93Xi, 90X Total Body Tr ainer s
As s e mb l y In s t r u c t io n s
IMPORTANT SAFETY INSTRUCTIONS!
ꢀ DO NOT LOCATE THE CROSS-TRAINER OUTDOORS, NEAR SWIMMING POOLS, OR IN AREAS OF HIGH
HUMIDITY.
ꢀ DO NOT OPERATE YOUR CROSS-TRAINER IF IT HAS BEEN DROPPED, DAMAGED, OR EVEN PARTIALLY
IMMERSED IN WATER. IF THIS OCCURS, CONTACT LIFE FITNESS CUSTOMER SUPPORT SERVICES AT
THE NUMBER IN THE OPERATION MANUAL.
ꢀ DO NOT LOCATE THE CROSS-TRAINER ANY CLOSER THAN 30 INCHES (76 CM ) TO A TELEVISION
SET.
ꢀ DO NOT LOCATE ADDITIONAL CROSS-TRAINERS ANY CLOSER THAN 42 INCHES (107 CM) FROM
CENTER TO CENTER TO AVOID INTERFERENCE (CROSS TALK) BETWEEN HEART RATE MONITORS.
ꢀ DO KEEP THE AREA AROUND YOUR CROSS-TRAINER CLEAR OF ANY OBSTRUCTIONS, INCLUDING
WALLS AND FURNITURE. ENSURE THAT THERE IS AT LEAST A 12 INCH (30CM) CLEARANCE IN FRONT
OF THE CROSS-TRAINER.
ꢀ DO VERIFY THE CONTENTS OF THE DELIVERY CARTON AGAINST THE ACCOMPANYING PARTS LIST
PRIOR TO SETTING THE CARTONS AND SHIPPING MATERIAL ASIDE. IF ANY PARTS ARE MISSING,
CONTACT LIFE FITNESS CUSTOMER SUPPORT SERVICES AT THE NUMBER LISTED IN THE OPERATION
MANUAL. SAVE THE SHIPPING CARTONS IN CASE OF RETURN.
ꢀ DO READ THE ENTIRE OPERATION MANUAL PRIOR TO ATTEMPTING TO OPERATE THIS MACHINE AS
THIS IS ESSENTIAL FOR PROPER USE.
CONSIGNES DE SECURITE IMPORTANTES!
ꢀ NE PLACEZ PAS L'APPAREIL À L'EXTÉRIEUR, PRÈS D'UNE PISCINE OU DANS UN ENDROIT TRÈS
HUMIDE
ꢀ NE FAITES PAS FONCTIONNER L'APPAREIL S'IL EST TOMBÉ, S'IL A ÉTÉ ENDOMMAGÉ OU S'IL A ÉTÉ
ꢀ PARTIELLEMENT PLONGÉ DANS L'EAU. SI CELA S'EST PRODUIT, CONTACTEZ LE SERVICE APRÈS-VENTE
DE LIFE FITNESS AU NUMÉRO FOURNI DANS LE MANUEL D'UTILISATION
ꢀ NE PLACEZ PAS L'APPAREIL À MOINS DE 76 CM D'UN POSTE DE TÉLÉVISION
ꢀ NE PLACEZ PAS D'AUTRES APPAREILS DU MÊME TYPE À PROXIMITÉ. UN ESPACE D'AU MOINS 107 CM
DOIT ÊTRE OBSERVÉ ENTRE LES PARTIES CENTRALES DE DEUX APPAREILS AFIN D'ÉVITER LES
INTERFÉRENCES ENTRE LES CONTRÔLEURS DE RYTHME CARDIAQUE.
