MCB 7270
Full-Featured Marine CB 27 MHz Radio
Operation Manual
NAVMAN
Contents
1 - General Information
5
5
6
1.1
1.2
FEATURES
SCREEN SYMBOLS AND MEANINGS
2 - Basic Operation
7
2.1
2.2
2.3
KEY FUNCTIONS
RESET TO FACTORY DEFAULTS
EXAMPLE SCREENS
7
10
10
10
10
11
11
11
12
12
12
13
13
13
14
15
16
16
17
18
2.3.1 Power Up Sequence Screens
2.3.2 Channel Band Selection Screens
2.3.3 Transmission Screen
2.3.4 Noise Rejection Selection Screens
2.3.5 Battery Voltage Screens
2.3.6 Priority Channel Screens (Australia)
2.3.7 ALL SCAN Mode Screens
2.3.8 Locked Out and Unlocked Channel Screens
2.3.9 Store Favourite Channels Screens
2.3.10 PSCAN Working Channel Screen
2.3.11 PSCAN Favourite Channel Screen
Appendix A - Technical Specifications
Appendix B - Troubleshooting
Appendix C - Radio Channels (Australia)
C.1
C.2
MARINE (MB) FREQUENCIES
LAND (CB) FREQUENCIES
Appendix D - How to Contact Us
4
NAVMAN MCB 7270 Marine CB 27 MHz Radio Operation Manual
1 - General Information
1.1 Features
Congratulations on your purchase and installation of a Navman MCB 7270 27MHz radio. It provides you
with the following useful features:
•
Marine band (MB) communications with a land band (CB) capability, with six favourite
channels (three for each band).
•
•
Large LCD screen with prominent (17mm high) channel display.
Special size, highlighted symbols for Tx (transmission), Rx (reception), and X (Channel
Lockout).
•
•
Powerful transmission output (4W maximum legal).
Adjustable brightness settings for the screen and keypad for easy use in all
lighting conditions - including night time and bright sunlight.
•
•
•
•
•
Adjustable backlighting for the microphone.
Long cable for the microphone (2.3m when comfortably stretched).
Extension cable with jack, for connection to an external speaker.
Top centred PTT button for comfortable left- or right-handed use.
Quick access keys on the microphone for easy selection of channels (+/-), priority channels
(88/9), local mode (LOC) and favourite channel functions (3CH).
•
•
•
•
Channel 88/9 Priority/Distress key on the radio unit and microphone.
Special 3CH key for easy selection of your three favourite channels.
Most recently used channel is remembered and displayed at power up.
PSCAN facility to scan the working channel and the priority channel, or the favourite
channel(s) and the priority channel (similar to a dual watch facility).
•
•
•
•
•
•
ALL SCAN mode with busy channel lockout facility.
Noise rejection can be activated from chassis or microphone.
Powerful external speaker (up to 4W).
Voltage indicator (and low battery warning) for the battery supplying the radio.
Waterproof and submersible to comply with JIS-7.
Meets AS4355 and AS4367 technical specifications.
5
NAVMAN MCB 7270 Marine CB 27 MHz Radio Operation Manual
1.2 Screen Symbols and Meanings
This simulation shows the location of all the symbols that may appear on the screen:
Symbol
Meaning
X
Channel is locked out (in ALL SCAN mode only).
Channel selected (big digits).
88
Tx
Rx
Transmitting on maximum power (PTT depressed).
The signal of the tuned channel is greater than the squelch setting and the audio
is not muted.
CH 123
PRI
Shows which of the three favourite channels, if any, are selected. Otherwise blank.
Priority Distress/Calling channel is selected.
BAT
Voltage (shown in big digits) of the battery supplying the radio. If the battery voltage
falls below 10.8V, BAT will flash continuously and the radio will sound a warning
beep.
LOC
REJ
Local mode for 10-12dB reduced receiver sensitivity.
Noise rejection is on.
CB
(Citizen Band) land radio band frequencies are selected.
