Musical Fidelity Stereo Amplifier X LPSV8 User Manual

X-LPSV8  
X-SERIES MM/MC INPUT PHONO AMPLIFIER  
INSTRUCTIONS FOR USE  
Thank you for purchasing the Musical Fidelity X-LPS V8 phono amplifier  
This amplifier features our top quality low noise, low distortion phono stage which very closely follows the  
RIAA equalisation curve for the optimum in sonic accuracy from vinyl sources. The XLPS V8 caters for both  
moving magnet and moving coil cartridges to allow maximum choice when selecting a cartridge.  
The X-LPS V8 is a perfect answer to most phono amplifier requirements in a single, beautifully engineered  
package.  
Used properly and carefully, it should give many years of outstanding musical reproduction.  
Dust regularly with a soft duster or soft brush, but be careful when using cleaning or polishing agents - they  
may harm the surface finish.  
If you have any questions about your audio system,  
Please consult your dealer who is there to help and advise.  
 
X-LPSV8  
GENERAL ADVICE  
INSTALLATION PRECAUTIONS & USER INFORMATION  
This new X-LPS V8 is designed and built to provide trouble-free performance, but as with all electronic devices it is  
necessary to observe a few precautions:  
Heed all warnings shown on the back of the product.  
Only connect the X-LPS V8 power supply to a mains outlet having the same voltage as marked at the back of  
the power supply.  
Always ensure that when disconnecting and reconnecting your audio equipment the mains supply is switched  
off.  
Position the power lead and signal interconnects where they are not likely to be walked on or trapped by items  
placed on them.  
Do not use near water, or place water-filled containers on the X-LPS V8, for example, a flower vase or potted  
plants. If water does spill inside, immediately pull out the mains plug from the wall socket and inform  
your dealer, who should then check the unit before further use. Entry of liquid into the X-LPS V8 is  
dangerous, and may cause electric shock or fire hazard.  
Do not place the unit near direct heat sources such as radiators, direct sunlight or other equipment.  
Do not remove any covers or try to gain access to the inside. There are no internal adjustments or fuses you  
can replace yourself. Refer all service work to an authorised Musical Fidelity agent.  
Note: Unauthorised opening of the equipment will invalidate any warranty claim.  
Dust regularly with a soft cloth or soft brush but be careful when using cleaning or polishing agents - they may  
harm the surface finish.  
The electronics in modern hi-fi equipment is complex and may, therefore, be adversely affected or damaged by  
lightning. For protection of the audio system during electrical storms, remove the mains plugs and disconnect any  
aerial lead.  
If after-sales service is required, to help the dealer identify the X-LPS V8 please quote the serial number located on the  
rear panel of the unit.  
Issue 1  
Page 3 of 10  
 
