PLCD19XMR
OWNER’S MANUAL
Mobile Audio System
• PLL Synthesizer Stereo Radio
• Digital Compact Disc Player
• XM Ready Function
• Automatic Memory Storing
• Slide Down Detachable Panel
• Direct Track Access
• Program CD Tracks
• CD Changer Control
• Auxiliary Input Function
• Wired Commander Control
INSTALLATION
Notes:
TAKE OUT SCREWS BEFORE
INSTALLATION
• The unit can be installed on the vehicle
or the ships.
Before install the unit, please remove the
two screws.
• Choose the mounting location where
the unit will not interfere with the normal
driving function of the driver.
Take out screws before installation
• Before finally installing the unit, connect
the wiring temporarily and make sure
it is all connected up properly and the
unit and the system work properly.
• Use only the parts included with the
unit to ensure proper installation. The
use of unauthorized parts can cause
malfunctions.
NOTE: If this unit is installed on the ship,
you should use two pieces of plastic film
(30mmX20mm) supplied with the unit to
seal the two holes after remove the
screws. And this will be waterproof.
• Consult with your nearest dealer if
installation requires the drilling of holes
or other modifications of the vehicle or
the ship.
• Install the unit where it does not get in
the driver’s way and cannot injure the
passenger if there is a sudden stop,
like an emergency stop.
DIN FRONT-MOUNT
Installing the unit
• If installation angel exceeds 30¢Xfrom
horizontal, the unit might not give its
optimum performance.
1
2
53
30˚
3
• Avoid installing the unit where it would
be subject to high temperature, such
as from direct sunlight, or from hot air,
from the heater, or where it would be
subject to dust, dirt or excessive
vibration.
(Fig. 1)
1. Dashboard
2. Holder
After inserting the holder into the
dashboard, select the appropriate tab
according to the thickness of the
dashboard material and bend them
inwards to secure the holder in place.
3. Screw
3
INSTALLATION
Removing the unit
1
6
1
2
5
3
7
4
Front Panel
OPEN button
(Fig. 2)
2
1. Dashboard
2. Nut (5mm)
3. Spring washer
4. Screw (5x25mm)
5. Screw
6. Strap
Be sure to use the strap to secure the
back of the unit in place. The strap can
be bent by hand to the desired angle.
7. Plain washer
1. Before removing the unit, press the
OPEN button to slide down the front
panel.
2. Lever
Insert the levers supplied with the unit
into the grooves in the housing as
shown in figure until they click. Pulling
the levers makes it possible to remove
the unit from the dashboard.
4
USING THE DETACHABLE FRONT PANEL
To Detach the Front Panel
To Reinstall the Front Panel
1. Press the OPEN button, the front panel
1. When the panel bracket is in slide down
position, insert the front panel into the
panel bracket and push the front panel
from the middle to slide it up.
will slide down.
Open
Bottom
Button
2. When the front panel slides down,
press the bottom button of the front
panel upward and pull it out from the
panel bracket.
Bottom
Button
3. For safekeeping, store the front panel
in the supplied protective case
immediately after being removed.
Protective Case
Front Panel
5
WIRING CONNECTION
XM AUDIO CABLE(BLACK)
(BLACK)
AUDIO R IN (RED)
AUDIO L IN (WHITE)
XM RECEIVER CONNECTOR SOCKET (BLACK)
WIRING REMOTE
CONNECTOR SOCKET
(BLACK)
CD CHANGER
CONNECTOR SOCKET
FUSE
RED RCH
WHITE RCH
AUX IN CABLE (YELLOW)
ANTENNA CONNECTOR
6
OPERATION
CONTROL & FUNCTIONS KEYS
1
8
6
5
2
3
4
7
This unit is a marine rated wired remote control made using a modified controller or
similar layout. It is capable of operation specified functions on the marine AM/FM/CD
receiver. The body, buttons, controls and display need to be UV and water-resistant.
It includes and LCD and an illumination circuit. The flat body should be watertight and
the circuit board clear coated.
1 Power button
Press the button (1) shortly to turn on/off the head unit.
Press button (1) for more than 3 seconds, the button is operated to initial volume
control button. When system power turns on, the volume is set to initial volume
level.