(Marine Band) marine radio band frequencies are selected.
The radio is in scanning mode (four scanning modes are available).
MB
SCAN
SIGNAL
The signal strength of the received channel. The bars are always shown when the
radio is receiving. One bar indicates a very weak signal, eight bars indicates a very
strong signal. Note that the signal strength is not shown for transmissions.
6
NAVMAN MCB 7270 Marine CB 27 MHz Radio Operation Manual
2 - Basic Operation
2.1 Key Functions
Note that some of the keys on the radio
chassis are duplicated on the microphone for
your convenience.
The PTT button and the LOC button are
available only on the microphone.
Key
Function
VOL/PWR
Volume and Power knob. Turn clockwise (right) to turn the radio on. Continue to
turn until a comfortable volume is reached. VOL/PWR also adjusts the settings of
an external speaker, if connected.
The screen displays the most recent channel, channel band, and noise rejection
setting. See Section 2.3.1 for an example.
Turn fully anti-clockwise (left) until the knob clicks to turn the radio off.
7
NAVMAN MCB 7270 Marine CB 27 MHz Radio Operation Manual
SQL
Squelch or Threshold Level knob. Sets the threshold level for the minimum
receiver signal.
Turn fully anti-clockwise (left) until random noise is heard, then turn slowly
clockwise (right) until the random noise disappears. Make another ¼ turn clockwise
for best reception in open sea conditions.
In areas of high noise (eg close to large cities) reception may improve if sensitivity is
reduced by turning SQL slowly clockwise (right). Also see REJ (noise rejection) and
LOC (Local mode) because these may also improve reception quality.
88/9
Priority Channel (Australia). Also on the microphone. Press to cancel all other
modes and tune into the priority channel (CH88 if MB is selected, or CH9 if CB
is selected). See Section 2.3.6 for an example. Press 88/9 again to return to your
original channel.
In countries other than Australia, consult your dealer about your local priority
channels.
BAND
3CH
Channel Band. Press to toggle between marine (MB) and land (CB) channel band
frequencies. The screen shows the selected channel band and radio tunes to the
most recently used channel in that channel band. See Section 2.3.2 for an example.
Appendix C shows the frequencies for each channel band.
Three Favourite Channels. Also on the microphone. You can store three favourite
channels for marine (MB) and another three favourites for land (CB) channel band
frequencies.
To store a favourite channel for the first time, select the channel band, then the
channel. Press and hold 3CH for at least 1.5 seconds to store it in the CH1 location.
Repeat the procedure to store two more favourite channels in the CH2 and CH3
locations respectively. See Section 2.3.9 for an example.
NOTE: If you try and add another favourite channel with 3 already stored,“FL”
shows in the display. You may store a new CH3 frequency only after deleting
the old one. CH1 and CH2 remain unless you delete them.
To select a favourite channel, select the channel band then press 3CH to toggle
between your favourite channels. The channel band and CH1, CH2, or CH3 are
displayed to show which favourite channel is currently selected.
To delete a favourite channel, select it then press and hold 3CH for at least 1.5
seconds until the CH1, CH2 or CH3 symbol disppears off the screen.
DIM
Backlighting. Press repeatedly to step through the settings (OFF, LOW, MED, HIGH)
until the desired backlight level is obtained.
SCAN
Scanning Mode. PSCAN and ALL SCAN modes are available on both land (CB) and
marine (MB) channel bands.
To scan one channel, select that channel then immediately press and release SCAN.
The radio goes into PSCAN mode; scanning the selected channel and automatically
checking the priority channel once every 4 seconds (like Dual Watch mode).
To scan one favourite channel, select that channel with 3CH then immediately
press and release SCAN. The radio goes into PSCAN mode; scanning the favourite
channel and automatically checking the priority channel once every 4 seconds
(like Dual Watch mode). See section 2.3.11 for an example.
