SX30 Cross-trainer
U S E R M A N U A L
Before using this product, it is essential to read this
ENTIRE operation manual and ALL installation instructions.
This will help in setting up the equipment quickly
and in instructing others on how to use it correctly and safely.
FCC Warning - Possible Radio / Television Interference
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a resi-
dential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used
in accordance with the operation manual, may cause harmful interference to radio communications. However, there is no
guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Class HB (Home): Domestic use. Not suitable for therapeutic purposes.
CAUTION: Any changes or modifications to this equipment could void the product warranty.
Any service, other than cleaning or user maintenance, must be performed by an authorized service representative. There
are no user-serviceable parts.
2
TABLE OF CONTENTS
Unpacking and Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
1.
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Where to Place the Cross-trainer // How to Stabilize the Cross-trainer // Plug In the Cross-trainer
The Display Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
The Display Console Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Display Console Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
The Reading Rack and Water Bottle Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Correct Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Mounting and dismounting the Cross-Trainer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Biomechanical Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
General // Forward Motion – Total Body // Reverse Motion – Total Body // Braking Resistance
1.1
1.2
2
2.1
2.2
2.3
3.
3.1
3.2
4
The Workouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Workout Overviews . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Setting Up and Using the Workouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
4.1
4.2
Selecting and Using Quick Start Manual Mode // Selecting a Workout // Entering a Duration //
Selecting and Adjusting the Intensity Level // Starting a Workout // Pausing a Workout //
Resetting a Workout // Reviewing a Completed Workout // Understanding the Heart Rate Zone
to Maximize Workout Benefits
4.3
5
Workout Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Service and Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Preventative Maintenance Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Preventative Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
How to Obtain Product Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Cross-trainer Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
5.1
5.2
5.3
5.4
© 2002 Life Fitness, a division of Brunswick Corporation. All rights reserved. Life Fitness is a registered trademark of Brunswick
Corporation. Sport is a trademark of Brunswick Corporation. Any use of these trademark, without the express written consent of Life
Fitness is forbidden.
3
UNPACKING THE CROSS-TRAINER
1. Carefully cut and remove the SHIPPING BANDS.
2. Carefully cut the tape securing the TOP FLAPS.
3. Fold the TOP FLAPS outward fully.
7. With the help of another person, carefully lift the BASE
UNIT from the SHIPPING CARTON. Remove the pro-
tective packaging from the unit
4. Remove the UPRIGHT TUBE ASSEMBLY and PEDAL
LEVER. Remove the CENTER STYROFOAM SPAC-
ER.
5. Remove all remaining components, parts bags, and
styrofoam packaging until only the base unit remains.
6. Remove the OUTER SHIPPING SLEEVE.
4
ASSEMBLING THE CROSS-TRAINER
Tools required: Metric Socket set, Phillips
Screwdriver, Metric Wrench set
8. Locate the user right PEDAL LEVER (L) and PEDAL (M).
Position the PEDAL above the PEDAL MOUNTING PLATE
(N) and secure the PEDAL using four SCREWS (13) and
LOCK WASHERS (14). Tighten the SCREWS securely.
Repeat for the user left PEDAL (O) and PEDAL LEVER (P).
1. Position the base unit near the desired location for use
(Refer to the "Getting Started" section of this manual for
proper location). Locate and install the four LEVELER FEET
(A) into the front and rear STABILIZERS as shown.
2. With the DISPLAY CONSOLE MOUNTING PLATE (B) facing
upward, lay the UPRIGHT TUBE ASSEMBLY (C) on floor in
front of BASE FRAME (D). Cut the wire tie securing the
LOWER WIRE HARNESS (E) to the front of the BASE
FRAME. Connect the UPPER WIRE HARNESS (F) to the
LOWER WIRE HARNESS.
9. Position the rear end of the user right PEDAL LEVER (L)
near the user right REAR CLEVIS (Q). Position the end of
the PEDAL LEVER between the clevis flanges. Align the
holes and secure as shown using two CAP WASHERS (2),
one 3 1/4" BOLT (15), one NUT (16) and two PLASTIC
COVER CAPS (5). Tighten the BOLT and NUT securely.
