•
Placement of this product on certain types
of wood may result in damage to its finish for
which Oregon Scientific will not be responsible.
Consult the furniture manufacturer’s care
instructions for information.
The contents of this manual may not be
reproduced without the permission of the
manufacturer.
Do not dispose old batteries as unsorted
municipal waste. Collection of such waste
separately for special treatment is necessary.
Please note that some units are equipped with
a battery safety strip. Remove the strip from the
battery compartment before first use.
·
·
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
LOCATION
Indoor temperature
area
Outdoor temperature
area
MEANING
Main unit batteries low
·
·
Sensor batteries low
•
•
•
Wireless Indoor and
Outdoor Thermometer
with LED Ice Alert
Consult the dealer or an experienced radio / TV
technician for help.
REMOTE SENSOR
To set up the sensor:
1. Open the battery compartment (see FIG 3).
2. Select channel 1 then press RESET.
3. Close the battery door.
Model: EMR201
DECLARATION OF CONFORMITY
USER MANUAL
The following information is not to be used as
contact for support or sales. Please call our
customer service number (listed on our website at
for this product) for all inquiries instead.
4. Place the sensor within 30 m (98 ft) of the main
unit using the table stand or wall mount.
OVERVIEW
NOTE The technical specifications for this product
and the contents of the user manual are subject to
change without notice.
FRONT VIEW
TIP Ideal placements for the sensor would be in any
location on the exterior of the home at a height of
not more than 5 ft and which can shield it from direct
sunlight or wet conditions for an accurate reading.
We
Name:
Address:
Oregon Scientific, Inc.
19861 SW 95th Ave.,Tualatin,
Oregon 97062 USA
T
E
M
P
SPECIFICATIONS
OUT
1
Telephone No.:
1-800-853-8883
2
TYPE
DESCRIPTION
declare that the product
MAIN UNIT
L x W x H
Product No.:
EMR201
T
E M P
66 x 27.5 x 87.5 mm
(2.59 x 1.08 x 3.44 in)
Product Name:
Wireless Indoor and Outdoor
Thermometer with LED Ice
Alert
IN
3
4
Weight
241 g (8.5 oz) without battery
Manufacturer:
Address:
IDT Technology Limited
Block C, 9/F, Kaiser Estate,
Phase 1,41 Man Yue St.,
Hung Hom, Kowloon,
Hong Kong
Temperature range -5°C to 50°C (23°F to 122°F)
���������
Resolution
0.1°C (0.2°F)
433 MHz
Signal frequency
Humidity range
25% - 95%
1. Remote sensor reception indicator
2. Outdoor temperature
3. Indoor temperature
is in conformity with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference
received, including interference that may cause
undesired operation.
Humidity resolution 1%
Power 2 x UM-4 (AAA)
1.5 V batteries
REMOTE UNIT (THN132N)
4. Ice alert LED indicator
NOTE Use alkaline batteries for longer usage and
consumer grade lithium batteries in temperatures
below freezing.
BACK VIEW
L x W x H
96 x 50 x 22 mm
(3.78 x 1.97 x 0.87 in)
SENSOR DATA TRANSMISSION
Weight
62 g (2.22 ounces)
To search for a sensor:
Reset the unit.
Transmission range 30 m (98 ft) unobstructed
Temperature range -20°C to 60°C (-4°F to 140°F)
The sensor reception icon in the remote sensor area
shows the status:
Power
1 x UM-3 (AA) 1.5 V batteries
ICON
OUT
DESCRIPTION
Main unit is searching
for sensor(s).
OUT
1
2
ABOUT OREGON SCIENTIFIC
C/
F
ET
RES
A channel has been
found.
The sensor cannot be
found.
OUT
OUT
OUT
OUT
learn more about Oregon Scientific products. If
you’re in the US and would like to contact our
Customer Care department directly, please visit:
www2.oregonscientific.com/service/support
OR
OUT
TIP The transmission range may vary depending
on many factors. You may need to experiment with
various locations to get the best results.
Call 1-800-853-8883.
For international inquiries, please visit:
www2.oregonscientific.com/about/international
1. °C / °F: Select temperature unit
2. RESET: Reset unit to default settings
ICE WARNING
If the channel 1 sensor falls between 3°C to -2 °C
(37°F to 28°F), LED indicator will flash, and will stop
flashing once the temperature is out of this range.
FCC STATEMENT
REMOTE SENSOR
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) This device must accept any interference
received, including interference that may cause
undesired operation.
2
RESET
Press RESET to return to the default settings.
1
WARNING Changes or modifications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
4
5
PRECAUTIONS
3
•
•
•
Do not subject the unit to excessive force,
shock, dust, temperature or humidity.
Do not cover the ventilation holes with any items
such as newspapers, curtains etc.
Do not immerse the unit in water. If you spill
liquid over it, dry it immediately with a soft,
lint-free cloth.
NOTE This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection
1. LED status indicator
2. Wall mount hole
3. Battery compartment
4. RESET hole
against harmful interference in
installation.
a
residential
•
•
•
•
•
Do not clean the unit with abrasive or corrosive
materials.
Do not tamper with the unit’s internal
components. This invalidates the warranty.
Only use fresh batteries. Do not mix new and
old batteries.
Images shown in this manual may differ from
the actual display.
When disposing of this product, ensure it is
collected separately for special treatment.
5. CHANNEL switch
This equipment generates, uses and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipmentdoescauseharmfulinterferencetoradioor
television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
GETTING STARTED
INSERT BATTERIES
1. Remove the battery compartment.
2. Insert the batteries, matching the polarities (see
FIG 2).
3. Press RESET after each battery change.
© 2007 Oregon Scientific. All rights reserved.
P/N: 086L005000-011
|