PLD193T
OWNER'S MANUAL
Mobile Video System
Anti Theft Flip Down Detachable Panel
AM/FM Digital Pll Tuning Radio
Car DVD/VCD/CD/MP3 Player/TV Tuner
Auxiliary Input Function
Parental Control
Remote Control
SAFETY INFORMATION
CAUTION:
THIS DVD PLAYER IS A CLASS I LASER PRODUCT. HOWEVER THIS DVD
PLAYER USES A VISIBLE/INVISIBLE LASER BEAM WHICH COULD CAUSE .
HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE
THE DVD PLAYER CORRECTLY AS INSTRUCTED.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.DO NOT OPEN COVERS AND DO NOT
REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
EQUIPMENT TO RAIN OR MOISTURE.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, AND ANNOYING
INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES.
THIS DEVICE IS INTENDED FOR CONTINUOUS OPERATION.
This product incorporates copyright protection technology that is protected
by method claims of certain U.S. Patents and other intellectual property rights
owned by Macrovision Corporation and other rights owners.Use of this
copyright protection technology must be authorized by Macro vision Corporation,
and is intended for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
REGION MANAGEMENT INFORMATION:
This DVD Player is designed and manufactured to respond to the Region
Management Information that is recorded on a DVD disc. If the Region number
described on the DVD disc does not correspond to the Region number of this
DVD Player, this DVD Player cannot play this disc.
2
DISC NOTES
unusable) depending on your handle it
and conditions in the usage environment.
Note these scratches are not an
Disc formats supported by this
player
DVD
12 cm disc
V I D E O
indication of any problem with the player.
Label side
up
(Single-sided disc only)
Video CD
12 cm disc
CD
Do not touch
the
underside
of the disc
12 cm disc
MP3
12 cm disc
MP3
CD-RW
Do not
bend
Discs which cannot be played
with this player
DVD-ROM
DVD-R/DVD-RAM
CDV
Wipe the disc from
center
toward the outside
edge
CD-G
Handling and Cleaning
Dirt, dust, scratches and warping disc
will cause misoperation.
Do not place stickers or make
scratches on discs.
Preparing New Discs with Rough
Spots
A new disc may have rough edges on
its inside and outside edges.If a disc
with rough edges is used, the proper
setting will not be performed and the
player will not play the disc.Therefore,
remove the rough edges in advance
by using a ball point pen or pencil as
shown on the right.To remove the
rough edges, press the side of the pen
or pencil against the inside and outside
edges of the disc.
Do not warp discs.
A disc should always be kept in its
case when not in use to prevent from
damaging.
Do not place discs in the following
places:
1.Direct sunlight
2.Dirty, dusty and damp areas
3.Near car heaters
4.On the seats or dashboard
Rough spots
on
outside edge
Disc Cleaning
Use a dry soft cloth to wipe the surface.
If the disc is quite dirty, use a soft cloth
slightly moistured with isopropyl (rubbing)
alcohol. Never use solvents such as
benzine, thinner or conventional record
cleaners as they may mar the surface of
the disc.
Ball point pen
or pencil
Rough spots
on inside
edge
Note:
A disc may become somewhat scratched
(although not enough to make it
3
INSTALLATION
NOTES:
Choose the mounting location where the unit will not interfere with the normal
driving function of the driver.
Before finally installing the unit, connect the wiring temporarily and make sure
it is all connected up properly and the unit and the system work properly.
Use only the parts included with the unit to ensure proper installation. The use
of unauthorized parts can cause malfunctions.
Consult with your nearest dealer if installation requires the drilling of holes or
other modifications of the vehicle.
Install the unit where it does not get in the driver's way and cannot injure the
passenger if there is a sudden stop, like an emergency stop.
If installation angle exceeds 30 from horizontal, the unit might not give its
optimum performance.
30
Avoid installing the unit where it would be subject to high temperature, such
as from direct sunlight, or from hot air, from the heater, or where it would be
subject to dust, dirt or excessive vibration.
DIN FRONT/REAR-MOUNT
This unit can be properly installed either from "Front"(conventional DIN
Front-mount) or "Rear"(DIN Rear-mount installation, utilizing threaded
screw holes at the sides of the unit chassis). For details, refer to the following
illustrated installation methods.