X-LPSV8  
ITEM DISPOSAL INFORMATION  
DISPOSAL  
AFVAL  
The crossed out wheeled bin label that appears on the  
back panel of the product indicates that the product must not be  
disposed of as normal household waste. To prevent possible harm  
to the environment please separate the product from other waste to  
ensure that it can be recycled in an environmentally safe manner.  
Please contact local government office or retailer for available  
collection facilities.  
Het label op de achterzijde van dit apparaat, een  
afvalbak op wielen met een kruis doorgehaald, geeft aan dat dit  
apparaat niet samen met gewoon huishoudafval mag worden  
weggegooid. Om mogelijke schade aan onze leefomgeving te  
voorkomen dient dit apparaat, gescheiden van gewoon  
huishoudelijk afval, te worden afgevoerd zodat het op een  
milieuvriendelijke manier kan worden gerecycled. Neem voor  
beschikbare inzamelplaatsen contact op met uw gemeentelijke  
reinigingsdienst of met uw elektronica leverancier.  
DISPOSITION  
La poubelle sur roulettes barrées X, qui apparaît en logo  
sur le panneau arrière du produit, indique que celui-ci ne doit pas  
être traité comme un déchet domestique commun. Afin de protéger  
l'environnement, ce produit électronique devra être géré  
séparément et donc recyclé selon les nouvelles normes  
Européennes Rohs concernant les déchets d'appareils électroniques.  
Prière de contacter les services concernés gouvernementaux ou  
votre point de vente pour l'élimination et l'enlèvement de déchets  
électroniques équipés de composants électroniques.  
HÄVITTÄMINEN  
Yliruksattua jäteastiaa kuvaava tarra tuotteen  
takalevyssä kertoo, että tuotetta ei saa käsitellä normaalina  
talousjätteenä. Ympäristön suojelemiseksi on tuote pidettävä  
erillään muusta jätteestä ja se on kierrätettävä ekologisesti  
kestävällä tavalla. Ota yhteyttä laitteen myyjään tai Pirkanmaan  
Ympäristökeskukseen lähimmän kierrätyskeskuksen löytämiseksi.  
AFSKAFNING  
DISPOSAL  
Logoet med en skraldespand med kryds over på bagsiden  
af apparatet indikerer at dette produkt ikke må kasseres som normal  
husholdningsaffald. For at forebygge mulig skade på miljøet, bedes  
De separere dette produkt fra andet affald, og sikre at det bliver  
genbrugt på en miljørigtig måde. Kontakt venligst de lokale  
myndigheder eller din forhandler for oplysning om nærmeste  
tilgængelige opsamlingssted for elektronikaffald.  
La etiqueta cruzada hacia fuera del compartimiento que  
aparece en el panel trasero del producto indica que el producto no  
se debe reciclarse como basura normal de la casa. Para prevenir  
daños posible al ambiente separe por favor el producto de otras  
basura para asegurarse de que puede ser reciclada de una manera  
ambientalmente segura. Entre en contacto por favor a su oficina  
gubernamental local o a su minorista para las instalaciones  
disponibles de la colección.  
∆ΙΑ∆ΙΚΑΣΙΑ ΑΠΟΡΡΙΨΗΣ  
ΤΟ  
ΣΗΜΑ  
ΜΕ  
ΤΟΝ  
∆ΙΑΓΕΓΡΑΜΜΕΝΟ  
RIFIUTI  
ΤΡΟΧΗΛΑΤΟ ΚΑ∆Ο ΑΠΟΡΡΙΜΑΤΩΝ ΣΤΗΝ ΠΙΣΩ ΟΨΗ  
ΤΟΥ ΜΗΧΑΝΗΜΑΤΟΣ  
L'etichetta del cassonetto barrato riportato sul retro  
dell'apparecchio indica che il prodotto non deve essere smaltito  
tramite la procedura normale di smaltimento dei rifiuti domestici.  
Per evitare eventuali danni all'ambiente, separare questo prodotto  
da altri rifiuti domestici in modo che possa venire riciclato in base  
alle procedure di rispetto ambientale. Per maggiori dettagli  
sulle aree di raccolta disponibili, contattate l'ufficio govenativo  
locale od il rivenditore del prodotto.  
∆ΗΛΩΝΕΙ ΟΤΙ ΤΟ ΠΡΟΙΟΝ ΑΥΤΟ ∆ΕΝ ΠΡΕΠΕΙ ΝΑ  
∆ΙΑΧΕΙΡΙΣΘΕΙ ΣΑΝ ΣΥΝΗΘΙΣΜΕΝΟ ΟΙΚΙΑΚΟ ΑΠΟΒΛΗΤΟ.  
ΠΡΟΣ ΑΠΟΦΥΓΗ ΕΝ∆ΕΧΟΜΕΝΗΣ ΕΠΙΒΑΡΥΝΣΗΣ ΤΟΥ  
ΠΕΡΙΒΑΛΛΟΝΤΟΣ, ΞΕΧΩΡΙΣΤΕ ΤΟ ΠΡΟΙΟΝ ΑΠΟ ΤΑ  
ΑΛΛΑ  
ΑΠΟΡΡΙΜΑΤΑ ΩΣΤΕ ΝΑ ΕΞΑΣΦΑΛΙΣΘΕΙ Η ΑΝΑΚΥΚΛΩΣΗ  
ΤΟΥ ΜΕ ΤΟΝ ΠΡΕΠΟΝΤΑ ΤΡΟΠΟ.  
ΠΑΡΑΚΑΛΟΥΜΕ ΝΑ ΕΠΙΚΟΙΝΩΝΗΣΕΤΕ ΜΕ ΤΗΝ ΤΟΠΙΚΗ  
FACHGERECHTE ENTSORGUNG:  
ΥΠΗΡΕΣΙΑ ΑΝΑΚΥΚΛΩΣΗΣ  
Η
ΜΕ ΤΟ ΚΑΤΑΣΤΗΜΑ  
Das auf der Geräterückseite angebrachte Label deutet  
darauf hin, dass das Produkt nicht mit konventionellem  
Hauskehricht entsorgt werden darf. Um Schäden und  
Verschmutzungen an Umwelt und Mensch zu vermeiden, muss das  
Produkt fachgerecht entsorgt und von anderem Abfall getrennt  
werden. Wenden Sie sich bei Fragen hierzu an Ihren Fachhändler  
oder an eine öffentliche Informationsstelle.  
ΑΓΟΡΑΣ ΓΙΑ ΠΕΡΙΣΣΟΤΕΡΕΣ ΛΕΠΤΟΜΕΡΕΙΕΣ.  
Issue 1  
Page 4 of 10  
 
