INSTALLATION INSTRUCTIONS FOR PART 99-7008
APPLICATIONS
2003-2006
Mitsubishi Outlander
99-7008
KIT FEATURES
• DIN Radio Provision with pocket
• ISO Radio Provision with pocket
KIT COMPONENTS
A) Radio Housing B) ISO Brackets C) ISO Trim Plate
A
B
C
TOOLS REQUIRED:
Panel Removal Tool or
Small Flat Blade Screwdriver
•
Phillips Screwdriver
1-800-221-0932
© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION
DASH DISASSEMBLY
99-7008
MITSUBISHI OUTLANDER 2003-2006
A
Disconnect the negative battery
1
terminal to prevent an accidental
short circuit.
2
3
Remove all (3) climate control knobs.
(Figure A)
Remove (2) Phillips head screws
from behind the (2) outside climate
control knobs. (Figure A)
B
Unsnap the top edge of the trim
panel below the Climate controls. It
is not necessary to completely
remove this panel. (Figure B)
4
C
Unsnap and remove the radio/climate
5
control trim panel. (Figure C)
Remove (4) Phillips head screws
securing the radio. Unplug and
remove the radio.
6
1
KIT ASSEMBLY
99-7008
DIN MOUNT RADIO PROVISION WITH POCKET
A
Slide the DIN cage (supplied with radio)
into the Radio Housing from the front.
(Figure A)
1
B
Secure DIN cage to radio housing by
bending the locking tabs outward.
(Figure B)
2
C
Slide the radio into the DIN cage until it
3
snaps into place. (Figure C)
Continue to final assembly.
2
KIT ASSEMBLY
99-7008
ISO MOUNT RADIO WITH POCKET
A
Align the holes in the ISO brackets with
the holes in the radio. Mount the
brackets to the radio using screws
supplied with the radio. (Figure A)
1
B
Slide the radio/bracket assembly into the
radio housing until it snaps into place.
(Figure B)
2
C
Snap the ISO trim-plate onto the front of
the assembled radio and housing.
(Figure C)
3
Continue to final assembly.
NOTE: To remove the radio unsnap and remove the ISO trim-plate. Using a flat
blade screwdriver disengage ISO brackets from the radio housing and slide
radio out of radio housing.
3
FINAL ASSEMBLY
99-7008
FINAL ASSEMBLY
Locate the factory wiring harness in the dash and make the connection as shown.
Metra recomends using the proper mating adapter and making the connections as
shown. (Isolate and individually tape off the ends of any unused wires to prevent
electrical short circuit.)
1
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
2
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.
A
A)
B)
C)
D)
Strip wire ends back 1/2"
Twist ends together
Solder
B
C
D
Tape
METRA / EIA WIRING CODE
12V Ignition / Acc . . . Red
Right Front (+) . . . . . Gray
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Right Front (-). . . . . . Gray / Black
Left Front (+) . . . . . . White
Left Front (-). . . . . . . White / Black
Right Rear (+). . . . . . Violet
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
4
99-7008
NOTES
5
99-7008 INSTRUCTIONS
1-800-221-0932
© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION
INST99-7008
REV. 03/14/06
|