ENGLISH
SPECIFICATIONS
OWNER'S
MANUAL
AC Power Input:
AC Power Consumption:
Chassis Construction:
Picture Tube: 25" (measured diagonally)
Audio Power Output Rating:
1.5 Watts
120V, 60Hz
115 Watts
IC Solid state
Receiving Channels:
VHF
UHF
CATV
2-6
14-69
01-97 (5A)-(A-3)
98-99 (A-2)-(A-1)
14-22 (A)-(I)
25" COLOR TELEVISION
Speaker:
Tuner Type:
1.5" x 2.7" Full Range, 8 ohm
181 Channel, Quartz PLL
Frequency Synthesized
23-36 (J)-(W)
37-65 (AA)-(FFF)
66-125 (GGG)-(125)
MT2251
Remote Control: Infrared, Direct Access,
2 x AAA batteries
Antenna Input Impedance:
75 Ohm (VHF/UHF/CATV)
Coaxial Input
CAUTION
Changes or modifications not expressly approved by the party responsible for
compliance with the FCC Rules could void the user's authority to operate this
equipment,
Dimensions:
24 1/3" (W) x 19 2/3" (D) x 20 2/3" (H)
59.9 Ibs
ATTENTION
Weight:
For your protection in the event of theft or loss of loss of this product, please fill in
the information listed below which is for your own personal records.
Date of Purchase
Serial No.
Place of Pufchase
:
:
:
ACCESSORIES
Remote Control
TV/CATV MODE SELECTION
When shipped from the factory, the TV/CATV menu option is set to the "CATV"
(Cable Television) mode. If not using CATV, set this menu option to "TV " mode.
FEATURES
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE PLEASE CALL:
Quartz PLL Frequency Synthesized Tuning System - Electronically locks in and
memorizes available channels for perfect reception.
1-800-919-3647
181 Channel Tuner - The tuning system is capable of receiving all 68 VHF/UHF
standard broadcast channels that are available in your area. When operating on a cable
system, it can tune to the standard VHF channel frequencies plus up to 113 cable
channel frequencies. The actual number of channels received depends upon channel
reception in your area or your cable system.
On-Screen 3 Language Display - Consists of channel, sleep timer, volume level,
muting, text/caption indicators and picture control adjustments. These can be displayed
in English, Spanish or French.
FOR CUSTOMER SERVICE PLEASE CALL OR WRITE TO:
Memcorp Warranty Service
1200 E. Broadway
Princeton, Indiana 47670
(812)386-3200
Picture Adjustments Using The Remote Control - The On-Screen display allows
precise remote control adjustment of BRIGHTNESS, COLOR, CONTRAST,
SHARPNESS and TINT.
Sleep Timer - Operable from the remote control, this TV can be programmed up to 120
minutes to turn off automatically.
Memory Back Up - This system prevents loss of memorized channel selections in case
a power interruption should occur.
V-Chip - The V-Chip function can rate a TV program or a movie content. It allows you to
set a restriction level.
Closed Captioned Decoder - Displays text captions or 1/3 of full screen text on the
screen for hearing impaired viewers.
3I00101A K
99/05
Printed in Thailand
ANTENNA/CATV CONNECTIONS
Combination VHF/UHF Antenna (Single 75 ohm
cable or 300 ohm twin-lead wire)
Connect the 75 ohm cable from a combination VHF/UHF
antenna to the antenna jack.
If your combination antenna has a 300 ohm twin-lead wire,
use the 300-75 ohm matching transformer (not supplied).
Combination VHF/UHF Antenna
Single 75 ohm cable
Combination VHF/UHF Antenna (Separate VHF
and UHF 300 ohm twin-leads)
Connect the UHF twin-lead wire to a combiner (not supplied).
Connect the VHF twin-lead to the 300-75 ohm matching
transformer (not supplied). Attach the transformer to the
combiner. Attach the combiner to the antenna jack.
300 ohm twin-lead wire
Splitter
Separate VHF/UHF Antennas
Connect the 75 ohm cable from the VHF antenna and the
UHF antenna twin-lead to a combiner (not supplied). Attach
the combiner to the antenna jack.
NOTE:If your VHF antenna has a twin-lead wire, use the
300-75 ohm matching transformer (not supplied), then
connect the transformer to the combiner.
300-75 Ohm Matching
Transformer
(not supplied)
Take off the Splitter
UHF Antenna
300 ohm twin-lead wire
For Subscribers of Basic Cable TV Service
VHF Antenna
For basic cable service not requiring a converter/
descrambler box, connect the CATV 75 ohm coaxial cable
directly to the antenna jack on the back of the television.
