LevelOne Computer Hardware FNC 0115 User Manual

FNC-0115  
100FX Multi-mode SC Fiber Optic PCI Express Card  
User Manual  
Ver. 1.00-0801  
 
Caution  
Circuit devices are sensitive to static electricity, which can damage their delicate  
electronics. Dry weather conditions or walking across a carpeted floor may cause you to  
acquire a static electrical charge.  
To protect your device, always:  
Touch the metal chassis of your computer to ground the static electrical charge before  
you pick up the circuit device.  
Pick up the device by holding it on the left and right edges only.  
Electronic Emission Notices  
Federal Communications Commission (FCC) Statement  
This equipment has been tested and found to comply with the limits for a class B  
computing device pursuant to Subpart J of part 15 of FCC Rules, which are designed to  
provide reasonable protection against such interference when operated in a commercial  
environment.  
European Community (CE) Electromagnetic Compatibility Directive  
This equipment has been tested and found to comply with the protection requirements  
of European Emission Standard EN55022/EN60555-2 and the Generic European Immunity  
Standard EN50082-1.  
EMC:  
EN55022(1988)/CISPR-22(1985) class B  
EN60555-2(1995)  
EN60555-3  
class B  
IEC1000-4-2(1995)  
IEC1000-4-3(1995)  
IEC1000-4-4(1995)  
4K V CD, 8KV, AD  
3V/m  
1KV – (power line), 0.5KV – (signal line)  
 
1. Overview  
Fast Ethernet PCI-e 100Base-FX Fiber Adapter is a Fast Ethernet Board that fully  
complies with all IEEE 802.3u and 100Base-FX standards. Two LED indicators  
(LINK/ACT and FDX) on the bracket will help to oversee the board link, activities  
and full-duplex status.  
Fast Ethernet PCI-e 100Base-FX Fiber adapters support Pre-boot Execution  
Environment (PXE), Remote Program Load (RPL), and Bootstrap Protocol  
(BOOTP). Multi-Boot Agent (MBA) is a software module that allows your networked  
system to boot with the images provided by remote systems across the network.  
2. Checklist  
Before you start installing the PCI-e 100Base-FX Fiber Adapter, verify that the  
package contains the following items:  
Fast Ethernet PCI-e 100Base-FX Fiber Adapter  
LAN Driver and User’s Guide CD-ROM  
Please notify your sales representative immediately if any of the aforementioned  
items is missing or damaged.  
3. Model Description  
PCI-e 100Base-FX Board Models  
Fiber Transceiver  
SC multi-mode  
Wavelength  
1310nm  
4. Network Remote Boot Configuration  
4.1 Select Remote Boot Type  
For entering “MBA Configuration Menu” to select Remote Boot Type (PXE,  
RPL), please press Shift-F10 within 3 seconds after power on your PC,  
otherwise, the system would go to Windows O.S.  
4.2 Set Network Remote Boot  
For setting network remote boot, please enter PC BIOS first, then select  
“Boot” tab, after that, choose “MBA” as the priority first boot device.  
4.3 Cancel Network Remote Boot  
To cancel network remote boot, please change the “Boot” setting in PC  
BIOS from “MBA” to “Hard Drive” or other devices.  
1
 
5. LED Description  
LED  
LINK/ACT  
FDX  
Color  
Green  
Green  
Function  
Lit when cable connection is good  
and speed is at 100Mbps.  
Blinks when any traffic is present.  
Lit when full-duplex mode is active.  
6. Wake on LAN  
The Wake on LAN function on this adapter can recognize a wake-up frame and  
signal the PC to power up.  
The default value of WOL (Wake on LAN) function is ON. You can also disable the  
WOL function by putting the jumper on the pin 1 and pin 2.  
Never drop the jumper, otherwise FNC-0115 will be lack of electricity.  
J1  
3
2
ON  
OFF  
1
Wake on LAN select Jumper (J1)  
2
 
7. Network Parameter  
Multi-mode Fiber 62.5/125um, 50/125um  
Full Duplex  
2000m  
LINK/ACT  
FDX  
TX  
RX  
Fig. 1 Diagnostic LEDs and Bracket  
3
 
8. Technical Specifications  
Standards  
: IEEE 802.3u Fast Ethernet 100Base-FX  
IEEE 802.3x Full-Duplex Flow Control  
IEEE 802.1Q VLAN  
Connector  
: 1310nm SC multi-mode  
Fiber Optic Cable:  
62.5/125, 50/125  
µm multi-mode  
Data Transfer Mode/Speed:  
Full duplex (Default) mode  
100Mbps speed  
Diagnostics LED on Bracket:  
LINK/ACT  
FDX  
Bus Slot  
: PCI-e 1.0 Compliant  
Power Requirement : Max. 3W, +3.3VDC@1A  
Ambient Temperature : 0° to 50°C  
Humidity  
Emission  
: 5% to 90%  
: Complies with EMI Standard  
FCC Class B  
CE Mark  
4
 

Kustom Musical Instrument Amplifier KXB200H HR User Manual
Lenmar Enterprises Battery Charger BCR336 User Manual
Lenovo Switch H415 User Manual
Lincoln Electric Welding System IM10055 User Manual
Link electronic Stereo Amplifier PVA 851 User Manual
Listen Technologies Satellite Radio LR 500 User Manual
Makita Blower BUB360 User Manual
Mattel Motorized Toy Car Y9172 0920 User Manual
Maytag Range W10667178A User Manual
Melissa Microwave Oven ED8525NS SA User Manual