3. Position the UPRIGHT TUBE ASSEMBLY (C) between the
plates on the front of the BASE FRAME (D). Feed any
excess wire harness into the BASE FRAME. Tilt the
UPRIGHT TUBE ASSEMBLY into an upright position. Align
the holes on the plates with the holes on the UPRIGHT
TUBE ASSEMBLY. Secure the UPRIGHT TUBE ASSEMBLY
to the BASE FRAME using four 2-3/4" BOLTS (1), eight CAP
WASHERS (2) (4 on each side) and four NUTS (3). Tighten
until snug.
10. Lift the front end of the user right PEDAL LEVER (L) to meet
the user right ROCKER ARM CLEVIS (R). Secure the
PEDAL LEVER to the ROCKER ARM CLEVIS using two
CAP WASHERS (2), one 3 1/4" BOLT (15), one NUT (16)
and two PLASTIC COVER CAPS (5). Tighten the BOLT and
NUT securely. Repeat the procedure for the user left PEDAL
LEVER (P) and ROCKER ARM CLEVIS (S).
11. Position the DISPLAY CONSOLE (T) over the DISPLAY
CONSOLE MOUNTING PLATE (B) located at the top of the
UPRIGHT TUBE ASSEMBLY (C). Plug the CONNECTOR
(U) leading from the DISPLAY CONSOLE MOUNTING
PLATE into the corresponding CONNECTOR in the back of
the DISPLAY CONSOLE. Make sure the connector snaps
into place. Push excess wire harness into the opening of the
DISPLAY CONSOLE MOUNTING PLATE.
4. Using two 1" BOLTS (4), secure the UPRIGHT TUBE
ASSEMBLY (C) to the backside of the connector joint on the
BASE FRAME (D). Tighten all the BOLTS securely. Install
eight black PLASTIC COVER CAPS (5) over each 2-3/4"
BOLT HEAD (1 & 4) and NUT (3).
5. Slide the tab of the UPRIGHT TUBE ANGLE BRACE (G)
into the slot located near the base of the UPRIGHT TUBE
ASSEMBLY (C) and pivot the UPRIGHT TUBE ANGLE
BRACE downward to met the BASE FRAME (D). Using two
screws (6) secure the UPRIGHT TUBE ANGLE BRACE to
the UPRIGHT TUBE ASSEMBLY and BASE FRAME as
shown.
12. Secure the DISPLAY CONSOLE (T) to the DISPLAY CON-
SOLE MOUNTING PLATE (B) using four SCREWS (17).
Tighten the screws securely.
CAUTION: Be careful not to pinch the wire harness
when assembling the DISPLAY CONSOLE (T) to the
DISPLAY CONSOLE MOUNTING PLATE (B).
6. Slide one LARGE FLAT WASHER (7) and one LARGE
WAVE WASHER (8) onto the user right PIVOT SHAFT (H).
Slide the WASHERS fully over the PIVOT SHAFT until seat-
ed against the pre-installed STOP RING.
13. Secure the WATER BOTTLE BRACKET (V) to the UPRIGHT
TUBE ASSEMBLY (C) as shown using two SCREWS (18).
Tighten the SCREWS securely. Insert the WATER BOTTLE
(W) into the WATER BOTTLE BRACKET.
7. Locate the user right ROCKER ARM ASSEMBLY (J)
(Marked with an “R”). With the top handgrip facing the front
of the unit (as shown), slide the user right ROCKER ARM
ASSEMBLY onto the user right PIVOT SHAFT (H) until seat-
ed against the WASHERS (7 & 8). Secure the ROCKER
ARM ASSEMBLY to the PIVOT SHAFT using one FLAT
WASHER (9), LOCK WASHER (10), and 1-1/4” HEX BOLT
(11). Tighten the BOLT securely. Insert one ROCKER ARM
END CAP (12) into the end of the ROCKER ARM SHAFT.
