User’s Guide
Shop online at
omega.com
e-mail: [email protected]
For latest product manuals:
omegamanual.info
USB-4750
32 Channel Isolated Digital I/O
USB Data Acquisition Module
USB-4750
32-Channel Isolated
Digital I/O USB Data Acquisition
Module
User Manual
Contents
Chapter 1 Introduction..................................................... 2
1.1 Hardware Features............................................................. 2
1.2 Software Overview............................................................ 3
1.2.1 More on the CD ............................................................. 3
Chapter 2 Installation ....................................................... 6
2.1 Unpacking ......................................................................... 6
2.2 Driver Installation ............................................................. 7
2.3 Hardware Installation........................................................ 9
2.4 Hardware Uninstallation ................................................... 9
Figure 2.1:Unplug or Eject Hardware Dialog .............. 10
Figure 2.2:Stop a Hardware device dialog box ............ 10
Chapter 3 Signal Connections........................................ 12
3.1 Overview......................................................................... 12
3.2 I/O Connectors ................................................................ 12
3.2.1 Pin Assignments .......................................................... 12
Figure 3.1:I/O Connector Pin Assignment .................. 12
3.2.2 I/O Connector Signal Description ................................ 13
Table 3.1:I/O Connector Signal Descriptions .............. 13
3.2.3 LED Indicator Status Description ................................ 13
Table 3.2:LED Indicator Status Description ................ 13
3.3 Isolated Digital I/O Connections..................................... 14
3.3.1 Dry/Wet Contact Support for Digital Input ................. 14
Figure 3.2:Isolated Digital Input Connections ............. 14
3.3.2 Isolated Digital Output Connections ............................ 15
Figure 3.3:Isolated Digital Output Connections .......... 15
3.4 Field Wiring Considerations ........................................... 16
Appendix A Specifications ................................................. 18
A.1 Isolated Digital Input....................................................... 18
A.2 Isolated Digital Output.................................................... 18
A.3 Isolated Counter .............................................................. 18
A.4 General ............................................................................ 18
v
Table of Contents
USB-4750 User Manual
vi
1
2
Introduction
Sections include:
•
•
Hardware Features
Software Overview
Chapter 1 Introduction
Thank you for buying the USB-4750 data acquisition mod- ule. The
USB-4750 is a powerful data acquisition (DAS) module for the USB port.
It features a unique circuit design and complete functions for data
acquisition and control.
1.1 Hardware Features
USB-4750 features excellent measurement & control functions:
•
•
•
•
•
•
•
•
32 isolated digital input/output channels
High-voltage isolation up to 2,500 VDC on all channels
Dry/wet contact support
Interrupt handling capability
High-sink current for isolated output channels (100mA max./Channel)
Digital output value retained after hot system reset
Programmable Power-Up States for output channels
Wiring ternimals on module
Note:
You can install up to sixteen USB-4750’s to a
system because of the restriction of device
BoardID
Note:
The power output of an USB port is 500 mA,
while the USB-4750 requires 350 mA (Max.).
This means that if an USB hub is used, it will
need an external power supply to support more
than one USB-4750 device.
Note:
For detailed specifications of USB-4750, please
refer to Appendix A, Specifications.
USB-4750 User Manual
2
1.2 Software Overview
Omega offers a rich set of DLL drivers, third-party driver support and
application software on the companion CD-ROM to help fully exploit the
functions of your device. The Device Drivers feature a complete I/O
function library to help boost your application performance and work
seamlessly with development tools such as Visual C++, Visual Basic,
1.2.1 More on the CD
For instructions on how to begin programming in each development tool,
some tutorial chapters are included in the Device Drivers Manual for your
reference. Please refer to the corresponding sections in these chapters on
the Device Drivers Manual to begin your programming efforts. You can
also look at the example source code provided for each programming tool,
since they can get you very well oriented.
The Device Drivers Manual can be found on the companion CD-ROM.
Alternatively, if you have already installed the Device Drivers on your
system, The Device Drivers Manual can be readily accessed through the
Start button:
Start/Programs/Omega USB-4700 Series/ Device Driver’s Manual
The example source code can be found under the corresponding installa-
tion folder such as the default installation path:
Program Files/Omega/USB-4700/Examples
3
Chapter1
USB-4750 User Manual
4
2
2
Installation
Sections include:
•
•
•
•
Unpacking
Driver Installation
Hardware Installation
Hardware Uninstallation
Chapter 2 Installation
2.1 Unpacking
After receiving your USB-4750 package, please inspect its contents first.