4
INSTALLATION
DASH BOARD
METAL MOUNTING
STRAP
HEX NUT
SPRING WASHER
PLAIN WASHER
TAPPING SCREW
CONSOLE
SLIDE BRACKET
HOUSING
HEX BOLT
KEY PLATE
PLASTIC TRIM OUT
KEY PLATE
1.WHILE INSTALLING THE FRONT PANEL, PLEASE MOUNT THE LEFT SIDE FIRST,
AND MAKE THE DIRECTION HOLE ON THE FRONT PANEL AIM AT THE LEFT GUIDE
ON THE UNIT
2.THAN PUSH THE RIGHT SIDE TO MOUNT THE RIGHT GUIDE
3.PUSH IT TO INSTALL THE
FRONT PANEL COMPLETELY .
5
INSTALLATION
CAUTION: DO NOT INSTALL THE DETACHABLE PANEL BEFORE
CONNECTING THE WIRE.
1. The unit is designed for negative terminal of the battery which is connected to the
vehicle metal. Please confirm it before installation.
2. If the car interior is extremely hot, as after being parked in the sun, do not use the
player until the car has been driven for a while to cool off the interior.
3. Press the OPEN button to flip down the front panel (see fig.1), Slide the guide knob
to remove the right side first, then take away the front panel. (see fig.2) and put it in the
protective case (see fig.3) for safe keeping.
4. Install the front panel back into its bracket and then push it back to the position for
playing (see fig.4).
FRONT PANEL
GUIDE KNOB
OPEN BUTTON
(FIG.1)
(FIG.2)
PROTECTIVE CASE
FRONT PANEL
FRONT PANEL
(FIG.3)
(FIG.4)
6
ELECTRIC CONNECTION
WIRING CONNECTION
MAIN UNIT
TV ANT IN
ANTENNA CONNECTOR
IGNITION RED
AUX(optional)
RCA CABLE
VIDEO IN YELLOW
RCH IN RED
LCH IN WHITE
GREY SUBWOOFER
VIDEO OUT 2 YELLOW
COAXIAL OUT BROWN
RCH RED
SWITCH(B+)
REAR RCA OUTPUT
CABLE (optional)
CHOKE
BOX
MEMORY
BACK-UP(B+)
YELLOW
BLACK
LCH WHITE
FRONT RCA OUTPUT
CABLE
FRONT RCA RED
VIDEO OUT 1 YELLOW
FRONT RCA WHITE
R
GROUND(B-)
L
(FOR RCA LINE OUT VERSION ONLY)
FUSE
AUTO
ANTENNA
BLUE
GREY
WHITE
FRONT
FRONT
Rch SPK.
Lch SPK.
WHITE/BLACK
GREY/BLACK
VIOLET
REAR
GREEN
REAR
Rch SPK.
Lch SPK.
GREEN/BLACK
VIOLET/BLACK
7
REMOTE CONTROL
16
3
1
15
17
2
14
23
12
18
19
5
6
8
22
4
9
20
10
11
24
7
21
25
26
13
1. CLK
2. MODE
3. STOP
4. SETUP
5. MO/ST(AUDIO)
Press it to change the display to clock display.
Press it button on the select TV ,DISC,RADIO AUX IN mode.
Press it to stop playback.
Display the SETUP menu.
In radio mode,press it to select STEREO or MONO (IN disc mode,
press it to changing of the AUDIO soundtrack on multi-audio
soundtrack DVD disc. Changing of the sound mode of the
VCD/CD disc)
Changing of the SUBTITLE language on multi-subtitle language
DVD disc. In radio mode,.Press this button for distance reception
when you are located at weak signal location, depress it for
stronger signal.
6. SUBTITLE
LO/DX
Switch the Repeat mode of DVD/VCD/CD/MP3 disc.
Disc search button, cooperatively used with numeric buttons
7. REPEAT
8. GOTO
9. /
10. SEL
Press
(In DVD mode , press continually
to skip to the next track & press
to skip back one track.
twice to skip back one track.)
Press it to change audio mode through volume ,bass,treble
balance and fader modes.