2 MUTE button
In RADIO/AUX IN mode, press MUTE
/
button (2) to activate mute function and
“MUTE” will appear on the display. Press the button once again to release mute
function and return the volume to the last position before it was muted.
In CD/CDC mode, press
again to resume play.
/
MUTE button (2) to pause CD/CDC player. Press it
3 VOLUME +/- buttons
Press VOL
/
buttons (3) to increase/decrease volume level.
7
OPERATION
4 MODE SELECTION button
Press the MODE button (4) to step sequentially through the following sources:
e.g. radio mode to CD mode to CDC mode to AUX in mode.
5 BAND SELECTION button
Press the BAND button (5) to step sequentially through the following bands: FM1,
FM2, FM3, AM1, AM2.
6 TRACK/SEARCH/TUNE buttons
• STATION SELECTION (FOR RADIO OPERATION)
Press
/
buttons (6) shortly to activate automatic seek function. Press for
more than 3 seconds until “MAN” appears on the display, the manual tuning
mode is selected. If both buttons have not pressed for several seconds, they
will return to seek tuning mode and “AUTO” appears on the display.
• SELECT TRACKS (FOR CD OR CDC OPERATION)
Press the
track.
/
buttons (6) shortly to move to the following track or the previous
Press the
/
buttons (6) for more than 3 seconds to activate fast forward or
rewind of the disc. Disc play starts from when you release the button.
7 SHIFT/SCAN button
• SCAN (FOR RADIO OPERATION)
Press SHIFT/SCAN button (7) to scan through strong stations in the current
band. Radio pauses for five seconds at each strong station. At each time the
frequency is flashing on the display. Press SHIFT/SCAN button (7) again to
listen to current station.
• SELECT DISC (FOR CDC OPERATION)
During CDC operation, press SHIFT/SCAN button (7) to shift mode. And then
“SHIFT” will appear on the display. At shift mode, press
/
buttons (6) to
select next disc or previous disc. If there is not any operation for several seconds,
it will exit shift mode automatically.
8 Liquid Crystal Display
Exhibit the number, the current disc and the current track, and other activated
functions on the display (8).
8
INSTALLATION
INSTALLATION HARDWARE
HOLDER
BASE
REMOTE
MOUNTING BRACKET
X1
X1
X1
SCREW (ø4X50)
NUT
X2
X2
INSTALLATION DIAGRAM
1. First insert the hooks on the base into
the slots of the holder to install the base
to the holder.
2. Select the proper object, then place the
remote mounting bracket on the base
and let the object go through the base
and the mounting bracket.
3. Align the screw holes on the holder with
the screw holes on the base and the
screw holes on the bracket, then use the
two screws (ø4X50) and nuts to fix the
bracket, the base and holder to the proper
location.
4. Last install the remote control to the
holder. See below, align the four hooks
on the holder with the four slots on the
remote control.
9
OPERATION
LOCATION OF KEYS
16
9
11 10 17
8
1
18
4
15
6
12 13 19
20
21 14 22
5
23
24
2
3
7
25
1. DISP
2. AS/PS/ELAPSE
14. M1~M6 Preset buttons
15. LOUD/DIM
16. CH
/
3.
4.
/MUTE
EJ
17. CH
18. BAND/ENTER
19. M1 MEM (CAT )
20. M2 PGM (CAT )
21. M3 RPT
22. M4 SHF
23. M5 SCN
5. DISC SLOT
6. MODE
7. OPEN
8. LIQUIID CRYSTAL DISPLAY
9. PWR
10. SEL/MENU
11. VOL
24. M6
25. Reset Button
12. VOL
13. SHIFT/SCAN/XM-MOD
10
OPERATION
select different set mode and separately
to press VOL button (11) or VOL
button (12) to select your requisite as
following order.
GENERAL OPERATION
SWITHCHING ON/OFF THE UNIT
Pressing PWR button (9) to switch on or
turn off the unit. When system power turns
on, the system is returned to previous
mode.
