®
S I M P L Y
A M A Z I N G
USER’S GUIDE
XL2090RSM
COMMERCIAL
HIGH SPEED UPRIGHT VACUUM
CLEANER WITH
®
CLEANING SYSTEM
•IMPORTANT•
SAVE THIS BOOKLET!
Includes:
• Safety Warnings
• Warranty
• Operating Instructions
• Trouble Diagnosis
• Accessories
BEFORE OPERATING CLEANER,
READ ALL INSTRUCTIONS IN
THIS MANUAL CAREFULLY.
IMPORTANT SAFETY
INSTRUCTIONS
When using an electrical appliance, basic
precautions should always be followed,
including the following:
Table of Contents
READ ALL INSTRUCTIONS BEFORE
USING THIS VACUUM CLEANER
Maintenance and Customer Service, Accessories,
Grounding Instructions, Important Safety Instructions . . . . . . . page
2
WARNING
Warranty, Unit Specifications,Parts List,
Assembly, Operating Instructions . . . . . . . . . . . . . . . . . . . . . . page
To reduce the risk of fire,
electric shock, or injury:
3
4
5
General Information, To Replace Filter Dust Bag,
How to Replace a Worn Belt, To Adjust or Replace Brush . . . page
Using an Oreck Fresh Air® Tab, Stuffing or Blockage,
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page
• Do not leave appliance unattended when plugged in.
Unplug from outlet when not in use and before servicing.
• Do not use outdoors or on wet surfaces.
• Do not operate the unit while in the upright and locked
position.
• Do not let the unit run while in any one stationary position
for any period of time. Keep the unit moving while in
operation.
Maintenance and Customer Service
Your Oreck vacuum cleaner is a product of precise engineering. The
motor bearings are permanently lubricated and should not be oiled. If
you require additional information or have problems with your Oreck
appliance, you may call ORECK commercial customer service at:
1-800-989-1150
• Do not allow to be used as a toy. Close attention is
necessary when used by or near children.
• Use only as described in this manual. Use only
manufacturer’s recommended attachments.
• Do not use with damaged cord or plug. If appliance is not
working as it should, has been dropped, damaged, left
outdoors, or dropped into water, return it to a service
center or call commercial customer service at:
1-800-989-1150
Please specify the model number and serial/code number which can be
found on the data plate on the back of the vacuum.
Save your sales or purchase slip. Should your ORECK appliance require
warranty service in the U.S.A., present this slip to the Authorized Service
Center as your proof of purchase date.
• Do not pull or carry by cord, use cord as a handle, close
door on cord, or pull cord around sharp edges or corners.
Keep cord away from heated surfaces.
• Do not run appliance over cord.
• Do not unplug by pulling on cord. To unplug, grasp the
plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Do not put any object into openings. Do not use with any
opening blocked; keep free of dust, lint, hair and anything
that may reduce air flow.
Accessories (Sold Separately)
ITEM
1.
PART #
®
Dust Bag, 25 Pack, Saniseal
Hypo-Allergenic
Dust Bag, 25 Pack, Regular
Belts, 3 Pack
Oreck Fresh Air® Tabs
PK800025DW
PK800025
0300604
2.
3.
AIRTABS
• Keep hair, loose clothing, fingers and all parts of body
away from openings and moving parts.
• Do not use to pick up anything that is burning or smoking,
such as cigarettes, matches, or hot ashes.
• Do not use without filter bag assembly in place.
• Turn off all controls before unplugging.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible liquids,
such as gasoline or lighter fluid, or use in areas where
they may be present.
• Do not use appliance in an enclosed space where
flammable, explosive or toxic vapors are given off by oil
base paint, paint thinner, some mothproofing substances,
or in an area where flammable dust is present.
• Do not pick up toxic material such as chlorine bleach,
drain cleaner, gasoline, etc. with this appliance.
• Use caution when vacuuming over area rug edges and
fringe.