The package should contain the following items:
•
•
•
USB-4750 Module
Shielded USB 2.0 Cable (1.8 m)
Companion CD-ROM (DLL driver included)
The USB-4750 Module harbors certain electronic components vulnerable
to electrostatic discharge (ESD). ESD could easily damage the integrated
circuits and certain components if preventive measures are not carefully
paid attention to. Before removing the module from the antistatic plastic
bag, you should take following precautions to ward off possible ESD
damage:
•
Touch the metal part of your computer chassis with your hand to dis-
charge static electricity accumulated on your body. One can also use a
grounding strap.
•
Make contact between the antistatic bag and ground before opening.
After taking out the module, you should first:
Inspect the module for any possible signs of external damage (loose or
damaged components, etc.). If the module is visibly damaged, please
notify our service department or our local sales representative immedi-
ately. Avoid using a damaged module with your system.
•
Avoid physical contact with materials that could hold static
electricity such as plastic, vinyl and Styrofoam.
USB-4750 User Manual
6
2.2 Driver Installation
We recommend you install the software driver before you install the
USB-4750 module into your system, since this will guarantee a smooth
installation process.
The 32-bit DLL driver Setup program for the USB-4750 module is
included on the companion CD-ROM that is shipped with your module
package. Please follow the steps on the following page to install the
driver software:
7
Chapter2
For further information on driver-related issues, an online version of the
Device Drivers Manual is available by accessing the following path:
Start/Programs/Omega USB-4700 Series/ Device Driver’s Manual
USB-4750 User Manual
8
2.3 Hardware Installation
Note:
Make sure you have installed the software driver
before you install the module (please refer to Sec-
tion 2.2 Driver Installation)
After the DLL driver installation is completed, you can now go on to
install the USB-4750 module in any USB port that supports the
USB 1.1/2.0 standard, on your computer. It is suggested that you refer to
the computer’s user manual if you have any doubts. Please follow the
steps below to install the module on your system.
Step 1: Touch the metal part on the surface of your computer to neutral-
ize the static electricity that might be in your body.
Step 2: Plug your USB module into the selected USB port. Use of exces-
sive force must be avoided; otherwise the module might get damaged.
Note:
In case you installed the module without installing the
DLL driver first, Windows 2000/XP will recognize your
module as an “unknown device” after reboot, and will
prompt you to provide necessary driver. You should
ignore the prompting messages (just click the Cancel
button) and set up the driver according to the steps
described in Section 2.2 Driver Installation.
After your module is installed, you can configure it using the Device
Manager. The Device Driver's Manual can be found at:
Start/Programs/Omega USB-4700 Series/ Device Driver’s Manual
2.4 Hardware Uninstallation
Though the USB modules are hot swappable, we still recommend you to
follow the hardware un-installation procedure to avoid any unpredictable
damages to your device or your system.
Step1: Close the applications of the USB module.
9
Chapter2
Step2: Right click the “Unplug or Eject Hardware” icon on your task bar.
Figure 2.1: Unplug or Eject Hardware Dialog
Step3: Select “USB-4750 Device” and press “Stop” Button.
Figure 2.2: Stop a Hardware device dialog box
Step4: Unplug your USB device from the USB port.
Note: Please make sure that you have closed the application
before unplugging the USB device, otherwise unexpected
system error or damage may occur.
USB-4750 User Manual
10
3
2
Signal Connections
Sections include:
•
•
•
Overview
Isolated Digital I/O Connections
Field Wiring Considerations
Chapter 3 Signal Connections
3.1 Overview
Maintaining good signal connections is one of the most important factors
in ensuring that your application system is sending and receiving data
correctly. A good signal connection can avoid unnecessary and costly
damage to your PC and other hardware devices.
3.2 I/O Connectors
USB-4750 is equipped with plug-in screw-terminal connectors that facili-
tate connection to the module without terminal boards or cables.
3.2.1 Pin Assignments
Figure 3.1: I/O Connector Pin Assignment
Note:
IDI0 shares the same pin with INT0
IDI4 shares the same pin with INT0_G
IDI7 shares the same pin with CNT0
IDI8 shares the same pin with INT1
IDI12 shares the same pin with INT1_G
IDI15 shares the same pin with CNT1
USB-4750 User Manual
12
3.2.2 I/O Connector Signal Description
Table 3.1: I/O Connector Signal Descriptions
Signal
Reference Direction
Description
IDI<0~15>
INT<0,1>
GND
INT_G
-
Input
Input
-
Isolated digital input channels
Interrupt trigger sources.
Ground for interrupt pins.
