Press
button and use
/
buttons to select
your preferred language.
THEN OK
TO SET PRESS
TO QUIT PRESS
SETUP
5 Press the OK button to confirm.
6 Press the SETUP button to exit the SETUP mode.
NOTE 1: If the language selected is not available on the disc, the original language designated
by each disc will be selected.
NOTE 2: You can change the AUDIO or SUBTITLE language easily by pressing the AUDIO or
SUBTITLE button on the remote control (refer to page 19).
AUDIO SETUP
Setting the Digital Audio Out (Only for use in COAXIAL connection mode)
Your DVD player can be connected to a home cinema system with coaxial digital audio jack to
realize high quality sound effects, digital audio output allows you to select RAW or PCM digital
signal.
1 In STOP mode, press the SETUP button on the
remote control, “
” (System Setup) is selected.
AUDIO SETUP
DIGITAL OUT
DOWNMIX
RAW
PCM
2 Use button to highlight “
” (Audio Setup).
B
A
3 Press
4 Press
button to highlight “DIGITAL OUT”.
EXIT SETUP
button and use
/
buttons to select
“RAW” or “PCM”.
THEN OK
TO SET PRESS
TO QUIT PRESS
5 Press the OK button to confirm.
SETUP
6 Press the SETUP button to exit the SETUP mode.
- RAW
The coaxial output on the rear panel is connected with a receiver that accepts Dolby
Digital, MPEG or other signals. It works for most of the coaxial connections.
- PCM
The coaxial output on the rear panel is connected with a receiver that accepts PCM SIGNALS.
IB-DVD1002 (AT)-WM-E-032706
13
IB-DVD1002(AT)-WM-E-032706.pmd
14
7/5/2006, 10:24 AM
INITIAL SETTING
Setting the Downmix Audio Out
Downmix audio output setup allows you to select LT/RT or STEREO audio output mode.
1 In STOP mode, press the SETUP button on the
remote control, “
” (System Setup) is selected.
AUDIO SETUP
DIGITAL OUT
2 Use button to highlight “
” (Audio Setup).
DOWNMIX
LT/RT
3 Press
button and use
button to highlight
B
STEREO
A
“DOWNMIX”.
EXIT SETUP
4 Press
button and use
/
buttons to select
“LT/RT” or “STEREO”.
THEN OK
TO SET PRESS
TO QUIT PRESS
SETUP
5 Press the OK button to confirm.
6 Press the SETUP button to exit the SETUP mode.
- LT/RT
Select this item when the disc supporting Pro Logic Dolby Stereo is played. You have the
opportunity to hear a program’s soundtrack in the most accurate and realistic presentation
possible.
- STEREO
For 5-channel output, the left and right track signals are output simultaneously; For 2-channel
output, the ordinary stereo signal is output.
VIDEO SETUP (VIDEO OUT)
If the video connection is Normal or S-Video, please set the Video Output to S-VIDEO; If you
want to use the Component Video connection or Progressive Scan video (see page 4), please
set the Video Output to YUV mode.
1 In STOP mode, press the SETUP button on the
remote control, “
” (System Setup) is selected.
VIDEO SETUP
VIDEO OUT
YUV
2 Use
button to highlight “
button to highlight “VIDEO OUT”.
button and use buttons to select
” (Video Setup).
S-VIDEO
B
3 Press
4 Press
A
EXIT SETUP
/
“YUV” or “S-VIDEO”.
THEN OK
TO SET PRESS
TO QUIT PRESS
5 Press the OK button to confirm.
SETUP
6 Press the SETUP button to exit the SETUP mode.
NOTE 1: YUV is a superior video standard. It can optimize the translation of the Video, Y
means Luminance, U and V mean chrominance.
NOTE 2: If sound does not come out of your TV, try using other AUDIO INPUT jacks near the
Video jacks and make sure jacks are plugged in.
IB-DVD1002 (AT)-WM-E-032706
14
IB-DVD1002(AT)-WM-E-032706.pmd
15
7/5/2006, 10:24 AM
1. BASIC PLAY
1 After completing all of the audio and video cable connections, turn on your TV and set it to the
correct video-in channel (for more information, please see box below).