BEEP ON/OFF
CLOCK ON/OFF WHILE POWER OFF
FREQ/CLOCK/NO PRI PRIORITY
PROGRAM POWER ON VOLUME LEVEL
USA/EUR
12 HOURS/24 HOURS
FACEPLATE RELEASE
For detailed operations, please see below:
BEEP ON/OFF
Press OPEN button (7) to slide down the
removable faceplate.
Hold press SEL/MENU button (10) for
several seconds, when BEEP ON/OFF
appears, press VOL button (11) or VOL
button (12). to select BEEP on or BEEP
OFF. When beep on, the beep in generated
when every button is pressed. When beep
off, the beep is disabled when press any
button.
SOUND ADJUSTMENT
Press SEL/MENU button (10) shortly to
change audio mode through volume, bass,
treble, balance, and fader mdoes, Press
VOL button (11) or VOL button (12)
to adjust the selected mode. When the
currently displayed function has not been
adjusted for several seconds, the mode
shall return to volume position and display
will return to normal radio, CD or CDC
display.
Program power on volume level
Hold press SEL/MENU button (10) for
several seconds, when BEEP ON/OFF
appears, press SEL/MENU button (10)
shortly one time to select “program power
on volume level” mode. And then you can
press VOL button (11) or VOL button
(12) to select the level when the unit turns
on.
Volume
Bass
Treble
Balance
Fader
Volume
Press SEL/MENU button (10) one time.
Adjust volume level by VOL button (11)
or VOL button (12).
USA/EUR
Hold press SEL/MENU button (10) for
several seconds, when BEEP ON/BEEP
OFF appears, press SEL/MENU button
(10) shortly two times to select “USA/EUR”
mode. And then you can press VOL
button (11) or VOL button (12) to select
USA or European radio frequency spacing.
- USA radio spacing is 200k for FM and
10k for AM. This is the default frequency
spacing.
Notes:
The unit is initially set to volume mode.
Bass
Press SEL/MENU button (10) two times.
Adjust bass level by VOL button (11) or
VOL button (12).
Treble
Press SEL/MENU button (10) three times.
Adjust treble level by VOL button VOL
button (11) or VOL button (12).
Balance
- European radio spacing is 50k for FM
and 9k for AM.
Press SEL/MENU button (10) four times.
Adjust sound balance between left and
right speakers by VOL button (11) or
VOL button (12).
CLOCK ON/OFF while power off
Hold press SEL/MENU button (10) for
several seconds, when BEEP ON/OFF
appears, press SEL/MENU button (10)
shortly three times to select “clock on/off
while power off” mode. And then you can
press VOL button (11) or VOL button
(12) to select if the clock is to be displayed
while power off.
Fader
Press SEL/MENU button (10) five times.
Adjust sound balance between front and
rear speakers by VOL button (11) or
VOL button (12).
FREQ/CLOCK/NO PRI priority
Hold press SEL/MENU button (10) for
several seconds, when BEEP ON/OFF
appears, press SEL/MENU button (10)
shortly four times to select
MENU SELECTION FUNCTION
Hold press SEL/MENU (10) for several
seconds to enter menu select function,
then step short press SEL/MENU (10) to
11
OPERATION
“FREQ/CLOCK/NO PRI priority” mode.
And then you can press VOL button (11)
or VOL button (12) to select frequency
priority or clock priority or no priority.
- When select Frequency Priority:
The frequency will appear on the unit
all the while. Pressing DISP button (1)
while in Frequency Priority will temporarily
display clock and then returns to
frequency display.
SET THE CLOCK
Press the DISP button (1) shortly until the
clock is shown on the LCD display. Then
hold down DISP button (1) until the clock
flashes. Then press the CH button (17)
clockwise to change hours or rotate the
CH button (16) to change minutes.
MUTE
In radio/XM/AUX IN mode, press
/MUTE button (3) to mute audio level.
Press the button again to release mute
function.
- When select Clock Priority:
The clock will appear on the unit all the
while. Pressing DISP button (1) while in
Clock Priority will temporarily display
selected station frequency (in RADIO
mode) or track number (in CD/CDC
mode) and then returns to clock display.
- When select No Priority:
When the frequency appears on the unit,
pressing DISP button (1) will display
clock and it will not return to frequency
display until DISP button (1) pressed
again. When the clock appears on the
unit, pressing DISP button (1) will display
frequency information.
