OWNER’S MANUAL
™
Gourmet Series Marine Gas Grill
Model A10-1225
For questions regarding performance, assembly,
operation, parts, or returns, contact the experts
at MAGMA by calling TOLL FREE IN U.S.A. AND
CANADA 1-800-86-MAGMA
7:00 a.m. - 5:00 p.m. Pacific Time Monday thru
Friday or e-mail us at [email protected]
Read all instructions before operating. Save manual for future reference.
MOUNT HARDWARE
Fasteners are supplied for both Single Mount and Dual Mount grill mounting
options. See Magma Catalog or Website for best mount selection.
Single mount through-bolt
applications
4 Carriage bolts & lock nuts.
Dual mount applications
4 Carriage bolts & lock nuts. Only 4 bolts
required for grill mounting. Place bolts (2 per
side) diagonally from each other as shown.
Single mount non-through-bolt
applications, including Style 1 “Levelock”
4 Hex head bolts & lock washers.
Carriage bolt
& lock nut
Hex head bolt
& lock washer
ON-BOARD FUEL SYSTEMS APPLICATION
•For on-board LPG (Propane) Systems, use Magma Type 3-High Output-
Low Pressure LPG Control Valve and Magma Low Pressure LPG Hose Kit.
•For on-board CNG (Natural Gas) Systems, use Magma Type 4-High Output-
Low Pressure Natural Gas Control Valve.
See Magma website for
replacement part numbers
and valve applications.
Thermometer
Lid Lock
Warming Rack
Grill Grates
Burner
Radiant Plate
Liner
Outer Shell
Match Light
Hole
Valve Chamber
Control Valve Regulator
Type 1 High-
Output Shown
Mount
Support Pad
Slide Out
Grease Tray
Piezo Igniter
3
OPERATING PROCEDURES
OPERATE ONLY ON “LOW” WHEN LID IS CLOSED.
ALWAYS OPERATE WITH GREASE TRAY IN PLACE.
WARNING: Do not overheat grill. Magma Grills do not require pre-heating.
Stainless Steel loses anti-corrosive characteristics when subjected to extreme
heat. Most grilling is done on low temperature with the lid closed. If medium
or high heat is required, grill with lid open.
LIGHTING INSTRUCTIONS
• Open lid during lighting.
• Depress knob and rotate counter-clockwise to the “HIGH” flame
• Push Piezo Igniter.
position.
• Visually confirm ignition through match light hole.
• Turn knob to adjust flame.
• If grill does not light, repeat process.
MATCH LIGHTING INSTRUCTIONS
• Open lid during lighting.
• Depress knob and rotate counter-clockwise to the “HIGH” flame
• Hold match or gas flame long lighter up to the match light hole.
• Visually confirm ignition through match light hole.
position.
TO REDUCE FLARE-UP
• Empty and clean grease tray prior to each use.
• Trim excess fats from meat.
• Use non-oil based marinades.
• Reduce heat.
• Use water spray directly on flare-ups.
NOTE: Before lighting, lid lock must be positioned not to engage. Open lid
and turn lock to locked position, or bring lock latch up to handle in open
position and flip lock actuator back onto handle.
PRACTICAL HINTS:
Before lighting your grill, be sure that …
•
•
•
•
•
•
Grill is secure and properly mounted.
Internal components and grease tray are clean and correctly positioned.
You have plenty of gas in the canister.
Gas canister is attached properly and there are no gas leaks.
Lid lock has been set not to engage.
You have a water spray bottle handy to cool a hot grill or stop any flare-ups.
STOWING TIPS
• Always disconnect the fuel canister from the valve prior to stowing.
• Stow the valve in a clean, dry area to protect from corrosion to valve.
•
Always store propane in a sealed propane storage locker that allows leakage
to vent overboard or use Magma A10-210 Propane Storage Tote.
Never stow below decks
4
ELECTRODE SPARK ADJUSTMENT
CAUTION: Spark can cause small shock. Do not leave
fingers on or near electrode wire while engaging igniter.
• Electrode wire should be approximately 1/8” from gas
exit hole in burner. Carefully adjust wire if required.
A
DISASSEMBLY & RE-ASSEMBLY
Lift radiant plate up & out of left slot (see B) and remove by sliding it out
of right slot (see C).
•
•
Remove burner screw (see B) and remove burner. Check burner for grease
residue or spider webs that may obstruct gas flow. CAUTION: WHEN
REPLACING BURNER, CUT SLOT IN BURNER MUST FACE DOWN.