Grounding Instructions
This appliance must be grounded. If it should malfunction or break
down, grounding provides a safe path of least resistance for electrical
current, reducing the risk of electric shock. The cord for this appliance
has an equipment-grounding conductor and a grounding plug. It must
only be plugged into an electrical outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
DANGER: Improper connection of the equipment-grounding conductor
can result in a risk of electrical shock. Check with a qualified electrician
or service person if you are in doubt as to whether the outlet is
grounded. If not, have a proper outlet installed by a qualified electrician.
This appliance is for use on a nominal 120-volt circuit. It has a grounding
plug similar to the example shown.
Grounding Pin
Make sure the appliance is
connected to an outlet with the
same configuration as the plug.
No adapter should be used with
this appliance.
Grounded Outlet
SAVE THESE INSTRUCTIONS
For Commercial Use
2
Bag Cover: XL Filter Knit, heavy duty, reinforced. Convenient pocket in
Warranty
back for storage of cleaning accessories and extra disposable dust bag.
®
ORECK MANUFACTURING COMPANY: (Oreck gives you the following
limited warranty for this product only if it was originally purchased for
use, not resale, from Oreck or an Oreck Authorized Retail Dealer.)
MicroSweep : Cleans bare floors without hoses, adjustments, or
attachments.
Oreck will repair or replace, free of charge, to the original purchaser,
any part which is found to be defective in material or workmanship
within six (6) months of the date of purchase. This limited warranty
covers the revolving roller brush for thirty (30) days for commercial use
only.
Parts List
To assist you in identifying components of your vacuum, the parts have
been numbered as follows:
This limited warranty does not cover the replacement of expendable or
consumable parts such as carbon motor brushes, edge brushes, drive
belts, bulbs, disposable bags and other parts subject to normal wear
unless they are defective in material or workmanship.
This limited warranty does not apply to any part subjected to accident,
abuse, or alteration, misuse, damage caused by fire or act of God, the
use of voltages other than indicated on the serial number plate of this
product or service of this product by other than Oreck or an Oreck
Factory Authorized Service Center.
1
1
2
3
4
5
6
7
8
9
Handle section, upper
Tube, lower
11
9
Power head
13
Outer bag
Paper filter dust bag
Power cord
16
5
Retaining spring
Bag tension bar
Zip fastener
12
2
4
Oreck does not authorize any person or representative to assume or
grant any other warranty obligation with the sale of this product.
Oreck’s limited warranty is valid only if you retain proof of purchase
from Oreck or an Oreck Authorized Retail Dealer for this product. If you
purchase this product from any other source, your purchase is “AS IS,”
which means Oreck grants you no warranty, and that you, not Oreck,
assume the entire risk of the quality and performance of this product,
including the entire cost of any necessary servicing or repairs of any
defects.
10 On/off switch
6
11 Cord hook
12 Plastic loop / cable clamp
13 Connector assembly
14 Fan housing
10
14
7
8
15
Oreck’s liability for damages to you for any costs whatsoever arising out
of this statement of limited warranty shall be limited to the amount paid
for this product at the time of original purchase, and Oreck shall not be
liable for any direct, indirect, consequential or incidental damages
arising out of the use or inability to use this product.
15 Cord assembly
16 Handle brace
3
Assembly
Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not
apply to you.
fig. 1 Before assembling appliance, remove two screws from connector
assembly. Remove cardboard insert by pulling upward.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT,
INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN
DURATION TO THE WARRANTY PERIOD, AND NO WARRANTIES,
WHETHER EXPRESS OR IMPLIED, WILL APPLY AFTER THIS
PERIOD.
fig. 2 With ON/OFF switch facing the front of the unit, slide upper
handle section over matching section of the connector assembly.
Place brace against handle and connector assembly aligning
screw holes. Insert short screw into top hole and long screw into
the bottom hole then tighten firmly until handle is no longer loose.
Some states do not allow limitations on the duration of implied
warranties, so the above limitation may not apply to you.
Operating Instructions
This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
Make sure disposable paper filter dust bag is in place. DO NOT operate
the cleaner without a paper filter dust bag. Plug the power cord into an
electrical outlet and press the On (l) - OFF(O) switch on top of base
when ready to operate.
Unit Specifications
Up-Position Lock
Power head: Width 12 1/2”, Height 4”, Leading Edge 2 1/2”.