Press it to adjust volume level
11. VOL+/VOL-
/
12.
/
/
Cursor buttons in MENU mode. Note: For models without built-in
FM Modulator, the
control. In TV mode, press
to select channel upward and downward..
Press it to display the root menu of the DVD disc/Press and hold
for more than 2 seconds can have sub woofer, press it again for more
than 2 seconds to release this mode.
Display statistical disc information during playback (To change
the band in radio stations)
Press it to turn on the unit ,press it again to turn off.
Press once to pause a play, press again to resume playback.
Press it to mute down sound.
Display the TITLE menu that is stored in DVD disc changing
between PBC ON and PBC OFF on the VCD disc.(Auto store
and preset scan function in radio stations .)
Changing for slow forward/reverse playback motion
Changing of the view angle on multi-angle DVD disc.
Press it to turn to equalization function
In TV mode, Press it to search TV channel automatically.
In DISC mode, Press it to start forward rapidly.
Confirm the Track/Chapter selected with the number key or
selected with the cursor buttons on TV screen.
In TV mode, press it to ADD and DELETE channel .
In DISC mode,press it to reverse rapidly
/
buttons can be used for volume up/down
/
to fine tune. Press the
/
13.MENU
SUB WOOFER
14.BAND(OSD)
15.POWER
16.PLAY/PAUSE
17.MUTE
18.TITLE/PBC
(A/P)
19.SLOW
20.ANGLE
21.EQ
22. SEARCH
23.ENTER
24.SKIP
25. 0 - 9
26.+10
Numeric buttons.
Tens digit select button, cooperatively used with numeric buttons.
8
REMOTE CONTROL
Preparing the Remote Control
Inserting the Batteries
1.First push to inside as the direction indicated by the arrow (See )And then
1
Remove the battery holder as the direction indicated by the arrow (See ).
2
2.Replace the battery Set a new battery property with (+)side up as illustrated
(See ).
3
3.Insert the battery holder. Push in the holder to the original position(See 4 ).
Using the Remote Control
Face the remote control towards the player front face IR mark (remote control signal
receiver).
Operation angle: About 30 degree in each the direction of the front of the IR mark.
To prevent damage to the unit, be sure to follow the connection diagram
(page 7).
9
BASIC OPERATION
5
1
13
2
17
15
22 18
4
12 16 14
6
7
8
10
11
3
9
20 21
19
EJ
1.OPEN BUTTON
Press it to flip down the front panel then you can insert the cd disc into the cd
compartment. and you can find the EJ button , press it to eject the disc .
2-3.VOL+/VOL- & SEL BUTTON
Press it repeatedly to change audio mode through volume, bass, treble, balance,
and fader modes. Rotate VOL + /VOL- knob to adjust the selected mode.
(The corresponding value will show on the display.)
When mode has not been adjusted for several seconds, display returns to normal
radio or CD display.
VOL
BAS
TRE
BAL
FAD
A.Volume:Adjust volume level by using VOL + / VOL - knob..
Note: The unit is initially set to volume mode.
B.Bass:Press SEL button one time. Adjust bass level by using VOL + / VOL -
knob.
C.Treble:Press SEL button two times. Adjust treble level by using VOL + / VOL -
knob.
D.Balance:Press SEL button three times. Adjust sound balance between left
and right speakers by using VOL + / VOL - knob.
E.Fader:Press SEL button four times. Adjust sound balance between front and
rear speakers by using VOL + / VOL - knob.
10
BASIC OPERATION
4.BAND BUTTON
In RADIO mode, press the BAND button on the front panel or on the remote
control to select your desired radio band and word which band is selected will be
displayed on LCD. Press it to change the bands as below :
FM
MW
LW
FM
MW
FM
AM
For 3 Bands (Europe)
For 2 Bands (Europe)
For 2 Bands (USA)
5.EQ BUTTON
Press it to turn to equalization function and to select desired audio mode.
There are four kinds of mode as below:
JAZZ
CLAS
POP
ROCK
6-7-8-9-10-11.PRESET STATION
A.To memorize the current frequency, press any one of the six preset buttons[1-6]
on the front panel or on the remote controller hold for more than 2 seconds.
B.To recall the preset memory, press one of the preset buttons [1-6].
