Miele Food Warmer EGW602 14 User Manual

Operating and installation instructions

Built-in plate warmer

EGW 602 - 14

To prevent accidents and

machine damage, read

these instructions

before

installation or use.

M.-Nr. 05 478 600

Warning and Safety instructions

Technical safety

This appliance is intended for resi-

Before installation make sure that

the voltage and frequency listed on

the data plate correspond with the

household electrical supply. This data

must correspond to prevent injury and

machine damage. Consult a qualified

electrician if in doubt.

dential use only. Only use the appli-

ance for its intended purpose.

Improper use of the appliance can

lead to personal injury and material

damage. The manufacturer cannot

be held responsible for damages

caused by improper use of the plate

warmer.

The electrical safety of this appli-

ance can only be guaranteed when

continuity exists between the appliance

and an effective grounding system,

which complies with local and national

safety regulations. It is imperative that

this basic safety requirement is tested

by a qualified electrician. The manufac-

turer cannot be held responsible for the

consequences of an inadequate

This appliance complies with current

safety requirements.

Read all instructions before installing

or using for the first time.

Keep these operating instructions in

a safe place and pass them on to

any future user.

grounding system (e.g. electric shock).

This appliance must only be used

once it has been installed in

cabinetry to ensure that all electrical

components are shielded.

Read all operating and installation

instructions for any other appliance

installed in combination with the

plate warmer.

Never open the outer casing of the

appliance.

Tampering with electrical connections

or components and mechanical parts is

dangerous and can cause machine

damage.

READ ALL INSTRUCTIONS!

Warning and Safety instructions

Do not operate any appliance with

a damaged cord or plug or after

the appliance malfunctions or has been

damaged in any manner. Return the ap-

pliance to the nearest authorized servi-

ce facility for service.

Use

The temperature in the drawer can

reach up to approx. 176 °F (80 °C)

depending on the temperature selected

and how long the appliance has been

on.

Installation, repair and mainte-

nance work should be by a Miele

authorized service technician. Work by

unqualified persons could be danger-

ous and may void the warranty.

Do not touch hot surfaces. Use handles

or knobs.

Use heat-resistant oven mitts when re-

moving dishes.

Keep children away from the appli-

ance and its controls. Supervise its

use by the elderly or infirm. The appli-

ance can get very hot during use. Dan-

Before installation or service, dis-

connect the power supply to the

work area by removing the fuse, “trip-

ping” the circuit breaker, or unplugging ger of burns!

the unit.

Ensure that adults understand how

the appliance works before allow-

ing them to use it.

Do not connect the appliance to

the electricity supply by an exten-

sion cord. Extension cords do not guar-

antee the required safety of the appli-

ance, e.g danger of overheating.

Do not use the plate warmer to

re-heat, cook or keep food or

drinks warm. The condensation from

food or drinks could lead to moisture

damage in the appliance.

Do not lean or sit on the warming

drawer. This will damage the

drawer which can only hold a maximum

of 55 lbs. (25 kg).

Do not store anything in the warm-

ing drawer. Forgotten items could

melt or catch fire when the appliance is

turned on. Flammable liquids and mate-

rials should never be stored in, above

or under the plate warmer.

To prevent injuries, do not use ac-

cessories not recommended by

Miele.

Before cleaning the appliance, trip

the circuit breaker and allow the

appliance to cool.

Warning and Safety instructions

General notes

Children should not be left alone or

unattended in an area where an

appliance is in use. They should never

Disposal of an old appliance

Before discarding an old appli-

ance, disconnect the power cord

and remove any doors to prevent haz-

be allowed to sit or stand on any part of ards.

the appliance.

Caution: Do not store items of interest

to children in cabinets above or in the

plate warmer. Children climbing on the

appliance to reach these items could

be seriously injured.

Wear proper clothing. Loose-fitting

or hanging garments should never

be worn while using the plate warmer.

Use only dry, heat resistant pot

holders. Moist or damp pot holders

used on hot surfaces may result in

steam burns. Do not substitute towels

or other bulky items for pot holders.

Do not use the appliance to heat

the room. Due to the high tempera-

tures radiated, objects left near the ap-

pliance could catch fire.

Under no circumstances use a

steam cleaner to clean this appli-

ance. The steam could penetrate elec-

trical components and cause a short

circuit.

In areas subject to infestation by

cockroaches or other vermin, keep

the appliance and its surroundings

clean at all times. Any damage caused

by pests will not be covered by the ap-

pliance warranty.

Do not use outdoors.

Caring for our environment

Disposal of the packing

material

Disposal of an old appliance

Old appliances contain materials which

can be recycled. Please contact your

local recycling center about potential

recycling.

The transport and protective packing

materials are environmentally friendly

for disposal and may be recyclable.

Ensure that the appliance presents no

danger to children while waiting for dis-

posal. See the instructions in the “Warn-

ing and Safety instructions”.