Self-adjusting to carpets and bare floors. Includes patented edge cleaning
device.
Motor: High performance precision motor, sealed ball bearing on solid
shaft. High temperature insulation, factory lubricated for life. Heat
dispersion system and motor cooling fan device, with self-cleaning blades.
fig. 3 Place foot on power head and lean handle back gently to release
lock for vacuum use. Return handle to the full upright position to
engage lock.
NOTE: Do not operate the unit while in the upright and locked position.
Do not let the unit run while in any one stationary position for any period
of time. Keep the unit moving while in operation.
Electrical: 120 volts A.C., 4 amps, 480 watts, 60 Hz.
Power cable: 35 feet long, Three conductor SJT type. Flexible heavy duty
jacket.
Operating Recommendations
This new ORECK XL High Speed Upright is one of the finest, fastest,
and strongest units in its class. You’ll love the way it cleans, gets under
things, and it’s SO lightweight and easy to use.
Sealing gaskets: Cover plate sealing gaskets absorb shock, insulate,
resist corrosive chemicals and abrasive contact. Provide effective seal
against dust and suction loss.
Agitation: Full intersecting dual-row sharp helix pattern nylon bristle brush
rotates on lifetime lubricated ball bearings. High speed alternating action
brush cleans at approximately 6,500 rpm. Bearing holders may be rotated
1/2 turn to extend bristle life. Dirt seals protect brush bearings from dirt
build-up.
The following are a few simple suggestions regarding its operation:
1. When inserting a new disposable paper filter dust bag—FIRST
PUFF OUT and OPEN THE BAG.
2. When the disposable filter dust bag is full, REPLACE IT.
3. If at any time the machine does not pick up properly or makes an
unusual noise, STOP OPERATION and service.
Drive belt: Most trouble-free because it’s sealed off from the dirt collection
area. Eliminates “center” dirt path. Motor drive shaft is
hi-carbon, stress proof steel, ground finish for minimum belt wear. Spare
belt is stored in baseplate.
4. Although your upright will pick up pins, paper clips, and other small
objects, it is recommended that these be removed from the floor
before you vacuum. Failure to do so may result in permanent
damage to the motor suction fan and its housing.
Super filter bag: 736 cubic inch capacity. Hypo-allergenic version is
CELOC® Hypo-Allergenic multi-layered, high dust retention, disposable
filter bag.
3
5. WARNING: Do not use your vacuum cleaner on damp or wet
surfaces. This will cause damage to the vacuum cleaner and is
dangerous to the user.
CAUTION—Wood Floors, Soft (Vinyl, Asphalt Tile, etc.) Floor
Surfaces and Polished Floor Finishes
Use floor and floor finish manufacturer’s recommended methods of
cleaning. The metal strip on the base of the cleaner could be damaged
if used on concrete or abrasive surfaces, and, therefore, cause damage
to wood floors, soft (vinyl, asphalt tile, etc.) floor surfaces and polished
floor finishes. The roller brush may also scuff very soft finishes. Do not
operate the unit while in the upright and locked position. Do not let the
unit run while in any one stationary position for any period of time. Keep
the unit moving while in operation.
6. REPLACE THE BELT EVERY 6 MONTHS.
7. Change the disposable filter dust bag at least once a month—
even if it is not full! The collected dust in the dust bag can cause
odor, attract moisture, and can affect the efficiency of the cleaner.
8. DO NOT run the vacuum cleaner over the cord. The revolving
brush could damage the cord.
9. Use caution when vacuuming over area rug edges and fringe.
General Information
To Replace Filter Dust Bag
WARNING: Unplug cord from electrical
outlet before servicing.
The performance of your new cleaner greatly depends upon care and
maintenance. The instructions in this manual will guide you in
performing basic care and maintenance. To obtain the most satisfying
years of service read the instructions and keep them handy for future
reference.
BAG REMOVAL:
fig. 4 Unzip outer bag completely.
fig. 5 Pull bag cardboard collar to release bag from connector.
