TP29 Caller ID Speakerphone
Keep this user guide for future reference
Always retain your proof of purchase in case of warranty service
-Operation-
1 General Information
Warnings
•
The telephone is designed for indoor use only. Do not install the telephone in areas where
there is the risk of an explosion, excessive exposure to smoke, dust, vibrations, chemicals,
moisture and heat.
•
•
•
Do not install in damp locations such as a bathroom or laundry, do not expose the unit to
direct sunlight.
Do not use your telephone during an electrical thunderstorm as it is possible to get an
electric shock. Refer to information contained in Telstra White pages directory.
The earpiece of the handset may attract small metal objects such as staples and pins.
Care should be taken when placing the handset near these items.
Quick connection information
Before installing or changing the battery, make sure that the telephone is not
connected to the telephone network.
First install the battery supplied, connect the curly cord to the phone and the
handset. Connect the line cord to the bottom of the phone and then to the wall
socket using the plug supplied. Lift the handset and check for dial tone.
LOCATION
Do not position the unit in the immediate vicinity of other electronic equipment
such as microwave or hi-fi units as this can lead to mutual interference. The
location has a deciding influence on the trouble-free operation of the telephone.
Stand the telephone on a flat, non-slip surface. The telephone feet do not
normally leave any marks on the surface. However, on account of the multitude
of varnishes and surface finishes used, surface marks caused by the feet of the
unit cannot be ruled out. Do not use the unit in areas where there is the risk of an
explosion. Excessive exposure to smoke, dust, vibrations, chemicals, moisture,
heat or the direct rays of the sun must be avoided.
DISPOSAL
If the useful life of the complete equipment has expired, please dispose of these
carefully in accordance with the statutory requirements and in a manner friendly
to the environment.
Temperature and ambient conditions
The telephone is designed for indoor use (temperature range of -10 °C to 50 °C).
Do not install the telephone in areas where there is the risk of an explosion,
excessive exposure to smoke, dust, vibrations, chemicals, moisture, and heat. The
unit must not be installed in damp locations such as a bathroom or laundry, do
not expose the unit to direct sunlight.
-Operation-
Cleaning and care
The surface of the case can be cleaned with a dry, soft, lint-free cloth. Never use
cleaning agents, particularly aggressive solvents. Apart from occasional cleaning
of the case, no other care is necessary. The rubber feet of the base station are not
resistant to all cleaning agents. The telephone feet do not normally leave any
marks on the surface. However, on account of the multitude of varnishes and
surface finishes used, surface marks caused by the feet of the unit cannot be
ruled out. The manufacturer can therefore not be held responsible for possible
damage to furniture or the like.
NOTES FOR OPERATION IN NEW ZEALAND
Only that Telecom has accepted that the item complies with the minimum
conditions for connection to its network. It indicates no endorsement of the
product by Telecom, nor does it provide any sort of warranty. Above all, it
provides no assurance that any item will work correctly in all respects with
another item of Telepermitted equipment of a different make or model, nor does it
imply that any product is compatible with all of Telecom’s network services. This
device may be subject to ringing or bell tinkle when certain other devices are
connected to the same line. If this occurs, the problem should not be referred to
the Telecom Faults service.
This equipment shall not be set to make automatic calls to the Telecom “111”
Emergency Service. This equipment may not provide for the effective hand-over
of a call to another device connected to the same line.
REN (RN for New Zealand)
The REN (Ringer Equivalence Number) or (RN) is of significance only if you wish to
connect more than 1 telephone to your telephone line. A standard telephone line
has a maximum REN capacity of 3 (RN of 5). It is possible to connect 3(5) devices
with a REN of 1 (RN of 1) with no degradation to the product’s performance.
Exceeding this limit may cause the volume of the ringer in any phone to decrease
or not ring at all.
Caller ID
Customers using non Telecom toll services should not use the dial back feature for
local calls as this will incur a charge only the 7 digit number should be dialled.
Some of the CID services listed may not be available in New Zealand.