8
NAVMAN MCB 7270 Marine CB 27 MHz Radio Operation Manual
To scan all three favourite channels, press 3CH then immediately press and hold
SCAN for at least 1.5 seconds. The radio goes into PSCAN mode; automatically
scanning the three favourite channels (and the priority channel once every 4
seconds). The screen shows the SCAN symbol, channel band, and the channel
being scanned.
To scan all channels within a channel band, select a channel that is not a favourite
then press and hold SCAN for at least 1.5 seconds. The radio goes into ALL SCAN
mode, automatically scanning about 7 channels per second (and the priority
channel once every 4 seconds). See Section 2.3.7 for an example.
To lock out an“always busy”channel when in ALL SCAN mode, press SKIP when the
radio stops at that channel, An X appears for one second on the screen to indicate
a locked out channel and then scanning resumes. Note that it is not possible to skip
over the priority channel. See Section 2.3.8 for an example.
When a signal is received in either PSCAN or ALL SCAN mode, scanning stops at
that channel. The screen shows Rx and the signal strength. If the signal ceases for
more than 4 seconds, the scan restarts.
To cancel scanning, press SCAN again. Note that pressing 88/9 (the priority
channel) also cancels scanning.
+ CH -
Channel Select. Also on the microphone. The current channel is shown on the
screen in big digits.
Press + or - repeatedly to step through the available channels one at a time, or
hold down to scroll rapidly through the available channels at about 7 channels per
second. See Appendix C for channel band frequencies.
REJ
Noise Rejection. Press REJ to activate the noise blanker circuit and reduce noise
(e.g. from the engine spark plugs or alternator). The screen shows REJ to indicate
that the noise blanker circuit is on. See Section 2.3.4 for an example.
LOC
Local Mode. Microphone only. Press to select Local mode. This reduces the receiver
sensitivity and noise. The screen shows LOC to indicate that Local mode is active.
Local mode can be useful in areas of high radio noise; for example, close to cities.
Local mode is not recommended for use in open sea conditions.
Press LOC again to return to normal sensitivity.
BAT
Battery Readout. Press BAT to display the voltage of the battery supplying the
radio in big digits on the screen; e.g.12.6V is displayed as 12, then after 1 second,
the display changes to .60. This cycle is repeated twice then the radio returns you
to the most recent mode. See Section 2.3.5 for an example.
SKIP
Lockout a Channel. You can use this only in ALL SCAN mode, if desired, to skip
over a channel that is always busy.
When the busy channel is displayed on the screen, press SKIP to lock it out. The
X symbol appears on the screen for one second by the channel number, then
scanning resumes. See Section 2.3.8 for an example. You can lock out a maximum
of 5 channels and the radio will remember them at startup.
9
NAVMAN MCB 7270 Marine CB 27 MHz Radio Operation Manual
If you are not in scanning mode and select a locked out channel, X is displayed by
the channel number on the screen. See Section 2.3.8 for an example.
To unlock a channel, press SCAN to exit from any scanning mode (if necessary),
select the locked out channel and then press SKIP. The X symbol disappears to
show the channel is no longer locked out. See Section 2.3.8 for an example.
PTT
Press To Talk. Microphone only. Press PTT to transmit at any time on an allowable
channel. This automatically stops scanning. See Section 2.3.3 for an example.
You must release PTT to receive a signal. If it sticks, a built-in timer will automatically
shut down a transmission after five minutes and sound the error beeps.
2.2 Reset to Factory Defaults
Use this to delete all your favourite channel settings, all your locked channels, and all your scan
settings.
1. Turn the radio off with VOL/PWR.
2. Press and hold both SCAN and SKIP while you turn the radio on with VOL/PWR.
The screen shows CL and the radio resets to the factory defaults.
2.3 Sample Screens
The following sections show typical screens and explain each example.
2.3.1 Power Up Sequence Screens
The left hand screen shows the startup screen that appears for 1.5 seconds after the radio is powered
up.
