MKS2114
User’s Guide
Portable CD/CD+G
Karaoke System
Before operating this product,
please read these instructions completely.
Dear Customer:
Selecting fine audio equipment such as the unit you’ve just purchased is only the start of your musical
enjoyment. Now it’s time to consider how you can maximize the fun and excitement your equipment offers.
This manufacturer and the Electronic Industries Association’s Consumer Electronics Group want you to get
the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and
clear without annoying blaring or distortion and, most importantly, without affecting your sensitive hearing.
Sound can be deceiving. Over time your hearing “comfort level” adapts to higher volumes of sound. So what
sounds “normal” can actually be loud and harmful to your hearing. Guard against this by setting your
equipment at a safe level BEFORE your hearing adapts.
To establish a safe level:
• Start your volume control at a low setting.
• Slowly increase the sound until you can hear it comfortably and clearly, and without distortion.
Once you have established a comfortable sound level:
• Set the dial and leave it there.
Taking a minute to do this now will help to prevent hearing damage or loss in the future. After all, we want
you listening for a lifetime.
We Want You Listening For A Lifetime
Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since hearing damage
from loud noise is often undetectable until it is too late, this manufacturer and the Electronic Industries
Association’s Consumer Electronics Group recommend you avoid prolonged exposure to excessive noise.
This list of sound levels is included for your protection.
Decibel
Level
30
Example
Quiet library, soft whispers
40
50
60
70
Living room, refrigerator, bedroom away from traffic
Light traffic, normal conversation, quiet office
Air conditioner at 20 feet, sewing machine
Vacuum cleaner, hair dryer, noisy restaurant
Average city traffic, garbage disposals, alarm clock at two feet
80
THE FOLLOWING NOISES CAN BE DANGEROUS UNDER CONSTANT EXPOSURE:
90
Subway, motorcycle, truck traffic, lawn mower
Garbage truck, chain saw, pneumatic drill
Rock band concert in front of speakers, thunderclap
Gunshot blast, jet engine
100
120
140
180
Rocket launching pad
Information courtesy of the Deafness Research Foundation.
EIA
EST. 1924
We
WantYou
LISTENING
ForALifetime
2
SAFETY INSTRUCTIONS
Before using the unit, be sure to read all operating instructions
15. OVERLOADING
carefully. Please note that these are general precautions and may not
pertain to your unit. For example, this unit may not have the capability
to be connected to an outdoor antenna.
Do not overload wall outlets and extension cords as this can result in a
risk of fire or electric shock.
16. OBJECT AND LIQUID ENTRY
1. READ INSTRUCTIONS
Never push objects of any kind into this product through openings as they
may touch dangerous voltage points or short out parts that could result in
fire or electric shock. Never spill or spray any type of liquid on the product.
17. OUTDOOR ANTENNA GROUNDING
All the safety and operating instructions should be read before the
product is operated.
2. RETAIN INSTRUCTIONS
The safety and operating instructions should be retained for future reference.
3. HEED WARNINGS
All warnings on the product and in the operating instructions should be
adhered to.
4. FOLLOW INSTRUCTIONS
All operating and use instructions should be followed.
5. CLEANING
Unplug this product from the wall outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners. Use a dry cloth for cleaning.
6. ATTACHMENTS
If an outside antenna is connected to the product, be sure the antenna
system is grounded so as to provide some protection against voltage
surges and built-up static charges. Section 810 of the National Electric
Code, ANSI/NFPA 70, provides information with respect to proper
grounding of the mast and supporting structure, grounding of the lead-
in wire to an antenna discharge product, size of grounding conductors,
location of antenna discharge product, connection to grounding
electrodes and requirements for grounding electrodes.
ANTENNA
LEAD IN
WIRE
Do not use attachments not recommended by the product's
manufacturer as they may cause hazards.
7. WATER AND MOISTURE
GROUND
CLAMP
Do not use this product near water–for example: near a bathtub,
washbowl, kitchen sink or laundry tub; in a wet basement; or near a
swimming pool.