C.Press 1/TOP button to select the first track/chapter to play.
a.In the state of VCD/CD/MP3 disc playing, press the button on the front panel
to select the first track/chapter to play.(depend on the disc used for VCD)
b.In the state of DVD disc playing, the 1TOP button is not available.
D.Long press 2/RPT button to select repeat mode as follow.
VCD/CD:
REP-ONE
REP-ALL
DVD:
CHAPTER REPEAT ON
TITLE REPEAT ON
REPEAT OFF
a.Continuously repeat at the current chapter/track, when selected
REP-ONE mode.
b.Select REP-ALL mode to continuously repeat all chapter/track on the
current disc.
c.REPEAT feature does not support VCD2.0 (with PBC ON).
E.Long press 3/INT button to scan disc.
a.In the state of CD disc playing, press the 3/INT button on the front panel
to play the previous 6 seconds part of each track/chapter on disc.
b.In the state of DVD/MP3 disc playing, the 3/INT button is not available.
c.In the state of VCD disc playing , long press the 3/INT button, the screen will
display as follow (long press it again will release this mode.):
SELECT DIGEST TYPE:
TRACK DIGEST
DISC INTERVAL
TRACK INTERVAL
11
BASIC OPERATION
/
and then press the ENTER button to confirm .
/
/
1). You can use the
buttons on the remote control to select the item,
2). In Track Digest OR Disc/Track Interval MODE.
/
/
/
You can use the
ENTER to confirm .
buttons to select the items ,and then press the
You can also select the items using the corresponding number buttons, and
then press the ENTER to confirm .
d.In the state of DVD disc playing , long press the 3/INT button, the screen will
display as follow (long press it again will release this mode.):
SELECT DIGEST TYPE:
TITLE DIGEST
CHAPTER DIGEST
TITLE INTERVAL
CHAPTER INTERVAL
/
/
and then press the ENTER button to confirm .
/
1). you can use the
buttons on the remote control to select the item,
2). In Title/Chapter Digest OR Title/Chapter Interval MODE.
/
/
/
You can use the
ENTER to confirm .
buttons to select the items ,and then press the
You can also select the items using the corresponding number buttons, and
then press the ENTER to confirm .
F. Long press 4/RDM to play disc in random.
In the DVD/VCD/CDdisc playing, press the 4/RDM button on the front panel
to play in random (depend on the disc used for VCD).
12.AS/PS BUTTON
When shortly pressing the APS button on the front panel or the A/P button on the
remote controller, the radio searches for each preset station. When the field
strength level is more than the threshold level of stop level, the radio is holding at
that preset number for few seconds with releasing mute, and then searches again.
In FM band, FM 1,FM 2 and FM 3 is checked one at a time When long pressing the
APS or A/P button (more than 1 second), the radio searches from the current
frequency and checks the signal strength level until 1 cycle search is finished.
And then 6 strongest stations are preset to the corresponding preset number.
The AS operation is implemented in the each band of selected band. When the
AS operation is finished, the radio executes the preset scan.
13.MU BUTTON
Press it to mute down sound. Press it again to release this mode and recover
previous volume level.
14.CLK BUTTON
Press it to change the display to clock display. Press it again to return to previous
display. In clock display, press and hold for about 2 seconds until the hour display
flashes. Rotate VOL+/- button to adjust hours ,press CLK button to flash minute
then Rotate VOL+/- button to adjust minutes.
12
BASIC OPERATION
15.PWR BUTTON
Press it to turn on the unit. Press it again to turn off.
16.
BUTTON
Pressing
press
during playback will stop play temporary. Return to normal playback,
once again.
17.
/
A.When long Pressing the
BUTTONS
/
button (more than 2 seconds ) during play.The
speed of rapid forward/reverse changes according to the disc as follow.
DVD/VCD/CD/MP3:
Normal Playback 2x
4x
8x
16x
B.Shortly press the
/
button during playback to skip to next track or back
one track.(Note: In DVD mode, press continually the
back one track.)
Note:For some VCD 2.0 dics (PBC-playback control),
may be unavailable.