ꢀ MAINTENEZ LA ZONE AUTOUR DE L'APPAREIL LIBRE DE TOUTE OBSTRUCTION, Y COMPRIS MURS ET
MEUBLES. VEILLEZ À LAISSER UN DÉGAGEMENT D'AU MOINS 30 CM DEVANT L'APPAREIL
ꢀ VÉRIFIEZ SI L'EMBALLAGE CONTIENT TOUTES LES PIÈCES DE LA LISTE JOINTE AVANT DE LE METTRE
DE CÔTÉ. SI DES PIÈCES SONT ABSENTES, CONTACTEZ LE SERVICE APRÈS-VENTE DE LIFE FITNESS
AU NUMÉRO INDIQUÉ DANS LE MANUEL D'UTILISATION. CONSERVEZ L'EMBALLAGE AU CAS OÙ VOUS
DEVRIEZ RENVOYER L'APPAREIL.
ꢀ LISEZ LE MANUEL DE L'UTILISATEUR TOUT ENTIER AVANT D'ESSAYER DE FAIRE FONCTIONNER CET
APPAREIL. CECI EST INDISPENSABLE À SON UTILISATION CORRECTE.
TOOLS REQUIRED FOR ASSEMBLY...
Magnetic #2 Bit Phillips Screwdriver, T-45 Hex Key Wrench, 16mm Open End Wrench
PARTS DESCRIPTION
1
3
Torx Socket Head Screw
M8 – 1.25 x 19
0017-00101-1791
Phillips Pan Head Screw
M4.2 – 0.70 x 10
Qty: 12
2
Phillips Pan Head Screw
M4 – 0.70 x 19
0017-00101-1796
Qty: 14
Qty: 1
Qty: 2
4
Console Assembly
0017-00101-1846
5
Front Rocker Cover
OK62-01009-0000
Console Support Assembly
AK62-00123-0000
Front Pivot Arm Cover
OK62-01012-0000
Left User Arm Assembly
AK62-00091-0000
Left Bullhorn Cover
OK62-01008-0001
Accessory Tray
OK62-01022-0000
Base Frame Cap
OK62-01004-0000
Cap: Console Support
OK62-01030-0000
Qty: 2
Qty: 1
Qty: 2
Qty: 1
Qty: 1
Qty: 1
Qty: 1
Qty: 1
6
Left Back Rocker Cover
OK62-01011-0000
Console Support Cover
OK62-01023-0000
Rear Pivot Arm Cover
OK62-01013-0000
Right User Arm Assembly
AK62-00090-0000
Right Bullhorn Cover
OK62-01007-0001
Right Back Rocker Cover
OK62-01010-0000
Foot Cover
Qty: 1
Qty: 1
Qty: 2
Qty: 1
Qty: 1
Qty: 1
Qty: 4
Qty: 2
7
8
9
10
12
16
18
20
22
11
15
17
19
21
OK62-01003-0000
Phillips Pan Head Screw
M4 – 0.70 x 44
0017-00101-1854
1
3
2
22
1”
2”
3”
4”
5”
This product is preconfigured to accept the addition of the Life Fitness Entertainment System. A POWER CABLE and
COAXIAL CABLE have been pre-installed. Please read both the product assembly instructions and Entertainment Ready
assembly instructions (included with the Life Fitness Entertainment System) prior to assembly.
Route the POWER CABLE and COAXIAL CABLE alongside the MAIN WIRE HARNESS where applicable.
IMPORTANT!
DO NOT DISCARD THE SHIP KIT LOCATED ON TOP OF THE PEDAL LEVERS. ALL NECESSARY COMPONENTS NEEDED
TO COMPLETE THE INSTALLATION ARE LOCATED IN THE SHIP KIT.
IMPORTANT!
NE JETEZ PAS LE KIT PLACÉ SUR LE DESSUS DES LEVIERS DE PÉDALE. IL CONTIENT TOUS LES ÉLÉMENTS
NÉCESSAIRES POUR L'INSTALLATION.
1. Locate the LEFT HANDLEBAR (11). Position the HANDLEBAR near the top
of the LEFT PIVOT ARM (A).
Align the mounting holes of the LEFT HANDLEBAR with the mounting holes
at the top of the LEFT PIVOT ARM. Secure them together using three
SCREWS (1).