2 Plug the player’s AC power cord into an AC wall outlet and press ON/STANDBY button on
the player or on the remote control.
3 Press the OPEN button on the DVD player to open the disc
door. Place a disc gently on the tray (lable side up) and close the
door by pushing it down. The DVD player starts to read the disc’s
table of contents (this may take 10-20 seconds).
NOTE 1: Load the disc with the label side facing up, when
playing a double-sided disc, load it with the desired
playing side face down.
PUSH HERE
NOTE 2: “NO DISC” or “ERR DISC” will show in the display if
Disc
the disc is upside down or the disc is badly scratched
or dirty, it will not play, please clean it or change the
LABEL SIDE UP
disc, also you can buy a disc polisher to repair it.
4 Press VOLUME + or VOLUME – button to adjust the volume level on your TV’s REMOTE
and DVD’s REMOTE.
5 Some discs will start playing automatically, and others will display the Disc Contents Menu
on TV screen. If the menu is presented, use the
,
,
&
buttons to highlight your selection
and press OK button to confirm. To select a play option, press numeric buttons (0-9).
6 To pause playback, press the
button; To stop playback, press the STOP button.
NOTE: During play, press the STOP button once, the display will show “PRE STOP
”, if
you press the STOP button the second time, the display will show “STOP ”, and
now your system is in the full STOP mode.
7 To resume playback, press the
button.
8 To skip to another track/chapter, press the
/
buttons repeatedly during playback.
9 To access the disc menu or title menu during DVD play, press the MENU or TITLE button
on the remote control.
NOTE: This player has a screen saver which will display a bouncing DVD oval if the player is
stopped or paused and no button is pressed for a while.
How to Find your TV’s Video Input Channel
Make sure you have completed all the connections (see pages 4-5), you may need to
change your TV’s video input mode to see the DVD player’s menu and movies. The video
input channel varies with different brands and models, many TV remote controls have a
TV/VIDEO button which can be used to change to different video inputs and back to TV for
normal broadcast viewing. Once you selected the correct channel, your TV will show the
opening DVD screen. For more details, please see your TV manual.
IB-DVD1002 (AT)-WM-E-032706
15
IB-DVD1002(AT)-WM-E-032706.pmd
16
7/5/2006, 10:24 AM
2. USING THE SEARCH & SKIP FUNCTIONS
During play, you can search quickly through a chapter or track or use the skip function to jump
to the next selection.
Search through a Chapter or a track
1 During play, press and hold the FORWARD
button on the REMOTE CONTROL to search
forward at a faster speed, the fast search speed changes as follows:
FORWARD X2
PLAY
FORWARD X4
FORWARD X8
FORWARD X20
2 During play, press and hold the BACKWARD button
on the REMOTE CONTROL to search
backward at a faster speed, the search speed changes as follows:
BACKWARD X2
X20 PLAY
BACKWARD X4
BACKWARD X8
BACKWARD
NOTE : In any fast forward or fast backward mode, press the OK button to return to normal
play mode immediately.
Skipping chapters or tracks
During play, press the next SKIP
button on the REMOTE CONTROL, it moves to the next
button on the REMOTE CONTROL, it moves to the
chapter/track; press the previous SKIP
beginning of the previous chapter/track.
3. REPEAT PLAY
Allows you to repeat the current track, chapter, title, a chosen section (A-B), or all of the disc.
Each time you press the REPEAT button repeatedly, the repeat mode changes as follows:
For DVD
REP: [CHAPTER]
REP: [TITLE]
REP: [REP ALL]
REP: [OFF]
WILL REPEAT THIS
DISC OVER AND OVER
WILL REPEAT THIS CHAPTER
OVER AND OVER
WILL REPEAT THIS
TITLE OVER AND OVER
NORMAL PLAY
REPEAT A-
REPEAT A-B
A-B CANCEL
“A-B CANCEL” SHOWS AND
NORMAL PLAY RESUMES
REPEAT A TO
B
SEGMENT OVER AND OVER.
NOTE: When you select “A - B” repeat play:
1. Press the REPEAT button until “REPEAT A- ” appears at the beginning of the segment
(point A) you want to play repeatedly.
