Specifications
ART200A
System:
Voice Equalization:
+4.0 dB @ 3kHz
Active Speaker System
Freq. Range (–10 dB):
50Hz-19kHz
+4.0 dB @ 6kHz
Quick-Start Guide
The ART200A is a full-range two-way
professional active speaker system that
combines high power and wide bandwidth in
a light-weight enclosure for fixed-installation
systems. The 12" low-frequency transducer, in
combination with a 1" compression driver
coupled to an integral 90˚ x 70˚ constant
directivity polynomial horn, form an extremely
powerful package for any small to medium-
sized sound reinforcement application.
It features a balanced XLR input with a
Mic/Line switch and a paralleled balanced
XLR output for cascading multiple speakers.
Rear panel controls also include Music and
Voice equalization switches, a rotary volume
control, and an input limiter.
The two built-in power amplifiers provide
120W for the LF driver and 40W for the HF
driver. The enclosure is constructed of high-
strength polypropylene, with M10 threaded
inserts on all four sides for rigging, and an
integral locking 1-3/8" socket in the bottom
for mounting on a standard speaker stand.
Indicators:
Freq. Response ( 3 dB):
70Hz-17kHz
Power ON, Limiter
Amplifiers:
Horz. Coverage Angle (–6 dB):
LF Amplifier Power:
90°, averaged 1kHz-10kHz
120 watts RMS
Vert. Coverage Angle (–6 dB):
HF Amplifier Power:
70°, averaged 1kHz-10kHz
Directivity Factor Q (DI):
40 watts RMS
Distortion:
9.5 (9.8), averaged 1kHz-10kHz
< 0.1% THD at rated power
System Sensitivity:
Amp Protection:
101 dB, 1W@1m
Rated Maximum SPL:
Thermal, limiter, short circuit
Power Supply:
122 dB @ 1 m (3.3 ft) peak
115/230 VAC, 2A, 50/60 Hz
HF Protection:
Dynamic
Physical:
Enclosure:
Transducers:
Asymmetrical trapezoidal,
reinforced polypropylene
Low Frequency:
12" (300 mm) diameter woofer
Mounting:
High Frequency:
Lockable 1-3/8" (35mm) stand
mount
1" (25 mm) compression driver,
horn loaded
Safety First!
Before connecting and using the
Rigging Inserts:
4 points, accepts M10 threaded
1. Never install, connect, or disconnect
the unit with the power supply on.
equipment, please read this Quick-Start Guide
carefully and keep it for future reference.
hardware
Preamp and Processor:
Input/Output Connectors:
2 XLR balanced
2. Before powering up the speaker,
make sure the voltage select switch
corresponds to the AC Voltage supply.
Input Sensitivity:
Mic In:
Line In:
8mV
125mV
WARNING! This equipment has been
designed to be installed by qualified
Dimensions HxWxD:
professionals only! There are many factors to
be considered when installing professional
sound reinforcement systems, including
mechanical and electrical considerations, as
well as acoustic coverage and performance.
Mackie Industrial strongly recommends that
this equipment be installed only by a
24.4" x 15.4" x 12.3"
(620 mm x 390 mm x 312 mm)
Input Impedance:
Mic In:
3. Make sure the safety ground on the
power cord is properly grounded.
650Ω unbalanced
1.3kΩ balanced
Net Weight:
4. To prevent the risk of electric shock,
never open the unit. There are no
user serviceable parts inside.
39.7 lb (18.0 kg)
Line In:
10kΩ unbalanced
19kΩ balanced
Crossover Frequency and Slope:
1.8kHz; 24 dB/octave
5. To ensure normal cooling of the
amplifier, make sure the unit is well-
ventilated. Avoid exposure to direct
sunlight or proximity to any heat
source, dust, or dampness.
professional sound installer or contractor.
Time Alignment:
16220 Wood-Red Road NE Woodinville, WA 98072
TEL +888.337.7404, FAX +425.487.4337
Analog, 0.3 ms HF delay
Speaker Protection:
CAUTION: To avoid the risk of electric
shock, never allow this equipment to
be exposed to rain or dampness.
Thermal, over-excursion
Music Equalization:
+4.3 dB @ 65Hz
+4.0 dB @ 12kHz
Part No. 910-161-20 Rev. A 2/00
© 2000 Mackie Industrial. All Rights Reserved. Printed in the USA.
|