LOUDNESS
Press LOUD (DIM) button (15) shortly to
reinforce the bass output and display will
show “LOUD”. Press it again to release
this function.
MODE SELECTION
Press MODE button (6) to sequence through
primary operating modes in the following
order: radio >XM > CD> CDC> AUX.
If playback media (CD) is not loaded into
mechanism, CD mode will be skipped. If
CDC is not connected to head unit, CDC
mode will be skipped.
12hours/24hours
Hold press SEL/MENU button (10) for
several seconds, when BEEP ON/OFF
appears, press SEL/MENU button (10)
shortly five times to select
If XM receiver connector is disconnected
to XM head unit, XM mode will be skipped.
LIQUID CRYSTAL DISPLAY
Exhibit current frequency and activated
functions on the display (8).
“12hours/24hours” mode. And then you
can press VOL button (11) or VOL
button (12) to set 24 hours mode or 12
hours mode.
- When the currently displayed function
has not been adjusted for several
seconds, it will exit menu set mode.
- When you have set CLOCK ON during
power off state, LCD backlight will be
turn on together.
ILLUMINATION
Press LOUD (DIM) button (15) for more
than 2 seconds to adjust the brightness
of the LCD display backlight.
RESET FUNCTION
Reset button (25) must be activated with
either a ballpoint pen or thin metal object.
The reset button is to be activated for the
following reasons:
DISPLAY INFORMATION
When pressed quickly, the DISP button
(1) changes the display as follows.
- In AM/FM mode:
- Initial installation of the unit when all
wiring is completed.
- All the function buttons do not operate.
- Error symbol on the display.
Note: If press reset button (25), the unit
can’t work yet, please use a cotton swab
soaked in isopropyl alcohol to clean the
socket on the front panel.
-> Frequency ->CLOCK ->
- In XM mode:
-> Channel Name -> Artist Name ->
Song Title -> Category Name -> CLOCK
->
- In CD mode:
-> CD ->CLOCK ->
RECOVERING INITIAL VALUE
- In CDC (or AUX) mode:
->CDC (or AUX)->CLOCK ->
Each display time is 5 seconds, the display
will return to the first position after 5
seconds.
In radio (AM/FM) mode, press MODE
button (6) for more than three seconds,
the display will appear “EEP INIT”, and all
settings recover factory value.
12
OPERATION
until the corresponding preset button
number appears. Repeat steps 1 and
2 to program additional stations.
RADIO OPERATION
SWITCHING TO RADIO MODE
Press MODE button (6) shortly to select
radio mode, the radio mode appears in
the display together with the memory
band and frequency.
- Quick tuning
Select the desired band, then press one
of the ten preset buttons (14).
SCAN
Press SHIFT/SCAN button (13) to set
function to scan mode, which scanning
to higher frequency station with receivable
signal and keep on each station for several
seconds.
SELECTING THE FREQUENCY BAND
At radio mode, press BAND/ENTER
button (18) shortly to select the desired
band.
The reception band will change in the
following order:
FM1
FM2
FM3
AM1
AM2
XM OPERATION
SWITCHING TO XM MODE
Shortly press MODE button to select XM
mode.
SELECTING USER-PRESET CHANNEL
In XM mode, the XM user-preset channel
group is toggled cyclically through the
group by quickly pressing the BAND
button.
SELECTING STATION
Press CH button (16) or CH button
(17) shortly to activate automatic seek
function. Press for more than 3 seconds
until “MANUAL” appears on the display,
the manual tuning mode is selected.
If both buttons have not been pressed for
several seconds, they will return to seek
tuning mode and “AUTO” appears on the
display.
The channel will change in the following
order:
XM1
XM2
XM3
AUTOMATIC MEMORY STORING &
PRSET SCAN
SELECTING CHANNEL UP/DOWN
buttons to select the
channel up or down.