Single 75 ohm cable
For Subscribers of Scrambled Cable TV Service
If you subscribe to a cable service which requires the use of
a converter/descrambler box, connect the incoming cable to
the converter/descrambler box and connect the output of
the box to the antenna jack on the back of the television.
Follow the connections shown left. Set the television to the
output of the converter/descrambler box (usually channel 3 or
4) and use the converter/descrambler box to select
channels.
300 ohm twin-lead wire
Combiner
(not supplied)
300-75 Ohm matching
transformer
Incoming CATV
(not supplied)
For Subscribers of Unscrambled Basic Cable
with Scrambled Premium Channels
Converter/Descrambler
This television has an extended tuning range and
can tune most cable channels without using a cable
company supplied converter box. Some cable
companies offer "premium pay channels" in which
If you subscribe to a cable service in which basic cable
channels are unscrambled and premium channels require
the use of a converter/descrambler box, you may wish to
Converter/Descrambler
A/B Switch
the signal is scrambled. Descrambling these signals use a two-set signal splitter (sometimes called a "two-set
A
Splitter
B
for normal viewing requires the use of a descrambler
device which is generally provided by the cable
company.
coupler") and an A/B switch box from the cable installer or
an electronics supply store. Follow the connections shown
on left. With the switch in the "B" position, you can directly
tune any nonscrambled channels on your TV. With the
switch in the "A" position, tune your TV to the output of the
converter/descrambler box (usually channel 3 or 4) and use
the box to tune scrambled channels.
3I0-0101A E
2
1/1/32, 09:50
LOCATION OF CONTROLS
CLOSED CAPTION
WHAT IS CLOSED CAPTIONING?
This television has the capability to decode and display Closed Captioned television programs.
Closed Captioning will display text on the screen for hearing impaired viewers or it will translate
and display text in another language.
CLOSED CAPTIONING WITH A VCR
Closed Captioned programs can be recorded and played back on a VCR with the Closed
Captioned text intact. The Closed Captioned text will disappear during Cue (Fast Forward
Search), Review (Rewind Search) and Pause Modes or if the VCR tracking is not adjusted
properly.
Captions: This Closed Caption Mode will display text on the screen in English or another
language (depending on the setting of the Closed Captions CH. 1/2 button). Generally, Closed
Captions in English are transmitted on Captions Channel 1 and Closed Captions in other
languages are transmitted on Captions Channel 2.
1 2
3
4
Text: The Text Closed Caption Mode will usually fill 1/3 of full screen with a programming
schedule or other information. After selecting a Closed Caption Mode, it will stay in effect until
it is changed, even if the channel is changed. If the Captions signal is lost due to a commercial
or a break in the signal, the Captions will reappear when the signal is received again. If the
channels are changed, the Captions will be delayed approximately 10 seconds.
The Captions will appear in places on the screen where they will least interfere with the picture,
usually on the bottom of the screen. News programs will usually show three-line Closed
Captions which scroll onto the screen. Most other shows provide two or three lined Captions
placed near the character who is speaking so the viewer can follow the dialogue.
Words in italics or underlined describe titles, words in foreign languages or words requiring
emphasis. Words that are sung usually appear enclosed by musical notes.
1. Power Button - Press to turn the TV on or off.
2. Volume ▲/▼ Buttons - Press to raise or lower the volume of the sound.
(MENU Buttons) - Press the both button to display the On- Screen menu function.
(SET+/– Buttons) - Press the select the desired setting during On-Screen operations.
3. Channel ▲/▼ Buttons - Press to select a higher or lower numbered channel set into
memory.
(ENTER Buttons)- Press to enter or select information for On-Screen operations.
(RESET Buttons) - Press to reset the On-Screen picture adjustments to their factory preset
positions.
4. Remote Sensor - Signals from the Remote Control unit are received here.
For television programs broadcasting with Closed Captions, look in your TV guide for the
Closed Captions symbol (CC).
SETTING LANGUAGE
• When activating the Closed Captioned Decoder, there will be a short delay before the
Closed Captioned text appears on the screen.
• Closed Captioned text is only displayed in locations where it is available.
• If no caption signal is received, no captions will appear, but the television will remain in
the Caption Mode.
• Misspellings or unusual characters may occasionally appear during Closed Captioning.
This is normal with Closed Captioning, especially with live programs. This is because
during live programs, captions are also entered live. These transmissions do not allow
time for editing.