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
8. ACCESSORIES
Do not place this product on an unstable cart, stand, tripod, bracket or
table. The product may fall, causing serious injury and serious damage to
the product. Use only with a cart, stand, tripod, bracket or table
ELECTRIC
SERVICE
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
EQUIPMENT
GROUND CLAMPS
recommended by the manufacturer or sold with the
product. Any mounting of the product should follow the
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
NEC - NATIONAL ELECTRICAL CODE
(NEC ART 250, PART H)
PORTABLE CART WARNING
(symbol provided by RETAC)
S2898A
manufacturer’s instructions, and should use a mounting
accessory recommended by the manufacturer.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
8A. An appliance and cart combination should be moved
with care. Quick stops, excessive force and uneven
surfaces may cause the appliance and cart
18. SERVICING
combination to overturn.
9. VENTILATION
Do not attempt to service this product yourself as opening or removing
covers may expose you to dangerous voltage or other hazards. Refer
all servicing to qualified service personnel.
Slots and openings in the cabinet and in the back or bottom are
provided for ventilation, to ensure reliable operation of the product and
to protect it from overheating. These openings must not be blocked or
covered. The openings should never be blocked by placing the product
on a bed, sofa, rug or other similar surface. This product should never
be placed near or over a radiator or heat source. This product should
not be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer's instructions
have been adhered to.
19. REPLACEMENT PARTS
When replacement parts are required, be sure the service technician
uses replacement parts specified by the manufacturer or those that
have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or other hazards.
20. SAFETY CHECK
Upon completion of any service or repairs to this product, ask the
service technician to perform safety checks to determine that the
product is in proper operating condition.
10. POWER SOURCES
This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power
supply to your home, consult your appliance dealer or local power
company. For products intended to operate from battery power, or
other sources, refer to the operating instructions.
21. WALL OR CEILING MOUNTING
The product should be mounted to a wall or ceiling only as
recommended by the manufacturer.
22. DAMAGE REQUIRING SERVICE
Unplug the product from the wall outlet and refer servicing to qualified
11. GROUNDING OR POLARIZATION
service personnel under the following conditions:
This product is equipped with a polarized alternating-current line plug
(a plug having one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you are unable to
insert the plug fully into the outlet, try reversing the plug. If the plug
should still fail to fit, contact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the polarized plug.
12. POWER-CORD PROTECTION
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled or objects have fallen into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operating instructions, as an adjustment of other controls may result
in damage and will often require extensive work by a qualified
technician to restore the product to its normal operation.
e. If the product has been dropped or the cabinet has been damaged.
Power-supply cords should be routed so that they are not likely to be
walked on or pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience receptacles, and the
point where they exit from the appliance.
f.
When the product exhibits a distinct change in performance–this
indicates a need for service.
13. LIGHTNING
23. HEAT
The product should be situated away from heat sources such as
radiators, heat registers, stoves or other products (including amplifiers)
that produce heat.
24. NOTE TO CATV SYSTEM INSTALLER
To protect your product from a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line surges.
14. POWER LINES
This reminder is provided to call the CATV system installer's attention
to Article 820-40 of the NEC that provides guidelines for proper
grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building, as close to the point
of cable entry as practical.
An outside antenna system should not be located in the vicinity of
overhead power lines or other electric light or power circuits, or where it
can fall into such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be fatal.
3
LOCATION OF CONTROLS
FRONT
FRONT
1. Carrying Handle
2. CD Compartment
3. REPEAT Button
4. MASTER VOLUME
Control
1
2
5. PROGRAM Indicator
6. REPEAT Indicator
7. Display
14
15
16
3
4
5
6
7
8
9
8. PLAY/PAUSE Indicator
9. Skip/Search (o) Button
10. Stop (I) Button
11. POWER Control
12. Speaker
17
18
10
19
11
12
20
21
13. MIC 1 Jack
13
22
14. CD OPEN/CLOSE Area
15. PROGRAM Button
16. MIC VOLUME Control
17. Skip/Search (n) Button
18. Play/Pause (®p) Button
19. ECHO Control
REAR
20. AVC (Auto Voice) Control
21. Speaker
22. MIC 2 Jack
23
24
REAR
23. VIDEO OUT Jack
24. AUDIO OUT (Left & Right)
Jacks
25. AC Jack
25
26
26. Battery Compartment
(Bottom of Unit)
4
POWER SOURCES
AC:
Use the AC polarized line cord included with the unit for operation on AC power. Insert the small end of the
AC cord into the AC jack on the rear of the unit. Insert the other end of the AC cord into any convenient
120V 60Hz household outlet.