- Automatic memory storing
Press AS/PS button (2) for serveral
seconds, the radio searches from the
current frequency and checks the signal
strength until one cycle search is
finished. And then 10 strongest stations
are stored into the corresponding preset
number button
Press the CH
/
SEARCHING SCHANNEL
When the AS/PS button is shortly pressed,
the unit searches for each user preset
channel from XM1 , XM2 to XM3. When
an available channel is detected, the
channel will be held at that preset number
and played about 5 seconds. After that,
it will search for another available channel.
- Preset Scan
Press AS/PS button (2) shortly to scan
all station presets saved in memory.
DIAGNOSTIC MODE
STATION STORING
Press and hold AS/PS button for over 5
seconds will enter diagnostic mode and
display “STATE1”, then press channel
UP/DOWN key to select each state as
below:
->STATE1->STATE2->STATE3->STATE4
->STATE5->STATE6->STATE7-> STATE8
->STATE9
Short press AS/PS button will exit
diagnostic mode.
The preset buttons (14) can be used to
store 10 stations in each band (FM 1, FM
2, FM 3 and AM1, AM2) for convenient
access to your favorite stations.
- Programming stations
1. Select the desired band, then tune
in the station you want to store in
memory.
2. Press and hold one of the preset
buttons (14) for more than 2 seconds
13
OPERATION
STORING PRESET CHANNELS
The preset buttons can be used to store
channels for convenient access to your
favorite channels.
6.Use CH button, CH button or directly
press numeric buttons(0-9) to select
1s digit.
7.Press BAND button to confirm direct
tune. If selected a nonexistent channel,
after the channel number was entered,
each digit will be converted to dashes
for 2s, then the display will return to the
previous channel and settings.
- Programming channels
1.Select the desired channel you want to
store in memory.
2. Press and hold one of the preset buttons
for more than 2 seconds until the
corresponding preset button number
appears. Repeat steps 1 and 2 to
program additional channels.
- Quick tuning
CD OPERATION
Shortly press one of the preset buttons
to select a preset channel directly.
SWITCHING TO CD MODE
If there is no CD inserted in the driver:
Gently insert the CD with the printed side
uppermost into the CD compartment
until you feel some resistance. The CD
is drawn into the driver automatically.
CD playback begins.
MODE SELECTION
Press XM-MOD button to switch
CATEGORY mode, DIRECT mode, or
NORMAL mode. Its sequence is as follows:
Normal
Category mode
Direct Tune
If a CD is already inserted in the driver:
Keep pressing MODE button (6) shortly
until the CD mode display appears.
When category mode is selected, the
CATEGORY appears on the display and
the function is activated.
When Category mode is released, the
CATEGORY disappears. When Direct
mode is engaged, “DIRECT” of
alphanumeric display is turned on.
Select category and tune UP/DOWN
within selected category
EJECTING A DISC
Press (EJECT) button (4) to stop CD
playing and eject the disc from the disc
slot (5).
PAUSING PLAYING
Press / /MUTE button (3) to pause CD
player. Press it again to resume play.
Use M1 button or M2 button to select
desired category and press BND/ENT
button to confirm.
SELECTING TRACKS
Press CH button (16) or CH button
(17) to move to the previous track or the
following track. Track number shows on
display.
Hold press CH button (16) or CH
button (17) to fast reverse or fast forward.
Disc play starts from when you release
the button.
In CATEGORY mode, channels can be
tuned by press CH button (16) or CH
button (17) within the same category.
How to direct tune
Press XM-MOD to select DIRECT MODE.
1.In direct mode, display shows “CH000”
channel number. (Hundred Digit flashing
on/off)
2.Use CH button, CH button or directly
press numeric buttons(0-9) to select
hundred digit.
3.Press XM-MOD button to confirm entry
of the hundred digit and the 10s digit is
flashing on/off.
4.Use CH button, CH button or directly
press numeric buttons (0-9) to select
10s digit.
5.Press XM-MOD button to confirm entry
of the 10s digit and the 1s digit is flashing
on/off.
DIRECT TRACK ACCESS
Pressing number buttons 0~9(14) (i.e.
19~28) can activate DIRECT TRACK
ACCESS according to your need. For
example, press button (19), and “T-01”
will be flashing on the display. Then press
button (20), “T-12” will appear and track
12 will be selected to play. If you don’t
press any button when “T-01” is flashing.