• When Captions are being displayed, on-screen displays, such as volume and mute may
not be seen or may interfere with Closed Captions.
• Some cable systems and copy protection systems may interfere with the Closed
Captioned signal.
This TV can display the channel number, on screen displays and picture adjustments on the
screen in English, Spanish or French.
On-screen language selection (step 3) will automatically appear on the screen when you press
the MENU button initially. Select language to use the other menu options.
MENU
Press the MENU button.
CH SET
1
PICTURE
LANGUAGE
Press the SET + or – button to select the LANGUAGE
mode, then press the ENTER button.
V-CHIP SET
2
PRESS : + / – / ENTER / MENU
• If using an indoor antenna or if TV reception is very poor, the Closed Caption Decoder
may not appear or may appear with strange characters or misspelled words. In this
case, adjust the antenna for better reception or use an outdoor antenna.
Press the SET + or – button until the " " indicator
points to the desired language: English (ENGLISH),
Spanish (ESPAÑOL) or French (FRANCAIS), then
press the ENTER button.
3
LANGUAGE / LENGUA / LANGUE
ENGLISH
ESPAÑOL
FRANCAIS
SETTING V-CHIP
PRESS : + / – / ENTER / MENU
Press the MENU button again.
4
This TV is fitted with a V-CHIP controller which provides you with channel viewing access
controls and restrictions.
NOTE:
If Spanish or French is chosen, the Closed Caption indicators will be in the selected language,
but the Closed Caption text will not be affected by the language selection.
1
Press the SET + or – button to select the V-CHIP SET option, then press the ENTER button.
Enter your password using the Direct channel selection buttons.
In the event of entering incorrect password press the RESET button. Then press the
ENTER button.
TV OPERATION
2
To turn on the TV, press the POWER button.
1
Enter the same password for confirmation, then press the ENTER button.
3
The Volume can be adjusted to a desired level by pressing the VOL (VOLUME) ▲ or ▼
button.
2
Press the SET + or – button to select the V-CHIP option.
Press the ENTER button to select the ON.
4
The sound level will be indicated on the TV screen by GREEN BARS AND A NUMBER.
As the sound level increases, so do the number of BARS AND THE NUMBER on the
screen. The same is true for decreasing the level.
Press the SET + or – button to select the TV RATING or MOVIE RATING option. Press
the ENTER button.
5
Set the TV/CATV menu option to the appropriate position. When shipped from the
factory, this menu option is in the CATV setting. See "To Memorize Channels".
Press the SET + or – button to select the desired rating for the applicable video or TV
channel. Press the ENTER button.
3
6
TV - VHF/UHF channels
CATV - CABLE TV channels
TV RATING
SET –
TV-Y7
SET +
TV-G TV-PG
OFF
TV–Y
TV-14
TV-MA
CH (CHANNEL) ▲ and ▼ buttons
4
Press and release the CH (CHANNEL) ▲ or ▼ button. The channel automatically stops
at the next channel set into memory. Press and hold the button down to change channels
more quickly.
TV-Y : all children
TV-PG : parental guidance
TV-14 : 14 years old and above
TV-MA : 17 years old and above
TV-Y7 : 7 years old and above
TV-G : childrens program
For proper operation, before selecting channels, they should be set into the TV's
memory. See "To Memorize Channels".
When you select TV-Y7, TV-PG, TV-14 or TV-MA, press the CALL button to show the
contained rating.
DIRECT CHANNEL SELECTION buttons (0-9) - Press these buttons to select a
channel.The channel number will appear on the upper right corner of the TV screen. If an
invalid channel number is selected, the display will revert to the original channel.
TV MODE DIRECT CHANNEL SELECTION - When the TV/CATV menu option is in the
TV position, all channels can be instantly selected by using two buttons. (For example, to
select channel 2, press "0", then "2". If you press only "2", channel selection will be
delayed for a few seconds). For channels 10 and above, press the 2 digits in order.
Press the SET + or – button to select the the desired item you want. Press the ENTER button
to select the OFF.
MOVIE RATING
SET –
PG
SET +
PG-13
OFF
G
R
NC-17
X
G
PG
: all ages
: parental guidance
R
: under 17 years old parental
guidance suggested
NC-17 : 17 years old and above
: adult only
NOTE FOR CHANNELS 1-19:
If only 1 or 2 buttons are pressed, the corresponding channel will be selected in 4
seconds.
PG-13 : parental guidance
less than 13 years old
X
Press the MENU button three times to return to normal TV viewing.