The startup screen is followed by a screen that shows the software version and then the most recent
settings. In this example, the radio tunes to channel (86) in the marine (MB) channel band. The radio is
receiving (Rx) at maximum signal strength.
Startup screen
Most recent settings
2.3.2 Channel Band Selection Screens
The left hand screen shows the radio set to receive (Rx) on the land (CB) channel band. The radio
tunes to the most recently used channel. Noise rejection (REJ) is on and the signal strength is shown
(SIGNAL).
The right hand screen shows the radio receiving on CH 86 in the marine (MB) channel band.
10
NAVMAN MCB 7270 Marine CB 27 MHz Radio Operation Manual
CB channel band
MB channel band
2.3.3 Transmission Screen
The screen shows a 4W transmission (Tx) being made on marine (MB) channel band, priority channel
88 (PRI).
The signal strength is not shown for transmissions
2.3.4 Noise Rejection Selection Screens
The left hand screen displays the REJ symbol, indicating that the noise blanker circuit is on and noise
reduction is active.
The right hand screen does not show REJ, meaning that the noise blanker circuit is off.
Noise rejection on
Noise Rejection Off
2.3.5 Battery Voltage Screens
The battery voltage (BAT) is shown in big digits over two screens. In this example, a battery voltage of
12.60V is displayed.
The first screen displays the battery symbol (BAT) and the whole volts (12) reading for one second. After
one second the next screen appears, showing BAT and the partial volts (.60) reading for one second.
This cycle is repeated twice.
Whole volts
Partial volts (note the decimal point)
11
NAVMAN MCB 7270 Marine CB 27 MHz Radio Operation Manual
2.3.6 Priority Channel Screens (Australia)
The left hand screen shows the radio receiving (Rx) on the marine (MB) channel band priority (PRI)
channel 88. The signal strength is at maximum, noise rejection mode (REJ) and local mode (LOC) are
selected.
The right hand screen shows the radio receiving on the land (CB) channel band priority (PRI) channel
09.
Priority channel 88
Priority channel 09
2.3.7 ALL SCAN Mode Screens
The left hand screen shows the radio in ALL SCAN mode (SCAN) for the marine (MB) channel band.
Noise rejection mode (REJ) and local mode (LOC) are selected.
The right hand screen shows the radio stopped in ALL SCAN mode (SCAN) to receive (Rx) on Channel
98 at the signal strength shown. The radio remains on this channel for 4 seconds and then resumes
scanning (unless you press SCAN to cancel the ALL SCAN mode and remain on that channel).
ALL SCAN mode
Receiving in ALL SCAN mode
2.3.8 Locked Out and Unlocked Channel Screens
The left hand screen shows the radio in normal mode when a locked out channel has been selected.
The X symbol appears next to the channel number to show that the channel is locked out.
To unlock the channel, just press SKIP and the X symbol disappears (right hand screen).
Locked Out (Normal)
Unlocked (Normal)
12
NAVMAN MCB 7270 Marine CB 27 MHz Radio Operation Manual
2.3.9 Store Favourite Channels Screens
The screens show three favourite channels being stored on the marine (MB) channel band; Channel
72 is favourite channel 1 (CH 1), channel 82 is favourite channel 2 (CH 2) and channel 86 is favourite
channel 3 (CH 3).
Three favourite channels can also be set for the land (CB) channel banks, giving a total of six stored
favourite channels.
Favourite CH 1
Favourite CH 2
Favourite CH 3
2.3.10 PSCAN Working Channel Screen
The screen shows the radio in PSCAN mode, set to scan (SCAN) one working channel on the marine
(MB) channel band while automatically checking the priority channel once every 4 seconds (just like
Dual Watch mode). Noise rejection mode (REJ) and local mode (LOC) are selected.
2.3.11 PSCAN Favourite Channel Screen
The screen shows the radio in PSCAN mode, set to scan (SCAN) favourite channel 1 (CH 1) on the
marine (MB) channel band while automatically checking the priority channel once every 4 seconds
(just like Dual Watch mode).