Repeat the procedure for the user left ROCKER ARM
ASSEMBLY (K).
14. Locate the REAR STABILIZER END CAPS (X). Insert one
REAR STABILIZER END CAP into either end of the REAR
STABILIZER.
15. Refer to the "Getting Started" section of this manual for prop-
er location, stabilizing, and POWER ADAPTER instructions.
5
This Operation Manual describes the functions of the following products:
Life Fitness SportTM cross-trainer:
SX30
See Section 7, titled Specifications page in this manual
for product-specific features.
Statement of Purpose: The cross-trainer is an exercise machine that combines low-impact elliptical pedaling with
push/pull arm motion to provide an efficient, effective total body workout.
Health-related injuries may result from incorrect or excessive use of exercise equipment. The manufacturer
STRONGLY recommends seeing a physician for a complete medical exam before undertaking an exercise
program, particularly if the user has a family history of high blood pressure or heart disease; or is over the
age of 45; or smokes, has high cholesterol, is obese, or has not exercised regularly in the past year. The
manufacturer also recommends consulting a fitness professional on the correct use of this product.
If, at any time while exercising, the user experiences faintness, dizziness, pain, or shortness of breath, he or she
must stop immediately.
6
1
GETTING STARTED
1.1 IMPORTANT SAFETY INSTRUCTIONS
SAFETY WARNING: The safety of the product can be maintained only if it is examined regularly for
damage and wear. See Preventative Maintenance section for details.
•
Before using this product, it is essential to read this ENTIRE operation manual and ALL instructions. The cross-train-
er is intended for use solely in the manner described in this manual.
•
•
•
Always follow the console instructions for proper operation.
Close supervision is necessary when used by or near children, invalids or disabled persons.
If the cross-trainer does not function properly after it has been dropped, damaged, or even partially immersed in
water, contact Customer Support Services for assistance.
•
•
Never insert objects into any opening in the cross-trainer. If an object should drop inside, carefully retrieve it. If the
item is beyond reach, contact Customer Support Services.
Never place liquids of any type directly on the unit, except in an accessory tray. Containers with lids are
recommended.
•
•
•
•
•
Do not use the cross-trainer outdoors, near swimming pools or in areas of high humidity.
Keep all loose clothing, shoelaces, and towels away from the cross-trainer pedals.
Keep the area around the cross-trainer clear of any obstructions, including walls and furniture.
Use caution when mounting or dismounting the cross-trainer. While exercising, always hold onto the user arms.
Never operate a Life Fitness product if it has a damaged power cord or electrical plug, or if it has been dropped,
damaged, or even partially immersed in water. Contact Life Fitness Customer Support Services.
•
Keep the power cord away from heated surfaces. Do not pull the equipment by the power cord or use the cord as a
handle.
•
•
Do not run the power cord on the floor under or alongside of the Cross-Trainer.
Wear shoes with rubber or high-traction soles. Do not use shoes with heels, leather soles, cleats or spikes. Do not
use the cross-trainer in bare feet.
•
•
•
Do not tip the cross-trainer on its side during operation.
Keep hands and feet away from all moving parts.
To ensure proper functioning of this product, do not install attachments or accessories that are not provided or
recommended by Life Fitness.
•
•
•
Use this product in a well-ventillated area.
Use this product on a solid, level surface.
Make sure that all components are fastened securely.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
7
1.2 SETUP
Read the entire Operation Manual before setting up the cross-trainer.
WHERE TO PLACE THE CROSS-TRAINER
Following all safety instructions in Section 1.1, move the cross-trainer to the location in which it will be used. See
Section 5, titled Specifications, for the dimensions of the footprint. Allow one foot (30.4 cm) of clearance in front of the
cross-trainer to allow for movement of the pedal levers. It should be easy to mount the cross-trainer from the side.