2. Press REPEAT button again at the end of the segment (point B), “REPEAT A-B” will
appear on the display.
3. The DVD player will automatically play the selected segments A to B over and over till
you press REPEAT button again.
IB-DVD1002 (AT)-WM-E-032706
16
IB-DVD1002(AT)-WM-E-032706.pmd
17
7/5/2006, 10:24 AM
3. REPEAT PLAY
For CD
REP: [REP 1]
A-B CANCEL
REP: [REP ALL]
REP: [OFF]
REPEAT A -
REPEAT A-B
For MP3
REP: [REP 1]
REP: [REP DIR]
A-B CANCEL
REP: [REP ALL]
REP: [OFF]
REPEAT A -
REPEAT A-B
4. PROGRAMMED PLAY
You can make a program of up to 16 tracks in the order you want them to be played during the
STOP mode. This feature can be used on CD and MP3.
1 Press ANGLE/PROGRAM button in the STOP mode, the screen will display the program
menu:
PROG
1 _ _ _ _ 5 _ _ _ _ 9 _ _ _ _ 13_ _ _ _
2 _ _ _ _ 6_ _ _ _ 10 _ _ _ _ 14_ _ _ _
3 _ _ _ _ 7 _ _ _ _ 11 _ _ _ _ 15_ _ _ _
4 _ _ _ _ 8 _ _ _ _ 12 _ _ _ _ 16_ _ _ _
PLAY
CLEAR
2 Press the numeric button and the direction buttons to input the track number corresponding to
the order of the track on the CD/MP3 disc you wish.
3 After programming, move the direction buttons to select “PLAY” then press the OK button, the
player will start to play the disc in the programmed order.
4 To skip to the next (programmed) track, press the NEXT
5 To stop programmed playback, press STOP button twice.
button.
IB-DVD1002 (AT)-WM-E-032706
17
IB-DVD1002(AT)-WM-E-032706.pmd
18
7/5/2006, 10:24 AM
5. SEARCH FOR PREFERRED PLAY
To select a scene with the title, the chapter,
Press SEARCH for DVD
for searching by title, chapter & time
the track number and the time during play.
1 Press the SEARCH button during play,
the screen will show as on the right:
DVD TT 01/02 CH 002/013 00:02:03
2 Move the LEFT & RIGHT DIRECTION
buttons (
&
) and press the numeric
title you want chapter you want time you want
to jump to to jump to
to jump to
buttons on the REMOTE to select the title,
the track, or the time, then press the OK
button to confirm.
Press SEARCH for CD
3 The player will jump to play the section
you selected and the menu display
disappears from the screen.
CD TRK 02/12
00:03:11
input the minute
you want to jump to
track you want
to jump to
input the second
you want to jump to
Press SEARCH for MP3
MP3 TRK 0016/154
00:01:21
input the minute
you want to jump to
track you want
to jump to
input the second
you want to jump to
(FOR DVD)
6. ZOOM PLAY
This function allows you to do a minimal zoom into a picture as well as shift the zoom point.
1 Press the ZOOM/SLOW button repeatedly to enlarge or reduce a picture. The display will show
as follows:
ZOOM 2
ZOOM 3
ZOOM 4
ZOOM 1/2
ZOOM1/3
ZOOM1/4
ZOOM: OFF
2 Press the DIRECTION buttons (
,
,
&
) to move the enlarged picture a little to up or
down, left or right.
3 To return to normal play from the ZOOM mode, press ZOOM/SLOW repeatedly till the icon
shows “ZOOM: OFF”.
NOTE: Some discs may not respond to the zoom feature and during some zoom functions the
picture edges may seem fuzzy, this is normal.
IB-DVD1002 (AT)-WM-E-032706
18
IB-DVD1002(AT)-WM-E-032706.pmd
19
7/5/2006, 10:24 AM
(JUST FOR DVD)
7. SLOW-MOTION PLAY
A disc can also be played in slow-motion.
1 Each time you press and hold the ZOOM/SLOW button during play, the playback speed will
change as follows:
2 SPrFes1s/2OK button to resume normal play from any slow-motion mode.
SF 1/4
SF 1/6
PLAY
NOTE 1: Sound will be silent during slow motion play.