Ensure that any plastic wrap is dis-

posed of safely and kept out of the

reach of babies and young children.

Danger of suffocation!

Please recycle.

Guide to the plate warmer

aOn/Off button

bTemperature control

cWarming drawer

dNon-slip mat

eRail

fOn/Off indicator light

Using the plate warmer

The plate warmer is only intended for

warming dishes.

Controls

Do not use the plate warmer to

re-heat, cook or keep food or drinks

warm. Condensation from food or

drinks could cause moisture dam-

age to the appliance.

The appliance operates with a hot air

system. A fan distributes hot air to heat

plates quickly and evenly.

A protective grill prevents any contact

with the heating element and fan.

The rail in the drawer separates the

control panel, heating element and fan

from the rest of the drawer. This pre-

vents plates from being placed too

close to the control panel and being

damaged when the drawer is pushed

in.

The controls consist of the temperature

selector knob and the On/Off button.

These are only visible when the drawer

is open.

The floor of the warming drawer has a

non-slip mat to prevent plates and

dishes sliding when the drawer is

opened and closed.

Using the plate warmer

Warming dishes

Procedure in brief:

^ Place the dishes in the warming

drawer.

^ Select the desired temperature set-

ting.

^ Turn on the appliance (j).

^ Close the drawer.

The indicator on the front of the appli-

ance lights up to show that the appli-

ance is on.

^ Turn the appliance off (k), before re-

moving warmed dishes.

The following loading examples are

given as a guide only.

Loading the drawer

6 place settings:

The quantity which can be loaded will

depend on the type and size of your

dishes.

6 dinner plates (11"/28 cm)

6 dessert bowl

3 serving bowls

2 plates (14 “/ 36 cm)

The maximum load is 55 lbs.

(25 kg.)

or one of the following:

– 20 dinner plates (11"/28 cm)

– 36 soup bowls (8"/22 cm)

– 30 dessert bowls

Do not stand plates up directly in front

of the rail. When the drawer is closed,

these will block the vents for the heated

air and prevent the dishes from warm-

ing evenly.

– 10 dinner plates (11"/28 cm)

10 soup bowls (8"/22 cm)

– 80 espresso cups

– 40 cappuccino cups

– 30 punch glasses

– 18 soup bowls (8"/22 cm)

2 soup tureens(8" x 7"/

21 cm x 18 cm)

Using the plate warmer

Selecting a temperature

Warming times

The temperature control is used to ad- Various factors will affect the warming

just the temperature setting.

times:

– material and thickness of dishes,

– quantity,

Only turn the temperature control

clockwise and then back again.

Stop when you feel a resistance.

Forcing the control past this point

will damage it.

– how dishes are arranged,

– temperature setting.

As you use the plate warmer you will

learn which settings suit your needs

best.

The heat will shut off automatically

when the selected temperature is

reached. It will turn back on again as

soon as the temperature drops below

the selected temperature.

However, the following information can

be used as a guide:

A temperature range between approxi-

mately 86 °F and 176°F (30 °C and

80 °C) can be set.

At temperature setting r of approxi-

mately 140 °F (60 °C) heating:

– 6 place settings:

30 - 35 minutes.

Recommended temperatures for

pre-heating:

– 12 place settings:

40 - 45 minutes.

– approximately 104 °F (40 °C)

b for cups and glasses. A hot drink

placed in a cup warmed to this tem-

perature will not cool as fast, while

the cup itself can be touched easily.

– approximately 140 °F (60 °C)

r for serving dishes, bowls and

plates

Food will stay hot longer if placed on

plates heated to this temperature

while the plates will not be too hot to

handle.

Cleaning and care

Mat with non-slip surface

Never use abrasive cleaners, scour-

ing pads, steel wool or caustic

(oven) cleaners on the plate warmer.

They will damage the surface.

The mat can be removed to clean the

bottom of the drawer.

Clean the mat by hand with some hot

water and liquid dish soap. Dry thor-

oughly. Do not return the mat until it is

completely dry.

Cleaning the exterior

The exterior of the plate warmer can be

cleaned with warm water and liquid

dish soap applied with a soft sponge.

Wipe dry using a soft cloth.

Stainless steel

Stainless steel surfaces can be cleaned

using a non-abrasive stainless steel

cleaner.

To help prevent resoiling, a conditioner

for stainless steel can also be used.

Apply with even pressure.

Frequently asked questions

nearest Miele Technical Service Depart-

ment.

Installation, maintenance and repairs

to the electrical components of this

appliance should only be by a quali-

fied technician in accordance with

national and local safety regulations.

. . . dishes are not warm?

Check

– whether the noise of the fan can be

heard.

Repairs and other work by unquali-

fied persons could be dangerous

and may void the warranty.

If the fan is running:

the heating element is faulty.