Scan CH 1
Scan priority channel
Return to CH 1
13
NAVMAN MCB 7270 Marine CB 27 MHz Radio Operation Manual
Appendix A - Technical Specifications
GENERAL
Compliance:
AS4355 and AS4367
Frequency range:
Frequency stability:
26.965 - 27.980 MHz
.001%
Phase locked loop
Dual Watch, Favourite 3 Channel Scan, All Scan
CH88/9 Recall
LCD display (viewing area):
LCD and microphone keys backlit
Backlighting control:
30 x 25 mm (black on silver)
4 levels (OFF, LOW, MED, HIGH)
Dimensions (without trunnion):
Weight (with microphone):
Waterproof level:
162 x 75 x 157mm
1.2kg
JIS-7
Built-in MCU Processor
Built-in Speech Processor circuitry
Last Channel memory
SO-239 Annenna connector:
Input voltage:
Operating temperature range:
Extension speaker cable with covered jack
50Ω
10.8 to 16.3V DC
0ºC to 55ºC
Fused DC power cable with quick disconnect terminals
Reverse polarity protection
TRANSMITTER
RF output power at 12.6V DC:
Modulator mode:
4W maximum legal power
AM (A3E)
Modulation sensitivity:
Hum & Noise:
Current drain:
60% modulation @ 1 Pascal (microphone)
Better than 10% @ 60% modulation
2.0 amps @ full modulation
Better than -65dB
Spurious & Harmonic Suppression:
RECEIVER
Dual Conversion Superhetrodyne
Sensitivity:
0.5uV for 12dB SINAD
IF frequencies:
Selectivity:
Image rejection:
Intermodulation rejection:
SQ range:
Audio output:
Current drain:
Spurious emissions:
Hum & Noise:
First: 10.7MHz; Second: 450KHz
-36dB @ ±6KHz, -60dB@±10KHz
70dB
60db (20KHz channel specification)
Tight = 10uV; Threshold = 0.3uV
1W @ 16Ω, external 4W @ 4Ω
800mA full volume, 350mA squelched
-57dBm
better than -50dB/1mV input
Specifications are subject to change without notice.
14
NAVMAN MCB 7270 Marine CB 27 MHz Radio Operation Manual
Appendix B - Troubleshooting
1. The radio will not power up.
A fuse may have blown OR there is no power getting to the radio unit.
a) Check the power cable for cuts, breaks, or squashed sections.
b) If the power cable is fine, replace the 3 Amp fuse (1 spare fuse is supplied).
c) Check the voltage of the battery that supplies the radio (see BAT in Section 2.1). It should be at
least 10.8V DC.
2. The radio unit blows the fuse when the power is switched on.
The power wires may have been reversed.
a) Check that the red wire is connected to the positive battery terminal, and the black wire is
connected to the negative battery terminal.
3. The speaker makes popping or whining noises when the engine is running.
Electrical noise may be interfering with the radio unit.
a) Re-route the power cables away from the engine.
b) Add a noise suppressor to the power cable.
c) Use resistive spark plug wires and/or use an alternator whine filter.
4. No sound from the external speaker.
a) Check that the external speaker cable is physically connected.
b) Check the soldering of the external speaker cable.
5. BAT flashes continuously and a warning beep sounds.
The power supply to the radio is too low.
a) Press BAT to check the voltage of the battery that supplies the radio (see BAT in Section 2.1). It
should be at least 10.8V DC.
b) Check the alternator on the vessel.