C.Press UP or DN button on the remote controller or
button twice to skip to
and buttons
on the fornt panel
/
to manually tune up or down for your desired station. Press them hold for more
than 2 seconds to automatically tune up or down for the stronger station.
18.MOD BUTTON
Press it repeatedly select TV, DISC ,AUX IN , RADIO mode.
19.EJECT BUTTON
In CDP playing ,Press the eject button to eject the disc form the disc slot.
20.FLASHING LED
If the front panel is not on the main unit, LED will be flashing.
21.RESET BUTTON
RESET button is placed on the housing and must be activated with either a
ballpoint pen or thin metal object. The RESET button is to be activated for
the following reasons:
A. Initial installation of the unit when all wiring is completed.
B. All the function buttons do not operate.
C. Error symbol on the display.
Note:If press RESET button , the unit can't work yet, please use a cotton swab
soaked in isopropyl alcohol to clean the socket on the back of the front panel.
22.ST BUTTON
Press ST button to select stereo or mono reception for radio stations.
13
BASIC OPERATION
MP3/WMA/JPEG DISC PLAY
1.When inserting an MP3/WMA/JPEG disc
Ex: When Mp3 file is detected.
4
5
6
1 .Current track(file)(highlighted bar)
.Current track (file) number/total
number of tracks(files) in the current
folder.
2
00:56
04:07
3
2
Repeat one
003/112
.Elapsed playing time of the current
track(not available for JPEG disc)
.total playing time.( not available for
JPEG disc)
3
4
Mp3
K
P
Mp3
Mp3
1
woman 1
ton
.Selected playback mode
.Operation mode icon.
5
6
..........n..e.w.
(Play),
(stop), (pause), (forward)
(reverse).
In stop mode , use
/
/
/
on the remote control to select the item or folder,
then press ENTER button to confirm.
Pressing REPEAT button repeatedly can select two kinds of repeat play mode.
2. REP-ONE:
Play the same song over and over again.
3. REP-ALL:
Play all songs in the discover and over again.
In the playback, use
In the playback, when long pressing the
than2 seconds ) or short press
reverse.
or
to skip an item ahead or back.
button on the front panel (more
on the remote control to rapid forward/
/
/
AUX OPERATION
When the unit connect external A/V , you can press MODE to switch the AUX
input mode.
14
BASIC OPERATION
ON-SCREEN DISPLAY FUNCTION
Press the OSD button during
playback to display the contents of the
current disc on the screen.
Example :
2.Example for VCD/SVCD/CD:
A.Press OSD for the first time:
SINGLE ELAPSED
1. DVD:
A.Press OSD for the first time:
TRACK 01/16
00:49
TITLE ELAPSED
B.Press OSD for the second time:
TT 01/01 CH 01/38
0:02:06
SINGLE REMAIN
Title Number, Total Title Number,
Chapter Number, Total Chapter Number
of this Title of the disc currently being
played will be shown on the screen,
along with the elapsed time.
TRACK 01/16
02:45
C.Press OSD for the third time:
B.Press OSD for the second time:
TOTAL ELAPSED
TRACK 01/16
00:60
TITLE REMAIN
D.Press OSD for the fourth time:
TT 01/01 CH 01/38 3:24:36
TOTAL REMAIN
C.Press OSD for the third time:
TRACK 01/16
78:46
CHAPTER ELAPSED
TT 01/01 CH 01/38 0:02:56
E.Press OSD for the fifth time:
The message on the screen will be
cleared for SVCD and VCD.
D.Press OSD for the fourth time:
NOTE:
For CD and MP3,the message will
always display on the screen.
CHAPTER REMAIN
3.Example for MP3:
Each time OSD is pressed, the message
displayed on screen changes as follows:
TT 01/01 CH 01/38 0:04:32
E.Press OSD for the fifth time:
The message on the screen will be
cleared.
SINGLE ELAPSED
SINGLE REMAIN
15
BASIC OPERATION
Multi-audio Language Function
- When no different subtitle language
are recorded, will be displayed
at screen left top corner.
For DVD:
Press AUDIO during playback.
Each time the button is pressed,
number of the audio soundtrack
language changes on sequential order.
NOTES:
- The language number is different
according to the disc.