-Operation-
2 Operating Functions
1
2
3
4
5
6
7
8
9
One touch buttons A1, A2 to A10
Memory button
Dial/Menu button
Book button
Clear button
d button
c button
Message indicator
Redial/Pause button
10 Store button
11 Recall button
12 Mute button with indicator
13 Handsfree button with indicator
14 Volume adjustment
15 Hanger for handset
16 Connection for Headset cable
17 Speaker/Headset selection switch
Lower surface of the telephone
Ringer adjustment switch
PBX message waiting selection switch
Slots for desk support
Connection for handset curly cord
Connection for telephone cable connection
Battery compartment
-Operation-
3 Installation
3.1 Safety information
NOTE! Before installation, it is essential that you read the general information at
the beginning of this user guide.
3.2 Check contents of pack
The following items are supplied in this pack:
One telephone base
One handset
One telephone line cord
One modular adaptor plug (Aus only)
One desk support
One curly cord
This user guide
Three AAA batteries
One warranty card
3.3 Installing the batteries
Install the 3 AAA batteries (supplied) before connecting your telephone to the
telephone network. The battery is required for the display, handsfree and other
functions of the telephone.
1. Make sure that the telephone is not connected to the telephone network.
2. Locate the battery compartment on the underside of your telephone.
3. Open the battery compartment with a pen tip or a pointed object.
4. Insert the battery, ensuring that the polarity is correct.
5. Close the battery compartment.
The LCD display may not display until you are connected to a telephone line and
pick up the receiver. This is for protecting the telephone memory while replacing
battery. See section 3.5 for procedure of connecting the phone line.
The battery should be changed when the
icon is displayed on the LCD. If
the battery becomes completely discharged, you could lose the stored numbers.
Do not use rechargeable batteries, as these could possibly lead to a short circuit.
When replacing the batteries use only AAA 1.5V alkaline batteries.
WARNING
Do not throw batteries into fire or immerse in water. Do not dispose of
old or faulty batteries with the normal household waste.
-Operation-
3.4
Connecting the telephone handset
After unpacking your telephone, you must first connect the telephone handset to
the base unit. First take the short end of the curly cord and plug it into the socket
on the handset. Turn the telephone base over and plug the long end into the
socket marked with a handset
cable through the cable channel.
symbol located on the right hand side. Feed the
3.5 Connecting to the phone line
Connect the telephone cable supplied to the telephone wall socket and to the
socket marked with a
symbol on the base of the phone. Then feed the cable
out of the telephone housing either upwards or downwards through the cable
guide. Clip the cable firmly in the cable channel.
3.6
Connecting a headset (not supplied)
Make sure that your headset is fitted with a RJ type connector before connecting
to the unit. The RJ type connector is the same as the telephone handset curly
cord. To install a headset, please turn the right side of the telephone base up and
plug the headset cord into the headset jack marked with a ” symbol. After the
headset jack is connected, move the Speaker/Headset selection switch, which is
adjacent to the headset jack, to Headset position. Return the unit to the upright
position, replace the handset and press the Handsfree button
to see whether
the headset is working. If headset does not work properly, try the next headset
position of the Speaker/Headset selection switch. Please note that once you
select headset operation the Handsfree button
only. The speakerphone operation is disabled.
will work for the headset
To disconnect the headset, check the Speaker/Headset selection switch to the
speaker position. The Handsfree button
The headset operation is then disabled.
will work for the speakerphone only.
3.7 Recall button
You can use the Recall button on your telephone when using your network
operator’s services such as call waiting etc. A subscription may apply for these
services, contact your network operator for more information. If this is not
working correctly check the country option of the phone menu and select Australia
or New Zealand option. For Australia it should be set to 100ms and for New
Zealand is 600ms.
-Operation-
3.8
Fitting the desk support
If you intend to use your telephone on a desk, then the desk support supplied
must be fitted. To do this, turn the telephone over. Now insert the two upper
hooks into the openings provided and push the desk support firmly home.
If you ever need to remove the support, press gently on the middle clips on the
upper edge and then pull the desk support off.
In the handset rest there is a small hanging device, which is used when the
telephone is wall mounted. This hanging device is not required when the
telephone is used on a desk, as it impedes lifting of the handset. Using a small
screwdriver, turn this hanging device until the screw is completely flush and its
upper end does not protrude at all.
3.9 Wall mounting
Your telephone is also suitable for wall mounting. Use two screws for fixing. Drill
two holes horizontally side by side, 70mm apart, and leave the screws
protruding from the wall by 5mm. Now place the telephone over the screws and
push it slightly downwards.
There is a small hanging device in the handset rest to prevent the handset from
falling when it is placed on the rest with the telephone mounted on the wall.