6. Poor reception or excessive noise interfering with the radio signal.
The radio sensitivity and noise elimination capabilities may need adjusting. Section 2.1 provides
basic information on adjusting squelch (SQL knob), noise rejection (REJ key) and local and normal
sensitivity (LOC key). However, if you continue to have problems, try the following sequence:
a) Ensure that LOC and REJ are both off (not shown on the LCD). Turn SQL to about halfway
between the minimum and maximum settings.
b) Turn SQL slowly clockwise (right) to reduce sensitivity. If this does not solve the problem, turn
SQL anticlockwise (left) to about halfway again and continue to the next step.
c) Press REJ to start noise rejection. Turn SQL slowly clockwise (right) to reduce sensitivity. If this
does not solve the problem, turn SQL anticlockwise (left) to about halfway again and continue
to the next step.
d) Press LOC to switch into Local mode and reduce the radio sensitivity and range. Turn SQL
slowly clockwise (right) to reduce sensitivity. If this does not solve the problem, the CB antenna
may need to be moved for optimum performance in situations where the interference source
cannot be isolated or eliminated.
7. F1 is displayed when trying to transmit.
The transmission power supply is too low or too high.
a) Press BAT to check the battery voltage (see BAT in Section 2.1 for more information if necessary).
It should be at least 10.8V DC.
b) Check the alternator on the vessel.
15
NAVMAN MCB 7270 Marine CB 27 MHz Radio Operation Manual
Appendix C - Radio Channels
The MCB 7270 radio is a marine band (MB) radio that includes a land band (CB) capability. The MCB
7270 radio should be installed in a boat and operated from a boat.
The marine band (MB) should be used to communicate with other boats and coast guard stations. The
land band (CB) should be used from the boat only to communicate with individuals or organisations
based on the land.
If you require a radio only for land-based communications, use a CB radio.
C.1 MARINE (MB) FREQUENCIES
CHANNEL
FREQUENCY
(MHz)
TRAFFIC TYPE
SHIP TO
SHIP
SHIP TO
SHORE
AUSTRALIA
27.680
68
72
82
86
Commercial & Charter. Calling and
working.
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
27.720
27.820
27.860
Professional fishing. Calling and
working.
Professional fishing. Calling and
working.
DISTRESS, safety and calling.
Supplementary to 27.880
88
90
27.880
27.900
DISTRESS, safety and calling.
Yes
No
Yes
Yes
Non-commercial clubs & groups only.
Calling and working.
91
94
96
98
27.910
27.940
27.960
27.980
Non-commercial clubs & groups only.
Calling and working.
No
Yes
Yes
Yes
Yes
Yes
No
Yes
Non-commercial club events. Calling
and working.
Non-commercial organisations. Calling
and working.
Recognised Rescue Organisations (eg
Surf Rescue). Calling and working.
16
NAVMAN MCB 7270 Marine CB 27 MHz Radio Operation Manual
C.2 LAND (CB) FREQUENCIES
Note 1: Do not transmit on CH16.
(CH16 should be used only for
a listening watch because it is
reserved for transmissions that
use SSB, not AM).
CB CHANNEL
FREQUENCY (MHz)
AUSTRALIA
26.965
1
2
26.975
3
26.985
4
27.005
5
27.015
6
27.025
7
27.035
8
27.055
9
27.065 (Emergency)
27.075
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
27.085 (Calling)
27.105
27.115
27.125
27.135
27.155 (see Note 1)
27.165
27.175
27.185
27.205
27.215
27.225
27.255
27.235
27.245
27.265
27.275
27.285
27.295
27.305
27.315
27.325
27.335
27.345
27.355
27.365
27.375
27.385
27.395
27.405
17
NAVMAN MCB 7270 Marine CB 27 MHz Radio Operation Manual
Appendix D How to contact us
Holland
NORTH AMERICA
Mexico
Thailand
BNT - Marine Electronics
30 Sudbury Rd, Acton, MA 01720.
Toll Free: +1 866 628 6261
Fax: +1 978 897 8264
e-mail: [email protected]
web:www.navman.com
Mercury Marine de Mexico
Anastacio Bustamente #76
Interior 6 Colonia Francisco Zarabia, Muang, Samutsakhon 74000, Thailand.
Zapapan, Jalisco, C.P. 45236 Mexico.