BAG INSTALLATION:
Disposable Paper Filter Dust Bags
Disposable paper filter dust bags play a very important role in the
efficiency of your ORECK vacuum cleaner. The purpose of the filter bag
is to trap dirt, but at the same time it must be porous enough to allow air
to pass through. If the filter bag becomes clogged, no air can pass
through the cleaner and cleaning cannot take place, regardless of the
cleaner’s power.
fig. 6 Hook bottom of bag collar opening under lip "B" of connector
assembly. Pull up on bag collar and snap over lip "A" of
connector.
fig. 7 Press on edges of bag collar to insure bag is completely
installed.
To keep your cleaner operating at maximum efficiency, change the dust
bag frequently. DO NOT FILL ABOVE THE LINE INDICATED ON THE
DUST BAG.
IMPORTANT: Check to make sure bag collar is behind lips "A" and "B".
If it is not, dust will leak into outer bag. When filter bag is in place,
close outer bag with zipper fastener.
Be sure the disposable paper filter dust bag is installed properly.
All paper dust bags are not the same. Your ORECK disposable
dust bags have been designed to be used with the ORECK cleaner.
Using bags other than genuine ORECK disposable bags will affect
the cleaning ability of your cleaner and could cause damage to it.
How to Replace a Worn Belt
WARNING: Unplug cord from electrical
outlet before servicing.
The Belt
fig. 8 Remove the replacement belt from the storage channel.
The belt on your vacuum cleaner controls the speed of the revolving
brush and is very important for the effective operation of the cleaner. If
the belt becomes stretched or cut, it will cause the revolving brush to
stop completely or slow down. See instructions in the manual for
replacing belt.
fig. 9 Remove the door by removing the hold down screw located on
side of power head.
fig. 10 Slide the door forward by prying open with a screwdriver or
coin.
An extra belt is stored in the baseplate of your cleaner. When
buying replacement belts, use ONLY ORECK genuine belts. Belts
other than Oreck belts will not operate the revolving brush
correctly and may create undue stress which will cause damage to
the motor and brush bearings.
fig. 11 Remove the belt from the motor drive shaft and brush roll
pulley.
fig. 12 Loop the new belt over the motor drive shaft. Place the
opposite end of the belt on the brush roll pulley. Rotate the
brush roll three (3) complete revolutions to ensure that no part
of the belt is overhanging the end of the motor drive shaft.
Lubrication
The vacuum cleaner motor bearings are factory lubricated and sealed.
Further lubrication is not required.
fig. 10 Replace the door by sliding it into the groove at the bottom of
the housing.
General Cleaner Care
fig. 9 Replace the hold down screw and tighten.
At least once a month, check for
and remove excessive lint, string or
hair from revolving brush.
To Adjust or Replace Brush
WARNING: Unplug cord from electrical
outlet before servicing.
Wipe the outside of the cleaner with
a damp cloth. Also, clean the
connector deflector assembly area,
base of cleaner and fan housing
area. If there is dust in the outer
bag, vacuum it or shake it out.
fig. 13 To determine if the brush is worn, place a firm straight edge
across the nozzle opening. If brush bristles do not extend
beyond baseplate, brush should be adjusted.
fig. 14 Remove the baseplate by removing 5 screws.
A little preventative maintenance will
keep your cleaner looking new and
will ensure continued cleaning effec-
tiveness.
fig. 15 Remove the belt and brush roll from the housing.
fig. 16 Rotate both bearing assemblies at ends of brush roll to show
"OLD" and replace in the holding channels in the housing.
NOTE: The bearing assembly setting marked “OLD” has a smooth side
on the end card. The one marked “NEW” is notched on the end card.
When rotating bearings, make sure both bearing assembly settings are
the same and face up when replacing the brush roll.
fig. 13 Reassemble the belt and the baseplate and check bristle height
above baseplate at each end of brush.
If a previous adjustment has already been made and bristle height does
not extend above baseplate, a new brush assembly should be ordered.
4
IMPORTANT: Unless the brush is worn as indicated above, both
bearings must be in the “NEW” position. When rotating, both
bearings must be in the “OLD” position. Unmatched settings will
cause damage to your machine.
Troubleshooting Guide
WARNING: Unplug cord from electrical
outlet before servicing.