7
CATV mode direct channel selection -
When the TV/CATV menu option is in the CATV position, channels can be selected as
follows:
NOTES:
• The V-Chip function is activated only on programs and tapes that have the rating signal.
• Once you block a program using the V-Chip function, the blocked program cannot be
watched based on the content of the show. When the program starts, the "ENTER
PASSWORD" will appear on the screen. When you want to release the V-Chip temporarily,
enter the password.
If you change the channel or turn off and on the TV while releasing the V-Chip temporarily,
the V-Chip setting will be resumed.
• When you watch the TV from the cable box or the VCR with the RF Modulator, then you
release the V-Chip temporarily, the V-Chip setting will not be resumed until you turn off the TV.
The TV channel is not used in this case.
1-9
Press "0" twice, then 1-9 as needed.
(Example, to select channel 2, press 002)
Press "0", then remaining 2 digits.
(Example, to select channel 13, press 013).
Press the 2 digits in order.
10-19
20-99
100-125
(Example, to select channel 36, press 36).
Press the 3 digits in order.
(Example, to select channel 120, press 120).
• When changing the channel with the cable box or the VCR, approximately 10 seconds will
pass until the program appears.
NOTE: If the station being viewed stops broadcasting, the TV will automatically shut off
after 15 minutes.
3I0-0101A E
4
1/1/32, 09:50
ADJUSTING PICTURE
TO MEMORIZE CHANNELS
You can adjust the settings for color, sharpness, contrast, brightness and tint.
This TV is equipped with a channel memory feature which allows channels to skip up or down
to the next channel set into memory, skipping over unwanted channels.
Before selecting channels, they must be programmed into the TV's memory. In addition to
normal VHF and UHF channels, this TV can receive up to 113 Cable TV channels. To use this
TV with an antenna, set the TV/CATV menu option to the TV setting. When shipped from the
factory, this menu option is in the CATV setting.
Press the MENU button.
1
Press the SET + or – button until the indicator next to "PICTURE" begins
to flash, then press the ENTER button.
2
TV/CATV SELECTION
3
Press the ENTER button repeatedly to select the item you want to adjust.
BRIGHTNESS CONTRAST COLOR TINT SHARPNESS
Press the MENU button.
1
MENU
CH SET
PICTURE
Press the SET + or – button until the indicator next to "CH SET"
begins to flash, then press the ENTER button.
2
LANGUAGE
V-CHIP SET
PRESS : + / – / ENTER / MENU
Press the SET + or – button to adjust the setting.
4
Press the SET + or – button until the indicator next to "TV/CATV"
begins to flash.
3
TV
CATV
AUTO CH MEMORY
ADD / DELETE
+
–
Press the ENTER button to select the TV or CATV mode. The
arrow indicates the selected mode.
4
5
BRIGHTNESS
CONTRAST
COLOR
increase brightness
increase contrast
brilliant color
decrease brightness
decrease contrast
pale color
PRESS : + / – / ENTER / MENU
Press the MENU button twice to return to normal TV viewing.
The chart below is typical of many cable system channel allocations.
TINT
greenish color
reddish color
CATV CHART
makes picture
clearer
SHARPNESS
makes picture softer
Number on this TV
Corresponding CATV channel
14
A
15
B
16
C
17
D
18
E
19
F
20
G
21
H
22
I
23
J
24
K
25
L
26
M
27
N
28
O
29
P
30
Q
31
R
32
S
33
T
34
U
35
V
36
W
37
38
39
40
AA BB CC DD
41
42
43
44
45
II
63
46
JJ
64
47
48
49
50
51
52
53
54
55
56
57
58
TO RETURN TO INITIAL SETTING
Press the RESET button while the picture adjusting mode appears on-screen.
EE FF GG HH
KK LL MM
NN OO PP QQ RR SS TT UU VV
59
60
61
62
65
66
67
68
III
69
70
71
73
74
75
76
72
MMM
WW AAA BBB CCC DDD EEE FFF GGG HHH
JJJ KKK LLL
NNN OOO PPP QQQ
77
78
79
80
81
82
83
84
85
86
86
87
87
88
88
89
89
90
90
91
91
92
92
93
93
94
94
RRR SSS TTT UUU VVV WWW XXX YYY ZZZ
95
96
97
98
99 100 101 102 103
104 105 106 107 108 109 110 111 112
104 105 106 107 108 109 110 111 112
122 123 124 125 01
122 123 124 125 5A
TROUBLESHOOTING GUIDE
A-5 A-4 A-3 A-2 A-1 100 101 102 103
113 114 115 116 117 118 119 120 121
113 114 115 116 117 118 119 120 121
Before requesting service, please refer to the following chart for the symptom and possible solution.