After several seconds, “T-01” doesn’t
flash and track 1 is selected to play. If
14
OPERATION
you select a track number that doesn’t
belong to the current disc, “NO TR” will
appear on the display.
tracks to be programmed. “FULL” will
appear on the display.
- When the CD is played in
programmed order by hold pressing
PGM button (20) for several
seconds, hold pressing it again for
several seconds will exit PGM
mode.
REPEATING THE SAME TRACK
Hold press RPT button (21) for several
seconds to continuously repeat the same
track. Hold press it again to stop repeat.
- When the disc is playing in
programmed order, hold pressing
MEM button (19) for several
seconds will cancel the all
programmed content and “CLEAR”
appears on the display.
- If you don’t press MEM button (19)
to carry out program setting, then
hold press PGM button (20) for
several seconds, “NO-PGM” will
appear.
PLAYING ALL TRACKS IN RANDOM
Hold press SHF button (22) for several
seconds to play all tracks on CD in
random order. Hold press again to cancel
the function.
PREVIEWING ALL TRACKS
Hold press SCN button (23) for several
seconds to play first several seconds of
each track on the current disc. Hold
press again to stop intro and listen to
track.
TRACK/TIME DISPLAY
Press AS/PS button (2) to show running
time/remain time of track.
PROGRAM CD TRACKS
Use Program function to select up to 32
tracks to play in any order. Program
works by allowing you to select a track
number for each spot in the playing
sequence. A CD must be inserted and in
CD playing mode to use Program.
CDC OPERATION
You can connect a CD changer to the
unit with CDC operation version only.
Information on handing CDs, inserting
CDs and operating the CD changer can
be found in the operating instructions
supplied with your CD changer.
- How to program CD tracks.
1. Hold press MEM button (19) for
several seconds to enter Program
mode, then “PGM” stars flashing and
“P-01” icon appear on the display.
2. Press CH button (16) or CH button
(17) to choose track number. For
example, select track 6, then press
MEM button (19) shortly to memorize
it and “P-02” will appear on the
SWITCHING TO CDC MODE
Keep pressing MODE button (6) shortly
until the CDC mode display appears.
Playback begins with the first CD that
the CD changer detects.
PAUSING PLAYING
display. So track 6 will be played first.
Press
/MUTE button (3) to pause
Thus, you can also press CH
/
CDC player. Press it again to resume
play.
buttons (17) and (16) to choose track
number 10 and press MEM button
shortly, then “P-03” will appear. So
track 10 will be secondly played.
Repeat these operations, and you can
program CD tracks to your need. If
you completed program setting, hold
press PGM button (20) for several
seconds to play CD in programmed
order.
SELECTING TRACKS
Press CH button (16) or CH button
(17) to move to the previous track or the
following track. Track number shows on
display.
Hold press CH button (16) or CH
button (17) to fast reverse or fast forward.
Disc play starts from when you release
the button.
Note: Using Program function can
only select up to 32 tracks to play in
any order. When you have selected 32
15
OPERATION
DIRECT TRACK ACCESS
DISC NOTE
Pressing number buttons 0~9(14) (i.e.
19~28) can activate DIRECT TRACK
ACCESS according to your need. For
example, press button (19), and “T-01”
will be flashing on the display. Then press
button (20), “T-12” will appear and track
12 will be selected to play. If you don’t
press any button when “T-01” is flashing.
After several seconds, “T-01” doesn’t flash
and track 1 is selected to play. If you
select a track number that doesn’t belong
to the current disc, “NO TR” will appear
on the display.
A. Notes on discs:
1.Attempting to use non-standard shape
discs (e.g. square, start, heart) may
damage the unit. Be sure to use round
shape CD discs only for this unit.
2.Do not stick paper or tape etc., onto
the label side or the recording side of
any discs, as it may cause a
malfunction.
3.Dirt, dust, scratches and warping discs
will cause misoperation.
B. Notes on CD-Rs (recordable
CDs)/CD-RWs (rewritable CDs):
1.Be sure to use discs with following
marks only for the unit to play:
REPEATING THE SAME TRACK
Hold press RPT button (21) for several
seconds to continuously repeat the same
track. Hold press it for several seconds
again to stop repeat.