HOW TO STABILIZE THE CROSS-TRAINER
After placing the cross-trainer in position, check the unit's stability by attempting to rock it in all directions. Any slight rocking
indicates that the unit must be leveled. Determine which foot is not resting completely on the floor. Loosen the jam nut (A) with
an open-end 17mm wrench, and rotate the stabilizing foot (B) to lower it. Verify that the cross-trainer is stable, and repeat the
adjustment as necessary until the unit no longer rocks. Lock the adjustment by tightening the jam nut against the stabilizer bar.
It is extremely important that the stabilizing leg be correctly adjusted for proper operation.
PLUG IN THE CROSS-TRAINER
The cross-trainer comes with a standard power supply for the U.S., or a power supply with country-specific line cords.
Insert the power adapter jack (C) into the barrel plug on the back of the cross-trainer. Then insert the power supply into
the wall outlet. Make sure the cord is routed so that it doesn't bind and will not be walked on.
Check that the console LEDs light up. If not, recheck the plug and wall connections and make sure the wall outlet has
power.
8
2
THE DISPLAY CONSOLE
2.1 DISPLAY CONSOLE OVERVIEW
The computerized display console on the cross-trainer allows the user to tailor a workout to personal fitness abilities and
goals and to monitor progress. With this easy-to-use console the user can track fitness improvement from one workout to
the next.
9
2.2 DISPLAY CONSOLE DESCRIPTIONS
The functions for the keys and display windows on the cross-trainer console are listed and described in this section. See
Section 4, titled The Workouts, for detailed information on using the console to set up workouts.
A
START/STOP/HOLD TO PRESET: Use this key to initiate a number of different functions on the cross-trainer.
•
•
•
•
•
Begining a 30-minute QUICK-START MANUAL workout immediately, without setup steps
Beginning a workout after completing the setup steps for a specific workout
Pausing a workout-in-progress
Restarting a paused workout
Deleting a current workout and making it possible to set up a new workout
B
C
ENTER: Press this key to accept information displayed by the console when setting up a workout.
ARROW KEYS: Use these keys when setting up a workout to change displayed values for workout type, duration,
and resistance level. When a workout is in progress, use these keys to change the intensity level.
D
SCROLL: During a workout-in-progress, press this key to browse through workout statistics displayed in the bottom
data window. Each time the SCROLL key is pressed, a different value is displayed, and it’s corresponding light emit-
ting diode (LED) lights up simultaneously. When the Scan LED lights up, the lower DATA window automatically dis-
plays all statistics in rotating succession.
Press this key to view summary data for a completed workout, including total calories burned and total distance traveled
E
DATA WINDOWS: Two data windows are set in the center of the console display.
The top window displays the following statistics. Depending on which statistic is being displayed at any given
instance, the corresponding LED lights up at the same time.
•
Time: The elapsed time of a workout-in-progress. During a workout setup, this window also shows the default
duration of 30 minutes, which the user change using the ARROW keys.
•
Weight: The user’s selected weight.
The bottom window displays the following statistics in an alternating rotation for a workout-in-progress. Depending on
which statistic is being displayed at any given instance, the corresponding LED lights up at the same time.
•
•
•
•
RPM (Revolutions Per Minute): The pedaling speed or rate
Distance: The total distance traveled
Calories: The number of calories burned
Level: The resistance level of the current interval of a workout-in-progress
F
WORKOUT LED INDICATORS: One set of LEDs is matched to the cross-trainer’s set of workout options. During a
workout setup, each time the user presses an ARROW key to view another workout option, one of these LEDs lights
up to indicate that the corresponding workout is the currently displayed option. While a workout-in-progress, the LED
corresponding to that workout remains lit up.
Another set of LEDs is matched to a set of workout statistics. See the DATA WINDOWS description above.
The LED labeled “scan” lights up during a workout-in-progress to indicate that the console is alternately displaying
RPM, Distance, Calories and Level in the bottom DATA WINDOW.
See the SCROLL key and DATA WINDOW descriptions above for more information.