- Some disc only contain one language
soundtrack
- When no different language
Multi-angle Function
(for DVD Only)
Press ANGLE during playback. Each
time the button is pressed, number of
the angle changes in sequential order.
Notes:
- The angle number is different
according to the disc.
- The function only work for disc having
scenes recorded at different angles.
- When no different angle are recorded,
will be displayed at screen left top
corner.
soundtrack are recorded
display at screen left top corner.
For VCD/CD:
Press AUDIO during playback. It is
possible to switch the sound between
monaural and stereo sound.
will be
TV Operation
Switching to TV mode
MONO LEFT
MONO RIGHT
STEREO
MIX-MONO
1.Connect the TV antenna to the TV.IN
(from Ant) jack on the back of the unit.
2. Press the mode button on the remote
control to select the TV mode.
Auto searching TV channels
Press the SEARCH button on the remote
controller to star search channel
automatically.
Title Menu Function
For DVD:
If the DVD has multiple titles recorded
on the disc. It can select preferred title
from the title menu to start playback.
- Press TITLE during playback.The title
menu is display.
Selecting channel
- Press the cursor button shown in TV
screen, select preferred title by the
cursor button and confirmed by
ENTER key.
- Press the
/
button to choose the
channel upward and downward.
- The numeric button (0-9) allow you to
select the corresponding channel directly.
Note:
For VCD:
In TV mode, the +10 button is not available.
Fine TV channel
Press TITLE/PBC button on the remote
control while the disc is playing, you can
switch between "PBC on"and "PBC off"
mode.
You can press
/
button on the remote
controller to fine TV channel. It can be
improve the picture quality .
Channel ADD/DEL
Multi-subtitle Language Function
(for DVD Only)
Press SUBTITLE during playback.
Each time the button is pressed, number of
the subtitle language changes in
sequential order.
Notes:
- The language number is different
according to the disc.
In TV mode ,after search channel
automatically, when you want delete the
no sign channel, press the SKIP button (the
screen display SKIP),the channel will be
deleted. Also, you can press numeric button
to select channel, then press SKIP to add
channel(the screen display SAVE).
- Some discs only contain one subtitle
language.
16
SETUP
GENERAL SETUP
--- GENERAL PAGE ---
DOLBY
DOLBY
-----General setup page----
-----General setup page----
TV Display
Normal/PS
Normal/LB
Wide
TV Display
LB
ON
Angle Mark
OSD Lang
Spdif Output
Captions
Angle Mark
OSD Lang
Spdif Output
Captions
ENG
SPDIF/RAW
ON
Screen Saver
Last Memory
Screen Saver
Last Memory
ON
ON
Set TV Display Mode
Go To General Setup Page
TV Screen
Video
Material
1. Press SETUP button on the remote
control .
Wide(16:9)
Pan Scan
Normal
Letter-box
4:3
2.The SETUP menu is displayed.
3.Select the preferred item by using the
/
/
/
buttons
4.Press ENTER button.
a.GENERAL SETUP
1.TV DISPLAY SETUP
This setup page includes the item
of TV display & audio output feature.
The detail please refer to
This is to select the appropriate TV
aspect (4:3 or 16:9) according to the
connected TV set.
GENERAL SETUP MENU.
b.SPEAKER SETUP
Normal/PS (For 4:3 TV)
Played back in the PAN & SCAN style.
(If connected to wide-screen TV, the
left and right edges are cut off.)
Normal/LB (For 4:3 TV)
This is to activate the audio output
from DOLBY AC3 5.1 DOWNMIX
to 2 channel mode. Please refer to
SPEAKER SETUP MENU.
c.DOLBY DIGITAL SETUP
Please refer to DOLBY DIGITAL
SETUP.
Played back in letterbox style.
(If connected to wide-screen TV, black
bands appear at top and bottom of the
screen.)
d.PREFERENCE SETUP
This setup page includes all the
configuration of support feature.
The detail please refer to
Wide (For 16:9 TV)
Select when a wide-screen TV set is
connected.
PREFERENCES SETUP MENU.