Ph: +52 33 3283 1030
Fax: +52 33 3283 1034
Thong Electronics (Thailand) Co. Ltd.
923/588 Ta Prong Road, Mahachai,
Navimo Holland
Industrieweg 4,
2871 JE Schoonhoven.
Ph: +31 182 320 522
Fax: +31 182 320 519
e-mail: [email protected]
United Kingdom
Navimo UK
Ph: +66 34 411 919
Fax: +66 34 422 919
e-mail: [email protected]
Uruguay
OCEANIA
Australia
Navman Australia Pty. Limited
Suite 2, 408 Victoria Road
Gladesville NSW 2111, Australia.
Ph: +61 2 9879 9000
Fax: +61 2 9879 9001
e-mail: [email protected]
Vietnam
HaiDang Co. Ltd.
Alvaro Bermudez, Nautica
11300 Montevideo, Uruguay.
Ph & Fax: +59 82 628 6562
e-mail: [email protected]
Hamilton Business Park
Bailey Road, Hedge End
Southhampton, Hants S030 2HE.
Ph: +44 01489 778 850
Fax: +44 0870 751 1950
e-mail: [email protected]
Sweden, Denmark, Finland and
Norway
763 Le Hong Phong St. Ward 12
District 10, Hochiminh City, Vietnam
Ph: +84 8 863 2159
ASIA
China
Fax: +84 8 863 2524
e-mail: [email protected]
Peaceful Marine Electronics Co. Ltd.
Guangzhou, Hong Kong, Dalian,
Qingdao, Shanghai
New Zealand
Absolute Marine Ltd.
MIDDLE EAST
Lebanon and Syria
Balco Stores
Unit B, 138 Harris Road,
East Tamaki, Auckland.
Ph: +64 9 273 9273
Fax: +64 9 273 9099
1701 Yanjiang Building
195 Yan Jiang Zhong Rd. 510115
Guangzhou, China.
Ph: +86 20 3869 8839
Fax: +86 20 3869 8780
e-mail: [email protected]
Navimo Nordic
Lundenvägen 2,
473 21 Henån.
Ph: +46 304 360 60
Fax: +46 304 307 43
e-mail:[email protected]
Balco Building, Moutran Street,
Tripoli (via Beirut). - Lebanon
P.O. Box: 622.
Ph: +961 6 624 512
Fax: +961 6 628 211
e-mail: [email protected]
Papua New Guinea
Lohberger Engineering,
Lawes Road, Konedobu.
PO Box 810, Port Moresby.
Ph: +675 321 2122
India
Spain
United Arab Emirates
Access India Overseas Pvt. Ltd.
A-98, Sector 21,
Navimo España
Kuwait, Oman, Iran, Saudi
Arabia, Bahrain and Qatar
Abdullah Moh’d Ibrahim Trading, opp
Creak Rd. Baniyas Road, Dubai.
Ph: +971 4 229 1195
Polígono Industrial de Cabrera
Plaza Industria, S/N
08349 Cabrera de Mar
Barcelona.
Ph: +34 93 750 75 04
Fax: +34 93 750 75 34
e-mail: [email protected]
Fax: +675 321 2704
e-mail: [email protected]
Noida - 201 301, India.
Ph: +91 120 244 2697
TeleFax: +91 120 253 7881
Mobile: +91 98115 04557
e-mail: [email protected]
LATIN AMERICA
Fax: +971 4 229 1198
Argentina
e-mail: [email protected]
Costanera Uno S.A.
Esmario Export Enterprises
AFRICA
South Africa
Av Pte Ramón S. Castillo y Calle 13
Zip 1425 Buenos Aires, Argentina.
Ph: +54 11 4312 4545
Fax +54 11 4312 5258
e-mail:
Block No. F-1, 3rd Floor, Surya Towers
Sardar Patel Rd, Secunderbad 500 003.
