Please observe safety precautions fully.
Safety Precautions
1. Introduction
General
Caution
Thisis a compact AC geared-motor having multiple international standard certifications.To use this
product for a prolonged period, read this manual thoroughly.
Failure to heed this instruction will result in
electric shock or fire.
Don't put an object or finger into the motor
opening.
This is designed for use in corporation with general purpose industrial devices. The product must
be handled by experienced personnel familiar with the product.
Failure to heed this instruction will result in
fire, personal injury, malfunction or damage.
Don't turn off and on power so frequently.
Don't pull leadwires with an excessive force.
<note>
Failure to heed this instruction will cause
fire, electric shock or personal injury.
When export this product, follow statutory provisions of the destination country.
Don't use the equipment in highly intensive
electric field.
Failure to heed these instructions will
cause personal injury or fire.
Unpacking
Don't use the equipment under direct sunshine.
• Proceed as follows:
Induced malfunction will cause
malfunction or personal injury.
Don't use the equipment in an environment where
electro-static voltage potentials may be produced.
• First open the top of the packing and check the units for damage in transit.
• Check the motor nameplate for the model number, output, No. of poles, voltage, frequency,
etc.
Failure to heed this instruction will result in
personal injury or malfunction.
Don't drop or cause topple over of something
during transportation or installation.
Failure to heed this instruction will result in
fire, electric shock, personal injury or
malfunction.
Never attempt to perform modification,
dismantle or repair.
Do not use the product if it does not meet your specification (if you dare to use it, burn
injury or fire may result).
Perform installation by taking into
consideration the mass of the body and rated
output of the product.
• A single-phase motor comes with capacitor and capacitor cap. Check the rated capacitance
and voltage on the nameplate. Do not use the accessory capacitor if it does not meet your
specification (if you dare to use it, you may be injuried or may have fire).
• Gear head is optional.
Adjust the motor ambient environmental
condition to match the motor operating
temperature and humidity.
Failure to heed these requirements will
result in personal injury or malfunction.
• Check a gear ratio on the nameplate. Do not use it if it does not meet your specification (if you
dare to use it, you may be injuried or may have fire).
Exactly follow the installing method and
direction specified.
Connect a ground-fault interrupter, circuit breaker
and replay to the brake control relay in series so
that they are turned off upon emergency stop.
Missing of one of these devices will cause
malfunction.
Should you find any discrepancy in the product, consult your local dealer.
Test-run the securely fixed motor without
loading to verify normal operation, and then
connect it to the mechanical system.
Operation using a wrong model or wrong
wiring connection will result in personal injury.
Level of input voltage to peripheral devices
Operation from a voltage outside the rated voltage
should correspond to the motor rated voltage. will cause electric shock, personal injury or fire.
Provide protection device against idling of
No protection will cause personal injury,
damage, pollution or fire.
electro-magnetic brake or gear head, or
grease leakage from gear head.
Don't place any obstacle object around the
motor and peripheral, which blocks air passage.
Temperature rise will cause burn injury or
fire.
Correctly run and arrange wiring.
Wrong wiring will cause personal injury or
electric shock.
Maintenance must be performed by an
experienced personnel.
Always keep power disconnected when the
power is not necessary for a long time.
Improper operation will cause personal
injury.
Scraps must be treated as industrial waste.
– 4 –
– 5 –
1. Introduction
2. Installation
Names and functions
Motor
Installation location
Gear head nameplate
Motor Nameplate
Frame
Install the motor as described to prolong the motor lifetime in a place where;
(1) is free from rain and direct sunlight.
(2) is free from vibration 4.9 m/s2 or more; shock, dust, iron powder or oil mist; splash of water. oil
and grinding fluid; and away from flammable materials, corrosive gas (H2S, SO2, NO2, Cl2, etc.)
or flammable gas.
O ring
Oil seal
Key
Bracket
Oil seal
(3) is enough ventilated dry and clean keeping oil, water, dust and heat away.
(4) you can check and clean the motor easily.
(5) is not in a closed environment where the motor temperature may increase. This may result in
the motor life shortened.
Wiring
nameplate
Output shaft
Environmental condition
Item
Description
Earth ground terminal
–10°C to 40°C (no freezing) *1
85% RH or below (no dewing)
–10°C to 60°C (no freezing) *2
4.9 m/s2 or below (10 to 60 Hz)
Lower than 1000 m.
Shaft
Ambient temperature
Ambient humidity
Storage temperature
Vibration
M4 x 6 stainless steel
with spring and flat washer
Capacitor cap
Altitude
Flat washer
Nut
Screw
1) Measurement taken at a point 5 cm from the motor.
*
*
#187
2) Allowable range for a relatively short period, for example, during transportation.
Quick connect
tab (Faston)
Gear head accessories
Installation
Capacitor
The motor can be installed vertically or horizontally but leadwires should be directed downward.
Motor accessories
(only for single phase version)
Keep the motor away from oil, water and dust
(1) Don't run the cable in water or oil.
Motor
(2) Don't expose the motor to splashing oil or
water.
Don't remove the nameplate.
*
Cable
Oil, water
– 8 –
– 9 –
|