NOTE 2: SF stands for SLOW FORWARD.
(DVD ONLY)
8. VIEWING FROM A DESIRED ANGLE
Some DVD video discs may contain scenes which have been shot simultaneously from a
number of different camera angles. The jacket or case of discs that are recorded with angles
will be marked with this icon:
3
For these discs, the same scene can be viewed from any of these different angles using the
ANGLE/PROGRAM button.
ANGLE 1
ANGLE 2
ANGLE 3
NOTE: 1. The recorded angles differ depending on the disc used.
2. Only some DVD discs have this feature.
3. This feature is only available on some DVDs. If it is not available on your DVD, a hand
“
” will show in the top left corner.
9. SELECTING AUDIO MODE
If a DVD disc contains a Multi-Audio soundtrack feature, you can select the desired audio
language by pressing the AUDIO button repeatedly during play, playback status will be displayed
on the TV’s screen.
Note 1: If you press the AUDIO button for several times, but the desired language is not selected,
it means the language is not available on the disc.
Note 2: This DVD player does not support DTS decoding. For DTS disc, please select
other output mode, such as AC-3; otherwise there will be no sound output.
(DVD ONLY)
10.CHANGE SUBTITLE LANGUAGE
You can select a desired subtitle quickly and easily with the SUBTITLE button.
NOTE: This operation works only with DVD discs on which multiple subtitle languages are
recorded. Some DVDs have no subtitles, some may have 5 or more. If no subtitles are
recorded on your DVD, pressing this button will not change the subtitles.
To remove subtitles, press the SUBTITLE button again till “
: [OFF] ” shows.
IB-DVD1002 (AT)-WM-E-032706
19
IB-DVD1002(AT)-WM-E-032706.pmd
20
7/5/2006, 10:24 AM
11.DISPLAYING DISC INFORMATION
If you want to know the information of the disc during play, press the DISPLAY button on the remote
control, the information will appear on the TV screen. (see below)
For DVD
The information about the title/chapter number
DVD TT 1/2 CH 6/12
00:02:35
and chapter elapsed time.
The information about the AUDIO, SUBTITLE
and ANGLE.
o)): 1/3ENG
5.1CH
2/3ENG
OFF
DVD TT 1/2 CH 6/12
DVD TT 1/2 CH 6/12
DVD TT 1/2 CH 6/12
OFF
C-00:06:41
T 00:18:05
T-01:05:40
The information about the chapter remaining
time.
The information about the title elapsed time.
The information about the title remaining time.
The information display goes off.
For CD
The information about the current track
elapsed time.
CD TRK 2/12
00:01:03
The information about the current track
remaining time.
CD TRK 2/12
C-00:02:42
The information about the total track elapsed
time.
CD TRK 2/12
CD TRK 2/12
T 00:10:49
T-00:40:35
The information about the total track remaining
time.
The information display goes off.
OFF
For MP3
The information about the current track
elapsed time.
MP3 TRK 2/124
00:03:03
The information about the current track
remaining time.
MP3 TRK 2/124
OFF
C-00:01:36
The information display goes off.
NOTE 1: “TT” stands for title, “CH” stands for chapter.
NOTE 2: Depending on the disc, the above information may not appear or you may not be able to
change the display.
IB-DVD1002 (AT)-WM-E-032706
20
IB-DVD1002(AT)-WM-E-032706.pmd
21
7/5/2006, 10:24 AM
12. MP3 DISC OPERATION
This allows you to play your MP3 recorded disc on this set.
1 Load your recorded MP3 disc into the player, a menu will show on the screen.
[MP3]01-------MP3
01.MP3
01.01
02.02
03.03
04.04
05.05
06.06
07.07
08.08
09.09
10.10
2 Select the desired file by pressing the
or
button.
3 Press OK button to open the file and start playing.
4 Select the desired track by pressing the
5 Press OK button to start playback.
or
button.
6 You may use the PREVIOUS
or NEXT
button to skip to the previous or next track.
7 Press and hold
or
button for fast backward or fast forward play.
8 Press STOP button to stop playing.
13. JPEG OR PICTURE DISC OPERATION
This allows you to play your JPEG or picture disc on this set.