X-LPSV8  
INSTALLATION  
INTRODUCTION  
POWER CONNECTIONS  
Congratulations on the purchase of the new X-LPS V8 phono  
preamp. Great attention has been paid to internal layout,  
isolating each circuit section to prevent possible interaction.  
The unit features our highly refined low noise input amplifier  
circuit coupled with a low output impedance close tolerance  
RIAA stage to improve record delivery and dynamics. Two  
types of cartridge are catered for, moving magnet and moving  
coil, to allow full choice in selecting preferred cartridge type  
for the system.  
The X-LPS V8 requires a free mains socket for its power  
supply. The power supply then connects using its flying lead  
to the DIN 24V AC socket at the back of the unit. We advise  
that you use only the supplied X-series adaptor for this unit,  
or a suitable Musical Fidelity power supply.  
AUDIO CONNECTIONS  
Inputs: Connect turntable cartridge input to RCA MM or MC  
inputs as required.  
(see p.7 For more information). Use good quality fully  
connected (signal and ground) coaxial phono cables for all  
signal connections.  
The resultant performance achieved by this unit is among the  
best in the world. It has excellent signal to noise ratio, low  
distortion, wide bandwidth, huge dynamic range,  
extraordinary resolution and fine detail.  
Grounding post: Connect turntable ground lead (if present)  
to green earthing post. The post accepts bare wire, spade  
connectors or 4mm banana plugs.  
NB grounding apparatus in a system can sometimes  
aggravate rather than alleviate hum; some experimentation  
may be necessary to obtain ultimate noise levels. Remember  
especially with MC input, the X-LPS V8 is an extremely  
sensitive amplifier!  
CLEANING  
Before cleaning the unit, switch off power at the mains switch  
and remove the mains plug from the wall socket.  
Clean the cabinet and remote control unit using a moist cloth.  
Using solvents, white spirit or thinners is not advised, as they  
could damage the surface finish.  
INSTALLATION  
Outputs: Connect output sockets to a LINE level input e.g.  
AUX input on the amplifier/preamplifier.  
The X-LPS V8 outputs provide a highly amplified LINE level  
signal and MUST NOT be connected to a PHONO input  
Position the X-LPS V8 on a stable, horizontal surface where  
there is no risk of it being knocked, or subjected to vibration  
such as from loudspeakers.  
The X-LPS V8 must be protected from humidity - if the unit  
is moved from a cold place to a warm room, leave the unit for  
an hour or so to allow sufficient time for the moisture to  
evaporate.  
Issue 1  
Page 5 of 10  
 
X-LPSV8  
1. POWER LED  
2
FACILITIES AND CONNECTION  
UNIT FRONT PANEL  
1
UNIT REAR PANEL  
3
4
5
6
7
2. EARTH 4mm banana post  
3. MM/MC Switch  
5. MC INPUT RCA sockets  
6. OUTPUT RCA sockets (line level)  
4. MM INPUT RCA sockets  
7. POWER SUPPLY Input din socket  
Issue 1  
Page 6 of 10  
 
X-LPSV8  
AMPLIFIER OPERATION  
STARTING  
Once all connections are made, the power LED on the  
front panel will light, indicating unit is ready for use.  
PHONO IN (MM)  
To use the phono input connect MM cartridge to MM  
input. Press back panel switch to the MM position (out).  
PHONO IN (MC)  
To use the phono input connect MC cartridge to MC  
input. Press back panel switch to the MC position (in).  
IN USE  
The X-LPS V8 has been designed to be left on  
indefinitely, but please note the mains adaptor may  
become warm to the touch, this is normal.  
If switching the X-LPS on or off or changing the  
MM/MC switch, please ensure the volume is turned  
down on the following amplifier. This will avoid  
unwanted noises in the speaker due to the high  
sensitivity of the X-LPS V8.  
Issue 1  
Page 7 of 10  
 