Using a small screwdriver, turn this hanging device until a small hook appears
at the upper end.
If you are using the telephone fitted to the wall, you can hang the handset on
the telephone without hanging up. You will find a small hook for this purpose at
the upper end of the handset rest.
3.10 Adjusting display contrast
To adjust the display to suit the local lighting conditions, please proceed as
follows:
1. Press the DIAL/MENU button for 3 seconds. The display shows
“OPTIONS cd”.
2. Press the c buttons until the display shows “LCD CONTRAST”.
3. Press the DIAL/MENU button to enter setup mode.
4. Now select the desired contrast between 0 to 7 using the d and c
buttons.
5. Confirm with DIAL/MENU button.
6. Press RECALL button to exit menu.
-Operation-
3.11 Setting the time/date
If you want to reset the time or change a time already entered, proceed as
follows:
1. Press the DIAL/MENU button for 3 seconds. The display shows
“OPTIONS cd”.
2. Press the c buttons until the display shows “TIME/DATE”.
3. Press the DIAL/MENU button. The hour display will flash.
4. Press the d and c button until the correct number of hour appears in the
display.
5. Press the DIAL/ MENU button. The minutes display will flash.
6. Press the d and c button until the correct number of minute appears in
the display.
7. Press the DIAL/ MENU button. The month display will flash.
8. Press the d and c button until the correct number of month appears in
the display.
9.
10. Press the DIAL/ MENU button. The date display will flash.
11. Press the d and c button until the correct number of date appears in the
display.
12. Press the DIAL/ MENU button. The setting is completed
13. Press the RECALL button to exit.
Note: If you have subscribed to your service providers Caller ID service. The
time and date is updated using the caller ID information from your service
provider.
3.12 Call Duration Display
The call duration is shown in the display in minutes and seconds during a call.
The indication starts after the number has been dialled. The call duration is
displayed for a few seconds after the call has ended.
3.13 Adjustable Ringer Volume
You can use the
(loud) or (soft) to adapt the ringer volume to your requirements. Should
you not want to be disturbed, select (off).
slide switch underneath the telephone to select the settings
-Operation-
3.14 Last Number Redial
If a connection that you have dialled is engaged or you were unable to get
through, simply replace the receiver. The last number dialled will be saved in
the telephone automatically. To use the redial facility, proceed as follows:
1. Lift the receiver or press the handsfree button
.
2. Press the REDIAL/PAUSE button the saved redial number will now be
dialled
3.15 Auto Redial
If a connection that you have dialled is engaged or you were unable to get
through to anybody, simple press the DIAL/MENU button when you are on
the handsfree or headset mode. The last number dialled will be saved in the
telephone automatically. To use the auto redial facility, proceed as follows:
1. Press the handsfree button
.
2. Dial the required telephone number or press the DIAL/MENU button to
dial the saved last number.
3. If the number cannot get through, press the DIAL/MENU button. The
phone will automatically try the number continuously until the call is get
through or the number is tried ten times.
4. When the call is getting through, the phone will play several beep sound.
After the beep sound, you can talk on the phone.
4
Operation
4.1 Making a call using the receiver, handsfree and
headset feature
A: Making a call using the receiver
1.
2.
Lift the receiver and wait until you hear a dialling tone.
Now dial the required telephone number. The display shows the number
dialled. If the number dialled is longer than 32 digits, only the last 32 digits
will be saved in the redial memory.
3.
4.
If the receiver volume is too quiet or too loud, you can change this to suit
your requirements. Adjusted the volume with the + and - buttons.
To end the call, replace the receiver.
-Operation-
B: Making a call using the handsfree facility
1.
Press the handsfree button
. The LED above the button will come on
and you will hear the dial tone from the speaker.
2.
Now dial the required telephone number. The display shows the number
dialled. If the number dialled is longer than 32 digits, only the last 32
digits will be saved in the redial memory.
3.
When the other party accepts the call, his voice will be heard over the
speaker. When using the handsfree facility always speak loudly and clearly
towards the telephone.
4.
5.
Adjust the speaker volume with the + and - buttons.
To end the call, press the handsfree button
.
Tip! If you want to change during a call from the receiver to the handsfree press
the button and replace the receiver.
C: Making a call using the headset facility
The headset works only when a (optional) headset is installed. To see how to
install for a headset please see section 3.6.
