7INCH WIDE TFT LCD MONITOR
Control and layout for the monitor
Notice: some functions are work by remote control.
2
Control and layout for the remote control
Notice: If the monitor does not have the function, the button would not be work.
3
Function
Press FUNCTION button< > on the remote or press manual button< > twice from
the monitor to call out the function menu.
Fixed
Press left < > or right < >
button to select your favorite
FUNCTION
display language
PRESS UP < > OR
DOWN < > BUTTON
TO SELECT
Press left button < >to adjust
hours & press right button < >to
adjust minute
Press left or right button <
>
to select auto on/off
Press left or right button <
to call out the calender
>
Press the left or right button <
to call out the game
>
Press <
> to invert the
picture left or right
Press <
> to invert the
picture up or down
Games
Press <
> to enter the games.
Start --Menu Button < >
Move --Down Button < >
Roll --Up Button < >
Exit --Mute Button < >
Level --AV Button < >
Pause --Menu Button < >
Move Left --Volume Button < >
Move Right --Volume Button < >
Calendar
Press FUNCTION < >to call out the function menu,
then Press <
press left or right to <
> to select CALENDAR and
> to call out the CALENDAR
Adjust increase of year, press < > button
Adjust decrease of year, press < > button
Adjust increase of month, press < > button
Adjust decrease of month, press < > button
Installation
Power Cord
(Female)
Video 1 input (red)
Video 2 input (yellow)
Ground (black)
DC 12V power input (red)
Remote Control replacing batteries
PULL OUT
PUSH
1)Always use new batteries when replacing the old set.
2)Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.
3)Battery replacement is necessary when remote control acts sporadically or stops
operating.
4)Do not drop, apply shock or step on the remote control
5)Do not spill water on the remote control
6) Do not place objects between the remote control and remote sensor.
7)Do not use remote controls for other equipments at the same time.
8)If the MONITOR does not operate even when operating the remote control from
a close range, it is time to replace the batteries (use CR-2025), refer to the label
on back of the basic control.
4
Unscrew it and takeaway the back cover before
install to headrest housing or sun-visor housing
CAUTION: make sure the screw are not long
enough to go through the headrest!
If you have any doubts about this type of
installation, please consult your local mobile
electronics retailer. Cutting and make holes in
the headrest will cause damage which is
expansive to repair.
Step of install headrest housing
Setup work
remove the headrest and set it in an uncluttered
work area. Take the appropriate precautions to
ensure that it is not damaged during the installation.
6
Measurements
Push on the headrest with your fingers to make
sure there are no obstructions that would hinder
the installation. Use the paper template to mark
the area to be cut.
Cut the headrest
using an adjustable-depth blade, start
your cut 1/4 inch inside one corner and
cut diagonally across, stopping 1/4 inch in
from the other corner. Repeat the procedure
for the other two corners.
Remove foam & obstructions
Carefully peel back the material. Set the
adjustable blade to one inch depth and cut
around the edges of the hole, staying 1/4 inch
inside the edge. Pull up one corner of the foam
and use the blade to cut underneath. Remove
small section at a time, using the pull up and
cut method for uniform depth. Use a dremel or
other appropriate tool to remove other
obstructions. Insert the monitor to measure the
fit and make adjustments if necessary
7
Step of install sun-visor housing
Setup work
remove the visor and set it in an uncluttered
work area. Take the appropriate precautions to
ensure that it is not damaged during the installation.
Measurements
Push on the headrest with your fingers to make
sure there are no obstructions that would hinder
the installation. Use the paper template to mark
the area to be cut.
Cut the visor
using an adjustable-depth blade, start
your cut 1/4 inch inside one corner and
cut diagonally across, stopping 1/4 inch in
from the other corner. Repeat the procedure
for the other two corners.
9
Remove foam & obstructions
Carefully peel back the material. Set the
adjustable blade to one inch depth and cut
around the edges of the hole, staying 1/4 inch
inside the edge. Pull up one corner of the foam
and use the blade to cut underneath. Remove
small section at a time, using the pull up and
cut method for uniform depth. Use a dremel or
other appropriate tool to remove other
obstructions. Insert the monitor to measure the
fit and make adjustment if necessary
Route the cable through the visor
Run the supplied cable through the opening
and out the top of the visor. If possible,
conceal the wires using a shaft covering.
Connect the power, ground and video leads to
test the MONITOR.
Before connecting the monitor, pull the
connecting cable assembly through the
visor housing as shown in diagram. Place
visor housing into the opening and secure with
correct fasteners.
Install the sun-visor housing
Pull the connecting cable through the center of
the housing as shown in diagram, and secure with
correct fasteners
Download from Www.Somanuals.co1m0. All Manuals Search And Download.
Technical parameters
LCD Drive Method: TFTActive Matrix
Display Size: 7 Inch Wide Screen (Diagonal)
Aspect: 16:9
Display Format: 480 x RGB x 234
Number of Pixels: 1440 x 234
Video System Input: NTSC/PALAuto-select
Back Light: High Brightness Type U Shaped CCFT
Power Source: DC12V
Current Consumption: 8W
Dimension (H x W x D): 113 x 182 x 25 (mm) Stand Style
Dimension (H x W x D): 128 x 195 x 24 (mm) Headrest Style
Dimension (H x W x D): 127 x 236 x 25 (mm) Sun Visor Style
|