1 Load a JPEG disc or picture CD disc into the player, a menu will show on the screen.
2 Go to the menu of directory which you want to view by using the DIRECTION buttons, press OK
button to start the JPEG play.
3 During the picture is being displayed, use these
left or right.
/
/
/
buttons to rotate it in invert, mirror,
4 Press the ZOOM/SLOW button repeatedly to reduce or enlarge a picture. The display will show
as follows:
ZOOM 2
ZOOM 3
ZOOM 4
ZOOM 1/2
ZOOM1/3
ZOOM1/4
ZOOM: OFF
To move the enlarged picture a little to up or down, left or right, press these
/
/
/
buttons.
To return to normal view, press ZOOM/SLOW button till “ZOOM: OFF” shows on the screen.
5 Press the NEXT
button to see the next image in your folder.
6 Each picture in the current directory will be displayed consecutively in a slide show
presentation.
IB-DVD1002 (AT)-WM-E-032706
21
IB-DVD1002(AT)-WM-E-032706.pmd
22
7/5/2006, 10:24 AM
TROUBLE SHOOTING
Symptom
Remedy
Insert the AC power plug securely into the power outlet. Make
No power.
sure your outlet has power. Check the outlet with a lamp.
1. The disc may be damaged or scratched.
2. This player cannot play a DVD disc other than region 1 standard.
3. The disc may be dirty and may require cleaning.
4. Ensure that the disc is installed with the label side up (facing you).
5. If your disc is rented, it may be scratched or damaged from a
previous renter, you may fix a disk with a polishing machine.
6. Condensation may have formed on your disc. Wait about 1
hour to allow the player to dry out.
• Play fails to start even
when OK is pressed.
• Play starts but then
stops immediately.
1. Ensure that the equipment is connected properly. Double
check all cables and AC power.
2. Select the proper video channel on your TV set VIDEO or
CHANNELS 1, 2, 3, etc.
No picture.
3. Check if the proper AV input is selected on your TV set video
inputs (some TV sets have 3 or 4 different inputs). You may
have to press the VIDEO button on your TV.
4. Make sure both the TV and DVD player are on.
1. Press AUDIO button several times. The disc may have been
set to DTS output or a blank audio channel on multiple language,
please select AC-3 output or reset to the main language.
2. Make sure the AUDIO output connection and settings are
correct. See details on pages 13 &14.
• No sound.
• Distorted sound.
3. Ensure that the equipment is connected properly.
4. Ensure that the input setting for the TV and stereo system
are correct.
5. Adjust volume setting on your TV’s remote or DVD’s remote.
6. Ensure the MUTE button is not pressed on your TV’s remote or
DVD’s remote (If yes, press the MUTE button again).
1.Picture is distorted during rapid advance or rapid reverse.
The picture may be somewhat distorted at times, this is normal.
2.Do you connect your DVD player to your VCR? Please
disconnect from VCR.
Picture is distorted.
1. Check that the batteries are installed correctly.
2. The batteries are weak or depleted, replace them with new ones.
3. Point the remote control unit at a distance of less than 20 feet
(6m) from the DVD player.
The REMOTE
CONTROL unit
does not work.
4. Remove any obstacles between the remote control unit and
remote control sensor.
No rapid advance or
rapid reverse play.
Some discs may have sections which prohibit rapid advance
(or rapid reverse), especially on opening screens.
Faces are too long or no
4:3 (16:9) picture.
Choose the correct setup item which matches the TV set used,
or change the display type to 4:3 LB (see Page 12).
Cabinet vibrates or
hums during play.
This is normal for high speed reading of DVD discs.
“Wrong Region” shows Press the OPEN button and replace a good Region 1 disc into
on left top corner.
the player. This player only plays region 1 DVD discs.
IB-DVD1002 (AT)-WM-E-032706
22
IB-DVD1002(AT)-WM-E-032706.pmd
23
7/5/2006, 10:24 AM
TROUBLE SHOOTING
Symptom
Remedy
Press the ON/STANDBY button on the remote to set the player to
the standby mode and then press the ON/STANDBY button again
to turn the player to ON. Reset the DVD player by disconnecting
the power plug and then re-connecting it (the player may not be
operating properly due to lightning, static electricity, damaged or
wrong discs, or some other external factors).