®
Using An Oreck Fresh Air Tab
SAVE SERVICE CALLS...CHECK THESE FIRST:
• Is the disposable filter dust bag full?
• Are pores of filter dust bag clogged with powder or fine dust?
fig. 17 Your ORECK XL vacuum cleaner has a special Oreck Fresh
Air® tab pocket. This pocket is located inside the outer bag in
the area where the disposable paper bag attaches to the intake
tube. Insert tablet in pocket if desired.
• Is anything clogging the revolving brush, lower tube, intake opening,
fan housing or connector assembly opening?
• Is the belt in place and turning the brush?
• Are the brush ends in the proper location?
Stuffing or Blockage
IMPORTANT: On plush and new carpets, stuffing may occur inside the
the intake tube and the lower tube assembly. This is due to excessive fuzz
and loose cuttings in the carpet. Stuffing could occur for the first few
cleanings until all the loose material is removed. Due to the high efficiency
of the cleaner, many older carpets will cause stuffing when the cleaner is
first used on them. If your vacuum cleaner does not pick up properly, or
makes unusual noise and the outer bag does not fluff up or balloon open,
follow these steps:
• Does the brush turn freely? Are hair, string or rug fibers wound around
the brush?
PROBLEM
CLEANER
POSSIBLE SOURCE
AREAS TO CHECK
Not plugged in
properly.
Be sure cleaner is
firmly plugged into
wall outlet.
WILL NOT RUN
WARNING: Unplug cord from electrical
outlet before servicing.
No electricity in wall
outlet.
Check electrical
source–fuse or
circuit breaker.
fig. 18 Check for blockage at the mouth of the intake opening. If there
is blockage, remove it with long-nose pliers, a screwdriver or
coat hanger. If you can not reach the blockage, remove (fig. 19).
CLEANER
DOES NOT PICK UP
Filter bag is full.
Replace filter bag. See
“To Replace Paper
Filter Dust Bag.”
fig. 20 If the blockage is not at the base, remove lower tube. Unhook
retainer spring, releasing bottom of bag.
fig. 21 Twist lower collar counterclockwise to slide up. Pull tube out of
Nozzle or intake
pivot clogged.
Clear obstruction.
Replace belt.
base.
fig. 22 Check for blockage. If blockage is in the tube, remove with a
coat hanger.
Belt is broken or
stretched.
fig. 23 If tube is not blocked, look into fan housing. Remove debris
with long-nose pliers, a screwdriver or coat hanger.
fig. 21 To reassemble, check O-ring on tube, and replace if damaged.
Vacuum will not operate properly without the tube O-ring. Slide
O-ring to approximately 2" from base of tube. Replace tube by
first lining up slot at base of tube with inner tab inside fan
housing. Then reinsert tube and push down until the tube is
seated. Make sure O-ring is in place against fan housing
opening. Replace and tighten collar until collar locking tabs are
locked in place.
Brush is worn.
See “To Adjust or
Replace Brush”
Bag tube clogged.
Clear obstruction.
Change bag.
Bag pores are
clogged with fine
dust.
fig. 24 Make sure collar is not cross threaded on housing. Reattach
bag spring (fig. 20).
Impeller fan is
broken.
Return to Service
Center for repair.
fig. 25 Many times blockage occurs due to a full dust bag causing dirt
to back down the air flow system. When that happens, the
blockage will be at the top of the system, starting in the area
where the dust bag connects to the connector assembly.
Revolving brush is
not even at both
ends.
Check brush roll end
cards. Make sure
words “old” or “new”
match at each end.
NOTE: If the above actions do not correct the problem, contact an
Oreck authorized service center or call the commercial customer service
center. USA: 1-800-989-1150
ALL OTHER SERVICING SHOULD BE DONE BY AN
ORECK AUTHORIZED SERVICE CENTER.
CALL COMMERCIAL CUSTOMER SERVICE
1-800-989-1150
Whenever calling, please be sure to have your model and serial
number from data plate.
5
6
75376-07 REV B
05/05 ECN# R-8018
©2005 Oreck Holdings, LLC. All Rights Reserved. All word marks, logos, registered trademarks and product configurations are
owned and used under the authority of Oreck Holdings, LLC.
|