17
SETUP
DOLBY
DOLBY
-----General setup page----
TV Display
-----General setup page----
TV Display
ON
Angle Mark
OSD Lang
Spdif Output
Captions
Angle Mark
Osd Lang
OFF
SPDIF OFF
SPDIF/RAW
SPDIF/PCM
Spdif Output
Captions
Screen Saver
Last Memory
Set Angle Mark
Screen Saver
Last Memory
Setup SPDIF
2.ANGLE MARK DISPLAY SETUP
If it is set to ON, when the multi-angle
4.SPDIF OUTPUT
This is to activate the audio output
from SPDIF OFF mode to SPDIF/RAW
mode to SPDIF/PCM mode.
DVD disc is playing,
(the angle
mark) will appears on the screen; if is
set to OFF, the mark will not appear.
DOLBY
DOLBY
-----General setup page----
TV Display
-----General setup page----
TV Display
English
French
Angle Mark
OSD Lang
Spdif Output
Captions
Angle Mark
OSD Lang
German
Spanish
Italian
ON
Spdif Output
OFF
Captions
Screen Saver
Last Memory
Screen Saver
Last Memory
Closed Caption
Portuguese
Set OSD Language
5.CAPTIONS SETUP
3.OSD LANG TYPE SETUP
Select the preferred OSD language
Activate the CAPTIONS feature by
selecting ON. And release this feat-
ure by selecting OFF.
by using the
/
buttons.
18
SETUP
SPEAKER SETUP
--- SPEAKER SETUP PAGE ---
DOLBY
DOLBY
-----General setup page----
TV Display
-----Speaker Setup Page----
Angle Mark
OSDLang
Spdif Output
Captions
DOWNMIX
LT/RT
STEREO
ON
Screen Saver
Last Memory
Screen Saver
OFF
Set Downmix Mode
This is to activate the audio output from
DOLBYAC3 5.1 DOWNMIX to 2 channel
mode. Select the preferred SPEAKER
connection by using the cursor buttons.
Select the LT/RT to activate the Dolby
surround compatible output.
6.SCR SAVER SETUP
Select the SCR SAVER output
ON/OFF.
Select the STEREO to activate simple
stereo mode.
DOLBY
DOLBY DIGITAL SETUP
DOLBY
-----General setup page----
TV Display
-----Dolby Digital Setup----
Angle Mark
OSD Lang
Spdif Output
Captions
FULL
6/8
DYNAMIC
4/8
2/8
ON
Screen Saver
OFF
OFF
Last Memory
Set Last Memory State
Set DRC OFF
DYNAMIC RANGE CONTROL
Select DRC and adjust the dynamic
range of a Doby Digital encoded
7.LAST MEMORY SETUP
Select the LAST MEMORY output
ON/OFF.
program. There are 8 steps between
full compression and off compression.
19
SETUP
PREFERENCES SETUP
--- PREFERENCES PAGE ---
DOLBY
DOLBY
-----Preference Page----
-----Preference Page----
TV Type
PAL
TV Type
English
French
Spanish
German
AUTO
NTSC
Audio
Audio
Subtitle
Disc Menu
Parental
Password
Default
Subtitle
Disc Menu
Parental
Password
Default
Italian
Portuguese
OFF
Set TV standard
Preferred Subtitle Language
1.TV TYPE SETUP
3.SUBTITLE LANGUAGE SETUP
Select the preferred SUBTITLE
language by using the cursor buttons.
This player can play discs recorded
in either PAL or NTSC format.Select
NTSC format, when you connected to
NTSC TV.Select PAL format, when
you connected to PAL TV.Select AUTO
format, the player TV output format
will according to the DVD disc format..
DOLBY
-----Preference Page----
TV Type
DOLBY
-----Preference Page----
TV Type
Audio
English
French
Subtitle
Disc Menu
Parental
Password
Default
English
Audio
French
Spanish
German
Italian
Subtitle
Spanish
Disc Menu
German
Parental
Portuguese
Italian
Password
Portuguese
Default
Preferred Menu Language
4.DISC MENU LANGUAGE SETUP
Select the preferred DISC MENU
language by using the cursor
buttons.
Preferred Audio Language
2.AUDIO LANGUAGE SETUP
Select the preferred AUDIO sound-
track by using the cursor buttons.