11
9
2. Locate one LEFT FRONT ROCKER COVER (5) and the LEFT BACK
ROCKER COVER (6). Position the LEFT BACK ROCKER COVER over the
user side of the ROCKER ARM making sure that it seats fully over the
BULLHORN MOUNTING BRACKET (D). Place the FRONT ROCKER
COVER over the opposite side of the ROCKER ARM in the same manner.
Secure the COVERS using two PHILLIPS PAN HEAD SCREWS (2). Tighten
2
the SCREWS securely. Do not over-tighten the SCREWS.
1
3. Locate one FRONT PIVOT ARM COVER (9) and one BACK PIVOT ARM
10
A
COVER (10). Position the BACK PIVOT ARM COVER over the user side of
the ROCKER ARM making sure that it interlocks with the ROCKER COVER.
Place the FRONT PIVOT ARM COVER over the opposite side of the PIVOT
ARM in the same manner. Secure the COVERS using two PHILLIPS PAN
HEAD SCREWS (2). Tighten the SCREWS securely. Do not over-tighten the
SCREWS.
5
4. Remove the LEFT BULLHORN (B) from the BULLHORN MOUNTING
BRACKET (D) by removing the two SCREWS (C). The shipping installation is
upside-down from its final installed location. Rotate the LEFT BULLHORN so
the hand grip faces upwards and reinstall the LEFT BULLHORN using the two
previously removed SCREWS.
D
NOTE: IF THE ENTERTAINMENT OPTION WILL NOT BE USED,
CAREFULLY GATHER THE COAXIAL CABLE (P) AND POWER CORD
(Q) AND INSERT THEM INTO THE CONSOLE SUPPORT ASSEMBLY (7)
5. Repeat steps one through four to install the RIGHT ROCKER COVERS (5 &
6), PIVOT ARM COVERS (9 & 10), BULLHORN (14) and BULLHORN
COVER (16).
A
E
NOTE: THE RIGHT PIVOT ARM COVERS ARE REVERSED FRONT AND
BACK. THE SCREWS WILL BE INSTALLED FROM THE REAR.
6
2
6. Unwrap the WIRE HARNESS (F,G,P,Q) leading from the MONOCOLUMN
(H). Feed the WIRE HARNESSES through the CONSOLE SUPPORT
ASSEMBLY TUBE (I) located at the top and front of the MONOCOLUMN.
Locate the CONSOLE SUPPORT ASSEMBLY (7) and position it near the top
of the MONOCOLUMN. Feed the WIRE HARNESSES through the
CONSOLE SUPPORT ASSEMBLY as shown. Align the bottom mounting
holes of the CONSOLE SUPPORT ASSEMBLY with those in the CONSOLE
SUPPORT ASSEMBLY TUBE. Secure them together using six SCREWS (1).
Tighten the SCREWS securely.
B
C
15 22
P
Q
G
F
NOTE: BE CAREFUL NOT TO DAMAGE THE WIRE HARNESSES (E & F)
WHEN ROUTING IT THROUGH THE CONSOLE SUPPORT ASSEMBLY
OR WHEN MOUNTING THE CONSOLE SUPPORT ASSEMBLY TO THE
CONSOLE SUPPORT ASSEMBLY TUBE.
2
7
21
4
7. Locate the ACCESSORY TRAY (17). Slide the ACCESSORY TRAY into the
top of the MONOCOLUMN (H) as shown. Be sure the ACCESSORY TRAY is
fully seated.
17
1
NOTE: BE CAREFUL NOT TO DAMAGE THE MAIN WIRE HARNESS
WHEN SLIDING THE ACCESSORY TRAY INTO THE MONOCOLUMN.
2
Secure the accessory tray to the CONSOLE SUPPORT ASSEMBLY using
two SCREWS (3). Tighten the SCREWS securely. Do not over-tighten the
SCREWS.