Ph: +91 40 2784 5163
Fax: +91 40 2784 0595
e-mail: [email protected]
Portugal
Pertec (Pty) Ltd (Coastal Division)
16 Paarden Eiland Road.
Paarden Eiland, 7405
PO Box 527,
Navimo Portugal
Avenida de India N°40
1300-299 Lisbon.
Ph: +351 21 362 04 57
Fax: +351 21 362 29 08
e-mail: [email protected]
Other countries in Europe
Plastimo International
Paarden Eiland, 7420
Cape Town, South Africa.
Ph: +27 21 508 4707
Fax: +27 21 508 4888
e-mail: [email protected]
Korea
Brazil
Kumhomarine Technology Co. Ltd.
#604-842, 2F, 1118-15, Janglim1-Dong,
Saha-Gu, Busan, Korea.
Equinautic Com Imp Exp de Equip
Nauticos Ltda.
Rua Ernesto Paiva, 139
Clube dos Jangadeiros
Porto Alegre - RS - Brasil
CEP: 91900-200.
Ph: +55 51 3268 6675
+55 51 3269 2975
Fax: +55 51 3268 1034
e-mail:
Ph: +82 51 293 8589
Fax: +82 51 265 8984
e-mail: [email protected]
Maldives
Maizan Electronics Pte. Ltd.
Henveyru, 08 Sosunmagu.
Male', Maldives.
Mobile: +960 78 24 44
Ph: +960 32 32 11
Fax: +960 32 57 07
e-mail: [email protected]
15, rue Ingénieur Verrière BP435
56325 Lorient Cedex, France.
Ph: +33 2 97 87 36 59
Fax: +33 2 97 87 36 29
e-mail:
HEADQUARTERS
Navman NZ Limited
13-17 Kawana St.
Northcote.
EUROPE
France, Belgium and Switzerland
Plastimo International
15, rue Ingénieur Verrière,
BP435,
56325 Lorient Cedex.
Ph: +33 2 97 87 36 36
Fax: +33 2 97 87 36 49
e-mail: [email protected]
Realmarine
Estrada do Joa 3862,
Germany
Barra da Tijuca, Rio de Janeiro, Brazil.
CEP: 22611-020.
Ph: +55 21 2483 9700
Fax: +55 21 2495 6823
e-mail: [email protected]
Singapore and Malaysia, Brunei,
Indonesia and Phillipines
RIQ PTE Ltd.
Blk 3007, 81 Ubi Road 1, #02-440,
Singapore 408701.
Ph: +65 6741 3723
Fax : +65 6741 3746
P.O. Box 68 155,
Newton,
Auckland,
New Zealand.
Ph: +64 9 481 0500
Fax: +64 9 481 0590
e-mail: [email protected]
Navimo Deutschland
15, rue Ingénieur Verrière
BP435- 56325 Lorient Cedex.
Ph: +49 6105 92 10 09
+49 6105 92 10 10
+49 6105 92 10 12
Fax: +49 6105 92 10 11
e-mail:
Chile
Equimar
e-mail: [email protected]
Manuel Rodrigurez 27
Santiago, Chile.
Ph: +56 2 698 0055
Fax +56 2 698 3765
e-mail: [email protected]
Taiwan
Seafirst International Corporation
No. 281, Hou-An Road, Chien-Chen
Dist. Kaohsiung, Taiwan R.O.C.
Ph: +886 7 831 2688
Italy
Navimo Italia
Nuova Rade spa, Via del Pontasso
16015 Casella Scrivia (GE).
Ph: +39 1096 80162
5
Mera Vennik
Colon 1148, Talcahuano,
4262798, Chile.
Fax: +886 7 831 5001
e-mail: [email protected]
Fax: +39 1096 80150
Ph: +56 41 541 752
Fax +56 41 543 489
e-mail: [email protected]
e-mail: [email protected]
18
NAVMAN MCB 7270 Marine CB 27 MHz Radio Operation Manual
Designed in New Zealand
Made in China
MN000313A
NAVMAN
Lat 36° 48.404’S
N13408
|