G
DOT MATRIX DISPLAY: This window displays a workout’s profile, which consists of columns of light that represent
the levels of intensity of each interval. During the setup for a RANDOM workout, this window displays computer-
generated profile options, which the user can browse using the ARROW keys.
10
2.3 THE READING RACK AND WATER BOTTLE HOLDER
A reading rack (A) for supporting a book or magazine is located at the base of the upper panel of the console.
A water bottle holder (B) is mounted on the monocolumn of the cross-trainer.
11
3
CORRECT USAGE
3.1 MOUNTING AND DISMOUNTING THE CROSS-TRAINER
If mounting from the user right side of the Cross-Trainer, grasp the user right handlebar with the right hand. Place the right foot
on the user right pedal and carefully step over the Cross-Trainer, grasp the user left handlebar with the left hand, and place the
left foot on the user left pedal. If mounting from the user left side, proceed in an opposite fashion. Reverse the process to dis-
mount the Cross-Trainer.
3.2 BIOMECHANICAL GUIDELINES
There are two exercise variations that can be performed on the Cross-Trainer. For each variation, it is important to follow these
general biomechanical guidelines as well as the specific instructions listed below.
GENERAL
• Feet should be in a comfortable position facing forward on the pedals so the knees move in a forward plane (not angled
inward or outward) and so the hips do not rotate outward.
• Keep back straight. Do not bend forward at the waist.
• Keep both feet on the pedals at all times.
• If desired, allow heels to slightly lift off the pedals during the motion.
• Do not lock knees during the workout. Keep them slightly bent throughout the motion.
FORWARD MOTION – TOTAL BODY
• Mount the Cross-Trainer facing forward
• Hands should be positioned comfortably on the moving handles such that the elbow creates a 90 degree angle when the
moving handlebar is rotated toward you
• Choose the desired workout profile and duration on the console
• Begin moving feet in a smooth forward pedaling motion by pushing top foot forward and pulling bottom foot backward
• Exercise at a speed that is comfortable for you
REVERSE MOTION – TOTAL BODY
• Mount the Cross-Trainer facing forward
• Hands should be positioned comfortably on the moving handles such that the elbow creates a 90 degree angle when the
moving handlebar is rotated toward you
• Choose the desired workout profile and duration on the console
• Begin moving feet in a smooth reverse pedaling motion by pulling top foot backward and pushing bottom foot forward
• Exercise at a speed that is comfortable for you
BRAKING RESISTANCE
The Life Fitness Cross-Trainer features speed-dependent braking resistance. For a set resistance level on the monitor, the resistance
increases with speed. The faster you go, the greater the resistance. The computer makes no adjustments to maintain the resistance
level based on your speed.
12
4
THE WORKOUTS
4.1 WORKOUT OVERVIEWS
This section lists the cross-trainer’s pre-programmed workouts. For more detailed information, see Section 4.2, titled
Setting Up and Using the Workouts.
QUICK START MANUAL MODE is the fastest way to begin exercising, and it bypasses the steps involved in selecting a
specific workout program. After the START key is pressed, a constant-level workout begins. The resistance level does
not change automatically.
INTERVAL combines “hills” and “valleys” of different resistance levels, which is proven to provide effective,
time-efficient cardiovascular results.
RANDOM is an interval training workout for which the user selects a computer-generated profile of varying intensity
levels.
MANUAL is a workout in which the resistance level does not change automatically.
PEAK is intended to burn fat by building up to, and maintaining, a constant level of resistance throughout the workout.
SLOPE gradually increases the intensity throughout the workout duration. It is intended to strengthen the heart, as well
as the major muscle groups that are most active during the workout, such as the leg muscle groups.
CHALLENGE begins at a high resistance level and maintains this level throughout the duration.
4.2 SETTING UP AND USING THE WORKOUTS
To activate the console, press any key, or simply start pedaling. When the console display lights up, either select
QUICK START MANUAL MODE, or select a specific workout. Setting up a specific workout involves three steps, which
are described in this section:
1. Selecting a workout
2. Entering a workout duration
3. Entering a weight
4. Selecting a difficulty level
5. Starting the workout (pressing START)
SELECTING AND USING QUICK START MANUAL MODE
Press the START key to begin a 30-minute MANUAL workout immediately. Once the workout is in progress, it is possible
to change the resistance level using the ARROW keys.