To remove liner from outer shell you must disconnect the electrode wire
(see D). First remove the two screws on valve chamber (see D) and remove
the cover plate. Gently pull wire off connector (see D). It is not necessary to
remove electrode from liner.
Remove Lid and liner by removing hinge screws and lock nuts with 3/16”
hex key wrench (supplied) and 1/2” wrench or pliers. CAUTION: LOCK NUTS
MUST BE INSTALLED WITH LOCKING INDENT MARKS SHOWING (see E).
IMPROPER INSTALLATION WILL DAMAGE THE HINGE SCREW AND LOCK NUT.
Lift liner out of outer shell by lifting up on liner lip on back side of liner
(see F). When replacing liner, be sure top lip of liner installs over top edge
of outer shell (start with corners of lip and work in).
•
•
•
• Inspect burner, remove any obstructions.
• Clean as indicated in Maintenance (page 6).
• To re-assemble, reverse the procedure.
Disconnect wire
B
D
C
Right
side
slot
Left
side
slot
Electrode
Screws
Burner screw
F
E
Liner Lip
Liner
Outer Shell
Locking
Indents
5
MAINTENANCE
About Stainless Steel - Stainless steel exposed to prolonged periods of high heat will change
color and texture. Magma grills require no preheating. Not preheating will keep your grill cooler
and greatly extend the life and beauty of your grill. Texture and color change is normal on
interior components and will not affect the product’s operation or performance.
Exterior Stainless Steel Components - Cleaning the exterior surface after every use will help
prevent discoloration. Use soapy water with a soft cloth or sponge. Rinse thoroughly with fresh
water and dry. We recommend covering the grill between uses. Optional covers are available
from Magma retailers or direct from Magma. CAUTION: ABRASIVE PADS OR CLEANERS WILL
DAMAGE THE FINISH.
Interior Components - Remove heavy residue from grill and empty grease tray between
each use. We recommend complete disassembly and cleaning at least once a year depending
on amount of use (see page 5) and always prior to long term storage. For burnt-on residue we
recommend Easy-Off brand Oven & Grill Cleaner. If cleaner is used on liner or lid, complete
disassembly is recommended to remove any cleaner residue left between components. Wash
all components with soapy water after using cleaner. CAUTION: AVOID CONTACT OF IGNITER
AND ELECTRODE WIRE AND WIRE CONNECTORS WITH OVEN CLEANER.
Grill Grates - Clean with brass wire brush while grill is warm. Use Oven & Grill cleaner for
burnt-on residue. Wash with soapy water and dry prior to storage.
Ceramic Electrode - Located just beside the burner, it should be kept clean of grease and
debris. Be careful not to damage the ceramic insulation or bend the wire. See page 5 for
electrode spark adjustment.
Control Valve - All valves are set and tested at our factory. Do not attempt to adjust or
disassemble the valve in any way. Call Magma if you suspect it is not adjusted properly. Clean
valve with a cloth and remove any debris obstructing the gas outlet orifice using a pin or needle.
Repair/Replacement Parts - See Magma’s Website for a complete list of Repair or
Replacement Parts. www.MagmaProducts.com
USING GRILL WITH ON-BOARD LPG (PROPANE) SYSTEMS
• Magma On-Board LPG (Propane) Valves
and Hose Kits allow Magma Grills to be
installed within a boats existing on-board,
pre-regulated low pressure LPG (Propane)
system.
Gourmet
Gas Grill
Gourmet
Gas Grill
Type 3
Valve
Align valve stem key
to valve chamber
lock detent and rotate
• Use only Magma Type 3 Low
Pressure LPG (Propane) Valves. See
our Valve Application Guide at www.
MagmaProducts.com for correct valve.
• In North America use Magma A10-225
LPG 10' Hose Kit in conjunction with
Type 3 Valve. Outside North America check
your local dealer for proper hose and fittings.
• A primary shutoff valve (supplied with
A10-225 hose kit) must be used with this
control valve at point of connection into
your system. This allows shut off of gas
supply to hose leading to grill.