No button operates (on
the main unit and/or the
REMOTE CONTROL
unit).
Cannot change a menu
item.
Try changing this item with the DVD door open (not during play).
Audio soundtrack and/ If the audio soundtrack and / or subtitle language does not exist
or subtitle language is on the disc, the language selected at the initial setting will not be
heard/seen. Try setting it up again, see Page 13.
not at the initial settings.
Subtitles appear only on discs which contain them.
If subtitles don’t show, press the SUBTITLE button to display
the subtitles.
No subtitles.
An alternative language is not possible with discs which do not
have more than one language. In the case of some discs, the
alternative language cannot be selected by operating the AUDIO
or SUBTITLE buttons. Try selecting it from the DVD menu if one
is available.
Alternative
audio
soundtrack (or subtitle)
Language does not
show.
This function is dependent on the DVD disc. Even if a disc has a
number of angles recorded, these angles may be seen only on
specific scenes.
Angle cannot be
changed.
If faces seem stretched and too long, your TV shape may be
adjusted to 16:9 ratio. Please adjust it to 4:3 for better results or
match to your TV type, see page 12.
Images appear distorted.
1. Buy a newer TV with these jacks.
2. You may try using your VCR’s jacks but the color may be
distorted due to macrovision licensed DVD protection (against
copying discs).
If your TV set does not
have Audio / Video input
jacks.
3. Your dealer can sell you an RF Modulator which converts the
signals for inputting into the TV’s RF input (antenna) jacks.
However, your results will never be as good as a new modern
TV with proper input jacks.
If a button is pressed too fast over and over, the signals may jam
the circuits inside. To restore to normal, press STOP button and
open the disc door to reset the circuits.
Picture is frozen.
Screen saver appears Turn off screen saver by pressing any button on the REMOTE
on TV screen.
control.
Can not copy discs to
VHS video tapes.
You can’t copy most commercial movie discs due to copy
protection built into the disc.
Picture is too short.
Change the picture screen type, see page 12.
1. Check your cables if output matches input.
Progressive scan
2. Does your TV support progressive scan? if not, use normal or
S-Video jacks, set your player to S-Video output. (see page 14.)
doesn’t work.
IB-DVD1002 (AT)-WM-E-032706
23
IB-DVD1002(AT)-WM-E-032706.pmd
24
7/5/2006, 10:24 AM
GLOSSARY
Title
PAL
The longest sections of a picture or a music
piece on a DVD, or a movie, etc., for a picture
piece on video software; or an album, etc., for
a music piece on an audio software. Each title
is assigned a title number enabling you to
locate the title you want.
Phase Alternation Line: a video standard used
in Europe.
YUV
A video standard, it can optimize the translation
of the Video, Y means Luminance, U and V mean
chrominance.
CHAPTER
S-Video Cable
Sections of a picture or a music piece on a
DVD that are smaller than titles. A title is
composed of several chapters. Each chapter
is assigned a chapter number enabling you to
locate the chapter you want.
This cable can connect to your S-Video input
of your TV. It allows for sharper pictures for
TV sets with this jack. However the sharpest
clearest pictures can be seen when using a
Component Video cable.
JPEG
Video Cable
JPEG is short for the “Joint Photographic Ex-
perts Group”, a group of experts nominated
to produce standards for continuous tone im-
age coding. In other words, your DVD player
can view digital picture CDs or CDs you made
on your computer with file names that end in
This is a wire with plugs on each end which is
used to connect the picture information into
your TV set.
Video Input
This is a jack which accepts the picture portion
of a signal. In order to use this DVD player,
your TV set must have an S-Video (better) or
Video input (standard) jack.
the “.JPG” format.
PROGRESSIVE SCAN
Progressive scan, creates a picture signal with
double the scan lines of a conventional interlaced
picture. It creates a noticeably sharper image
and can offer higher picture resolution and
eliminates virtually all motion artifacts. Even on
large screens, the progressive scan lines are
barely noticeable and picture flickering is greatly
reduced, so you can enjoy extended viewing
without eye fatigue. Our progressive-scan DVD
players can handle both progressive and
conventional interlaced video.