1.
Press the handsfree button
. The LED above the button will come on
and you will hear the dial tone from the headset.
2.
Now dial the required telephone number. The display shows the number
dialled. If the number dialled is longer than 32 digits, only the last 32
digits will be saved in the redial memory.
3.
When the other party accepts the call, his voice will be heard over the
headset. When using the headset facility always speak clearly towards the
microphone of the headset.
4.
5.
Adjust the headset volume with the + and - buttons.
To end the call, press the handsfree button
.
Tip! If you want to change during a call from the receiver to the headset press
the button and replace the receiver.
D: Dialling a phone number while the phone is on-hook
1.
2.
Press the required telephone number when the phone is on-hook. The
display shows the number dialled. If the number dialled is longer than this,
only the last 32 digits will be displayed.
To dial the entered number, simply pick up the receiver or press the
handsfree button
.
Tip! If you enter the wrong number, you can use the CLEAR button to edit the
number.
-Operation-
E: Receiving Calls
Calls can be accepted either by using the receiver or by using the handsfree
facility. Lift the receiver or use the handsfree facility by pressing the handsfree
button.
To end the call, replace the receiver or press the handsfree button
.
F: Muting the microphone
When on a call you can talk to someone in the same room without the caller
hearing you.
1. To mute the microphone, press the MUTE button once while a call is being
made. The indicator light in the button will be turn on.
2. To switch the microphone on again, press the MUTE button once more.
The indicator light will go out and you will be able to continue your call as
normal.
5
Storing telephone numbers
You can store 119 numbers in your telephone. Ten numbers can be stored under
the one touch memory buttons A1, A2 to A10. Ten additional numbers under
the speed dial buttons. The numbers 0 to 9 on the keypad are used as speed dial
buttons. The last 99 numbers can be stored under the phonebook memory which
is accessed by the BOOK button. The phonebook memory is organized in
alphabetical order. The name in the phonebook will be display when the caller’s
number matches the telephone number in the phonebook.
5.1 Saving a number under a one touch dial button
1. Press the Store button. The display shows “ENTER NUMBER”.
2. Enter the required telephone number with a maximum of 22 digits
using the number pad.
Note: If you enter the wrong number, you can use the CLEAR button to
edit the number.
3. Now press one of the ten one touch dial button A1, A2 to A10.
5.2 Saving numbers under the speed dial buttons
1. Press the Store button. The display shows “ENTER NUMBER”.
2. Enter the required telephone number with a maximum of 22 digits using the
number pad.
-Operation-
Note: If you enter the wrong number, you can use the CLEAR button to edit
the number.
3. Now select a speed dial storage location by pressing MEMORY button and a
number between 0 and 9 on the number pad.
Tip!
To erase a stored number simply store a new number in the storage location that
you want to erase. The storage locations can be written on the index card for
quick reference. Remove the protective transparent cover using a ballpoint pen or
a small pin.
5.3 Saving numbers in the phonebook
1. Press the BOOK button. The display shows “SEARCH ADD” with “SEARCH”
flashing.
2. Press the c buttons until the “ADD” is flashing.
3. Press the BOOK button again to confirm.
4. Enter the name characters (maximum 15 chars) using the number buttons.
5. Press the BOOK button to advance to telephone number.
6. Enter the telephone number (maximum 15 digits) using the number buttons.
7. Press the BOOK button to store the number in phonebook.
8. If you want to enter the next telephone number, press the RECALL button
back to step 2.
Tip!
If you enter the wrong number, you can use the CLEAR, d and c buttons to
edit the number.
5.4 Making a call using the one touch dial buttons
1. Lift the receiver or press the handsfree button
.
2. Now press the required one touch dial button A1, A2 to A10. The stored
number will now be dialled automatically.
3. To end the call, replace the receiver or press the handsfree button
.
-Operation-
5.5 Making a call using the speed dial buttons
1. Lift the receiver or press the handsfree button
.
2. Press the MEMORY button
3. Now press the required storage location between 0 and 9 on the keypad. The
stored number will now be dialled automatically.
4. To end the call, replace the receiver or press the handsfree button
.
5.6 Making a call using the phonebook number
1. Press the BOOK button. The display shows “SEARCH ADD” with “SEARCH”
flashing.