1
8
3
I
H
8. Locate the DISPLAY CONSOLE (4). Position the CONSOLE near the top of
the CONSOLE BRACKET. Attach all CONNECTORS (F & G) leading from
the CONSOLE BRACKET to their corresponding CONNECTORS in the
back of the DISPLAY CONSOLE. Feed any excess WIRE HARNESS into
the CONSOLE BRACKET and place the DISPLAY CONSOLE onto the
CONSOLE BRACKET aligning the mounting holes. Secure the DISPLAY
CONSOLE using four SCREWS (2). Tighten the SCREWS securely. Do not
over-tighten the SCREWS.
P
Q
G
F
2
7
21
4
9. Locate the CONSOLE SUPPORT COVER (8). Position the CONSOLE
BRACKET COVER over the underside of the CONSOLE SUPPORT
ASSEMBLY (7) as shown and secure it using two SCREWS (2). Tighten the
SCREWS securely. Do not over-tighten the SCREWS.
17
1
10. Locate the CONSOLE SUPPORT CAP (21). Snap the CAP into position at
the top of the CONSOLE SUPPORT COVER.
2
1
11. Locate the BASE FRAME CAP (19). Remove the two SCREWS (J)
securing the front of the BASE FRAME COVER (K) to the BASE FRAME
(L). Position the CAP over the front of the BASE FRAME as shown sliding
the mounting tabs to the inside of the BASE FRAME COVER. Secure the
CAP using two SCREWS (J) previously removed. Tighten THE SCREWS
securely. Do not over-tighten the SCREWS.
8
3
I
12. Locate the four FOOT COVERS (20). Align the COVERS with the ends of
the STABILIZER BARS (M). Insert the post on the underside of the FOOT
COVERS into the mounting holes on the top of each STABILIZER. Press
the FOOT COVERS firmly into position.
13. Position the unit into the desired location for use. Properly level the unit
H
according to the instructions in the Operation Manual.
J
19
L
20
M
K
Physical Dimensions:
93Xi / 90X
Length
Width
84.75 inches / 215 centimeters
26.5 inches / 67 centimeters
64 inches / 162.6 centimeters
286 pounds / 130 kilograms
Height
Weight
PRE-OPERATION CHECKLIST
ꢁ
ꢁ
Ensure that all fasteners are tight.
Make sure the CROSS-TRAINER is properly leveled and stable.
(Refer to the Operation Manual)
ꢁ
ꢁ
Ensure that the Leveler Jam Nuts are tight.
(Refer to the Operation Manual)
Read the entire Operation manual before using the Cross-Trainer.
LISTE DES VÉRIFICATIONS À EFFECTUER AVANT LA MISE EN MARCHE
ꢁ
ꢁ
Vérifiez si tous les dispositifs de fixation sont serrés
Vérifiez si l'APPAREIL D'EXERCICE POLYVALENT est de niveau et stable.
(Référez-vous au manuel d'utilisation.)
ꢁ
ꢁ
Vérifiez si les contre-écrous des vérins de mise à niveau sont serrés.
(Référez-vous au manuel d'utilisation.)
Lisez le manuel d'utilisation dans son intégralité avant d'utiliser l'appareil d'exercice polyvalent..
Before attempting to operate your Total Body Trainer, it is imperative that you familiarize yourself with the contents of
the Operation Manual. If your Total Body Trainer does not respond as described in the Operation Manual, contact the
nearest Life Fitness service center as listed in the Operation Manual.
Life Fitness Customer Support Services
(800) 351-3737 or (847) 451-0036
Prior to your call, please be sure you have located and noted the
MODEL NUMBER & SERIAL NUMBER.
The Model & Serial number information of your Life Fitness Total Body Trainer is listed on a label
located on the rear stabilizer.
©2006 Life Fitness, a division of Brunswick Corporation. All rights reserved. Life Fitness, Lifepulse, FlexDeck and Smart Stop are
trademarks of Brunswick Corporation.
MO51-00K62-A177
10.06
|