NOTE: Contact your cable company to determine the type of cable system used in your area.
SYMPTOMS
POSSIBLE SOLUTIONS
• Make sure the power cord is plugged in.
• Try another AC outlet.
AUTOMATIC CHANNEL MEMORY
TV does not operate
MENU
• Power is off, check fuse or circuit breaker.
• Unplug unit for an hour, then plug it back in.
Press the MENU button.
1
CH SET
PICTURE
LANGUAGE
• Station or CATV experiencing problems, tune to another station.
• Check sound adjustments (Volume and Muting).
• Check for sources of possible interference.
Press the SET + or – button until the indicator next to "CH SET"
begins to flash, then press the ENTER button.
2
V-CHIP SET
Poor sound or No sound
Poor picture or No picture
PRESS : + / – / ENTER / MENU
TV
CATV
Press the SET + or – button until the indicator next to "AUTO CH
MEMORY" begins to flash, then press the ENTER button. The
TV will begin memorizing all the channels available in your area.
3
• Station or CATV experiencing problems, tune to another station.
• Check antenna or CATV connections, adjust antenna.
• Check for sources of possible interference.
AUTO CH MEMORY
ADD / DELETE
PRESS : + / – / ENTER / MENU
• Check picture control adjustments.
4
Press the MENU button twice to return to normal TV viewing.
• Station or CATV experiencing problems, tune to another station.
• Station signal is weak, adjust antenna to receive weaker station.
• Check for sources of possible interference.
Poor reception on some
channels
TO ADD/DELETE CHANNELS
• Station or CATV experiencing problems, tune to another station.
• Make sure channels are set into memory.
• Check picture control adjustments.
• Check antenna or CATV connections, adjust antenna.
• Check for sources of possible interference.
Press the MENU button.
1
MENU
Poor color or no color
CH SET
Press the SET + or – button until the indicator next to "CH SET"
begins to flash, then press the ENTER button.
PICTURE
2
LANGUAGE
V-CHIP SET
PRESS : + / – / ENTER / MENU
• Station or CATV experiencing problems, tune to another station.
• Make sure channels are set into memory.
• CATV company is scrambling signal.
Press the SET + or – button until the indicator next to "ADD/
DELETE" begins to flash, then press the ENTER button.
3
Picture wobbles or drifts
No CATV reception
TV
CATV
• Check antenna adjustment.
AUTO CH MEMORY
ADD / DELETE
Select the desired channels to be memorized or deleted using
the Direct Channel Selection buttons (10 keys, 0-9), the CH ▲ or
4
• Check all CATV connections.
• Set TV/CATV menu option to the CATV mode.
• Station or CATV system problems, try another station.
PRESS : + / – / ENTER / MENU
▼ button or the SET + or – button.
ADD
CH 012
Horizontal or diagonal
bars on screen
• Check antenna connections, adjust antenna.
• Check for sources of possible interference.
Press the ENTER button to select ADD or DELETE.
5
If an unmemorized channel was selected (step 4), the channel
indication will be red. Press the ENTER button if you wish to ADD
the unmemorized channel. The channel indicator will change
from red to green when a channel is added and the channel will
be memorized.
• Make sure TV/CATV menu option is in the appropriate mode.
• If using antenna, check UHF antenna connections.
No reception above
channel 13
PRESS : + / – / ENTER / MENU
• Batteries are weak, dead or inserted incorrectly.
• Remote is out of range, move closer to TV within 15 feet.
• Make sure Remote is aimed at sensor.
• Confirm there are no obstructions between the Remote and the TV.
• Make sure the power cord is plugged in.
No Remote operation
TV shuts off
If a memorized channel was selected (step 4), the channel
indication will be green.
Press the ENTER button if you wish to DELETE the channel from
memory. The channel indicator will change from green to red
when a channel is deleted.
• No broadcast on station tuned.
• Sleep Timer is set.
• Power interrupted.
Repeat Steps 4 and 5 for each channel to be added or deleted.
• TV station experiencing problems or program tuned is not closed
captioned. Try another channel.
• Check CATV connection or VHF/UHF antenna, reposition or rotate
antenna.
Press the MENU button three times after adding or deleting all of
the desired channels, to return to normal TV viewing.
6
Closed - Caption is not
activated.
• Press TV/CAPTION/TEXT button to turn on the closed caption de-
coder.
• Select proper language in the menu options.
Display is not shown in
your language.
3I0-0101A E
5
1/1/32, 09:51
|