AC Outlet
AC Plug
NOTE: The AC plug supplied with the unit is polarized to help minimize the possibility of electric shock. If the
AC plug does not fit into a nonpolarized AC outlet, do not file or cut the wide blade. It is the user’s
responsibility to have an electrician replace the obsolete outlet.
DC:
Remove the Battery Compartment
cover on the bottom of the unit by
sliding it out and then up and insert
eight (8) “C” cell batteries (not
included), observing the battery
polarity indicated inside the
compartment. Replace the Battery
Compartment cover.
+
+
+
+
+
+
+
NOTE: We recommend Alkaline batteries for longer life and best performance.
BATTERY PRECAUTIONS
Follow these precautions when using batteries in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery
compartment. Reversed batteries may cause damage to the device.
3. Do not mix different types of batteries together (e.g. Alkaline, Carbon-zinc and rechargeable) or old
batteries with fresh ones.
4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury
from possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow
battery manufacturer’s directions.)
5
OPTIONAL CONNECTIONS
If you are using special CD+G (Graphics) discs in this portable Karaoke system, you must connect this unit
to a television set in order to see the On-Screen Graphics that are recorded on CD+G Karaoke discs.
The video cable has yellow RCA type plugs on each end. Please note that your TV set must have an RCA
type Video Input Jack in order to view the CD+G lyrics on your TV screen. You cannot connect this portable
Karaoke system to your TV’s coaxial antenna terminal.
Also note that On-Screen Graphics are only available on special Karaoke compact discs that
bear the CD+G mark.
COMPACT
Many newer TV sets have a set of Video and Stereo Audio jacks on the front panel for quick and
easy connections without having to turn the TV set to gain access to the jacks on the back panel.
DIGITAL AUDIO
GRAPHICS
If your TV set has such front panel A/V jacks, we suggest that you use those jacks to connect
your portable Karaoke system.
After connecting the Video Out jack on this portable Karaoke system to the Video In jack on your TV with the
included video cable, you have the following three choices:
1. Listen to the sound from the built-in speakers in this portable Karaoke system. In this case, no external
audio connections are required.
From
Video
Out
To
Video
In
TELEVISION
2. If your TV has stereo audio input jacks, you can connect the Audio Out jacks on the back of this unit to
the Audio In jacks on your TV. The stereo audio connection cable is included. In this case, the lyrics from
the CD+G disc will appear on your TV screen and the sound from the disc will be heard from your TV
speakers.
Note: If you have a mono TV with only one Audio In jack, you may have to purchase a “Y” adapter (stereo to
mono) at your local electronics accessories store in order to combine the Left and Right stereo channels
from this portable Karaoke system to a single mono channel for connection to your mono TV.
From
Video Out
From
Audio Out
To
Video
In
To
Audio In
FRONT OF
TELEVISION
6
OPTIONAL CONNECTIONS (CONTINUED)
3. You can connect the Audio Out jacks from this portable Karaoke system to the Aux In or Audio In jacks of
your home stereo system to hear the sound through your home stereo speakers. Follow the instructions
for your home stereo system to select the device connected to the external jacks as the audio source.
From
Video Out
From
Audio Out
To
Video
In
RECEIVER OR HOME STEREO
To
Audio In
7
OPERATION
CONNECTING THE MICROPHONE(S)
This unit has two microphone jacks which will allow you to sing along with your favorite songs. Before
connecting, make sure the MIC VOLUME control is set to minimum.
AUTO VOICE CONTROL (AVC)
ECHO CONTROL
When the VOCAL feature is activated, the vocals on a multiplex
recording are muted as soon as the singer begins singing into
the microphone. When the singer stops singing, the vocals are
automatically unmuted. Adjust the AUTO VOICE control for the
best balance between playback and microphone levels.
Rotate the ECHO control clock-
wise to increase the echo or
counterclockwise to decrease the
echo.
IMPORTANT: This feature only works with multiplex CDs.