SELECTING A WORKOUT
For INTERVAL, MANUAL, PEAK, SLOPE, and CHALLENGE: Press the ARROW KEYS until the LED display for the
desired workout lights up. Then, press ENTER to confirm the workout selection.
For RANDOM: Press the ARROW KEYS until the LED display for the RANDOM workout lights up. Then, press ENTER. The
first computer-generated RANDOM workout profile appears in the the DOT MATRIX DISPLAY. To accept this profile, press
ENTER. To view another profile, press an ARROW key. Continue to press the ARROW key until a desired profile appears.
Then, press ENTER to accept the profile.
ENTERING A DURATION
After a workout is selected, the top DATA WINDOW flashes a default workout duration of 30 minutes. Press ENTER to
accept the default. Or, to change the duration, use the ARROW keys. Then, when the desired duration appears in the
DATA WINDOW, press ENTER to accept the duration. It is not possible to change the duration of a workout-in-progress.
13
ENTERING WEIGHT
After a workout is selected, the top DATA WINDOW flashes a default weight. Press ENTER to accept the default. Or, to
change the weight, use the ARROW keys. Then, when the weight appears in the DATA WINDOW, press ENTER to
accept it. The on-board computer calculates the number and rate of calories burned using the entered weight as well as
the pedaling speed.
SELECTING A DIFFICULTY LEVEL
After a duration is entered, the bottom DATA WINDOW flashes a default difficulty level of “1”, which is the easiest of the
nine difficulty levels. Press ENTER to accept the default. Or, to change the level, use the ARROW keys. Then, when the
desired level appears in the DATA WINDOW, press ENTER to accept the duration.
Each of the nine difficulty levels corresponds to a range of resistance levels as seen in the table below. Resistance
levels are applied to each individual interval within a workout profile. See Section 4.3, titled Workout Descriptions for more
information. While the workout is in progress, it is possible to change the resistance level of the current interval. That
change remains in effect for the duration of the interval. See the topic titled Adjusting the Intensity Level in this section.
Difficulty
Level
Resistance
Level Range
1
2
3
4
5
6
7
8
9
1 to 8
2 to 9
3 to 10
4 to 11
5 to 12
6 to 13
7 to 14
8 to 15
9 to 16
STARTING A WORKOUT
After accepting a difficulty level, press START to begin the workout.
ADJUSTING THE RESISTANCE LEVEL OF AN INTERVAL
The cross-trainer features 16 resistance levels, with “1” being the easiest and “16” being the most difficult. While a
workout is in progress, it is possible to change the resistance level of the current interval. To do so, simply press the UP
or DOWN ARROW key repeatedly until the DATA DISPLAY window shows the desired level. That change remains in
effect for the duration of the interval only.
Note: The cross-Trainer features speed-dependent braking resistance. For a set resistance level on the monitor, the
resistance increases with the user’s speed. The computer makes no adjustments to maintain the resistance level based
on the user’s speed.
PAUSING A WORKOUT
To pause a workout-in-progress, press the STOP key, or simply stop pedaling for 25 seconds. A workout can remain in pause
mode for a maximum duration of five minutes. If a paused workout is not resumed before the five-minute pause duration
ends, the console shuts down, and the paused workout information is lost. To resume a paused workout, press the START
key or simply begin pedaling again.
RESETTING A WORKOUT
To reset a workout, press the STOP key, and hold it for three seconds. This deletes the current workout and makes it possible
to set up a new workout.
REVIEWING A COMPLETED WORKOUT
When a workout reaches the end of its duration, the console emits four consecutive beeps. At this point, it is possible to
review summary data for the completed workout, includng total calories burned and distance traveled, by pressing the
SCROLL key and reading the results in the DATA WINDOWS. Afterward, press the STOP key to return to the workout-select
mode.