X-LPSV8  
AMPLIFIER PROBLEMS?  
Basic problem-solving with an amplifier is similar to troubleshooting other electrical or electronic equipment. Always  
check the most obvious possible causes first, such as the following examples:  
Problem  
Probable Cause  
Remedy  
Plug in securely  
No power  
No sound  
Mains power supply is not fully  
inserted into mains socket  
Mains power supply lead is not fully  
inserted into rear socket  
Wrong connections between input  
sources and the unit  
Check audio input lead connections  
Check cartridge wiring  
Cartridge incorrectly wired  
Sound is not precise, lacking in bass  
and stereo image  
Cartridge incorrectly wired  
Double-check cartridge wiring using  
cartridge and turntable  
manuals/wiring diagrams.  
Input connector plugs not fully  
pushed in  
Check plugs are inserted fully and  
securely  
Output connector plugs not fully  
pushed in  
Hum  
Turntable not earthed and needs  
earthing  
Check turntable earthing lead is  
connected to earthing post on XLPS  
V8  
Disconnect Earthing lead from  
earthing post  
Turntable already earthed and makes  
hum loop in system  
Insert plug securely  
Audio connector plug not fully  
pushed in  
Check cable is connected at both  
ends.  
Cable Fault  
N.B. some esoteric cables have  
internal wiring intentionally  
disconnected/modified. For best  
results on all inputs AND outputs,  
please use good quality screened  
coax; fully connected signal-to signal,  
screen-to-screen.  
Unsuitable Cable  
(e.g. cable grounds not connected)  
Plop Heard in speakers when  
switching on or off or changing  
MM/MC switch  
High gain of XLPS V8 amplifying  
circuit transients.  
Not a fault.  
Please ensure volume level on  
amplifier is turned down if switching  
the XLPS V8 on or off or changing  
cartridge type switch whilst  
connected.  
If none of these actions affect a cure, please contact the dealer, or an authorised Musical Fidelity service agent.  
Remember; never open the case of the X-LPS V8, as this will invalidate the guarantee.  
Issue 1  
Page 8 of 10  
 
X-LPSV8  
AMPLIFIER SPECIFICATIONS  
MM input:  
Input response:  
RIAA/IEC combined, see graph  
Input sensitivity  
Input impedance  
3mV for 350mV out  
47K Ohms  
THD + N, 1KHz, 350mV out  
Overload margin  
<0.01% typical  
28dB  
Signal/noise ratio  
>100dB ‘A’-weighted  
MC input:  
Output:  
Input response:  
Input sensitivity  
Input impedance  
THD + N, 1KHz, 350mV out  
Overload margin  
RIAA/IEC combined, see graph  
350µV for 350mV out  
100 Ohms  
<0.01% typical  
28dB  
Signal/noise ratio  
>100dB ‘A’-weighted  
Pre-out impedance  
RIAA accuracy  
50 Ohms  
±0.25 dB 20Hz to 20KHz  
2 0 .0  
1 5 .0  
1 0 .0  
5 .0  
P H O N O R E S P O N S E  
0 .0  
d B  
RIA A  
- 5 .0  
P HO NO  
RIA A /IEC  
- 1 0 .0  
- 1 5 .0  
- 2 0 .0  
2 0 .0  
3 1 .5  
5 0 .0  
8 0 .0  
1 2 5  
2 0 0  
3 1 5  
5 0 0  
1 0 0 0  
1 6 0 0  
2 5 0 0  
4 0 0 0  
6 3 0 0 1 0 0 0 0 1 6 0 0 0  
F re q u e n c y (H z )  
Nominal phono response  
Connections:  
Moving magnet  
input:  
1 pairs MM level RCA connectors,  
Moving coil input:  
Line level outputs:  
Earth post:  
1 pairs MC level RCA connectors,  
1 pair RCA line level fixed RIAA  
1 4mm banana plug/binding posts  
Power  
requirement:  
12-0-12V (24V total) Using mains adaptor (supplied)  
AC at 500mA  
Standard  
Power Supply Unit  
T48A-24-500-3  
1 off  
accessories:  
Dimensions:  
Weight:  
Main unit  
180 mm 7 inches  
88 mm  
240 mm 9 ½ inches  
Wide  
High including feet  
Deep including terminals  
3 ½ inches  
1.55 kg, 3 ½ lbs  
Unboxed  
2.15 kg  
4 ¾ lbs  
Boxed unit including power supply and all accessories  
Musical Fidelity reserves the right to make improvements which may  
result in specification or feature changes without notice.  
Issue 1  
Page 9 of 10  
 
X-LPSV8  
MANUAL REVISION  
RELEASE  
DATE  
CHANGES  
Issue 1  
30th October 2007  
Issue 1  
Page 10 of 10  
 

Miele Cooktop CS 1212 1 User Manual
Mr Coffee Coffeemaker 111571 User Manual
Multi Tech Systems Network Card MultiConnect Adapter User Manual
Nady Systems Stereo Amplifier TMP 1 MICPREAMP User Manual
NEC Computer Monitor PlasmaSync 3300 User Manual
Nike Fitness Equipment + IPOD User Manual
Omega Engineering Blower DVG64 User Manual
Onkyo CD Player DX 7222 User Manual
Oregon Laptop Ferrari Laptop User Manual
Panasonic Air Conditioner CS 1873KR User Manual