MIC ON/OFF SWITCH
To turn the microphone on, slide
the ON/OFF switch, located on
the side of the microphone, to the
ON position. To turn the
microphone off, slide the ON/OFF
switch to the OFF position.
8
OPERATION (CONTINUED)
PLAYING COMPACT DISCS
NORMAL PLAYBACK
(For karaoke playback, please refer to page 13)
1
2
3
Set the MASTER VOLUME Rotate the POWER control to the Press the OPEN/CLOSE area to
control to a low setting.
ON position to turn the unit on.
open the CD compartment door.
Place a CD on the center spindle,
with the printed label side facing
up. Close the CD compartment
door.
4
5
6
The CD player will read the table
of contents on the disc and the
total number of tracks will appear
in the display.
Adjust the MASTER VOLUME
control as desired. Playback will
continue until all the tracks on the
disc have been played.
Press the Play/Pause (¨ )
button to begin playback on
Track 1; the PLAY/PAUSE
indicator will light.
7
8
9
To stop playback before the disc After the last track has been Remove your disc, close the CD
ends, press the Stop (I) button. played, the disc stops auto- compartment door and rotate the
matically and the display shows POWER control to the OFF
the total number of tracks on the position.
disc. If you are finished listening,
The disc will stop and the display
will show the total number of
tracks on the disc.
press the OPEN/CLOSE area to
open the CD Compartment door.
9
OPERATION (CONTINUED)
2
CD PAUSE CONTROL
1
During CD playback, if you wish
to pause the disc momentarily,
press the Play/Pause (¨ )
Press the Play/Pause (¨ )
button again to release pause and
resume normal CD playback; the
button. Playback stops but the PLAY/PAUSE indicator will
disc continues to spin and the remain on.
PLAY/PAUSE indicator will blink.
TO BEGIN PLAYBACK FROM A SPECIFIC TRACK
1
2
2
1
After you insert the disc into the CD
player and the total number of
tracks appear on the display, you
may press either the Skip/Search
When the desired track number
blinks in the display, within five
seconds, press the Play/Pause
(¨ ) button. Playback will begin
on the track you selected.
(
) ‚ or (
) ƒ button to select
a specific track for playback.
FORWARD/REVERSE SKIP TRACK AND HIGH-SPEED MUSIC SEARCH (
/
)
1
2
3
CD ONLY
During playback, depress and
hold either the Skip/Search (
or ( ) button to move the player
)
forward or backward within a
track to locate a specific musical
passage. The player will move
forward or backward at high
speed as long as the button is
depressed. When you release the
During playback, press the During playback, press the
Skip/Search ( ) button once to Skip/Search ( ) button once to
advance the player to the move the player back to the
beginning of the next track. Press beginning of the current track. Press
Skip/Search (
) or (
) button,
the Skip/Search (
) button the Skip/Search (
) button
normal playback will resume.
repeatedly to advance the player repeatedly to move the player back
to higher-numbered tracks.
to lower-numbered tracks.
10
OPERATION (CONTINUED)
REPEAT PLAYBACK
1
2
3
1
1
1
3
2
To repeat a single track, press the To repeat all of the tracks on a To cancel Repeat Playback,
REPEAT button ‚ once; the disc continuously, while in the press the REPEAT button ‚ until
Stop mode, press the REPEAT
button ‚ twice; the REPEAT
REPEAT indicator will blink.
Press the Skip/Search ( ) ƒ or
) „ button to select the
specific track that you wish to
the REPEAT indicator goes out.
You can also cancel Repeat
indicator will light solid. Press the Playback by pressing the Stop
(I) button ƒ.
(
Play/Pause (¨ ) button ƒ to
repeat. When the desired track repeat all tracks.
number blinks in the display,
within five seconds, press the
PLAY/PAUSE (¨ ) button ꢀ to
begin playback. The specific track
you selected will be repeated
continuously.
PROGRAMMED PLAYBACK
The CD player in this unit has a 19 track programmable memory that allows you to program up to 19 tracks
on any disc for playback in any desired order. You may program 19 different tracks or you may also program
certain tracks to play more than once.
To perform programmed playback, proceed as follows:
1
2
3
Rotate the POWER control to the Press the OPEN/CLOSE area to Press the PROGRAM button; “0”
ON position to turn the unit on.
open the CD compartment door. will blink in the display and the
Place a CD on the center spindle, PROGRAM indicator will blink.
with the printed label side facing
up. Close the CD compartment
door.