14
USING THE HEART RATE ZONE TO MAXIMIZE WORKOUT BENEFITS
Research shows that keeping the heart rate within a certain range while exercising promotes muscular and cardiovascular
conditioning for maximum health benefits. This range is between 60 percent and 85 percent of a given user’s theoretical
maximum heart rate. The maximum rate varies by age. To calculate it, subtract the user’s age from the number 220.
For example, the theoretical maximum heart rate for a 35-year-old user would be 185 beats per minute (bpm) because
220-35=185. Therefore, the optimal heart rate range or zone for a 35-year-old user would be between 111 bpm
(185 x .60) and 157 bpm (185 x .85).
NOTE: Consulting a fitness trainer is recommended for defining specific fitness goals and designing a workout program.
To monitor the heart rate during a workout, feel the pulse in the wrist or the carotid artery in the neck while looking at a
watch. Count the number of pulse beats within one minute.
SWITCHING THE CONSOLE DISPLAY TO METRIC UNITS
By default, the cross-trainer’s console displays the workout statistic of distance in English units. It is possible to switch to
metric units. When the console is shut down, remove the four screws that attach the console to the console support
assembly column. Carefully turn the console upside down and flip the “English/Metric” switch that appears in the back of
the console to the “Metric” setting. Re-attach the console to the support assembly column. Restart the cross-trainer.
4.3 WORKOUT DESCRIPTIONS
INTERVAL
This workout combines “hills” and “valleys” of alternating high- and low-resistance levels. Raising and decreasing the
heart rate in this manner is proven to provide effective, time-efficient fitness results. Each interval is of equal duration,
and the overall duration of the workout determines the duration of the intervals. As the profile diagram indicates, the
workout begins with a low-resistance warm-up and ends with a low-resistance cool-down.
RANDOM
When the user selects a RANDOM workout, the cross-trainer computer automatically generates various profiles, each
offering a different combination of resistance levels. This choice of profiles adds variety to the workout routine.
15
MANUAL
MANUAL is a workout in which the resistance level does not change automatically. When a MANUAL workout is in
progress, the user can vary the resistance levels by pressing the UP and DOWN ARROW keys.
PEAK
PEAK is intended to burn fat by maintaining a constant level of resistance throughout the workout. As the profile diagram
indicates, the resistance level begins gradually, maintains a plateau and then gradually declines.
SLOPE
SLOPE gradually increases the intensity throughout the workout duration. It is intended to strengthen the heart, as well
as the major muscle groups that are most active during the workout, such as the leg muscle groups. As the profile dia-
gram indicates, the workout starts at a low resistance level, builds to a peak and and with a low-level cool-down interval.
CHALLENGE
CHALLENGE begins at a high resistance level and maintains this level throughout the duration. As the profile diagram
indicates, the workout begins at a high level and continues for most of the duration at a high plateau.
16
5
SERVICE AND TECHNICAL DATA
5.1 PREVENTATIVE MAINTENANCE TIPS
The cross-trainer is backed by engineering excellence and is one of the most rugged and trouble-free pieces of exercise
equipment on the market today. The manufacturer’s products have proven to be durable in health clubs, colleges, military
facilities, and other locations the world over. This same technology, engineering expertise, and reliability have gone into
the cross-trainer.
NOTE: The safety of the equipment can be maintained only if the equipment is examined regularly for damage or wear.
If maintenance is required, keep the equipment out of use until defective parts are repaired or replaced. Pay special atten-
tion to parts that are subject to wear as outlined in the Preventive Maintenance Schedule.
The following preventive maintenance tips will keep the cross-trainer operating at peak performance:
•
•
•
•
Locate the cross-trainer in a cool, dry place.
Clean the top surface of the pedals regularly.
Keep the display console free of fingerprints and salt build-up caused by sweat.
Use a 100% cotton cloth, lightly moistened with water and mild liquid cleaning product, to clean the cross-train-
er. Other fabrics, including paper towels, may scratch the surface. Do not use ammonia or acid-based clean-
ers.