20
SETUP
DOLBY
DOLBY
-----Preference Page----
-----Preference Page----
TV Type
1KID SAF
2G
TV Type
Audio
Audio
3PG
Subtitle
Disc Menu
Parental
Password
Default
Subtitle
4PG13
5PGR
6R
Disc Menu
Parental
Password
Default
7NC 17
8 ADULT
OFF
RESET
Load Fcatory Setting
Set Parental Control
7.DEFAULTS
Select reset to become factory initial
setting.
5.PARENTAL
Select suitable parental guidance by
the cursor buttons and conformed by
pressing ENTER button.
DEFAULTS TABLE
DOLBY
TV DISPLAY
NORMAL/LB
ON
-----Preference Page----
TV Type
ANGLE MARK
OSD LANGUAGE
ENGLISH
SPDIF/RAM
ON
GENERAL SETUP
Audio
SPDIF OUPUT
CAPTIONS
Subtitle
Disc Menu
Parental
SCR SAVER
ON
LAST MEMORY
ON
DOWNMIX
SPEAKER SETUP
DOLBY DIGITAL
STEREO
OFF
Password
Default
CHANGE
DYNAMIC
TV TYPE
AUDIO
AUTO
ENGLISH
OFF
Change Password
SUBTITLE
6.PASSWORD
DISC MENU
Select the change and press ENTER
button. Type the old password (The
initial factory code is 1379) and key
in 4 characters password now you
want to use, and retype again to
confirm key in correctly.
PREFERENCES
ENGLISH
8 ADULT
1379
PARENTAL
PASSWORD
21
SPECIFICATION
GENERAL
Supply Voltage
Current Consumption
SIGNAL SYSTEM
:12v Dc (11v-15v)
:More Then 10 A
:Compositive Video 1.0vp-p 75
DISCS PLAYED
(1)Dvd-video Disc
5"(12 Cm) Single-sided, Single-layer
5"(12 Cm) Single-sided, Double-layer
(2)Compact Disc (cd-da, Video Cd)
5"(12cm) Disc
AUDIO SIGNAL OUTPUT
CHARACTERISTICS
:2ch&4ch Line Out
(1)Frequency Response 20 Hz - 20 Khz
(2)S/n Ratio
90 Db (jis)
(3)Wow And Flutter
Below Measurable Limits
RADIO
FM TUNER SECTION
Tuning Range
:87.5-107.9MHz
:10.7MHz
IF Range
Usable sensitivity(30dB)
AM TUNER SECTION
Frequency Range
IF Range
:15dB
:530-1710KHz
:450KHz
Usable sensitivity(30dB)
:45dB
TV TUNER
TV System
TV Sensitivity
:NTSC or PAL
:
NOTE:
Specifications and design are subject to modification, without notice, due to
improvements in technology.
22
TROUBLE SHOOTING
Before going through the check list, check wiring connection. If any of the problems
persist after check list has been made, consult your nearest service dealer.
SYMPTOM
NO POWER
CAUSE
SOLUTION
If the power supply is properly
connected to the car accessory
terminal,switch the ignition key
to "ACC"
The car ignition switch is
not on
Replace the fuse
The fuse is blown
Remove the disc in the player,
then put a new one
Presence of disc inside the
player.
Insert the compact disc with
the label facing upward
Inserting the disc in reverse
direction
DISC CANNOT
BE LOADED
OR EJECTED
The disc is extremely dirty
or defective
Clean the disc or try to play a
new one
Temperature inside the car Cool off or until the ambient
is too high
temperature return to normal
Leave the player off for an hour
then try again
Condensation
Volume is in minimum
Adjust volume to a desired level
Check wiring connection
NO SOUND
Wiring is not properly
connected
The installation angle is
more than 30 degrees
Adjust the installation angle less
than 30 degrees
SOUND SKIPS
Clean the compact disc, then
try to play a new one
The disc is extremely dirty
or defective disc
Press the RESET button.
Front panel is not properly fixed
into its place
The built-in microcomputer
is not operating properly
due to noise
THE OPERA-
TION KEYS
DO NOT WORK
The antenna cable is not
connected
THE RADIO
DOES NOT
WORK
Insert the antenna cable firmly
Select a station manually
The signals are too weak
888-J9080-04
23
|