Some minor problems can be fixed with

out a service call:

If the fan is not running:

the fan is faulty.

What if . . .

– whether the circuit breaker has trip-

ped, the fuse has blown or the appli-

ance is unplugged.

. . . dishes are not warm enough?

Check whether,

. . . dishes are too hot?

– the appliance is on.

The temperature control is faulty.

– the correct temperature setting has

been selected.

. . . the On / Off indicator does not

light up when the appliance is turned

on?

– the vents have been blocked by

large plates or dishes.

The indicator light for the On/Off button

is bad.

– the dishes have had enough time to

warm up.

Various factors can affect how long the

dishes take to heat up, for example:

– material and thickness of dishes,

– quantity,

– how the dishes are arranged,

– temperature setting.

The times stated are only given as a

guide. As you use the plate warmer you

will learn which setting suits your needs

best.

If any of the following problems occur,

please contact your Miele dealer or the

After sales service

In the event of a fault which you cannot

correct yourself please contact:

– Your Miele Dealer

– The Miele Technical Service

Department

USA 1-800-999-1360

[email protected]

CDN 1-800-565-6435

[email protected]

When contacting the Technical Service

Department, please quote the model

and serial number of your appliance

both of which are shown on the data

plate which is next to the control panel.

Electrical connection

The electrical installation instructions

for any appliance installed in combi-

nation with the plate warmer must be

observed.

Note to the installer

Please leave these instructions with

the consumer.

When another appliance is installed

in combination with the plate warmer

to the same circuit breaker, operat-

ing both appliances at the same

time could cause an overload. If in

doubt consult a qualified electrician.

All electrical work should be done

by a qualified technician, in strict ac-

cordance with national and local

safety regulations.

Power supply

This appliance is equipped with an

approx. 6 ft (approx. 1.8 m) long power

cord with plug ready for connection to a

120 V, 15 A, 60 Hz power supply.

Installation, repairs and other work

by unqualified persons could be

dangerous and may void the war-

ranty.

Make sure power is not supplied to

the appliance while installation or re-

pair work is being performed.

WARNING:

THIS APPLIANCE MUST BE

GROUNDED

Installation options

The plate warmer may only be installed Steam oven

beneath one of the following Miele ap-

pliances:

– Steam oven (DG 155)

– Coffee machine (CVA 610)

Read all the operating and installa-

tion instructions for any other appli-

ance installed in combination with

the plate warmer.

The cabinet dimensions required will

depend on which appliance the

plate warmer is installed with.

When installed in combination with

another appliance, the plate warmer

must always be installed beneath

the other appliance. A shelf between

Coffee machine

the appliances is not necesary.

Do not operate the appliances until

they have been completely installed.

Installing the plate warmer

The plate warmer must be installed

above a fixed interim shelf within the

cabinet to ensure that the cabinetry

can support the weight of it and of

any other appliance installed in

combination with it.

When installed in combination with

another appliance, the plate warmer

must always be installed beneath

the other appliance. A shelf between

the appliances is not necesary.

^ Trip the circuit breaker to the outlet.

^ Plug the plate warmer into the outlet.

^ Push the appliance into the cabinetry

and align it.

^ Open the plate warmer drawer and

use two screws to secure the plate

warmer to the side walls of the

cabinetry.

Installing the plate warmer

Adhering the insulation strips

Aligning the front of the plate warmer

^ Remove the protective foil from the

adhesive strips.

After installing the combination appli-

ance, it may be necessary under cer-

tain circumstances to

– align the front of the plate warmer.

– align the gap between the plate

warmer and the combination appli-

ance.

To help you do this, there are adjusting

points underneath the nuts which se-

cure the drawer to the telescopic run-

ners.

^ Align the metal strips flush against

the side and rear walls of the cabinet

a and stick them on to the plate

warmer b (see illustration).

The third metal strip is not needed if the

cabinetry does not have a rear panel.

^ Install the combination appliance in

accordance with its own specific op-

erating/installation instructions and

then connect the electrical supplies.

^ Loosen the nuts and take the plate

warmer drawer out.

Use the adjusters to align the drawer

correctly.

Alteration rights reserved / 22 / 001

M.-Nr. 05 478 600 (EGW 602 - 14)

USA / CDN - 3401

This paper consists of cellulose which has been bleached without the use of chlorine.

National GPS Receiver ADC12010 User Manual
Nikon Camera Lens MH 22 User Manual
Nordyne Furnace M3RL User Manual
NuTone Marine Heating System 665RF User Manual
Omega Thermometer HH501AK User Manual
One for All Universal Remote URC 7541 User Manual
Palsonic Portable DVD Player TFTV100A User Manual
Panasonic Air Compressor DA51C72RCU6 User Manual
Panasonic CD Player SC AK610 User Manual
Panasonic Stereo Amplifier CY M7002EUC User Manual