•
•
Long fingernails may damage or scratch the surface of the console; use the pad of the finger to press the selec-
tion buttons on the console.
Clean the housing thoroughly on a regular basis.
NOTE: A non-abrasive cleaner and soft cotton cloth are strongly recommended for cleaning the exterior of the unit. At no
time should cleaner be applied directly to any part of the equipment; apply the non-abrasive cleaner on a soft cloth, and
then wipe the unit.
5.2 PREVENTATIVE MAINTENANCE SCHEDULE
Follow the schedule below to ensure proper operation of the product.
ITEM
WEEKLY
C
MONTHLY
I
BI-ANNUALLY ANNUALLY
Display Console
Console Mounting Bolts
Frame
I
C
C
I
Plastic Covers
KEY: C=Clean; I=Inspect
I
17
5.3 HOW TO OBTAIN PRODUCT SERVICE
1. Verify the symptom and review the operating instructions. The problem may be unfamiliarity with the product and its
features and workouts.
2. Locate and document the serial number of the unit. The serial number plate is located on the front stabilizer, below
the shroud.
3. Contact Customer Support Services via the Web at: www.lifefitness.com, or call the nearest Customer Support
Services group:
For Product Service within
the United States and Canada:
Telephone: (+1) 847.451.0036
FAX: (+1) 847.288.3702
Toll-free telephone: 800.351.3737
For Product Service Internationally:
Life Fitness Europe GmbH
Telephone: (+49) 089.317.751.66
FAX: (+49) 089.317.751.38
Life Fitness Asia Pacific Ltd
Telephone: (+852) 2891.6677
FAX: (+852) 2575.6001
Life Fitness (UK) LTD
Telephone: (+44) 1353.665507
FAX: (+44) 1353.666018
Life Fitness Latin America
and Caribbean
Telephone: (+1) 847.288.3964
FAX: (+1) 847 288.3886
Life Fitness Atlantic BV
Life Fitness Benelux
Life Fitness Brazil
Telephone: (+32) 03.644.44.88
FAX: (+32) 03.644.24.80
Telephone: (+32) 87.300.942
FAX: (+32) 87.300.943
Telephone: (+55) 11.7295.2217
FAX: (+55) 11.7295.2218
Life Fitness Japan
Telephone: (+81) 3.3359.4306
FAX: (+81) 3.3359.4307
Life Fitness Italia S.R.L.
Telephone: (+39) 0472.835.470
FAX: (+39) 0472.833.150
Life Fitness Iberia
Telephone : (+34) 93 672 4660
FAX : (+34) 93 672 4670
Toll-free telephone: 800.438836
Life Fitness Vertriebs GmbH
Telephone: (+43) 1615.7198
FAX: (+43) 1615.7198.20
18
5.4 CROSS-TRAINER SPECIFICATIONS
Designed use:
Maximum user weight:
Resistance system:
CONSOLE:
Consumer
300 pounds / 136 kilograms
Eddy current
Displays:
DATA DISPLAYS with time, RPM, distance, calories, and level
DOT MATRIX WINDOW indicating workout profile
Summaries:
Time, distance
WORKOUTS:
Intensity levels:
Pedal size
Quck Start Manual Mode, Interval, Random, Manual, Peak, Slope, Challenge
16
16 inches by 7 inches / 41 centimeters by 18 centimeters
Drive type:
Link6
Power requirements:
120V in United States
220V in Europe
240+V in Australia
Blue
Color:
ASSEMBLED DIMENSIONS:
Length
65 inches / 165 centimeters
27 inches / 68 centimeters
62 inches / 157 centimeters
204 pounds / 93 kilograms
Width
Height
Weight
SHIPPING DIMENSIONS:
Length
Width
73 inches / 185 centimeters
28.5 inches / 72.5 centimeters
32 inches / 81 centimeters
244 pounds / 111 kilograms
Height
Weight
19
|