INT<0,1>_
G
CNT<0,1>
GND
Input
Output
-
Isolated input counters
IDO<0~15> GND
Isolated digital output channels
COM<0,1>
-
Common pins for connecting induc-
tive loads of isolated output channels
GND
-
-
Ground
3.2.3 LED Indicator Status Description
The USB Module is equipped with a LED indicator to show the current
status of the device. When you plug the USB device into the USB port,
the LED indicator will blink five times and then stay lit to indicate that it
is on. Please refer to the following table for detailed LED indicator status
information.
Table 3.2: LED Indicator Status Description
LED Status
Description
On
Device ready for work
Device not ready to work
Device initialization
Device working
Off
Slow Blinking (5 times)
Fast Blinking
(Depends on data transfer speed).
13
Chapter3
3.3 Isolated Digital I/O Connections
3.3.1 Dry/Wet Contact Support for Digital Input
Each digital input channel accepts either dry contact or 0 ~ 5 VDC wet
contact inputs. Dry contact capability allows the channel to respond to
changes in external circuitry (e.g., the closing of a switch in the external
circuitry) when no voltage is present in the external circuit. Figure 3-1
shows external circuitry with both wet and dry contact components, con-
nected as an input source to one of the card's digital input channels.
Figure 3.2: Isolated Digital Input Connections
USB-4750 User Manual
14
3.3.2 Isolated Digital Output Connections
Each of 8 isolated digital output channels comes equipped with a Darling-
ton transistor. Every 8 output channels share common collectors and inte-
gral suppression diodes for inductive loads. Channels 0 ~ 7 use COM0,
and channels 8 ~ 15 use COM1 as a common pin. If an external voltage (5
~ 40 V) is applied to an isolated output channel (IDO 0 ~ IDO 15) while it
is being used as an output channel, the current will flow from the external
voltage source to the card. Please take care that the current through each
GND pin not exceed 100 mA.
Figure 3.3 shows how to connect an external output load to the card's iso-
lated outputs.
Figure 3.3: Isolated Digital Output Connections
15
Chapter3
3.4 Field Wiring Considerations
•
•
•
When you use USB-4750 to acquire data from outside, noises in the
environment might significantly affect the accuracy of your measure-
ments if due cautions are not taken. The following measures will be
helpful to reduce possible interference running signal wires between
signal sources and the USB-4750.
The signal cables must be kept away from strong electromagnetic
sources such as power lines, large electric motors, circuit breakers or
welding machines, since they may cause strong electromagnetic inter-
ference. Keep the analog signal cables away from any video monitor,
since it can significantly affect a data acquisition system.
If the cable travels through an area with significant electromagnetic
interference, you should adopt individually shielded, twisted-pair wires
as the analog input cable. This type of cable has its signal wires twisted
together and shielded with a metal mesh. The metal mesh should only
be connected to one point at the signal source ground.
•
•
Avoid running the signal cables through any conduit that might have
power lines in it.
If you have to place your signal cable parallel to a power line that has a
high voltage or high current running through it, try to keep a safe dis-
tance between them. Or place the signal cable in a right angle to the
power line to minimize the undesirable effect.
USB-4750 User Manual
16
A
2
Specifications
Appendix A Specifications
A.1 Isolated Digital Input
16
Channels
DI0, DI8
2500 VDC
25 µs
Interrupt Inputs
Optical Isolation
Opto-isolator ResponseTime
5~50VDC, or dry contact
Input Voltage
A.2 Isolated Digital Output
16
Channels
2500 VDC
Optical Isolation
Opto-isolatorResponse Time
Output Voltage
25µs
5 ~ 40 VDC
100mA/ch. Max. 1.1A/total Max.
Sink Current
A.3 Isolated Counter
2 independent
Channels
32-bit counters (low 16bit by hardware and high
16bit by firmware)
Resolution
External 8MHz max. 2 independent program-
Internal 20MHz max.
Base Clock
mable clock sources
Input frequency from 0.1Hz to 1Mhz
2 to 65535
Frequency Measurement
External Input Divide
A.4 General
10-pin screw terminal *4
132 X 80 X 32 mm (5.2” X 3.2” X 1.3”)
5 V @ 350 mA max.
I/O Connector Type
Dimensions
Power Consumption
Operation 0~60° C (32~140° F) (refer to IEC 68-2-1, 2)
Temperature
Storage
-20~70° C (-4~158° F)
5%~95% RH non-condensing (refer to IEC 68-2-1, 2)
Relative Humidity
USB-4750 User Manual
18
WARRANTY/DISCLAIMER
OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and
workmanship for a period of 13 months from date of purchase. OMEGA’s WARRANTY adds an
additional one (1) month grace period to the normal one (1) year product warranty to cover
handling and shipping time. This ensures that OMEGA’s customers receive maximum
coverage on each product.