ABOUT DVD REGION
MANAGEMENT
The DVD inventors and motion
picture makers have decided to
break up the world’s DVDs into
regions so that one country’s
DVDs should not be able to play in another
country.
This is a legal issue and that is why your
DVD player is restricted to play only region 1
DVDs.
NTSC
National TV Systems Committee for TV
broadcasts: a video standard used in the USA
and Canada.
IB-DVD1002 (AT)-WM-E-032706
24
IB-DVD1002(AT)-WM-E-032706.pmd
25
7/5/2006, 10:24 AM
SPECIFICATIONS
General Description
Power source:
AC 100 – 240V, 50/60Hz
Power consumption:
15 Watts [normal household current] (approx. 5W when the set is in
the standby mode).
Signal system:
NTSC/PAL TV system
Video output level:
Audio output level:
Dimensions (Approx.):
1 Vp-p
2 Vrms (1 kHz, 0dB)
Width: 251 mm
9 7/8"
Depth: 171 mm 6 3/4"
Height: 48 mm
Weight: 0.8 kg
1 7/8"
1.8 lbs
Audio Signal Output Characteristics:
DVD (linear audio):
(1) Frequency response:
4Hz-22kHz (48 kHz sampling)
4Hz-44kHz (96 kHz sampling)
(2) S/N ratio: 100dB
(3) Dynamic range: 90 dB
(4) Wow and flutter: below measurable level
CD audio:
(1) Frequency response: 20 Hz - 20 kHz
(2) S/N ratio: 65dB
Pickup: Wave length: 650nm~660nm
Laser power: Class 1
(3) Dynamic range: 90 dB
(4) Wow and flutter: below measurable level
We reserve the right to make design and specification changes for product improvement.
The descriptions and characteristics given in this document are given as a general indication
and not as a guarantee. In order to provide the highest quality product possible, we reserve
the right to make any improvement or modification without prior notice. The English version
serves as the final reference on all product and operation details should any discrepancies
arise in other languages.
PROTECT YOUR FINE FURNITURE!
WE RECOMMEND A PROTECTIVE MATERIAL BE PLACED UNDER THE SET WHEN PLACING
IT ON SURFACE WITH A NATURAL OR LACQUER FINISH.
IB-DVD1002 (AT)-WM-E-032706
25
IB-DVD1002(AT)-WM-E-032706.pmd
26
7/5/2006, 10:24 AM
LIMITED WARRANTY
We warrant this product to be free from defects in material and workmanship under normal
use for a period of 1 year after purchase, and we will repair it free of charge or replace it at no
charge, should it become defective under this warranty, providing you submit proof of purchase
(sales slip) with the set.
During the initial 1 year period after original purchase, we will service the set that is returned
to LENOXX ELECTRONICS CORP., prepaid, at no charge. After the initial 1 year period expires,
we will exchange, at no charge, any part that is defective, but will charge for the cost of labor,
return postage paid by Lenoxx.
This warranty does not apply to any product which has been subject to misuse, neglect or
accident. This warranty does not cover a broken cord or cabinet. UNDER NO CIRCUMSTANCES
WILL LENOXX ELECTRONICS CORP. BE LIABLE FOR ANY INCIDENTAL OR CONSEQUEN-
TIAL DAMAGES. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state. The following charges apply to repairs beyond the warranty period: $ 20.00.
Be sure to pack carefully and return postage paid insured together with your money
order (personal checks will not be accepted) and sales receipt to:
LENOXX ELECTRONICS CORP., 35 BRUNSWICK AVENUE, EDISON, N.J. 08817, USA
For Customer Service
Dial: 1-800-315-5885
(MONDAY - THURSDAY 8:00 AM - 5:00 PM, FRIDAY 8:00 AM - 1:30 PM EST)
or Email: [email protected]
© 2006 LENOXX ELECTRONICS CORP.
35 BRUNSWICK AVENUE
EDISON, N.J. 08817, USA
MADE & PRINTED IN CHINA
IB-DVD1002 (AT)-WM-E-032706
26
IB-DVD1002(AT)-WM-E-032706.pmd
27
7/5/2006, 10:24 AM
|