PROGRAMMED PLAYBACK CONTINUED ON THE NEXT PAGE
11
OPERATION (CONTINUED)
4
5
6
3
1
3
1
3
1
2
2
2
Press the Skip/Search (
) ‚ or
Press either the Skip/Search (
)
Repeat step 5 until you have
‚ or ( ) ƒ button to select the programmed the desired track
(
) ƒ button to select the first
numbers into the CD Program
Memory.
When the memory is full, “- -” will
blink in the display.
track that you wish to program. next track you wish to program.
When the desired track number When the desired track number
blinks in the display, press the blinks in the display, press the
PROGRAM button „ again.
PROGRAM button „ again.
Press the PLAY/PAUSE (¨p) button ‚ to begin programmed
playback. The PROGRAM indicator will blink and playback will begin
on the first track that you programmed. The player will continue to play
all of the tracks that you programmed in the order in which you
programmed them. When the last programmed track has been played,
the player will stop and the display will again show the total number of
tracks on the disc. If you press the PROGRAM button ƒ and then
7
2
press the PLAY/PAUSE (¨p) button ‚ again, playback will start on
the first track you programmed and will continue until all the
programmed tracks have been played.
1
To clear programmed playback, while in the Stop mode, press the PROGRAM button followed by the
STOP (I) button or open the CD door.
To check the programmed tracks, while in the Stop mode, press the PROGRAM button repeatedly to view
the programmed tracks.
PROGRAMMED REPEAT
1
2
3
It is also possible to use the
Program and Repeat functions Press the Play/Pause (¨ )
Programmed Repeat operation
will continue indefinitely until you
press the Stop (I) button or open
the CD door.
button to begin programmed
repeat playback. The player will
play the tracks you selected in the
order in which you programmed
them. When the last track in the
program has been played, the
entire program will begin again.
together to repeat a specific
program indefinitely. First, program
the tracks you wish to hear in the
order you wish to hear them, as
described above. Then, press the
REPEAT button twice. The
PROGRAM indicator will blink and
the REPEAT indicator will light.
12
OPERATION (CONTINUED)
PLAYING A CD+G (COMPACT DISC + GRAPHICS) KARAOKE DISC
You can listen to a CD+G karaoke disc. CD+G discs combine the recorded music with an additional video
track that displays the song lyrics on a television screen. As the song plays, the words to be sung are
highlighted in a different color on most CD+Gs.
1
2
3
Insert a CD+G disc. Insert the
microphone(s) into the MIC
jack(s). Make sure the unit is
connected to a TV or TV and
stereo as shown on pages 6 and
7.
Adjust the AUTO VOICE control
as described below.
Press the PLAY/PAUSE (¨p)
button to start CD+G playback;
the CDG indicator will light and
the image and lyrics will appear
on the external TV, if connected.
When the AUTO VOICE feature is
activated, the vocals on a
multiplex recording are muted as
soon as the singer begins singing
into the microphone. When the
singer stops singing, the vocals
are automatically unmuted. Adjust
the AUTO VOICE control for the
best balance between playback
and microphone levels.
4
1
2
Adjust the MIC VOLUME control ‚ as desired. Increasing this control
will increase the volume of the microphone. Adjust the ECHO control ƒ
to add an echo effect to your voice. The ECHO control ƒ is variable so
add as much or as little reverb as desired. Sing or talk into the
microphone and you will hear both the CD+G and the microphone.
IMPORTANT: This feature only
works with multiplex CDs.
NOTE: The Program and Repeat features on a CD+G disc operate the same as with standard CDs.
INFORMATION ABOUT CD+G KARAOKE DISCS:
CD+G Karaoke discs are designed specifically for playback in special CD players that include a CD+G
decoder, such as this unit. These discs contain the lyrics to each song and the lyrics will appear on your TV
screen, line by line, as the disc is playing. Usually the words on the screen will change color in time with the
music to help you sing along at the proper tempo, even if you do not know the song.