2. Press the BOOK button to search a phone number.
3. Press the number buttons to search the name field in alphabet order. Press
the d and c buttons to continue the search.
4. After the telephone number is displayed. Lift the receiver or press the
handsfree button
.
5. To end the call, replace the receiver or press the handsfree button
.
Tip!
You can make calling via multiple telephone network providers considerably
easier. Save their access numbers and the telephone numbers separately in
different storage locations. First dial the memory location for the network provider
and then the memory location for the required telephone number or dial the
required telephone number manually.
6 Caller Number Display (CID)
If you subscribe to your telephone network operators Caller ID service, numbers
of the incoming calls will be displayed on the display and stored in the call log. All
calls are saved in a caller list with date and time so that you will not miss any
calls. Up to 60 numbers are saved in the caller list. When the list is full, the oldest
number is always deleted from the list.
If calls are registered during you will see in the display “TOTAL 43 NEW 05”
-Operation-
This indication in the display shows that there is a total of 34 calls in the caller list.
There are 5 new calls in the caller list that have not yet been checked. In addition,
when there are new calls, the NEW Call indicator flashes.
6.1 Viewing the Caller List
While the phone display “TOTAL XX NEW XX”, press the d or c button the caller
list appears in the display. The first display is the last call received.
12:34AM 12/24
58
The first line shows the time/data and the storage
24775520
location in the caller list. If the symbol
appears, then the call has not yet been checked in the
list.
JOHN SMITH
You can look through the caller list using the d or c button. When you reach the
last storage location in the list, the display shows the message “END OF LIST”.
If the caller list appears no name or no number, the caller has either suppressed
the transmission of his number or the number could not be transferred.
6.2 Phonebook name matching display
If the telephone number of the caller is appeared in the list of the phonebook, the
name in the phonebook will be displayed.
6.3 Call waiting display
Call waiting is an optional service from your telephone service provider. If this
service is not available, the call waiting will be display even you have caller ID
service. Please ask your telephone service provider for further information. Call
waiting is received during you are having a call. You can hear a special tone at
the receiver and come with the display shortly.
12:00AM 11/20
PETER
60
24883540
The icon
will display with the caller number. If
you decide to switch to the new caller, you can press
the RECALL button. If your want to switch back to the first caller, press the
RECALL button again.
-Operation-
6.4 Select Language
ENGLISH, FRANCAIS, ESPANOL, DEUTSCH, ITALIANO, PORTUGUES, TURKISH,
DANSK prompts for caller I.D. message display can be selected. Please proceed
as follows:
1. Press the DIAL/MENU button for 3 seconds. The display shows “OPTIONS
cd”.
2. Press the c buttons until the display shows “LANGUAGE”.
3. Press the DIAL/MENU button.
1. Use d and c button to select the preferred language.
2. Confirm with DIAL/ MENU button.
3. Press RECALL button to exit menu.
6.5 Setting the Local Area Code
1. Press the DIAL/MENU button for 3 seconds. The display shows “OPTIONS
cd”.
2. Press the c buttons until the display shows “LOCAL AREA CODE”.
3. Press the DIAL/MENU button. The display shows “-----“
4. Use d and c button to select the number.
5. Press the DIAL/MENU button to advance a digit. If you finish the digit,
press the DIAL/MENU button.
6. Press RECALL button to exit menu.
6.6 Select country option
The country option defines the phone settings so that the phone works for
different country networks.
1. Press the DIAL/MENU button for 3 seconds. The display shows “OPTIONS
cd”.
2. Press the c buttons until the display shows “COUNTRY”.
3. Press the DIAL/MENU button. The display shows “AUSTRALIA“
4. Use d and c button to select either AUSTRALIA or NEW ZEALAND.
5. Press the DIAL/MENU button to confirm the setting.
6. Press RECALL button to exit menu.
6.7 Deleting numbers from the caller list
1. Press d and c button to select the required call number on the display.
2. Press CLEAR button. Display shows “DELETE CALL?”
3. Press CLEAR button again to confirm.
-Operation-
6.8 Deleting the entire caller list
1. Press d or c button to display the caller list.
2. Press and hold CLEAR button for 5 seconds. Display shows “DEL ALL
CALLS?”
3. Press CLEAR button again to confirm.
6.9 Dialling a telephone number directly from the Caller
List
You can dial telephone numbers directly from the caller list.