Gourmet
Gas Grill
Type 3
Valve
Typical Marine &
R.V. Application
Cylinder Valve
Gauge
Solenoid
Shut off
valve
To other LPG
appliance
or use cap
Gas Regulator
Propane (LPG)
A10-225
Hose Kit
6
TROUBLE SHOOTING GUIDE
Problem
Possible Cause
Possible Solution
Burner will not
light with igniter
Igniter electrode covered with
grease or residue
Clean igniter electrode
Igniter/electrode too far from
burner
Adjust electrode until proper
spark appears (see page 5)
Igniter/electrode wire loose or
disconnected
Reconnect wire between
igniter & electrode (see page 5)
Wire is shorted causing spark
from wire before electrode
Call Magma
No spark being generated
No gas flow
Call Magma
Burner will not
light even with
match
Check fuel level, refill cylinder
or replace canister
Obstructed gas flow/debris or
spider webs in burner tube
Clean valve orifice and burner,
check all lines (see page 6)
Flare-up
Excessive cooking temperature
Operate only on low when
lid is closed
Reduce flame level
Leave lid open
Use water spray to cool
Grease and/or residue build-up
Excessive fat in meats
Clean components
Trim fat from cuts of meat
before grilling
Excessive oils in marinades
Use non-oil based marinades
Yellow sooty flame
Blow-out
Obstructed gas flow/debris or
spider webs in burner tube
Check and clean valve orifice
and burner (see page 6)
Flame too low
Increase flame
Wind directly on burner
Obstructed gas flow
Block wind when opening lid
Clean burner or valve orifice
(see page 6)
7
Contents
A
x 4
x 4
B
C
A) (1) 3/16” Hex key wrench for lid removel.
B) Pack of (4) 1/4”-20 x 5/8” hex head screws
and internal lock washers for “Levelock” single
mount application.
x 4
x 4
C) Pack of (4) 1/4”-20 x 5/8” carriage bolts and
lock nuts for dual mount and single mount
applications and table legs.
LIMITED WARRANTY
Magma Products, Inc. guarantees this gas grill to be free from defects in materials or workmanship to the original consumer. This guarantee is for the periods
herein specified when used under normal and reasonable conditions, one (l) year from the date of original purchase. This warranty does not include the cost of
property damage or any inconvenience due to the failure of the product. Nor does it cover damage due to misuse, abuse, accident, or damage resulting from
transportation of the product. Nor does it include damage resulting from the commercial use of this product. If the product fails to operate due to a defect in
materials or workmanship during the warranty period, the defective part will be repaired or replaced at Magma's option. If you wish to obtain performance under
this limited warranty, you should contact Magma's Customer Service Department via telephone at 562-627-0500 or 800-86-MAGMA, or via e-mail at
[email protected], or via U.S. Postal Service mail at “Magma Products, Inc., attention Customer Service, 3940 Pixie Ave. Lakewood, CA, 90712.“ The defective
part, along with proof of purchase, must be returned postage prepaid to Magma Products, Inc. We suggest that you keep your purchase receipt as we may require
reasonable proof of purchase.
In the state of California only, if refinishing or replacement of the product is not commercially practicable, the retailer selling the product, or Magma Products,
Inc., will refund the purchase price paid for the product, less the amount directly attributable to use by the original consumer prior to the discovery of the
nonconformity. In addition, in the state of California only, you may take the product to the retail establishment from which it was purchased or to any retail
establishment selling this product in order to obtain performance under this warranty.
All implied warranties, including the implied warranties of merchantability and fitness for a particular purpose, are limited in duration to the express warranty
periods specified herein for the parts described herein.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Neither Magma dealers, nor the
retail establishment selling this product has any authority to make any warranties or to promise remedies in addition to or inconsistent with those stated above.
Magma's maximum liability shall not exceed the purchase price of the product paid by the original consumer. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusions may not apply to you. The warranty gives you specific legal rights and you may also have
other rights which vary from state to state.
MAGMA and the Magma logo are registered trademarks of Magma Products, Inc.
Monterey is a trademark of Magma Products, Inc.
Patent pending.
CALIFORNIA PROPOSITION 65 – WARNING – The burning of gas cooking fuel generates some by-products, which are on the list of substances,
which are known by the State of California to cause cancer or reproductive harm. California law requires businesses to warn customers of
potential exposure to such substances. To minimize exposure to these substances, always operate this unit according to the use and care
manual, ensuring you provide good ventilation when cooking with gas.
Magma Products, Inc.
3940 Pixie Avenue, Lakewood, CA 90712 • USA
Phone (562) 627-0500 • e-mail: [email protected]
|