Some CD+G Karaoke discs have all of the songs recorded twice, first with music only, and then with music
and vocals together. (This type of recording is called a “Multiplex” recording.) For example, if you purchase a
CD+G disc containing four songs, tracks one through four may have the music only without vocals, and
tracks five through eight might have the same four songs recorded with music on the left channel and the
vocal tracks on the right channel.
MICROPHONE FEEDBACK:
“Feedback” is a howling or screeching sound that occurs when the microphone comes too close to the
speaker(s). To avoid microphone feedback, keep the microphone as far away from the speakers as the
microphone cable will allow. If you must bring the microphone close to the speakers, such as when you are
changing a disc or adjusting one of the other controls on the front of the unit, set the microphone ON/OFF
switch to the OFF position.
13
CARE AND MAINTENANCE
Caring for Compact Discs
• Treat the compact disc carefully. Handle the compact disc
only by its edges. Never allow your fingers to come in contact
with the shiny, unprinted side of the compact disc.
• Do not attach adhesive tape, stickers, etc. to the compact
disc label.
• Clean the compact disc periodically with a soft, lint-free, dry
cloth. Never use detergents or abrasive cleaners to clean
the compact disc. If necessary, use a CD cleaning kit.
• If a compact disc skips or gets stuck on a section of the compact disc, it is probably dirty or damaged
(scratched).
• When cleaning the compact disc, wipe in straight lines from the center of the compact disc to the outer
edge of the compact disc. Never wipe in circular motions.
Z
• This unit is designed to play only compact discs bearing the identification logo as shown here.
Other discs may not conform to the CD standard and may not play properly.
• Compact Discs should be stored in their cases after each use to avoid damage.
• Do not expose compact discs to direct sunlight, high humidity, high temperatures or dust, etc.
Prolonged exposure or extreme temperatures can warp the compact disc.
• Do not stick or write anything on either side of the compact disc. Sharp writing instruments, or the ink, may
damage the surface.
Cleaning the Unit
• To prevent fire or shock hazard, disconnect your unit from the AC power source when cleaning.
• The finish on your unit may be cleaned with a dust cloth and cared for as other furniture. Use caution
when cleaning and wiping the plastic parts.
• Mild soap and a damp cloth may be used on the front panel.
14
TROUBLESHOOTING GUIDE
Should this unit exhibit a problem, check the following before seeking service:
Symptom
Possible Cause
Solution
Compact Disc Player
CD Player will not play.
CD is not installed or installed
upside-down.
Insert CD with label side up.
CD skips while playing.
Disc is dirty or scratched.
Wipe disc with cloth or use
another disc.
General
No sound.
Karaoke
Power cord disconnected.
Connect power cord.
Some vocals are still
present when AUTO
VOICE control is off.
Backup vocals are supposed
to be included.
This is normal, only the main vocal(s)
are to be reduced.
Feedback is heard
when singing.
Microphone is too close to unit
or MIC Volume is too high.
Move microphone away from
unit or decrease MIC Volume.
Words do not appear
on TV screen.
Using non-CD+G disc.
Use CD+G disc.
Video cable connected improperly to TV. Check connection; see pgs. 6-7.
Source is not selected on TV.
Change TV source to match the
location of karaoke connection (i.e.
VIDEO 1, AUX IN, etc.).
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE, PLEASE VISIT OUR WEBSITE AT
WWW.MEMOREXELECTRONICS.COM
OR CONTACT CUSTOMER SERVICE AT (954) 660-7100.
PLEASE KEEP ALL PACKAGING MATERIAL FOR AT LEAST 90 DAYS IN CASE YOU NEED TO
RETURN THIS PRODUCT TO YOUR PLACE OF PURCHASE OR TO MEMOREX.
FOR PARTS AND ACCESSORIES, CONTACT FOX INTERNATIONAL AT 1-800-321-6993.
15
SPECIFICATIONS
GENERAL:
Power Source ..............................................................................................120V, 60Hz AC
Speaker ......................................................................................................2 x 3W, 8 Ohms
Output Power....................................................................................2 x 1.5W @ 10% THD
CD SECTION:
Disc Diameter...............................................................................................4.72” (120mm)
3.15” (80mm) Single CD
Optical Source....................................................................................Semiconductor Laser
Specifications are subject to change without notice.
16
|