If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer
Service Department will issue an Authorized Return (AR) number immediately upon phone or
written request. Upon examination by OMEGA, if the unit is found to be defective, it will be
repaired or replaced at no charge. OMEGA’s WARRANTY does not apply to defects resulting
from any action of the purchaser, including but not limited to mishandling, improper interfacing,
operation outside of design limits, improper repair, or unauthorized modification. This
WARRANTY is VOID if the unit shows evidence of having been tampered with or shows evidence
of having been damaged as a result of excessive corrosion; or current, heat, moisture or vibra-
tion; improper specification; misapplication; misuse or other operating conditions outside of
OMEGA’s control. Components in which wear is not warranted, include but are not limited to
contact points, fuses, and triacs.
OMEGA is pleased to offer suggestions on the use of its various products. However,
OMEGA neither assumes responsibility for any omissions or errors nor assumes liability
for any damages that result from the use of its products in accordance with information
provided by OMEGA, either verbal or written. OMEGA warrants only that the parts
manufactured by the company will be as specified and free of defects. OMEGA MAKES
NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER,
EXPRESSED OR IMPLIED, EXCEPT THAT OF TITLE, AND ALL IMPLIED WARRANTIES
INCLUDING ANY WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The remedies of pur-
chaser set forth herein are exclusive, and the total liability of OMEGA with respect to this
order, whether based on contract, warranty, negligence, indemnification, strict liability or
otherwise, shall not exceed the purchase price of the component upon which liability is
based. In no event shall OMEGA be liable for consequential, incidental or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as
a “Basic Component” under 10 CFR 21 (NRC), used in or with any nuclear installation or activity;
or (2) in medical applications or used on humans. Should any Product(s) be used in or with any
nuclear installation or activity, medical application, used on humans, or misused in any way,
OMEGA assumes no responsibility as set forth in our basic WARRANTY/DISCLAIMER language,
and, additionally, purchaser will indemnify OMEGA and hold OMEGA harmless from any liability
or damage whatsoever arising out of the use of the Product(s) in such a manner.
RETURN REQUESTS/INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department.
BEFORE RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN
AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER SERVICE DEPARTMENT
(IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number should then be
marked on the outside of the return package and on any correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to
prevent breakage in transit.
FOR WARRANTY RETURNS, please have
the following information available BEFORE
contacting OMEGA:
1. Purchase Order number under which
the product was PURCHASED,
2. Model and serial number of the product
under warranty, and
FOR NON-WARRANTY REPAIRS, consult
OMEGA for current repair charges. Have the
following information available BEFORE
contacting OMEGA:
1. Purchase Order number to cover the COST
of the repair,
2. Model and serial number of the product, and
3. Repair instructions and/or specific
problems relative to the product.
3. Repair instructions and/or specific problems
relative to the product.
OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible.
This affords our customers the latest in technology and engineering.
OMEGA is a registered trademark of OMEGA ENGINEERING, INC.
© Copyright 2007 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied,
reproduced, translated, or reduced to any electronic medium or machine-readable form, in whole or in part, without
the prior written consent of OMEGA ENGINEERING, INC.
Where Do I Find Everything I Need for
Process Measurement and Control?
OMEGA…Of Course!
Shop online at omega.com
TEMPERATURE
Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Thermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies
Wire: Thermocouple, RTD & Thermistor
Calibrators & Ice Point References
Recorders, Controllers & Process Monitors
Infrared Pyrometers
PRESSURE, STRAIN AND FORCE
Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Transducers & Strain Gages
Load Cells & Pressure Gages
Displacement Transducers
Instrumentation & Accessories
FLOW/LEVEL
Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Rotameters, Gas Mass Flowmeters & Flow Computers
Air Velocity Indicators
Turbine/Paddlewheel Systems
Totalizers & Batch Controllers
pH/CONDUCTIVITY
Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ pH Electrodes, Testers & Accessories
Benchtop/Laboratory Meters
Controllers, Calibrators, Simulators & Pumps
Industrial pH & Conductivity Equipment
DATA ACQUISITION
Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Data Acquisition & Engineering Software
Communications-Based Acquisition Systems
Plug-in Cards for Apple, IBM & Compatibles
Datalogging Systems
Recorders, Printers & Plotters
HEATERS
Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Heating Cable
Cartridge & Strip Heaters
Immersion & Band Heaters
Flexible Heaters
Laboratory Heaters
ENVIRONMENTAL
MONITORING AND CONTROL
Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Metering & Control Instrumentation
Refractometers
Pumps & Tubing
Air, Soil & Water Monitors
Industrial Water & Wastewater Treatment
pH, Conductivity & Dissolved Oxygen Instruments
M4569/0907
|