1. Press d and c button to select the required call number on the display.
2. Now press DIAL/MENU button, the display show area code filtered number.
If you want to select the number format with area code and long distance
code, press the DIAL/MENU button again. After the selected number is
show on the display, the number will be dialled automatically after 2 seconds.
The handsfree LED indicator will illuminate.
Note!
If your selected country option be New Zealand, the phone will
automatically recognise whether the number is long distance. If the number is a
long distance number it will add the long distance code “0” in font of the
telephone number and will show on the display.
6.10 Saving a number from the Caller List to the
telephone memory
A telephone number stored in the caller list can be saved directly to the telephone
memory.
1. Press d and c button to select the required call number on the display.
2. Press STORE button. Display shows “ENTER LOCATION”
3. Enter memory location that the number to be stored. The location can be
A1, A2, A10 or MEMORY 0 to 9.
6.11 Message Waiting Indication
Message Waiting is an optional service from your telephone service provider. If
this service is not available, the MSG indicator will not operate. Please ask your
telephone service provider for further information. When the message waiting
signal is received the
on.
icon as well as the MESSAGE indicator light are turned
Usually, the message waiting status will be cleared when you retrieve your
messages. If this does not happen you can clear the MESSAGE indicator
manually. Simply press and hold CLEAR button for 2 seconds. The MESSAGE
indicator will turn off.
-Operation-
7 Using phone on a PBX (phone System)
7.1 Pause function when using phone on a PBX
Note! The pause function between the code for the outside line (usually 0 or 9)
and the dialling tone described in this chapter is only necessary on older private
exchanges.
With some private exchanges, there is a short pause between the code for the
outside line (usually 0 or 9) and the dialling tone. This pause can be entered when
dialling manually and when dialling from the phone book so that the following
numbers are not dialled too quickly.
Entering the pause when dialling manually
Press the REDIAL/PAUSE button once between the code for the outside line and
the actual telephone number. After an outside line has been obtained, you
telephone will wait for 2 seconds before dialling the actual telephone number.
Storing the pause with the number
Simply press the REDIAL/PAUSE button after the code for the outside line and
before the actual telephone number when storing the number. When dialling from
the phone book, a pause of three seconds will then be automatically inserted after
the code for the outside line.
7.2 Recall function when connected to a PBX
If you have connected your telephone to a PBX, you can use all the facilities such
as call transfer, automatic recall, etc. The RECALL button provides access to
these facilities.
7.3 PBX Message waiting indicator
When the MSG (message) indicator turned on solidly, the indicator is activated by
some PBX’s. The TP29 offers two types of PBX message wait indication.
Use the Message Setting Switch located at the lower side of the unit to select
the setting to suit your PBX the default setting is OFF. Choose either Line polarity
reversal select (LR) or high DC voltage, select (HV).
-Operation-
8 Important Information
8.1
Troubleshooting
If you feel this product is not working correctly please consult the user guide and
ensure that you are using the product in accordance with the instructions.
Remove all extra telephone equipment and connect only this telephone directly to
the telephone socket.
If the fault is still present, connect another telephone (if available) to the
telephone socket. The results will show you whether the fault lies with this unit or
with the telephone line. If the product is working correctly the fault is on the
telephone line. Please contact your network operator for assistance
In the case of technical problems with this product please consult our website for
further information or send us an email for a prompt response to your enquiry.
8.2
Warranty Information
This product is covered by a 12 month warranty against defective workmanship or
parts, effective from the date of purchase.
NOTE: The warranty does not extend to damage caused by misuse, negligence,
excessive voltage, faults on the telephone line or lightning. This guarantee in no
way affects your statutory rights. Full details of the warranty are contained in the
enclosed warranty card.
In the unlikely event of a fault during this period, please contact us for
assistance. If the product is then found to be faulty you will be asked to
return it directly to us with a copy of the purchase receipt.
Australia
New Zealand
Oricom International Pty Ltd
ABN 46 086 116 369
Locked Bag 658
Atlas Gentech (NZ) Limited
Private Bag 14927,
Panmure,
South Windsor, NSW 2756
Auckland
Customer support
Email: [email protected]
Web: www.oricom.com.au
Fax: (02) 4574 8898
Customer support
Email: [email protected]
Fax: (09) 574 2722
Ph: 1300 889 785
Ph: 0900 50 025 (Toll Call)
|