Recordable
Rewritable
PLAYING ALL TRACKS IN RANDOM
Hold press SHF button (22) for several
seconds to play all tracks on the current
disc in random. Hold press it for several
seconds again to cancel the function.
2.The unit cannot play a CD-R and
CD-RW that is not finalized.
(Please refer to the manual of your
CD-R/CD-RW recorder or CD-R/
CD-RW software for more information
on finalization process).
3.Depending on the recording status,
conditions of the disc and the
equipment used for the recording,
some CD-Rs/CD-RWs may not be
played on this unit. (See *1)
PREVIEWING ALL TRACKS
Hold press SCN button (23) for several
seconds to play first several seconds of
each track on current disc. Hold press it
again for several seconds to stop intro
scan and listen to track.
*1: To have more reliable play back,
please see following
TRACK/TIME DISPLAY
Press AS/PS (ELAPSE) button (2) to show
running time of track.
recommendations:
a.Use CD-RWs with speed 1x to 4x
and write with speed 1x to 2x.
b.Use CD-Rs with speed 1x to 8x and
write with speed 1x to 2x.
c.Do not play a CD-RW which has
been written for more than 5 times.
SELECTING DISC
Press SHIFT/SCAN button (13) to shift
mode and then “SHIFT” will appear on
the display. At shift mode, press CH
button (16) or CH button (17) to select
previous disc or next disc. If there isn’t
any operation for several seconds, it will
exit shift mode automatically. At shift
mode, you can also press number button
0~9 (14) (i.e. 19~28) to select the disc
directly. If you select 3# disc (press button
(21), and there isn’t a disc in the 3# slot,
“NO CD” will appear.
16
SPECIFICATION
GENERAL
Power Supply Requirements
Chassis Dimensions
Tone Controls
: DC 12 Volts, Negative Ground
: 178 (W) x 178 (D) x 50 (H) mm
- Bass (at 100 Hz)
- Treble (at 10 KHz)
Maximum Output Power
Current Drain
:
:
10 dB
10 dB
: 4 x 50 Watts
: 15 Ampere (max.)
CD PLAYER
Signal to Noise Ratio
Channel Separation
Frequency Response
: More than 60 dB
: More than 50 dB
: 40 Hz - 18 KHz
RADIO
FM
Frequency Coverage
IF
Sensitivity (S/N = 30 dB)
Stereo Separation
: 87.5 to 107.9 MHz
: 10.7 MHz
: 3 µV
: > 30 dB
AM
Frequency Coverage
IF
Sensitivity (S/N = 20 dB)
: 530 to 1720 KHz
: 450 KHz
: 32 dBu
17
TROUBLE SHOOTING
Before going through the check list, check wiring connection. If any of the problems
persist after check list has been made, consult your nearest service dealer.
Symptom
No power.
Cause
Solution
The car ignition switch is
not on.
If the power supply is
connected to the car accessory
circuits, but the engine is not
moving, switch the ignition key
to “ACC”.
The fuse is blown.
Replace the fuse.
Disc cannot be
loaded or ejected. the player.
Presence of CD disc inside Remove the disc in the player,
then put a new one.
Inserting the disc in reverse Insert the compact disc with
direction. the label facing upward.
Compact disc is extremely Clean the disc or try to play a
dirty or defective disc. new one.
Temperature inside the car Cool off or until the ambient
is too high.
temperature return to normal.
Condensation.
Leave the player off for an hour
or so, then try again.
No sound.
Volume is in minimum.
Adjust volume to a desired level.
Check wiring connection.
Wiring is not properly
connected.
Sound skips.
The installation angle is
more than 30 degrees.
Adjust the installation angle less
than 30 degrees.
The disc is extremely dirty
or defective disc.
Clean the compact disc, then
try to play a new one.
The operation keys The built-in microcomputer Press the RESET button.
do not work.
is not operating properly
due to noise.
Front panel is not properly fixed
into its place.
The radio does not The antenna cable is not
Insert the antenna cable firmly.
work. The radio
station automatic
selection does not The signals are too weak.
work.
connected.
Select a station manually.
88-C1802-17
18
|